Product Information Packet
IDWNM3611T
3HP,1760RPM,3PH,60HZ,184TC,3640M,TENV,F1
Copyright © All product information within this document is subject to ABB Motors and Mechanical Inc. copyright © protection, unless otherwise noted.
Product Information Packet: IDWNM3611T - 3HP,1760RPM,3PH,60HZ,184TC,3640M,TENV,F1
Part Detail
Revision: L Status: PRD/A Change #: Proprietary: No
Type: AC Elec. Spec: 36WGS952 CD Diagram: CD0005 Mfg Plant:
Mech. Spec: 36J565 Layout: 36LYJ565 Poles: 04 Created Date: 05-31-2012
Base: RG Eff. Date: 04-20-2020 Leads: 9#16
Specs
Catalog Number: IDWNM3611T
Enclosure: TENV
Frame: 184TC
Frame Material: Steel
Output @ Frequency: 3.000 HP @ 60 HZ
Synchronous Speed @ Frequency: 1800 RPM @ 60 HZ
Voltage @ Frequency: 230.0 V @ 60 HZ
460.0 V @ 60 HZ
XP Class and Group: None
XP Division: Not Applicable
Agency Approvals: UR
CSA
Auxillary Box: No Auxillary Box
Auxillary Box Lead Termination: None
Base Indicator: Rigid
Bearing Grease Type: Polyrex EM (-20F +300F)
Blower: None
Insulation Class: H
Inverter Code: Inverter Duty
KVA Code: K
Lifting Lugs: No Lifting Lugs
Locked Bearing Indicator: Locked Bearing
Motor Lead Quantity/Wire Size: 9 @ 16 AWG
Motor Lead Exit: Ko Box
Motor Lead Termination: Flying Leads
Motor Type: 3640M
Mounting Arrangement: F1
Power Factor: 78
Product Family: Wash Down
Pulley End Bearing Type: Ball
Pulley Face Code: C-Face
Pulley Shaft Indicator: Standard
Rodent Screen: None
Shaft Extension Location: Pulley End
Current @ Voltage: 4.100 A @ 460.0 V
Shaft Ground Indicator: No Shaft Grounding
Page 2 of 10
Product Information Packet: IDWNM3611T - 3HP,1760RPM,3PH,60HZ,184TC,3640M,TENV,F1
8.200 A @ 230.0 V
Design Code: B
Drip Cover: No Drip Cover
Duty Rating: CONT
Electrically Isolated Bearing: Not Electrically Isolated
Feedback Device: NO FEEDBACK
Front Face Code: Encoder/Feedback Device
Front Shaft Indicator: None
Heater Indicator: No Heater
Shaft Rotation: Reversible
Shaft Slinger Indicator: Shaft Slinger
Speed Code: Single Speed
Motor Standards: NEMA
Starting Method: Direct on line
Thermal Device - Bearing: None
Thermal Device - Winding: Normally Closed Thermostat
Vibration Sensor Indicator: No Vibration Sensor
Winding Thermal 1: None
Winding Thermal 2: None
Page 3 of 10
Product Information Packet: IDWNM3611T - 3HP,1760RPM,3PH,60HZ,184TC,3640M,TENV,F1
Nameplate NP1608L
CAT NO IDWNM3611T
SPEC. 36J565S952G1
FRAME 184TC HP 3 TE
VOLTS 230/460
MAG CUR 4.2/2.1 FLA 8.2/4.1
RPM 1760 RPM MAX 6000
HZ 60 PH 3 CLASS H
SER.F. 1.00 DES B SL HZ 1.4
NEMA-NOM-EFF 89.5 WK2 0.372
BLWR V PH HZ A
RATING 40C AMB-CONT
DE BRG 6206 ODE BRG 6205
CC 010A SN
Page 4 of 10
Product Information Packet: IDWNM3611T - 3HP,1760RPM,3PH,60HZ,184TC,3640M,TENV,F1
Parts List
Part Number Description Quantity
SA245428 SA 36J565S952G1 1.000 EA
RA232315 RA 36J565S952G1 1.000 EA
36CB3005A03W 36 CB .75 NPT @ 6 W/WHITE EPOXY 1.000 EA
35GS1022A03 GASKET BOX .125 THK WHITE NEOPRENE 1.000 EA
51XB1016A08 10-16X 1/2HXWSSLD SERTYB 2.000 EA
HA5027A01 HA4066A01 T-DRAIN X2 BAGGED 1.000 EA
11XW1032G06 10-32 X .38, TAPTITE II, HEX WSHR SLTD U 1.000 EA
36EP3104A77MW FREP TENV 205 BRG, (WD) FOR THRU-SHAFT 1.000 EA
HW4032A01 BLACK DRAIN PLUG FOR WASH DOWN MOTORS 3.000 EA
HW4600B49 SEAL 0.938 X 1.624 X 0.250 SINGLE LIP DB 1.000 EA
HW5100A05 WVY WSHR F/205 & 304 BRGS 1.000 EA
36PE3301A27MW PUEP ASSEMBLY FOR ROUTING PURPOSES 1.000 EA
HW4032A01 BLACK DRAIN PLUG FOR WASH DOWN MOTORS 3.000 EA
HW4600B50 SEAL 1.156 X 1.874 X 0.250 SINGLE LIP DB 1.000 EA
10XN2520S26 1/4-20X 1 5/8 HEX HD SS 4.000 EA
35FH4801W THRU-SHAFT ENCODER COVER INV/VEC F1 & F2 1.000 EA
WD4129 1.50 X 1.50 GRAY SNAP IN PLUG PROMOULD # 2.000 EA
10XN2520S08 SCREW, 1/4-20 X 1/2 HHCS SS 4.000 EA
10XN2520S08 SCREW, 1/4-20 X 1/2 HHCS SS 1.000 EA
36CB4518 36 LIPPED CB LID PRIMED 1.000 EA
37GS3010SP 1/16"WHITE LID GASKET 1.000 EA
59XW0832S07 TAPTITE II,HEX WSHR UNSLTD SER,410 S.S., 4.000 EA
HW1003S08 WASHER, #8 EX TH LK, SS 4.000 EA
HW4600B36SP V-RING SLINGER 1.188 X 1.690 X .24 VITON 1.000 EA
Page 5 of 10
Product Information Packet: IDWNM3611T - 3HP,1760RPM,3PH,60HZ,184TC,3640M,TENV,F1
Parts List (continued)
Part Number Description Quantity
HW2502E16 #303 SS,SQ KEY 1/4 X 1.750 1.000 EA
HA7000A02 KEY RETAINER RING, 1 1/8 DIA, 1 3/8 DIA 1.000 EA
MJ5004A05 #242-21 LOCTITE GENERAL PURPOSE MED. STR 0.005 EA
MJ5001A27 32220KN GRAY SEALER *MIN BUY 4 QTS=1GAL 0.001 QT
85XU0407S04 4X1/4 U DRIVE PIN STAINLESS 2.000 EA
LB1164 LABEL,WARNING AND DRAIN 1.000 EA
HW3200A01 3/8-16X3/4 I-BLT WELDED F/S 1.000 EA
MJ1000A02 GREASE, MOBIL POLYREX EM - 124047 0.050 LB
MG1025Z02 ACTIVATOR WILKOFAST 060.02HF 0.010 GA
MG1025W01 WILKOFAST, 781.01, SIGNAL WHITE #9003 0.022 GA
HA3101S28 THRUBOLT- 1/4-20 X 12.50 SS 4.000 EA
LB1115N LABEL,LIFTING DEVICE (ON ROLLS) 1.000 EA
LC0145B01 CONNECTION LABEL 1.000 EA
NP1608L SS WD INV UL CSA CC REV MTG 1.000 EA
36PA1001 PKG GRP, PRINT PK1017A06 1.000 EA
MN416A01 TAG-INSTAL-MAINT no wire (1200/bx) 3/19 1.000 EA
Page 6 of 10
Product Information Packet: IDWNM3611T - 3HP,1760RPM,3PH,60HZ,184TC,3640M,TENV,F1
Load Characteristics at 460 Volts, 60 Hz, 3 HP
AC Induction Motor Performance Data
Record # 39007
Typical performance - not guaranteed values
Winding: 36WGS952 Type: 3640M Enclosure: TENV
Nameplate Data
General Characteristics at 460 V, 60 Hz:
High Volt Connection
Rated Output (HP) 3
Full Load
Torque
9.1 LB-FT
Volts 208-230/460
Start
Configuration
DOL
Full Load Amps 8.6-8.2/4.1
Break Down
Torque
35 LB-FT
R.P.M. 1760
Pull-Up
Torque
18.8 LB-FT
Hz 60 Phase 3
Locked-rotor
Torque
22.7 LB-FT
NEMA Design
Code
B KVA Code K
Starting
Current
32.9 Amps
Service Factor 1
No-load
Current
2.09 Amps
NEMA Nom. Eff. 89.5 P.F. 78
Line-line Res. @ 25°C.
3.3157 Ohms
Rating - Duty 40C AMB-CONT
Temp. Rise
@ Rated Load
74°C
S.F. Amps
Temp. Rise
@ S.F. Load
% of Rated
Load
25 50 75 100 125 150 S.F.
Power Factor 38 60 71 78 82 84
Efficiency 83.8 89.3 90.4 90.3 89.6 88.5
Speed 1790.1 1780.3 1769.9 1758.7 1746.6 1732.6
Line Amperes 2.29 2.72 3.34 4.05 4.86 5.75
Baldor Electric Company Fort Smith, Arkansas
Page
1
of
1
AC Induction Motor Performance Data
3/6/2013
Page 7 of 10
Product Information Packet: IDWNM3611T - 3HP,1760RPM,3PH,60HZ,184TC,3640M,TENV,F1
Catalog IDWNM3611TNP VOLTS
230/460
ENCLOSURE TENV
FRAME 184TC NP AMPS
8.2/4.1
Base Volts
460 R1 1.640 X1 5.143
HP 3 HP DUTY Cont Base AMPS 4.05 R2 1.260 X2 4.486
BASE SPEED 1800 MAX SAFE RPM 6000 Slip Hz 1.37 XM 120.167
PHASE/HZ 3/60
AMB
0
C/INSUL
40/H
WK
2
(lb-ft
2
)
0.372
Remarks: Calculated Data
DR BY ENR
CK BY
APP BY ENR
DATE
3/6/2013
ISSUE DATE
WYE CONN EQ CKT OHMS PER PHASE (BASE RATING, 20C)
A-C MOTOR
PERFORMANCE CURVES
36J565S952G1
3/6/2013
Rated Torque
PeakTorque
Amps
Base
Maximum Rating
Horsepower
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
0.00
5.00
10.00
15.00
20.00
25.00
30.00
35.00
0 1000 2000 3000 4000 5000 6000
Horsepower & Amps
Torque (Lb-Ft)
Speed (RPM)
Page 8 of 10
Product Information Packet: IDWNM3611T - 3HP,1760RPM,3PH,60HZ,184TC,3640M,TENV,F1
614-623 = 16 40
624-634 = 17 78
635-646 = 19 28
2 62 25
4 50
5 50
6 50
50
8 500
8 497
8 85
1 1250
1 1245
2 78
5 50
2 75
3 50
FORSHEDA
SLINGER
25 KEY
1 75 LONG
(635-646 ONLY)
6 HOLES
Ø 41
PLUG
(EACH SIDE)
NAMEPLATE
6 92
45° 45°
3 75 3 75
4 31
8 63
4 50
4 44
7 86
5 79
8 43
2 24
LEAD HOLE
75 N P T
4 HOLES
50-13 TAP ON
Ø7 25 B C
PULLEY END DETAIL
APPLY COAT OF
GRAY SEALER UNDER
RETAINER RING SCREW HEADS
BEFORE INSTALLING
APPLY COAT OF SEALER
TO HOUSING BEFORE
PRESSING SEAL IN
FRONT END DETAIL
APPLY COAT OF SEALER
TO HOUSING BEFORE
PRESSING SEAL IN
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
36LYJ565
B
HORZ 182-4TC TENV 36M WD (S/P#9) INVERTER THRU-SHAFT ENCODER
REV. DESC
REV
BY
REVISED
MODEL NO.
VERSION
TDR
REF
36LYJ565
LOAD INOPC CREATED SWD DRG INTO BUS - PACKAGE 37
ENSTEK0
F
11 51 49 09/19/2019
-
000001120280
02
36LYJ565
CUSTOMER IS RESPONSIBLE FOR DETERMINING THAT THE PRODUCT WILL PERFORM SUITABLY IN THE INTENDED APPLICATION
BALDOR - RELIANCE
®
Page 9 of 10
Product Information Packet: IDWNM3611T - 3HP,1760RPM,3PH,60HZ,184TC,3640M,TENV,F1
Page 10 of 10
Loading...