Product Information Packet
JMWDM3546T
1HP,1740RPM,3PH,60HZ,143JM,3518M,TENV,F1
Copyright © All product information within this document is subject to ABB Motors and Mechanical Inc. copyright © protection, unless otherwise noted.
Product Information Packet: JMWDM3546T - 1HP,1740RPM,3PH,60HZ,143JM,3518M,TENV,F1
Part Detail
Revision: J Status: INA/A Change #: Proprietary: No
Type: AC Elec. Spec: 35WGP439 CD Diagram: CD0005 Mfg Plant:
Mech. Spec: 35Z956 Layout: 35LYZ956 Poles: 04 Created Date: 11-21-2011
Base: RG Eff. Date: 03-08-2016 Leads: 9#18
Specs
Catalog Number: JMWDM3546T
Enclosure: TENV
Frame: 143JM
Frame Material: Steel
Output @ Frequency: 1.000 HP @ 60 HZ
Synchronous Speed @ Frequency: 1800 RPM @ 60 HZ
Voltage @ Frequency: 460.0 V @ 60 HZ
230.0 V @ 60 HZ
208.0 V @ 60 HZ
XP Division: Not Applicable
Agency Approvals: CSA
UR
Auxillary Box: No Auxillary Box
Auxillary Box Lead Termination: None
Base Indicator: RG
Bearing Grease Type: Polyrex EM (-20F +300F)
Blower: None
Insulation Class: F
Inverter Code: Not Inverter
KVA Code: M
Lifting Lugs: No Lifting Lugs
Locked Bearing Indicator: Locked Bearing
Motor Lead Quantity/Wire Size: 9 @ 18 AWG
Motor Lead Exit: Ko Box
Motor Lead Termination: Flying Leads
Motor Type: 3518M
Mounting Arrangement: F1
Power Factor: 74
Product Family: Wash Down
Pulley End Bearing Type: Sealed Bearing
Pulley Face Code: C-Face
Pulley Shaft Indicator: Tapped & Key
Rodent Screen: None
Shaft Extension Location: Pulley End
Current @ Voltage: 1.500 A @ 460.0 V
Shaft Ground Indicator: No Shaft Grounding
Page 2 of 10
Product Information Packet: JMWDM3546T - 1HP,1740RPM,3PH,60HZ,143JM,3518M,TENV,F1
3.000 A @ 230.0 V
3.200 A @ 208.0 V
Design Code: B
Drip Cover: No Drip Cover
Duty Rating: CONT
Electrically Isolated Bearing: Not Electrically Isolated
Feedback Device: NO FEEDBACK
Front Face Code: Standard
Front Shaft Indicator: None
Heater Indicator: No Heater
Shaft Rotation: Reversible
Shaft Slinger Indicator: Shaft Slinger
Speed Code: Single Speed
Motor Standards: NEMA
Starting Method: Direct on line
Thermal Device - Bearing: None
Thermal Device - Winding: None
Vibration Sensor Indicator: No Vibration Sensor
Winding Thermal 1: None
Winding Thermal 2: None
Page 3 of 10
Product Information Packet: JMWDM3546T - 1HP,1740RPM,3PH,60HZ,143JM,3518M,TENV,F1
Nameplate NP1496L
CAT.NO. JMWDM3546T
SPEC. 35Z956P439G1
HP 1
VOLTS 208-230/460
AMP 3.2-3/1.5
RPM 1740
FRAME 143JM HZ 60 PH 3
SER.F. 1.15 CODE M DES B CLASS F
NEMA-NOM-EFF 82.5 PF 74
RATING 40C AMB-CONT
CC USABLE AT 208V
DE 6206 ODE 6203
ENCL TENV SN
Page 4 of 10
Product Information Packet: JMWDM3546T - 1HP,1740RPM,3PH,60HZ,143JM,3518M,TENV,F1
Parts List
Part Number Description Quantity
SA235361 SA 35Z956P439G1 1.000 EA
RA222323 RA 35Z956P439G1 1.000 EA
NS2512A01 INSULATOR, CONDUIT BOX X 1.000 EA
35CB3010A01W 35 CB .75 NPT @ 6:00, WHITE EPOXY 1.000 EA
35GS1039 05 MOLDED GASKET W/LIP, 1.12 LEAD HOLE, 1.000 EA
51XB1016A08 10-16X 1/2HXWSSLD SERTYB 2.000 EA
HA5027A01 HA4066A01 T-DRAIN X2 BAGGED 1.000 EA
11XW1032G06 10-32 X .38, TAPTITE II, HEX WSHR SLTD U 1.000 EA
35EP3122D00W SPL FR ENDPLATE -TENV- SP.#9 (WHITE EPOX 1.000 EA
HW4032A01 BLACK DRAIN PLUG FOR WASH DOWN MOTORS 3.000 EA
HW5100A03 WAVY WASHER (W1543-017) 1.000 EA
35EP3401T07MW PU EP FOR SEAL W/"O" DRILLS & NO GRS, W/ 1.000 EA
HW4600B50 SEAL 1.156 X 1.874 X 0.250 SINGLE LIP DB 1.000 EA
HW4032A01 BLACK DRAIN PLUG FOR WASH DOWN MOTORS 3.000 EA
10XN1032S16 10-32X1 HEX HEAD S STEEL 2.000 EA
35CB4522 35 LIPPED CB LID PRIMED 1.000 EA
35GS1030A02 35 GS FOR CB LID - WHITE NEOPRENE 1.000 EA
59XW0832S07 TAPTITE II,HEX WSHR UNSLTD SER,410 S.S., 4.000 EA
HW4600B36SP V-RING SLINGER 1.188 X 1.690 X .24 VITON 1.000 EA
HW2502D13 SS KEY, 3/16 SQ X 1.375 1.000 EA
HA7000A01 KEY RETAINER 7/8" DIA SHAFT 1.000 EA
MJ5001A27 32220KN GRAY SEALER *MIN BUY 4 QTS=1GAL 0.001 QT
85XU0407S04 4X1/4 U DRIVE PIN STAINLESS 2.000 EA
LB1164 LABEL,WARNING AND DRAIN 1.000 EA
Page 5 of 10
Product Information Packet: JMWDM3546T - 1HP,1740RPM,3PH,60HZ,143JM,3518M,TENV,F1
Parts List (continued)
Part Number Description Quantity
MJ1000A02 GREASE, MOBIL POLYREX EM - 124047 0.050 LB
MG1025Z02 ACTIVATOR WILKOFAST 060.02HF 0.010 GA
MG1025W01 WILKOFAST, 781.01, SIGNAL WHITE #9003 0.017 GA
HA3100S07 THRUBOLT 10-32 X 8.375 SS 4.000 EA
LC0005 CONN.DIA.,TY M,9-LD,DUAL VOLT,REVERSING 1.000 EA
NP1496L SS WD UL CSA CC 1.000 EA
36PA1000 PKG GRP, PRINT PK1016A06 1.000 EA
MN416A01 TAG-INSTAL-MAINT no wire (1200/bx) 3/19 1.000 EA
Page 6 of 10
Product Information Packet: JMWDM3546T - 1HP,1740RPM,3PH,60HZ,143JM,3518M,TENV,F1
AC Induction Motor Performance Data
Record # 26368 - Typical performance - not guaranteed values
Winding: 35WGP439-R001 Type: 3518M Enclosure: TENV
Nameplate Data
460 V, 60 Hz:
High Voltage Connection
Rated Output (HP) 1 Full Load Torque 2.99 LB-FT
Volts 208-230/460 Start Configuration direct on line
Full Load Amps 3.26-3.02/1.51 Breakdown Torque 13.7 LB-FT
R.P.M. 1740 Pull-up Torque 8.94 LB-FT
Hz 60 Phase 3 Locked-rotor Torque 10.3 LB-FT
NEMA Design Code B KVA Code M Starting Current 13.2 A
Service Factor (S.F.) 1.15 No-load Current 0.997 A
NEMA Nom. Eff. 82.5 Power Factor 74 LinelineRes.@25ºC 16Ω
Rating - Duty 40C AMB-CONT Temp. Rise @ Rated Load 79°C
S.F. Amps Temp. Rise @ S.F. Load 98°C
Load Characteristics 460 V, 60 Hz, 1 HP
% of Rated Load 25 50 75 100 125 150 S.F.
Power Factor 33 51 65 74 80 84 78
Efficiency 69.7 79.7 82.6 83.2 82.5 81.1 82.8
Speed 1786 1771 1757 1742 1723 1704 1731
Line amperes 1.03 1.15 1.32 1.51 1.76 2.06 1.66
Page 7 of 10
Product Information Packet: JMWDM3546T - 1HP,1740RPM,3PH,60HZ,143JM,3518M,TENV,F1
Performance Graph at 460V, 60Hz, 1.0HP Typical performance - Not guaranteed values
Page 8 of 10
Product Information Packet: JMWDM3546T - 1HP,1740RPM,3PH,60HZ,143JM,3518M,TENV,F1
510-528 = 10 00
529-535 = 10 88
536-546 = 12 25
4 281
4 219
2 890
2 860
640
610
13
1 156
1 154
1 0000
9995
4 500
4 497
6 54
4 00
5 00
2 88
50
5 94
2 59
8745
8740
CHECK W/GAGE
T-9038
19 KEY
1 38 LONG
SLINGER
(4) 125 NPT HOLES
3 W/PLUGS
@3 9 & 11:00
PULLEY END)
38-16 TAP
88 DEEP
6 HOLES
38
(4) 125 NPT HOLES
3 W/PLUGS
@ 3 9 & 1:00
(FRONT END)
6 63
5 65
3 50
3 44
6 81
2 75 2 75
3 25
6 50
4 56
45° 45°
LEAD HOLE
75 N P T
4 HOLES
38-16 TAP ON
5 88 B C
1 25
PULLEY END DETAIL
USE SEALER UNDER
RETAINER SCREW
HEADS BEFORE INSTALLING
APPLY COAT OF SEALER
TO HOUSING BEFORE
PRESSING SEAL IN
NAMEPLATE
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
35LYZ956
B
STD HORZ 143-5JM TENV 35M WD W/.75 N.P.T. LH
SH 1 of 1
REV. DESC
REV
BY
REVISED
MODEL NO.
VERSION
TDR
REF
35LYZ956
LOADING OF SWD DWG FOR 2D TO 3D CONVERSION PKG 15
ENALEM0
C
09 34 03 01/22/2019
-
000001096905
03
35LYZ956
CUSTOMER IS RESPONSIBLE FOR DETERMINING THAT THE PRODUCT WILL PERFORM SUITABLY IN THE INTENDED APPLICATION
BALDOR - RELIANCE
®
Page 9 of 10
Product Information Packet: JMWDM3546T - 1HP,1740RPM,3PH,60HZ,143JM,3518M,TENV,F1
Page 10 of 10
Loading...