Page 1
Operating
Instructions
Warning:
Always wear safety glasses when operating hand tool.
Instructions:
Tool is designed to accept 5/16" and 1/2"
1.
wide coated and uncoated ties.
M50389
Multi-Lok Tool
Tension Adjustment Knob
Turn tension adjustment knob until
2.
desired tension setting is displayed in
tension indicator window. Space
between the numbers counts as one-half
setting. See step 7.
Extend handle open to release gripping
3.
mechanism and insert clamp tail into
tool through side load entry.
Squeeze handle repeatedly to tighten
4.
band around object. Be sure to release
handle completely to use full pull-up
stroke of tool. Buckle must be secure
against the tool head. Once the preset
tension has been reached, the handle
will no longer release completely.
To cut off excess clamp tail, squeeze
5.
handle one last time.
The tool must be reset by extending the
6.
handle out until it snaps into place. The
tool will now be ready to apply the next
clamp.
Tension Setting Range:
7.
Tension Indicator
Window
Handle
.270" (6.9mm) Multi-Lok 1 - 5 1/2
.470" (11.9mm) Multi-Lok 1 - 6 1/2
BAND-IT-IDEX, Inc.
A Unit of IDEX Corporation
4799 Dahlia Street
Denver, CO 80216-3070 USA
P: 1-800-525-0758
F: 1-800-624-3925
www. BAND-IT-IDEX.com
Page 1 of 5
Document # M50350 rev. F
Copyright
BAND-IT-IDEX, Inc. 2012
All rights reserved
Page 2
Repair Parts List
M50389
Multi-Lok Tool
(42)
4
37
(41,43)
(40)
36
16
6
(41)
35
38
13
15
14
12
11
(see next page for part
number tabulation)
27
x2
20
(42)
22
x2
28
8
(42)
39
(42)
x2
34
(41)
39
(42)
(41)
29
1
3
(41)
21
x4
7
10
9
19
x2
x2
31
32
26
(41)
24
5
x2
x2
(41)
2
(41)
18
2
25
30
(41)
33
17
23
BAND-IT-IDEX, Inc.
A Unit of IDEX Corporation
4799 Dahlia Street
Denver, CO 80216-3070 USA
P: 1-800-525-0758
F: 1-800-624-3925
www. BAND-IT-IDEX.com
Page 2 of 5
Document # M50350 rev. F
Copyright
BAND-IT-IDEX, Inc. 2012
All rights reserved
Page 3
Repair Parts Kit
M50389
Multi-Lok Tool
ITEM
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
PART
NUMBER
A02887
A73587
A84487
A85687
A91477
A91687
A91787
A91987
A92177
A92267
A92387
A92487
A92577
A93487
A93587
A94488
A94687
A94887
A94987
A95387
A95487
A96087
C09587
K57887
K83987
K84087
K93487
K93687
K93788
K93887
K94187
K94287
K94387
K97487
K97587
M50887
M53287
M53387
M54587
-
-
-
-
DESCRIPTION
SCREW, SET, #6-32 X .188 L
PIN, 5/32 DIA X .562 LONG
PIN, 1/8DIA X .50 LONG
SCREW, SET, #6-32 X .473 L
BODY PLATE, FRONT/SIDE LOAD TOOL
SPRING, DIE, 3.0L EXTRA HEAVY
SPRING, EXTENSION, 3/8 X 1.5" L
SCREW, FLAT, #6-32 X 1/4L
LINK, MIDDLE, CUTOFF
TENSION ARM, FRONT/SIDE LOAD TOOL
DECAL, TENSION INDICATOR
TENSION PLUNGER
TENSION CAP
BLOCK, TENSION
TENSION INDICATOR
SCREW, SET, #10-24 X 2.0 L
PIN, .125D X .19L
PIN, .188D X .78L
LINK, CUTOFF
TENSION PLATE
TENSION LINK
SCREW, FLAT, #6-32 X 3/4L
SPR, COMP, .12 DIA X .5L
PAD, CENTERING, TENSION ARM
BLADE, CUTOFF
KNIFE, CUTOFF, M503
BODY, LEFT, STANDARD
BODY, RIGHT, BLACK
PULL UP LEVER, SIDE LOAD
GRIPPER, PULLING
HEAD, SIDE LOAD
KNIFE COVER
GRIPPER, HOLDING
PIN, .125" DIA X .313" L
HANDLE, FRONT/SIDE LOAD TOOL
GRIP,TEXT .437ID X 3.25 LG, YELLOW
BEARING, THRUST, .250 ID X .462 OD
KNOB, ADJUSTMENT, .250 SHAFT
SCREW, CAP, #6-32 X .25 L
ADHESIVE, CYANOACRYLATE
GREASE, EXTREME PRESSURE
BLUE LOCTITE (MEDIUM STRENGTH)
RED LOCTITE (HIGH STRENGTH)
QTY
1
3
4
1
2
1
1
6
1
2
1
1
1
1
1
1
1
2
2
2
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
5
-
-
-
-
BAND-IT-IDEX, Inc.
A Unit of IDEX Corporation
4799 Dahlia Street
Denver, CO 80216-3070 USA
P: 1-800-525-0758
F: 1-800-624-3925
www. BAND-IT-IDEX.com
Page 3 of 5
Document # M50350 rev. F
Copyright
BAND-IT-IDEX, Inc. 2012
All rights reserved
Page 4
Blade Installation
Procedure
Tools Required:
Hex Keys: 1/16", 7/64"
Parts May Be Required:
Blade: K83987
Cap Screw: M54587
Set Screw: A02887
Special Instructions:
It is critical the knife and blade be assembled with a zero-gap to ensure
clean cut-off. Once correctly positioned, use threadlocking compound
to prevent parts from shifting during use (allow sufficient time for
compound to cure).
Installation Procedure:
Set the tool tension to -0-.
1.
Back-out cap screw (M54587) and set screw
2.
(A02887) - Figure 1.
Reposition/replace blade, but do not fully tighten
3.
screws yet.
Squeeze the handle completely and firmly strike the
4.
pull up lever against a non-metal surface to actuate
the knife - Figure 2 (note: you may also press firmly on
the pull up lever to actuate the knife - Figure 3).
M50389
Multi-Lok Tool
Figure 1
Figure 2
The knife is now in the downward position - Figure 4.
5.
BAND-IT-IDEX, Inc.
A Unit of IDEX Corporation
4799 Dahlia Street
Denver, CO 80216-3070 USA
P: 1-800-525-0758
F: 1-800-624-3925
Figure 3
www. BAND-IT-IDEX.com
Page 4 of 5
Figure 4
Document # M50350 rev. F
Copyright
BAND-IT-IDEX, Inc. 2012
All rights reserved
Page 5
Blade Installation
Procedure
Installation Procedure Continued:
Open the tension handle slightly so that the
6.
knife retracts from its full stroke; it should be
overlapping the blade edge - Figure 5.
Using the edge of a table or bench, force the
7.
pull up lever against the blade. This will force
the blade against the knife and ensure a zerogap - Figure 6.
Tighten the cap screw 1/2 turn past snug.
8.
M50389
Multi-Lok Tool
Figure 5
Tighten the set screw 1/2 turn past snug.
9.
Figure 6
BAND-IT-IDEX, Inc.
A Unit of IDEX Corporation
4799 Dahlia Street
Denver, CO 80216-3070 USA
P: 1-800-525-0758
F: 1-800-624-3925
www. BAND-IT-IDEX.com
Page 5 of 5
Document # M50350 rev. F
Copyright
BAND-IT-IDEX, Inc. 2012
All rights reserved
Loading...