Page 1
T ools Needed: Only Required for Doors Without Cutout
Exploded View Patio Function Deadbolt
Parts Enclosed:
If your door is not pre-bored, see instructions for door preparation.
1. Pencil
2. 1-5/8" diameter hole saw
3. 1/2" or 3/4" wood chisel
4. Drill and assorted bits: 1/8", 5/32" and 1"
5. No. 2 and No. 3 phillips screwdrivers
6. Measuring device
7. Flathead Screwdriver
Patio Deadbolt Installation
1. 2 each #8 - 32 Oval Head Machine Screw
2. 1 Turnpiece Trim
3. 3 each #6 x3/4” Flat Head Sheet Metal Screw
4. 1 Turnpiece Mounting Plate
5. 1 Adjustable Backset Deadbolt
6. 2 each #8 x 3/4” Flathead Combination Screws
7. 1 Tailpiece (Not Shown)
1.
2.
3.
4.
5.
6.
Note: See Strike Installation section for strike parts listing.
Installing Deadbolt
Strike Installation
Close door and extend deadbolt several times
against door frame. Strike centering indicator
will leave a center mark on the door frame.
(fig. 4)
HINT : Applying lipstick or graphite to end
of deadbolt will leave an easy to read
mark on frame.
1
8
2 4
Chisel out the area marked for the faceplate to a depth of 5/32" or until faceplate
is flush with door edge.
3
Insert deadbolt into edge of door while holding
faceplate.T race the outline of the faceplate onto
thedooredge.Mark screwholecenters and drill
with a 1/8”drill.
The patio deadbolt is installed on the inside
ONL
Y of the door . NOTE:DO NOT DRILL
COMPLETEL Y THROUGH DOOR.
9
Position strike plate on center mark. Align and
trace outside of strike and mounting screws onto
the door frame. (fig. 5)
Top view of door
Template
Facebore
Edgebore
Bolthead
Centering
indicator
A
A
B
B
T o position template fold enclosed template on line and locate on door at specified height (about 40” from the floor). If you have a new door that is not already
cut-out, please follow these instructions. If your door is pre-bored please proceed to Installation-Step 5. Place the folded edge on turnpiece side of door as
shown in the illustration. Determine door thickness and backset (2-3/8" or 23/4"). Mark the door for face and edge bores.
NOTE: IF YOUR DOOR HAS BEEN DRILLED FOR THE BALDWIN
PATIO DEADBOLT. SKIP TO STEP #5
Door Preparation
fig.4
fig. 5
Side of Door
with Trim
NOTE: Make
sure tip of drill
bit does NOT go
through door
Measure twice , drill once.
5
b. Insert deadbolt into edge of door . Install with two #8 x 3/4" flat head
combination screws provided (see diagram for proper positioning). Ensure
bolthead is extended throughout installation procedure.
a.The deadbolt supplied with this
unit has an adjustable backset feature. It will be set at 2-3/8" backset.
T o adjust to 2-3/4" backset, grasp
body and twist faceplate/bolthead
assembly 180°until it stops. Unit is
now ready for installation in a 2-3/4"
backset configuration.
INSIDE
Install deadbolt with both long slots on latch
body in upper position.
Door Thickness
1-3/8” 1-3/16”
1-3/4” 1-3/8”
2” 1-1/2”
2-1/4” 1-5/8”
Assembly
7
Insert tailpiece (packed in plastic bag) into slot on the back side of turnpiece trim. (fig2) Place turnpiece trim over mounting plate keeping tailpiece vertical. Insert tailpiece into deadbolt. Attach trim to mounting
plate with two #8-32 x 5/8" oval head machine screws (fig 3).
Proceed to Strike Installation.
6
INSIDE
Turnpiece trim
Slot
Tailpiece
fig. 2
Mounting plate
Turnpiece trim
fig. 3
Facebore
Drill Depth - A.
Latch Backset
2-3/8” 3-1/2”
2-3/4” 3-7/8”
Edgebore
Drill Depth - B.
fig.1
“TOP”
Install the mounting plate to the door
with the center recess loacated in the
1-5/8” hole. Make sure that stamped
“T op” (fig. 1) is located at the top. Fasten
mounting plate with 3 #6 x 3/4” Flat
Head Sheet Metal Screws.
Page 2
PK-1141 (4/98)
Patio Deadb ol t
I nstallation Instruct ions
BALDWIN
®
.
B
a
l
d
w
i
n
.
G
u
a
r
a
n
t
e
e
d
F
o
r
L
i
f
e
.
PK-1141
©Baldwin Hardware Corporation
P.O. Box 15048 Reading, PA 19612
Installing Deadbolt
Remember Baldwin
With the completion of your project, remember that Baldwin quality hardware and
giftware products are available for all your decorating and remodeling needs.
Matching knob and leversets for interior doors, beautiful bath accessories, and a
complete selection of cabinet and door enhancing hardware are all available from
your Baldwin retailer.
With your purchase of The Images Collection solid brass patio deadbolt,
you’re among a group of discerning individuals who know the value of
selecting the finest – Baldwin.
Images entrance locksets, interior latchsets, and deadbolts coordinate
beautifully, enabling you to carry a specific design theme throughout your
home.
Our step-by-step installation instructions will help guide you through your
project quickly and easily.
Before you begin your installation, read and understand the installation
instructions and marking templates. If you have any questions, please do
not hesitate to contact our Baldwin T echnical Services Department,
1-800-566-1986. We’re here to help!
Technical Services Support
1-800-566-1986
Hours: 6 am to Midnight C.S.T.-7days a week.
Congratulations!
Patio Deadbolt Installation
12
Install strike as illustrated.
1. Dust Box
2. Reinforcing Strike
3. #8 x 3/4" Combination Screws (2)
4. 3" Reinforcing Screws* (2)
5. Strike Plate
6. #8-32 x 1/4" Machine Screws (2)
*Note:
Lubricant recommended
when installing 3" reinforcing
screws.
1
2
4*
6
5
3
Strike Installation (continued)
Using reinforcing strike as a
template, mark locations for
reinforcing screws. (fig 6)
Drill two 5/32" dia. pilot holes
for the 3" long screws and
two 1/8" dia. pilot holes for
the #8 x 3/4" screws. Mark
drill points 5/16" above and
below center line. Bore two 1"
dia. holes 1-1/4" deep at
these points. Chisel out holes
for dust box. (fig. 7)
10
Mortise 7/32" deep or until the strike
box, reinforcing strike and strike plate fits
inside mortise and flush with the door
frame. (fig. 8)
11
Bore 1" dia. hole
above and below
centering point.
Drill 1/8" dia. pilot
holes for # 8 screws.
Drill 5/32" dia. pilot
holes for 3" screws.
5/16"
above
center
point.
5/16" below
center point.
center line
fig. 7
fig. 6
fig. 8
Loading...