LX-72
2 Student Training Table
w/Locking CPU Doors
Assembly Instructions
1
LX-72 2 Student Training Table
Part Drawing Description Qty
P-1 Left Side Panel 1 EA
P-2 Right Side Panel 1 EA
P-3 Bottom Panel 1 EA
P-4 Divider Panel 1 EA
P-5 Top Support 4 EA
P-6 Top Front Brace 2 EA
P-7 Bottom Front Brace 1 EA
Part Drawing Description Qty
Hardware List
A Socket Screw M6X28mm 8 EA
A1 Philips Screw M6X12mm 4 EA
A2 Philips Screw M6X25mm 8 EA
A3 Phil Screw M4x6mm 4 EA
A4 CS Phil Screw M4X10mm 2 EA
(CSHead For Strike Plate)
A5 CS Phil Screw M4X12mm 20 EA
(CSHead For CPU Hinge)
A6 Phil Wd Screw M4x25 2 EA
(Door Knob)
A7 Phil Screw (Magnet) 4 EA
A8 ¼” Phil Head Lock Screw 2 EA
P-8 Metal CPU Panel 1 EA
P-9 Upper Leg Mount 2 EA
P-10 Lower Leg Mount 2 EA
P-1 1 Leg Upright 2 EA
P-12 Metal Panel 2 EA
P-13 Table Top 1 EA
A9 Socket Screw M6X9mm 4 EA
B Wood Screw 2 1/4” 6 EA
B1 Black Wood Screw 1/2” 4 EA
B2 Silver Wood Screw 1/2” 20 EA
C Cam Lock 10 EA
D Cam Post 10 EA
E 1” Wood Dowel 22 EA
E1 2” Wood Dowel 6 EA
F Leveling Glide 4 EA
F1 Glide 4 EA
G Lock Cylinder 2 EA
Tools required: Phillips Head Screwdriver/Hammer
H Lock Retainer 2 EA
2
LX-72Workstation
Part Drawing Description Qty
P-14 Plastic Keyboard Tray 2 EA
P-15 Keyboard Slide 4 EA
P-16 Keyboard Bracket 4 EA
P-17 Left CPU Door 1 EA
P-18 Right CPU Door 1 EA
T ools required:
Phillips Head Screwdriver
Standard Flat Head Screwdriver
Hardware List
J Lock Plate 2 EA
K Magnet 2 EA
K1 Strike Plate 2 EA
L Lock Washer 2 EA
M Lock Hex 2 EA
N Key 4 EA
P Door Knob 2 EA
R Hinge 4 EA
S Grommet Sleeve 4 EA
T Grommet Cap 4 EA
V Allen Wrench 1 EA
Should you require assistance during assembly,
please call our Customer Service Department
Monday - Friday 8 a.m. - 5 p.m.
Central Standard Time
Toll-Free Customer Service
1-800-749-2258
Do not use unless all screws are tight. At least every six months, check all screws to be
sure they are tight. If parts are missing, broken, damaged, or worn, stop use
of the product until repairs are made by your dealer using factory authorized parts.
3
LX-72
Assembly Diagram
Note: On both Legs, 4 Holes
located near Upper Leg Mount
(P-8) as shown in illustration # 1a &1b.
A2
P-9
P-11
Illustration # 1a
P-9
A2
P-11
P-10
A2
To Assemble:
1.
Identify and Separate all the Parts and Hardware.
Place 2 Leg Uprights (P-1 1) on a flat surface
2.
as shown in illustration # 1a.
[one with 2 large holes facing up,
one with 2 large holes facing down]
Attach 2 Upper Leg Mounts (P-9) and 2 Lower Leg Mounts (P-10)
3.
using 8 each Phillips Screws (A2) as shown in illustration # 1.
Left Leg Assembly
P-10
Right Leg Assembly
P-9
P-11
P-10
Illustration # 1b
4
Note: Camlocks can be turned with Allen W rench, or Large Phillips Screwdriver
4.
Place the Left Side Panel (P-1) with the Predrilled
holes facing up and install 2 Cam Posts (D) in the 2
threaded insert nuts (Pre-installed) as shown
in illustration # 2.
E
5.
Install 2 Cam Locks (C) in the 2 large holes.
Illustration # 2
Install 8 Wood Dowels (E) into
6.
the holes as shown in illustration # 2.
C
P-2
E
D
Illustration # 3
P-4
D
C
E
Place the Right Side Panel (P-2)
7.
E
P-1
with the Predrilled holes facing up
and install 2 each Cam Posts (D) in
the 2 threaded insert nuts (Preinstalled) as shown in illustration # 3.
8.
Install 2 each Cam Locks (C) in the 2 large holes.
Install 8 Wood Dowels (E) into the holes as shown in
9.
illustration # 3.
E1
C
E1
Illustration # 4
A7
Place the Divider Panel (P-4) with the Pre-drilled holes facing up and
10.
K
A7
K
install 2 Cam Locks (C) in the 2 large holes as shown in illustration # 4.
11.
Slide 6 Wood Dowels (E1) Through 4 holes until they protrude the same
on both sides.
Attach 2 Magnets (K) using 4 Screws (A7) as shown in illustration # 4.
12.
5
Be sure that arrow on
top of Camlock (C)
aligns with centerline of
Edge Drilled hole.
Phillips
Screwdriver
Arrow
P-1
Centerline of
Edge Drilled
hole.
Place the Bottom Panel (P-3)
13.
with the Pre-drilled holes facing
up and install 4 Cam Locks (C)
in the 4 large holes as
shown in illustration # 5.
14.
Attach 2 Hinges (R) to the
Left CPU Door (P-17) using 6 Screws
(A5) as shown in illustation #5.
P-3
C
Illustration # 5
Be sure that arrow on
top of Camlock (C)
aligns with centerline of
Edge Drilled hole.
Phillips
Screwdriver
15.
Attach 1 Door Knob (P) to Left CPU
Door (P-17) using 1 screw (A6).
Attach S trike Plate (K1) to Left CPU
16.
Door (P-17) using 1 screw (A4).
A4
K1
A8
H
A6
R
M
Arrow
A5
L
J
A5
P-1
P-17
A5
Centerline of
Edge Drilled
hole.
R
P-18
Illustration # 5
17.
Insert 1 each Lock Cylinder(G) through the Lock
P
G
Plate (J) and the hole in the CPU Door (P-17).
Secure Lock Cylinder (G) using the Lock Washer (L) and the Lock
Hex (M). (FINGER TIGHTEN ONL Y.)
18.
Slide Lock Retainer (H) over the square end of Lock Cylinder (G).
Secure using the ¼” Phil Head Lock Screw (A8). Before tightening
the Lock Hex (M), Insert the Key (N) and turn lock. Be sure lock is
aligned with Key slot as shown in Illustration #5A.
TIGHTEN LOCK HEX (M)
19.
Repeat Steps 14-18 for Right CPU Door (P-18).
6
H
Illustration # 5A
G
Door
Front view
Locked Position
Illustration # 6
P-5
E
P-5
P-3
To Secure Cam
Locks, Insert
Large Phillips
P-2
C
Head Screwdriver and turn
E
Cam Lock 1/4
turn (90 degrees)
clockwise.
20.
Slide Bottom Panel (P-3) over the Wood Dowels (E) and the Camposts (D) in the Right
Side Panel (P-2) as shown in illustration #6. Secure by turning the Cam Locks (C)
1/4 turn until they lock.
Slide 2 Top Supports (P-5) over the Wood Dowels (E) in the Right Side Panel (P-2).
21.
22.
Slide 2 Top Front Braces (P-6)
over the Wood Dowels (E1) in
B
P-3
P-4
the Divider Panel (P-4) as
shown in illustration #7.
D
P-5
P-5
B
23.
Slide 4 Dowels (E1) in Divider
Panel (P-4) into the end of 2
T op Supports (P-5) as shown
in illustration #7.
Secure Divider Panel (P-4)
24.
to Bottom Panel (P-3) using
2 Wood Screws (B) as
shown in illustration # 7.
Slide 2 Top Supports (P-5) over the Wood
25.
Dowels (E1) in the Divider Panel (P-4).
26.
Secure T op Front Brace (P-6) to Right Side
Panel (P-2) using 2 Wood Screws (B) as
shown in illustration # 7.
P-2
P-6
E1
E1
P-6
P-5
B
Illustration # 7
7
P-5
Slide Bottom Front Brace (P-7)
27.
over the Wood Dowels (E) in the
Right Side Panel (P-2) as shown
in illustration #8.
Attach Left Side Panel (P-1) to
28.
Bottom Panel (P-3), T op Support
(P-5), and Bottom Front Brace
(P-7) as shown in illustration # 8.
29.
Secure by turning the Cam Locks
(C) 1/4 turn until they lock.
P-1
P-3
Illustration # 8
B
P-6
P-5
P-5
E
Secure T op Front Brace (P-6) to
Left Side Panel (P-1) using 2
Wood Screws (B) as shown in
illustration # 8.
Illustration # 9
A9
P-2
P-2
A9
P-7
E
30.
Attach Metal CPU Panel (P-8) to the
Left Side Panel (P-1) and the Right
Side Panel (P-2) using 4 Screws
(A9) as shown in illustration #9.
P-1
P-8
A9
T o Secure Cam
Locks, Insert Large
Phillips Head
Screwdriver and
turn Cam Lock 1/4
turn (90 degrees)
clockwise.
8
Place the Table T op (P-13) with the Predrilled holes facing up and install 6 each Cam Posts (D)
31.
in the 6 threaded insert nuts (Pre-installed) as shown in illustration # 10.
32.
Install 6 Wood Dowels (E) into the 6 holes as shown in illustration # 10.
33.
Slide Wood CPU Assembly over the Wood Dowels (E) and the Camposts (D) in the Table T op
(P-13) as shown in illustration #10. Turn the Cam Locks (C) 1/4 turn until they lock.
34.
Secure Wood CPU Assembly to the Table T op (P-13) using 4 screws (A).
Attach 2 Upper Leg Mounts (P-9) to the Top Panel (P-13) using 4 each Socket Screws (A) as
35.
shown in illustrations # 10. Tighten Screws using Allen Wrench (V).
P-10
P-9
F
A
P-13
D
Illustration # 10
P-10
F
A
A
A
E
E
D
A
P-15
P-16
Illustration # 11
A3
P-15
P-16
P-16
9
A3
Install 4 Leveling Glide (F) in
36.
the bottom of the Lower Leg
Mounts (P-10) as shown in
illustration #10.
Attach 2 Keyboard Brackets
37.
(P-16) to 1 Keyboard Slide
(P-15) using 2 Screws (A3) as
shown in illustrations # 1 1.
38.
Attach 2 Keyboard Brackets
(P-16) to 1 Keyboard Slide (P-
15) using 2 Screws (A3).
Note: The 2 Slides will have
Brackets are on the opposite sides.
Illustration#12
39.
Attach 1 Keyboard Slide w/
brackets and 1 Keyboard
slide (P-15)to each of the 2
B2
Plastic Keyboard Trays
(P-14) using 4 Screws (B2)
as shown in
illustrations # 12.
40.
Attach Right Keyboard Drawer to the Table
T op (P-13) and the W ood CPU Assembly
using 6 Screws (B2) as shown in
illustration # 13.
Attach Left Keyboard Drawer to the Table
41.
T op (P-13) and the W ood CPU Assembly
using 6 Screws (B2) as shown in
illustrations # 14.
P-15
P-14
Right Keyboard
Drawer
T
P-13
B2
P-14
B2
Drawer
Left Keyboard
S
P-2
B2
P-15
Keyboard Slide
w/brackets
Right Keyboard
Drawer
B2
Left Keyboard
Drawer
Illustration#14
B2
B2
P-1
S
T
42.
Insert 2 Grommet Sleeves (S)
Illustration#13
in Round openings in the Left
P-13
B2
Side Panel (P-1) and the Right
Side Panel (P-2) as shown in
illustrations #13 & 14.
43.
Snap 2 Grommet Caps (T) into
Grommet Sleeves (S) .
10
P-12
A1
B1
F1
B1
P-1
Illustration#15
F1
P-2
A1
P-12
Attach 1 Metal Panel (P-12) to the Left Leg Assembly and 1 Metal Panel (P-12) to the Right
44.
Leg Assembly using 4 Phillips Screws (A1) as shown in illustrations #15.
Attach 2 Metal Panels (P-12) to the Wood CPU Assembly using 4 Wood Screws (B1) as
45.
shown in illustrations #15.
46.
Use a hammer to install 4 Plastic Glides (F1) in the bottom of Left Side Panel (P-1) and Right
Side Panel (P-2) as shown in illustration #15.
Important
The Balt product you have purchased is guaranteed against material and workmanship defects. This
guarantee extends 1 year from date of purchase. Should this product fail to function satisfactorily under normal
use due to defect or imperfection, the defective part or product will be replaced. Damage caused by common
carriers during shipment is not included in this guarantee.
This guarantee sets forth all applicable guarantees and remedies. No other warranty , expressed or
implied shall apply . Failure to follow instructions found in Important Information Section of Owner
Sheet shall void the guarantee. Consequential or incidental damages and or costs are not refundable.
11
41.
Insert 1 Grommet Sleeve (S) in Round opening in T able T op (P-13) as shown in illustration #16.
Snap Grommet Cap (T) into Grommet Sleeve (S).
42.
Align Left CPU Door (P-17) With the Left Side Panel (P-1) as shown in illustration #16.
43.
Secure Door Hinges (R) to the Left Side Panel (P-1) using 4 each Wood Screws (A5).
44.
Align Right CPU Door (P-18) With the Right Side Panel (P-2) as shown in illustration #16.
45.
46.
Secure Door Hinges (R) to the Right Side Panel (P-2) using 4 each Wood Screws (A5).
Illustration#16
P-13
T
T
S
P-1
R
S
P-2
P-17
P-18
A5
A5
R
12
LX-72_2-17-11
Loading...