Page 1
Product Information Packet
WDM3558TP-9
2HP,1750RPM,3PH,60HZ,145T,3524M,TEFC,F3
Copyright © All product information within this document is subject to ABB Motors and Mechanical Inc. copyright © protection, unless otherwise noted.
Page 2
Product Information Packet: WDM3558TP-9 - 2HP,1750RPM,3PH,60HZ,145T,3524M,TEFC,F3
Part Detail
Revision: K Status: INA/A Change #: Proprietary: No
Type: AC Elec. Spec: 35WGL073 CD Diagram: CD0005 Mfg Plant:
Mech. Spec: 35E2679 Layout: 35LYE2679 Poles: 04 Created Date: 06-03-2014
Base: RG Eff. Date: 03-08-2016 Leads: 9#18
Specs
Catalog Number: WDM3558TP-9
Enclosure: TEFC
Frame: 145T
Frame Material: Steel
Output @ Frequency: 2.000 HP @ 60 HZ
Synchronous Speed @ Frequency: 1800 RPM @ 60 HZ
Voltage @ Frequency: 230.0 V @ 60 HZ
460.0 V @ 60 HZ
XP Division: Not Applicable
Agency Approvals: UR
CSA
Auxillary Box: No Auxillary Box
Auxillary Box Lead Termination: None
Base Indicator: RG
Bearing Grease Type: Polyrex EM (-20F +300F)
Blower: None
Current @ Voltage: 3.100 A @ 460.0 V
Insulation Class: F
Inverter Code: Not Inverter
KVA Code: L
Lifting Lugs: No Lifting Lugs
Locked Bearing Indicator: No Locked Bearing
Motor Lead Quantity/Wire Size: 9 @ 18 AWG
Motor Lead Exit: Ko Box
Motor Lead Termination: Flying Leads
Motor Type: 3524M
Mounting Arrangement: F3
Power Factor: 72
Product Family: Wash Down
Pulley End Bearing Type: Sealed Bearing
Pulley Face Code: Standard
Pulley Shaft Indicator: Standard
Rodent Screen: None
Shaft Extension Location: Pulley End
6.400 A @ 230.0 V
Shaft Ground Indicator: No Shaft Grounding
Page 2 of 10
Page 3
Product Information Packet: WDM3558TP-9 - 2HP,1750RPM,3PH,60HZ,145T,3524M,TEFC,F3
6.700 A @ 208.0 V
Design Code: C
Drip Cover: No Drip Cover
Duty Rating: CONT
Electrically Isolated Bearing: Not Electrically Isolated
Feedback Device: NO FEEDBACK
Front Face Code: Standard
Front Shaft Indicator: None
Heater Indicator: No Heater
Shaft Rotation: Reversible
Shaft Slinger Indicator: Shaft Slinger
Speed Code: Single Speed
Motor Standards: NEMA
Starting Method: Direct on line
Thermal Device - Bearing: None
Thermal Device - Winding: None
Vibration Sensor Indicator: No Vibration Sensor
Winding Thermal 1: None
Winding Thermal 2: None
Page 3 of 10
Page 4
Product Information Packet: WDM3558TP-9 - 2HP,1750RPM,3PH,60HZ,145T,3524M,TEFC,F3
Nameplate NP1496L
CAT.NO. WDM3558TP-9
SPEC. 35E2679L073H1
HP 2
VOLTS 230/460
AMP 6.4/3.1
RPM 1750
FRAME 145T HZ 60 PH 3
SER.F. 1.15 CODE L DES C CLASS F
NEMA-NOM-EFF 84 PF 72
RATING 40C AMB-CONT
CC USABLE AT 208V 6.7
DE 6205 ODE 6203
ENCL TEFC SN
Page 4 of 10
Page 5
Product Information Packet: WDM3558TP-9 - 2HP,1750RPM,3PH,60HZ,145T,3524M,TEFC,F3
Parts List
Part Number Description Quantity
SA282064 SA 35E2679L073H1 1.000 EA
RA268378 RA 35E2679L073H1 1.000 EA
34FN3002A01SP EXTERNAL FAN, PLASTIC, .637/.639 HUB W/ 1.000 EA
NS2512A01 INSULATOR, CONDUIT BOX X 1.000 EA
35CB3010A01W 35 CB .75 NPT @ 6:00, WHITE EPOXY 1.000 EA
35GS1022A03 GASKET BOX .125 THK WHITE NEOPRENE 1.000 EA
RM1006A03 GROMMET, #2867 1.12 HOLE (ATLANTIC INDIA 1.000 EA
51XB1016A08 10-16X 1/2HXWSSLD SERTYB 2.000 EA
HA5027A01 HA4066A01 T-DRAIN X2 BAGGED 1.000 EA
11XW1032G06 10-32 X .38, TAPTITE II, HEX WSHR SLTD U 1.000 EA
HW3001B01 BRASS CUP WASHER, FOR #10 SCREW 1.000 EA
35EP3122R07W FREP TEFC,"O" DRILLS,NO GRSR, CLIPPER 1.000 EA
HW4032A01 BLACK DRAIN PLUG FOR WASH DOWN MOTORS 3.000 EA
HW5100A03 WAVY WASHER (W1543-017) 1.000 EA
35PE3101A55MW PUEP ASSEMBLY FOR ROUTING 1.000 EA
HW4032A01 BLACK DRAIN PLUG FOR WASH DOWN MOTORS 3.000 EA
HW4606A02 JM CLIPPER/SEAL (LWE-0938-1624-AL23) 1.000 EA
XY1032S02 10-32 HEX NUT R.H. S STL 4.000 EA
51XB1214A16 12-14X1.00 HXWSSLD SERTYB 1.000 EA
35FH4005A32SP IEC FH NO GRSR W/3 HOLES - PRIMED 1.000 EA
11XW1032S06 10-32 X .38, TAPTITE II, HEX WSHR SLTD U 3.000 EA
HW4606A01 JM CLIPPER/SEAL (WDE-0667-1064-BH49) 1.000 EA
35CB4522 35 LIPPED CB LID PRIMED 1.000 EA
35GS1030A02 35 GS FOR CB LID - WHITE NEOPRENE 1.000 EA
Page 5 of 10
Page 6
Product Information Packet: WDM3558TP-9 - 2HP,1750RPM,3PH,60HZ,145T,3524M,TEFC,F3
Parts List (continued)
Part Number Description Quantity
59XW0832S07 TAPTITE II,HEX WSHR UNSLTD SER,410 S.S., 4.000 EA
HW2502D13 SS KEY, 3/16 SQ X 1.375 1.000 EA
HA7000A01 KEY RETAINER 7/8" DIA SHAFT 1.000 EA
MJ5001A27 32220KN GRAY SEALER *MIN BUY 4 QTS=1GAL 0.001 QT
85XU0407S04 4X1/4 U DRIVE PIN STAINLESS 2.000 EA
LB1164 LABEL,WARNING AND DRAIN 1.000 EA
MJ1000A02 GREASE, MOBIL POLYREX EM - 124047 0.050 LB
MG1025Z02 ACTIVATOR WILKOFAST 060.02HF 0.010 GA
MG1025W01 WILKOFAST, 781.01, SIGNAL WHITE #9003 0.017 GA
HA3100S09 THRUBOLT 9.25 LENGTH SS 4.000 EA
LC0005 CONN.DIA.,TY M,9-LD,DUAL VOLT,REVERSING 1.000 EA
NP1496L SS WD UL CSA CC 1.000 EA
36PA1001 PKG GRP, PRINT PK1017A06 1.000 EA
MN416A01 TAG-INSTAL-MAINT no wire (1200/bx) 3/19 1.000 EA
Page 6 of 10
Page 7
Product Information Packet: WDM3558TP-9 - 2HP,1750RPM,3PH,60HZ,145T,3524M,TEFC,F3
AC Induction Motor Performance Data
Record # 50342 - Typical performance - not guaranteed values
Winding: 35WGL073-R001 Type: 3524M Enclosure: TEFC
Nameplate Data
460 V, 60 Hz:
High Voltage Connection
Rated Output (HP) 2 Full Load Torque 5.99 LB-FT
Volts 230/460 Start Configuration direct on line
Full Load Amps 6.4/3.1 Breakdown Torque 23.9 LB-FT
R.P.M. 1750 Pull-up Torque 15.2 LB-FT
Hz 60 Phase 3 Locked-rotor Torque 19.5 LB-FT
NEMA Design Code C KVA Code L Starting Current 24.2 A
Service Factor (S.F.) 1.15 No-load Current 2.33 A
NEMA Nom. Eff. 84 Power Factor 72 LinelineRes.@25ºC 7.97Ω
Rating - Duty 40C AMB-CONT Temp. Rise @ Rated Load 68°C
S.F. Amps Temp. Rise @ S.F. Load 80°C
Locked-rotor Power Factor 54.3
Rotor inertia 0.142 LB-FT2
Load Characteristics 460 V, 60 Hz, 2 HP
% of Rated Load 25 50 75 100 125 150 S.F.
Power Factor 27 44 58 68 75 79 72
Efficiency 73 82 84.5 85.1 84.3 83 84.6
Speed 1790 1778 1766 1753 1737 1721 1743
Line amperes 2.38 2.55 2.86 3.24 3.7 4.27 3.52
Page 7 of 10
Page 8
Product Information Packet: WDM3558TP-9 - 2HP,1750RPM,3PH,60HZ,145T,3524M,TEFC,F3
Performance Graph at 460V, 60Hz, 2.0HP Typical performance - Not guaranteed values
Page 8 of 10
Page 9
Product Information Packet: WDM3558TP-9 - 2HP,1750RPM,3PH,60HZ,145T,3524M,TEFC,F3
510-526 = 13 29
527-533 = 14 16
534-544 = 15 53
2 50
8750
8745
3 75
5 94
5 00
4 00 2 25
50
2 25
7 19
DIA
6 HOLES
38 DIA
4 HOLES
3 W/PLUGS
(EACH END)
19 KEY
1 38 LONG
6 61
5 79
6 81
3 50
+-00
06
4 70
6 50
2 75 2 75
3 25
TOP
OF NP
LEAD HOLE
75 N P T
PULLEY END DETAIL
FRONT END DETAIL
JM CLIPPER
SEAL
(EACH END)
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
35LYE2679
B
HOR 143-5T TEFC M WD F3 ENCAP W/JM CLIP SEAL
SH 1 of 1
REV. DESC
REV
BY
REVISED
MODEL NO.
VERSION
TDR
REF
35LYE2679
LOADING OF SWD DWG FOR 2D TO 3D CONVERSION - PKG11
ENALEM0
E
01 13 27 11/30/2018
-
000001092572
05
35LYE2679
CUSTOMER IS RESPONSIBLE FOR DETERMINING THAT THE PRODUCT WILL PERFORM SUITABLY IN THE INTENDED APPLICATION
BALDOR - RELIANCE
®
Page 9 of 10
Page 10
Product Information Packet: WDM3558TP-9 - 2HP,1750RPM,3PH,60HZ,145T,3524M,TEFC,F3
Page 10 of 10
Loading...