Balt 89843, LX-48B Assembly Instructions Manual

Download

123456789012345678901234567890121234567890123456789012345678901212345678901234

Single Student Training Table

Assembly Instructions

#89843 LX-48B

W/Locking CPU Door

#89843 LX-48B Single Student Training Table W/ Locking CPU Door

Part Drawing Description Qty

P-1 Left Side Panel 1 EA

P-2 Right Side Panel 1 EA

P-3 Bottom Panel 1 EA

P-4 Table Top 1 EA

P-5 Top Support 2 EA

Hardware List

A Socket Screw M6X28mm 4 EA

A1 Philips Screw M6X12mm 2 EA

A2 Philips Screw M6X25mm 4 EA

A3 Phil Screw M4x6mm 4 EA

A4 CS Phil Screw M4X10mm 1 EA

(CSHead For Strike Plate)

A5 CS Phil Screw M4X12mm 10 EA

(CSHead For CPU Hinge)

A6 Phil Wd Screw M4x25 1 EA

(Door Knob)

A7 Phil Screw (Magnet) 2 EA

A8 ¼” Phil Head Lock Screw 1 EA

P-6 Top Front Brace 1 EA

P-7 Bottom Front Brace 1 EA

P-8 Metal Back Panel 1 EA

P-9 Upper Leg Mount 1 EA

P-10 Lower Leg Mount 1 EA

P-1 1 Leg Upright 1 EA

P-12 Metal Panel 1 EA

A9 Socket Screw M6X9mm 4 EA

B Wood Screw 2 1/4” 4 EA

B1 Black Wood Screw 1/2” 2 EA

B2 Silver Wood Screw 1/2” 12 EA

C Cam Lock 8 EA

D Cam Post 8 EA

E 1” Wood Dowel 20 EA

F Leveling Glide 2 EA

F1 Glide 4 EA

G Lock Cylinder 1 EA

H Lock Retainer 1 EA

P-13 Plastic Keyboard Tray 1 EA

Tools required: Phillips Head Screwdriver/Hammer

J Lock Plate 1 EA

K Magnet 1 EA

K1 Strike Plate 1 EA

#89843

LX-48B Workstation

Part Drawing Description Qty

P-14 Keyboard Bracket 4 EA

P-15 Keyboard Slide 2 EA

P-16 CPU Door 1 EA

T ools required:

Phillips Head Screwdriver Standard Flat Head Screwdriver

Hardware List

L Lock Washer 1 EA

M Lock Hex 1 EA

N Key 2 EA

P Door Knob 1 EA

R Hinge 2 EA

S Grommet Sleeve 2 EA

T Grommet Cap 2 EA

V Allen Wrench 1 EA

#89843-B LX-48

Assembly Diagram

P-9

Note: 4 Holes are located near

Upper Leg Mount (P-9) as shown in illustration # 1

To Assemble:

Identify and Separate all the Parts and Hardware.

Place Leg Upright (P-1 1) on a flat surface as shown in

illustration # 1.[ with 2 large holes facing up ]

Attach Upper Leg Mount (P-9) and Lower Leg Mount (P-10) using 4 each Phillips Screws (A2) as shown in illustration # 1.

P-11

Illustration # 1

P-10

Place the Left Side Panel (P-1) with the Predrilled holes facing up and install 2 Cam Posts (D)

in the 2 threaded insert nuts (Pre-installed) as shown in illustration # 2. Install 2 Cam Locks (C) in the 2 large holes.

Install 8 Wood Dowels (E) into the holes as shown in illustration # 2.

Attach Magnet (K) using 2 Screws (A7).

Phillips Screwdriver

Arrow

P-1

Be sure that arrow on top of Camlock (C) aligns with centerline of Edge Drilled hole.

Centerline of Edge Drilled hole.

Note: Camlocks can be turned with Allen W rench,

or Large Phillips Screwdriver

Illustration # 2

P-1

Place the Right Side Panel (P-2) with the Predrilled

8. holes facing up and install 2 each Cam Posts (D) in

P-2

the 2 threaded insert nuts (Pre-installed) as shown in illustration # 3.

Install 2 each Cam Locks (C) in the 2 large holes.

10.

Install 8 Wood Dowels (E) into the holes as shown in illustration # 3.

Do not use unless all screws are tight. At least every six months, check all screws to be

sure they are tight. If parts are missing, broken, damaged, or worn, stop use

of the product until repairs are made by your dealer using factory authorized parts.

Illustration # 3

Place the Bottom Panel (P-3) with the Pre-

1 1.

drilled holes facing up and install 4 Cam Locks (C) in the 4 large holes as shown in illustration # 4.

P-3

Attach 2 Hinges (R) to the

12.

CPU Door (P-16) using 6 Screws (A5) as shown in illustation #5.

Illustration # 4

Be sure that arrow on top of Camlock (C) aligns with centerline of Edge Drilled hole.

Phillips Screwdriver

Arrow

P-1

Attach Door Knob (P) to CPU

13.

Door (P-16) using 1 screw (A6). Attach S trike Plate (K1) to CPU

14.

Door (P-16) using 1 screw (A4).

Illustration # 5

P-16

Centerline of Edge Drilled hole.

Illustration # 5A

15.

Insert 1 each Lock Cylinder(G) through the Lock Plate (J) and the hole in the CPU Door (P-16). Secure Lock Cylinder (G) using the Lock Washer (L) and the Lock Hex (M). (FINGER TIGHTEN ONL Y.)

16.

Slide Lock Retainer (H) over the square end of Lock Cylinder (G). Secure using the ¼” Phil Head Lock Screw (A8). Before tightening the Lock Hex (M), Insert the Key (N) and turn lock. Be sure lock is aligned with Key slot as shown in Illustration #5A.

TIGHTEN LOCK HEX (M)

Door

Front view

Locked Position

Slide Bottom Panel (P-3) over the Wood Dowels (E) and

17.

the Camposts (D) in the Right Side Panel (P-2) as shown in illustration #6. Secure by turning the Cam Locks (C) 1/4 turn until they lock.

P-5

Slide 2 Top Supports (P-5)

18.

and 1 Bottom Front Brace (P-7) over the Wood Dowels (E) in the Right Side Panel (P-2).

17.

To Secure Cam Locks, Insert Large Phillips Head Screwdriver and turn Cam Lock 1/4 turn (90 degrees) clockwise.

P-3

P-2

P-7

Illustration # 6

P-7

P-2

P-3

P-6

P-5

P-1

Attach Left Side Panel (P-1)

19. to Bottom Panel (P-3), Top Support (P-5), and Bottom Front Brace(P-7) as shown in illustration # 7.

20.

Secure by turning the Cam Locks (C) 1/4 turn until they lock.

Insert the T op Front Brace

21. (P-6) Between Left Side Panel (P-1), and Right Side Panel (P-2). Secure using 4 Screws (B) as shown in illustration #7.

Illustration # 7

Attach Back Panel (P-8) to the

22. Left & Right Side Panels (P-1 & P-2) using 4

Screws (A9) as shown in illustration # 8.

Place the T able T op (P-4) with the Predrilled

23. holes facing up and install 4 each Cam Posts

(D) in the 4 threaded insert nuts (Pre-installed) as shown in illustration # 9.

Install 4 Wood Dowels (E) into the 4 holes in

24. the T able T op (P-4).

Slide Wood CPU Assembly over the Wood

25. Dowels (E) and the Camposts (D) in the Table

T op (P-4) as shown in illustration # 9. T urn the Cam Locks (C) 1/4 turn until they lock.

Secure Wood CPU Assembly to the

26. T able T op (P-4) using 2 screws (A).

Illustration # 8

P-1

P-8

P-2

Attach Upper Leg Mount (P-9) to the Table T op (P-4) using 2 Screws (A) as shown in

27.

illustrations # 9. Tighten Screws using Allen Wrench (V).

To Secure Cam Locks, Insert Large Phillips Head Screwdriver and turn Cam Lock 1/4 turn (90 degrees) clockwise.

Install 2 Leveling Glide (F) in the bottom of the Lower Leg Mount (P-10) .

P-2

P-1

Wood CPU

Assembly

P-4

Illustration # 9

P-10

Use a hammer to install 4 Plastic Glides (F1) in the bottom of Left

29. Side Panel (P-1) and Right Side Panel (P-2) as shown in illustration #9.

P-9

Attach 2 Keyboard Brackets

30. (P-14) to 1 Keyboard Slide

(P-15) using 2 Screws (A3) as

shown in illustrations # 10.

31.

Attach 2 Keyboard Brackets (P-14`) to 2nd Keyboard Slide (P-15) using 2 Screws (A3).

Illustration # 10

P-15

Note: The 2 Slides will have Brackets on the opposite sides.

Attach 2 Keyboard Slides (P-15) to

32. the Plastic Keyboard Tray (P-13) using 4 Screws (B2) as shown in

illustrations # 1 1.

P-15

P-14

Should you require assistance during assembly,

please call our Customer Service Department

Monday - Friday 8 a.m. - 5 p.m.

Central Standard Time

P-14

Toll-Free Customer Service

1-800-749-2258

Illustration #11

P-13

P-15

P-1

Illustration #12

Attach Keyboard Drawer to

33. the Table T op (P-4) using 8

Screws (B2) as shown in

illustrations # 12.

Insert 1 Grommet Sleeve (S) in Round opening in the

34. Left Side Panel (P-1) as shown in illustrations #12.

35.

Snap 1 Grommet Cap (T) into Grommet Sleeves (S) .

P-13

P-4

36.

Attach Metal Panel (P-12) to the Left Leg Assembly using 2 Phillips Screws (A1) as shown in illustrations # 13.

Illustration#13

37.

Attach Metal Panel (P-12) to the Wood CPU Assembly using 2 Wood Screws (B1) as shown in illustrations # 13.

Wood CPU

Assembly

P-12

38.

Insert 1 Grommet Sleeve (S) in Round opening in T able T op (P-4) as shown in illustration #14.

39.

Snap Grommet Cap (T) into Grommet Sleeve (S).

40.

Align CPU Door (P-16) With the Right Side Panel (P-2) as shown in illustration #14.

41.

Secure Door Hinges (R) to the Right Side Panel (P-2) using 4 each Wood Screws (A5).

Illustration #14

P-2

P-16

The Balt product you have purchased is guaranteed against material and workmanship defects. This guarantee extends 1 year from date of purchase. Should this product fail to function satisfactorily under normal use due to defect or imperfection, the defective part or product will be replaced. Damage caused by common carriers during shipment is not included in this guarantee.

This guarantee sets forth all applicable guarantees and remedies. No other warranty , expressed or

implied shall apply . Failure to follow instructions found in Important Information Section of Owner Sheet shall void the guarantee. Consequential or incidental damages and or costs are not refundable.

Important

89843B - 07/20/07

Balt 89843, LX-48B Assembly Instructions Manual

Specifications and Main Features

Frequently Asked Questions

User Manual