BAND-IT J05069 User Manual

Operating
J05069
Instructions
Installing a Band-It Junior Clamp
Screw
Block
Setscrew
1 2
Place Heavy Duty Adapter on nose of BAND-IT Tool, posi­tioned as shown. Cut-off screw should not extend beyond bottom of screw block. Line up tool and adapter slots and tighten two setscrews. Insert BAND-IT Junior or Junior SID clamp tail into adapter nose through all slots and grip end with band gripper lever.
Cutoff Screw
Heavy Duty Adapter
Install clamp over hose assembly. Tension clamp by turning handle of BAND-IT Tool clockwise.
3 4
When properly tensioned, roll tool over hose, backing off tension handle ¼ to ½ turn only, through course of rollover, (depending on type and size of hose) until shear hook grips buckle edge. Tighten knurled nut by hand, securing buckle tightly between edge of hook and nose of adapter.
5
The finished BAND-IT Junior SID clamp lip lock will be bent upward 90° and have a cut-off edge (shown in green) that is flush to the edge of the buckle. Edges shown in red with hash marks are too high or too low and may result in lower lock strength or sharp edges.
BAND-IT-IDEX, Inc. A Unit of IDEX Corporation 4799 Dahlia Street Denver, CO 80216-0307 USA
www.BAND-IT-IDEX.com
Place ratchet wrench on hex nut. Operate wrench clockwise until clamp is sheared. Clamp is now locked and completed.
Document # P35387 rev. H
© Copyright
BAND-IT-IDEX, Inc. 2012
All rights reserved
Repair Parts
J05069
& Assembly
9
8
6
1
See Exploded View
7
3
5
2
Heavy Duty Adapter
14
* J93099 Exploded View
10
11
4
12
*NOTE: Replacement cutter blade kit design may vary.
Notes:
To assist in removing threaded parts, apply heat to soften locking compound.
When connecting item 9 (knob) or item 7 (nut) to item 8 (screw), clean threads (male and female) of foreign mat­ter, then apply one drop of medium strength locking com­pound (Loctite 242 or equivalent) onto male thread and connect parts together.
Periodically check item 10 (screw) for tension. Loosened screws may result in assembly breakage.
Operating Tip: Keep the bolts tight (8-14 ft-lbs.). A loose bolt may cause cracking or premature wear of the cutter blade and/or backing plate. This could result in improper clamp tensioning, locking, and cutting.
Operating Tip: Keep the leading edges of the cutter blade and backing plate free of metal shavings. Metal shavings will result in clamp tail gouging during tensioning. Clean
and hone the leading edges by hand. Do not use power tools. Honing should polish surfaces, not re­move material.
J050 Heavy Duty Adapter, Repair Parts List
Band-It
Part No.
J00587 1 Shear Hook (Design may vary) 1 J00987 2 Pin, Grooved 1
J05187
J06787 6 Screw Block 1
J06887
J93099
J11985 14 Ratchet Wrench 1 J01387 15 Hex Key, 3/16” (not shown) 1
Item # Description Qty.
3 Pin, Grooved 2
Body 1
4
Socket Head Screw 2
5
7
Hex Nut 1 Jr. Adapter Screw 1
8
Knob 1
9
10 Screw, Special 2 11 Backing Plate 1 12 Cutter Blade 1 13 Hex Key, 3/16” (not shown) 1
Refer to website for warranty information: http://www.band-it-idex.com/warranty.html
BAND-IT-IDEX, Inc. A Unit of IDEX Corporation 4799 Dahlia Street Denver, CO 80216-0307 USA
www.BAND-IT-IDEX.com
Document # P35387 rev. H
© Copyright
BAND-IT-IDEX, Inc. 2012
All rights reserved
Loading...