ROLZ-2
Portable AV/Conference Center
Assembly Instructions
1
Portable AV/Conference CenterRolz-2
Part Drawing Description Qty Part Drawing Description Qty
Hardware List
A 1 ½” Flat Head Screw 2 EA
P-1 Left Side Panel 1 EA
A1 2 ½” Flat Head Screw 2 EA
A2 Long Wood Screw 8 EA
P-2 Right Side Panel 1 EA
P-3 Back Panel 1 EA
P-4 Keyboard Shelf 1 EA
P-5 Fixed Shelf 1 EA
P-6 Removable shelf 1 EA
A3 Short Wood Screw 32 EA
A4 Short Wood Screw 8 EA
(Pan Head For Lock/catch)
B Keyboard Slide 2 EA
C Shelf Support Pins 4 EA
D 5” Wheel 2 EA
E Drawer Slide(Outer-left) 1 EA
F Drawer Slide(Outer-right) 1 EA
G Drawer Slide(Inner-left) 1 EA
H Drawer Slide(Inner-right) 1 EA
P-7 Top Platform 1 EA
P-8 Handle 1 EA
P-9 Bottom Panel 1 EA
K Cam Lock 26 EA
L Cam Post 26 EA
M Door Hinge 4 EA
N Big Allen Wrench 1 EA
N1 Small Allen Wrench 1 EA
2
Portable AV/Conference CenterRolz-2
Part Drawing Description Qty Part Drawing Description Qty
Hardware List
P Washer 16mm 6 EA
P-10 Door- Left 1 EA
R Glide 2 EA
P-11 Door - Right 1 EA
P-12 Threaded Axle 1 EA
P-13 Drawer Back 1 EA
P-14 Drawer Front 1 EA
P-15 Drawer Side 2 EA
S Washer 30mm 2 EA
T Door Catch 1 EA
U Door Lock 1 EA
V Key 2 EA
W Plastic Grommet 2 EA
X Drawer Knob 1 EA
Y Door Handle 2 EA
P-16 Drawer Bottom 1 EA
P-17 Slide Spacer 4 EA
Drawer Slide Detail
Insert Screw
in this hole.
Insert Screw
in this hole.
Z Screw 1 EA
(drawer knob)
Z1 Screw 4 EA
(door handle)
Keyboard Slide Detail
Insert Screw
in this hole.
3
Insert Screw
in this hole.
ROLZ-2 Assembly Diagram
To Assemble:
Identify and Separate all the Parts and Hardware.
1.
2.
Place the Left Side Panel (P-1) with the Predrilled
holes facing up. Attach 1 Slide Spacer (P-17), and 1
Keyboard Slide (B) to Left Side Panel (P-1) and
secure using 2 Wood Screws (A2) as shown in
illustration # 1.
(See Slide Detail on Page 3)
3.
Install 9 each Cam Posts (L) in the 9 threaded insert
nuts (Pre-installed) as shown in illustration # 1.
B
Illustration # 1
A2
P-1
4.
Install 1 Slide Spacers (P-17) and 1
Drawer Slide (E) to Left Side Panel (P-1)
and secure using 2 Wood Screws (A2)
[packaged with slides] as shown
in illustration # 1.
(See Detail on Page 3)
P-17
L
L
A2
E
Repeat Steps1 through 4 for the
5.
Right Side Panel (P-2).
P-17
4
6.
Place the Back Panel (P-3) with the Holes facing
up and install 6 each Cam Locks (K) into the
large holes (Pre-installed) as shown
in illustration # 2.
P-3
Phillips
Be sure that arrow on
top of Camlock (N)
aligns with centerline of
Edge Drilled hole.
K
Screwdriver
Arrow
Illustration # 3
P-7/P-5
NOTE: Hole is
closer to bottom of
Back Panel((P-3).
K
Centerline of
Edge Drilled
hole.
Illustration # 2
7.
Place the Top Platform (P-7)and
the Fixed Shelf (P-5) with the Predrilled Holes facing up and install
4 Cam Locks (K) into the 4 large
holes in each as shown
in illustration # 3.
Illustration # 4
P-9
R
8.
Place the Bottom Platform (P-9)
K
with the Pre-drilled Holes facing
up and install 4 each Cam Locks
(K) into the 4 large holes.
Install 2 each Glides (R) as shown
9.
in illustration # 4.
5
T o Secure Cam Locks, Insert Large
Phillips Head Screwdriver and turn Cam
Lock 1/4 turn (90 degrees) clockwise.
10.
Attach Side Panels (P-1 & P-2) to the Back
Panel (P-3) , the Top Plat form (P-7) the Fixed
Shelf (P-5), and the Bottom Panel (P-9) as
shown in illustration # 5. SECURE ONLY THE
9.
CAM LOCKS IN THE Bottom Panel and
those located at the bottom of the Back
Panel by turning the Cam Locks (L) 1/4” T urn
until they lock. Those CAM LOCKS at the top of
the Back Panel and in the top shelf should
remain loose until after handle is assembled.
Illustration # 5
P-1
P-7
P9
P-5
P-3
P-2
Missing Parts or UPS Damaged Parts
For Your Convenience you can
EMAIL us at
furniture@baltinc.com
24HOURS 7 DAYS A WEEK
6
11.
Attach Handle (P-8) to the Side Panels
(P-1 & P-2) using 2 each Screws (A) as
shown in illustration # 6. Tighten Screws
(A) using Small Allen Wrench (N1).
SECURE THE CAM LOCKS located at
the top of the Back Panel and in the top shelf
by turning Cam Locks (L) 1/4” T urn until they
lock.
P-2
A
P-8
Illustration # 6
P-1
P12
D
S
A1
P
P
A
Install 2 Wheels (D) on either side of the unit using 2
12.
each Long Screw (A1), 6 each Washers (P), 2 each
Washers (S) and secure using 1 Threaded Axle (P-12)
and Big Allen W rench (N) as shown in illustration # 6.
Squeeze Plastic Clip as shown by arrows in illustration
13A.
# 7A to release inner keyboard slide
(Squeeze up on the left side/down on the right side).
A3
B
Illustration # 7B
P-4
A3
B
A1
D
A3
Illustration # 7A
FRONT of Slide
Insert Screw
in this hole.
Plastic Clip
BACK of Slide
Insert Screw
in this hole.
Attach Keyboard Shelf (P-4) to the
13B.
Keyboard Slides (B) using 4 each
screws (A3) as shown in
illustration # 7B.
[Slide Keyboard Shelf Assembly
back into the Keyboard Slides.]
7
Attach Left Door (P-10) to the Left Side
14.
Panel (P-1) using 2 each Door Hinges (M)
and 12 each Short Wood Screws (A3) as
shown in illustration #8.
Illustration # 8
P-1
M
A3
Attach Door Catch
15.
(T) to Left Door (P-10)
using 4 each Short Wood
Screws (A4) as shown in
illustration # 8.
Attach Right Door (P-1 1) to the Right Side
17.
Panel (P-2) using 2 each Door Hinges (M)
and 12 each Short Wood Screws (A3) as
shown in illustration # 9.
18.
Attach Door Lock (U) to Right Door (P-1 1)
using 4 each Short Wood Screws (A4) as
shown in illustration # 9.
T
Z1
A4
P-10
Y
Attach Door Handle (Y) to Left
16.
Door (P-10) using 2 screw (Z1).
P-2
P-11
19.
Attach Door Handle (Y) to Right Door
(P-1 1) using 2 screws (Z1).
Z1
M
A3
A4
U
Y
Illustration # 9
8
20.
Place the 2 Drawer Sides (P-15) with the
Holes facing up and install 4 each Cam
Locks (K) into the large holes
(Pre-installed) in each side
as shown in illustration # 10.
21.
Place the Drawer Back and Front (P-13 &
P-14) with the Predrilled holes facing up
and install 4 each Cam Posts (L) in the 4
threaded insert nuts (Pre-installed) as
shown in illustration # 11.
Illustration # 11
P-13
L
Illustration # 10
K
K
Attach the Drawer Back (P-13) to the
22
L
Drawer Sides (P-15) and secure by
P-15
K
turning the Cam Locks (K) 1/4 T urn until
L
they lock. as shown in illustration # 12.
23.
Slide the Drawer Bottom ( P-16) into
the slot as shown in illustration # 12.
P-13
Do not use unless all screws
are tight. At least every six
months, check all screws
to be sure they are tight.
If parts are missing, broken,
damaged, or worn, stop use
of the product until repairs
are made by your dealer using
factory authorised parts.
P-15
Should you require assistance during assembly,
please call our Customer Service Department
Monday - Friday 8 a.m. - 5 p.m. Central Standard Time
P-16
P-15
Illustration # 12
Toll-Free Customer Service
1-800-749-2258
9
Attach the Drawer Front (P-14) to the
24.
Drawer Sides (P-15) and secure by
turning the Cam Locks (L) 1/4 Turn until
they lock. as shown in illustration # 13.
25.
Attach Drawer Knob (X) to Drawer Front
(P-14) using 1 screw (Z).
Illustration # 13
P-15
P-14
X
Z
Illustration # 14
A3
G
P-15
A3
P-15
W
H
Attach the Left and Right Drawer
26.
Slides (G & H) to the Drawer Sides
(P-15) and secure using 4 each screws
(A3) as shown in illustration # 14.
P-7
P-1
C
W
27.
Place 2 Shelf Support Pins (C)
in each of the two Side Panels
(P-1 & P-2 ) at desired shelf
height. Place Removable Shelf
(P-6) on four Shelf Support Pins.
Insert Drawer Assembly in Drawer
28.
Slides ( E & F) as shown in
illustration # 15.
Insert Plastic Grommet (W) into the hole
29.
in the Top Shelf (P-7) and the Back
Panel (P-3) as shown in
illustrations # 15A and 15B.
Illustration # 15A
P-6
Drawer
Assembly
E&F
P-2
Illustration # 15B
ROLZ - 04/28/04
10
Rolz-2
Portable A V/Conference Center
19-¾ X 15
4 ½
For more information
1-800-749-2258
44
Shipping Information
4.2 Cubic Feet
92 lbs
.
9 ¼
12 ¼
16 ¼
39 ½
22
21¼
15¾
24”
50”
6”
ROLZ - 04/28/04
11
Loading...