Product Information Packet
IDWNM3554T
1.5HP,1755RPM,3PH,60HZ,145TC,3534M,TENV
Copyright © All product information within this document is subject to ABB Motors and Mechanical Inc. copyright © protection, unless otherwise noted.
Product Information Packet: IDWNM3554T - 1.5HP,1755RPM,3PH,60HZ,145TC,3534M,TENV
Part Detail
Revision: U Status: PRD/A Change #: Proprietary: No
Type: AC Elec. Spec: 35WGM613 CD Diagram: CD0005 Mfg Plant:
Mech. Spec: 35TT996 Layout: 35LYTT996 Poles: 04 Created Date: 12-21-2009
Base: RG Eff. Date: 04-20-2020 Leads: 9#18
Specs
Catalog Number: IDWNM3554T
Enclosure: TENV
Frame: 145TC
Frame Material: Steel
Output @ Frequency: 1.500 HP @ 60 HZ
Synchronous Speed @ Frequency: 1800 RPM @ 60 HZ
Voltage @ Frequency: 460.0 V @ 60 HZ
230.0 V @ 60 HZ
XP Class and Group: None
XP Division: Not Applicable
Agency Approvals: CSA
UR
Auxillary Box: No Auxillary Box
Auxillary Box Lead Termination: None
Base Indicator: Rigid
Bearing Grease Type: Polyrex EM (-20F +300F)
Blower: None
Insulation Class: H
Inverter Code: Inverter Duty
KVA Code: K
Lifting Lugs: No Lifting Lugs
Locked Bearing Indicator: Locked Bearing
Motor Lead Quantity/Wire Size: 9 @ 18 AWG
Motor Lead Exit: Ko Box
Motor Lead Termination: Flying Leads
Motor Type: 3534M
Mounting Arrangement: F1
Power Factor: 76
Product Family: Wash Down
Pulley End Bearing Type: Sealed Bearing
Pulley Face Code: C-Face
Pulley Shaft Indicator: Standard
Rodent Screen: None
RoHS Status: ROHS COMPLIANT
Current @ Voltage: 2.100 A @ 460.0 V
Shaft Extension Location: Pulley End
Page 2 of 10
Product Information Packet: IDWNM3554T - 1.5HP,1755RPM,3PH,60HZ,145TC,3534M,TENV
4.200 A @ 230.0 V
4.400 A @ 208.0 V
Design Code: B
Drip Cover: No Drip Cover
Duty Rating: CONT
Electrically Isolated Bearing: Not Electrically Isolated
Feedback Device: NO FEEDBACK
Front Face Code: Encoder/Feedback Device
Front Shaft Indicator: None
Heater Indicator: No Heater
Shaft Ground Indicator: No Shaft Grounding
Shaft Rotation: Reversible
Shaft Slinger Indicator: Shaft Slinger
Speed Code: Single Speed
Motor Standards: NEMA
Starting Method: Direct on line
Thermal Device - Bearing: None
Thermal Device - Winding: Normally Closed Thermostat
Vibration Sensor Indicator: No Vibration Sensor
Winding Thermal 1: None
Winding Thermal 2: None
Page 3 of 10
Product Information Packet: IDWNM3554T - 1.5HP,1755RPM,3PH,60HZ,145TC,3534M,TENV
Nameplate NP1608L
CAT NO IDWNM3554T
SPEC. 35TT996M613
FRAME 145TC HP 1.5 TE
VOLTS 230/460
MAG CUR 2.4/1.2 FLA 4.2/2.1
RPM 1755 RPM MAX 4500
HZ 60 PH 3 CLASS H
SER.F. 1.00 DES B SL HZ 1.5
NEMA-NOM-EFF 86.5 WK2 0.2
BLWR V PH HZ A
RATING 40C AMB-CONT
DE BRG 6205 ODE BRG 6203
CC 010A SN
Page 4 of 10
Product Information Packet: IDWNM3554T - 1.5HP,1755RPM,3PH,60HZ,145TC,3534M,TENV
Parts List
Part Number Description Quantity
SA188989 SA 35TT996M613 1.000 EA
RA176709 RA 35TT996M613 1.000 EA
NS2512A01 INSULATOR, CONDUIT BOX X 1.000 EA
35CB3010A01G 35 CB .75 NPT @ 6:00 (GRAY) 1.000 EA
35GS1039 05 MOLDED GASKET W/LIP, 1.12 LEAD HOLE, 1.000 EA
51XB1016A08 10-16X 1/2HXWSSLD SERTYB 2.000 EA
HA5027A02 HA4054 T-DRAIN X2 BAGGED WITH LABEL 1.000 EA
11XW1032G06 10-32 X .38, TAPTITE II, HEX WSHR SLTD U 1.000 EA
35EP3122R17W CUSTOM ODE,203 BRG,1.123SH,.125NPT DRNS, 1.000 EA
HW4072A01 BLACK DRAIN PLUG FOR .125 NPT 3.000 EA
HW4600A09 SEAL 0.656 X 1.124 X 0.250 DOUBLE SHIELD 1.000 EA
HW5100A03 WAVY WASHER (W1543-017) 1.000 EA
35EP3307E00W MASTER DE,205 BRG,1.623SH,.125NPT DRNS,C 1.000 EA
HW4072A01 BLACK DRAIN PLUG FOR .125 NPT 3.000 EA
HW4600B49 SEAL 0.938 X 1.624 X 0.250 SINGLE LIP DB 1.000 EA
12XN1032S20 10-32 X 1-1/4 HEX M.S. , STAINLESS STEEL 2.000 EA
35FH4801W THRU-SHAFT ENCODER COVER INV/VEC F1 & F2 1.000 EA
WD4129 1.50 X 1.50 GRAY SNAP IN PLUG PROMOULD # 2.000 EA
10XN2520S08 SCREW, 1/4-20 X 1/2 HHCS SS 4.000 EA
10XN2520S08 SCREW, 1/4-20 X 1/2 HHCS SS 1.000 EA
35CB4522 35 LIPPED CB LID PRIMED 1.000 EA
35GS1030A02 35 GS FOR CB LID - WHITE NEOPRENE 1.000 EA
59XW0832S07 TAPTITE II,HEX WSHR UNSLTD SER,410 S.S., 4.000 EA
HW4600B46 V-RING SLINGER 0.875 X 1.420 X .24 VITON 1.000 EA
Page 5 of 10
Product Information Packet: IDWNM3554T - 1.5HP,1755RPM,3PH,60HZ,145TC,3534M,TENV
Parts List (continued)
Part Number Description Quantity
HW2502D13 SS KEY, 3/16 SQ X 1.375 1.000 EA
HA7000A01 KEY RETAINER 7/8" DIA SHAFT 1.000 EA
MJ5004A05 #242-21 LOCTITE GENERAL PURPOSE MED. STR 0.005 EA
MJ5001A27 32220KN GRAY SEALER *MIN BUY 4 QTS=1GAL 0.001 QT
85XU0407S04 4X1/4 U DRIVE PIN STAINLESS 2.000 EA
LB1164 LABEL,WARNING AND DRAIN 1.000 EA
MJ1000A02 GREASE, MOBIL POLYREX EM - 124047 0.050 LB
MG1025Z02 ACTIVATOR WILKOFAST 060.02HF 0.010 GA
MG1025W01 WILKOFAST, 781.01, SIGNAL WHITE #9003 0.017 GA
HA3100S09 THRUBOLT 9.25 LENGTH SS 4.000 EA
LC0145B01 CONNECTION LABEL 1.000 EA
NP1608L SS WD INV UL CSA CC REV MTG 1.000 EA
36PA1000 PKG GRP, PRINT PK1016A06 1.000 EA
MN416A01 TAG-INSTAL-MAINT no wire (1200/bx) 3/19 1.000 EA
PE-0000002 ZRTG PE ASSEMBLY 1.000 EA
Page 6 of 10
Product Information Packet: IDWNM3554T - 1.5HP,1755RPM,3PH,60HZ,145TC,3534M,TENV
Load Characteristics at 460 Volts, 60 Hz, 1.5 HP
AC Induction Motor Performance Data
Record # 36529
Typical performance - not guaranteed values
Winding: 35WGM613 Type: 3533M Enclosure: TENV
Nameplate Data
General Characteristics at 460 V, 60 Hz:
High Volt Connection
Rated Output (HP) 1.5
Full Load
Torque
4.45 LB-FT
Volts 230/460
Start
Configuration
DOL
Full Load Amps 4.2/2.1
Break Down
Torque
20.8 LB-FT
R.P.M. 1755
Pull-Up
Torque
11.7 LB-FT
Hz 60 Phase 3
Locked-rotor
Torque
14.6 LB-FT
NEMA Design
Code
B KVA Code K
Starting
Current
20 Amps
Service Factor 1
No-load
Current
1.17 Amps
NEMA Nom. Eff. 86.5 P.F. 76
Line-line Res. @ 25°C.
8.44 Ohms
Rating - Duty 40C AMB-CONT
Temp. Rise
@ Rated Load
77°C
S.F. Amps
Temp. Rise
@ S.F. Load
% of Rated
Load
25 50 75 100 125 150 S.F.
Power Factor 35 54 68 76 81 84
Efficiency 80.5 87.1 88.3 88.8 88.3 87.4
Speed 1791 1782 1773 1764 1753 1743
Line Amperes 1.26 1.46 1.76 2.07 2.45 2.87
Baldor Electric Company Fort Smith, Arkansas
Page
1
of
1
AC Induction Motor Performance Data
3/1/2013
Page 7 of 10
Product Information Packet: IDWNM3554T - 1.5HP,1755RPM,3PH,60HZ,145TC,3534M,TENV
Catalog IDWNM3554TNP VOLTS
230/460
ENCLOSURE TENV
FRAME 145TC NP AMPS
4.2/2.1
Base Volts
460 R1 4.140 X1 8.770
HP 1.5 HP DUTY Cont Base AMPS 2.07 R2 2.710 X2 7.810
BASE SPEED 1800 MAX SAFE RPM 4500 Slip Hz 1.20 XM 217.396
PHASE/HZ 3/60
AMB
0
C/INSUL
40/H
WK
2
(lb-ft
2
)
0.195
Remarks: Calculated Data
DR BY ENR
CK BY
APP BY ENR
DATE
3/1/2013
ISSUE DATE
WYE CONN EQ CKT OHMS PER PHASE (BASE RATING, 20C)
A-C MOTOR
PERFORMANCE CURVES
35TT996M613
3/1/2013
Rated Torque
PeakTorque
Amps
Base
Maximum Rating
Horsepower
0.0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
0.00
5.00
10.00
15.00
20.00
25.00
0 500 1000 1500 2000 2500 3000 3500 4000 4500
Horsepower & Amps
Torque (Lb-Ft)
Speed (RPM)
Page 8 of 10
Product Information Packet: IDWNM3554T - 1.5HP,1755RPM,3PH,60HZ,145TC,3534M,TENV
8750
8745
4 500
4 497
6 49
2 12
13
13
510-528 = 14 90
529-535 = 15 78
536-546 = 17 15
2 78 2 59
4 00 2 75
5 00
5 94
50
19 KEY
1 38 LONG
NAMEPLATE
PLUG
(EACH SIDE)
(4) 125 NPT HOLES
3 W/PLUGS
@ 3 9 & 1:00
(4) 125 NPT HOLES
3 W/PLUGS
@ 3 9 & 11:00
FORSHEDA
SLINGER
6 HOLES
Ø 38
2 75 2 75
4 62 3 25
6 50
3 50
3 44
6 81
5 81
6 61
45°
45°
LEAD HOLE
75 N P T
4 HOLES
38-16 TAP ON
Ø5 88 B C
07
PULLEY END DETAIL
OMIT LOCK-WASHER &
COAT ENTIRE SCREW
HEAD W/SEALER
BEFORE INSTALLING
APPLY COAT OF
SEALER TO
HOUSING BEFORE
PRESSING SEAL IN
FRONT END DETAIL
APPLY COAT OF
SEALER TO
HOUSING BEFORE
PRESSING SEAL IN
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
35LYTT996
B
HOR 143-5TC TENV 35M WD INV (THRU-SH ENC W/ COVER) 2 POLE
SH 1 of 1
REV. DESC
REV
BY
REVISED
MODEL NO.
VERSION
TDR
REF
35LYTT996
LOAD INOPC CREATED SWD DRG INTO BUS - PACKAGE 13
USBUFRA
C
11 43 22 12/20/2018
-
000001094435
03
35LYTT996
CUSTOMER IS RESPONSIBLE FOR DETERMINING THAT THE PRODUCT WILL PERFORM SUITABLY IN THE INTENDED APPLICATION
BALDOR - RELIANCE
®
Page 9 of 10
Product Information Packet: IDWNM3554T - 1.5HP,1755RPM,3PH,60HZ,145TC,3534M,TENV
Page 10 of 10
Loading...