Page 1
Product Information Packet
CWDM3534
.33HP,1755RPM,3PH,60HZ,56C,3512M,TENV,F1
Copyright © All product information within this document is subject to ABB Motors and Mechanical Inc. copyright © protection, unless otherwise noted.
Page 2
Product Information Packet: CWDM3534 - .33HP,1755RPM,3PH,60HZ,56C,3512M,TENV,F1
Part Detail
Revision: L Status: PRD/A Change #: Proprietary: No
Type: AC Elec. Spec: 35WGL029 CD Diagram: CD0005 Mfg Plant:
Mech. Spec: 35S588 Layout: 35LYS588 Poles: 04 Created Date: 12-18-2013
Base: RG Eff. Date: 03-10-2020 Leads: 9#18
Specs
Catalog Number: CWDM3534
Enclosure: TENV
Frame: 56C
Frame Material: Steel
Output @ Frequency: .330 HP @ 60 HZ
Synchronous Speed @ Frequency: 1800 RPM @ 60 HZ
Voltage @ Frequency: 208.0 V @ 60 HZ
230.0 V @ 60 HZ
460.0 V @ 60 HZ
XP Class and Group: None
XP Division: Not Applicable
Agency Approvals: UR
CSA
Auxillary Box: No Auxillary Box
Auxillary Box Lead Termination: None
Base Indicator: Rigid
Bearing Grease Type: Polyrex EM (-20F +300F)
Heater Indicator: No Heater
Insulation Class: F
Inverter Code: Not Inverter
KVA Code: P
Lifting Lugs: No Lifting Lugs
Locked Bearing Indicator: Locked Bearing
Motor Lead Quantity/Wire Size: 9 @ 18 AWG
Motor Lead Exit: Ko Box
Motor Lead Termination: Flying Leads
Motor Type: 3512M
Mounting Arrangement: F1
Power Factor: 61
Product Family: Wash Down
Pulley End Bearing Type: Sealed Bearing
Pulley Face Code: C-Face
Pulley Shaft Indicator: Standard
Rodent Screen: None
Blower: None
Shaft Extension Location: Pulley End
Page 2 of 10
Page 3
Product Information Packet: CWDM3534 - .33HP,1755RPM,3PH,60HZ,56C,3512M,TENV,F1
Current @ Voltage: .650 A @ 460.0 V
1.300 A @ 208.0 V
1.300 A @ 230.0 V
Design Code: B
Drip Cover: No Drip Cover
Duty Rating: CONT
Electrically Isolated Bearing: Not Electrically Isolated
Feedback Device: NO FEEDBACK
Front Face Code: Standard
Front Shaft Indicator: None
Shaft Ground Indicator: No Shaft Grounding
Shaft Rotation: Reversible
Shaft Slinger Indicator: No Slinger
Speed Code: Single Speed
Motor Standards: NEMA
Starting Method: Direct on line
Thermal Device - Bearing: None
Thermal Device - Winding: None
Vibration Sensor Indicator: No Vibration Sensor
Winding Thermal 1: None
Winding Thermal 2: None
Page 3 of 10
Page 4
Product Information Packet: CWDM3534 - .33HP,1755RPM,3PH,60HZ,56C,3512M,TENV,F1
Nameplate NP1496L
CAT.NO. CWDM3534
SPEC. 35S588L029G1
HP .33
VOLTS 208-230/460
AMP 1.3/.65
RPM 1755
FRAME 56C HZ 60 PH 3
SER.F. 1.25 CODE P DES B CLASS F
NEMA-NOM-EFF 75.5 PF 61
RATING 40C AMB-CONT
CC USABLE AT 208V
DE 6205 ODE 6203
ENCL TENV SN
SFA 1.4/.7
Page 4 of 10
Page 5
Product Information Packet: CWDM3534 - .33HP,1755RPM,3PH,60HZ,56C,3512M,TENV,F1
Parts List
Part Number Description Quantity
SA274243 SA 35S588L029G1 1.000 EA
RA260830 RA 35S588L029G1 1.000 EA
NS2512A01 INSULATOR, CONDUIT BOX X 1.000 EA
35CB3008A01G SPL CONDUIT BOX, MACHINED GRAY 1.000 EA
35GS1040 35 MOLDED GASKET W/LIP, LEAD SEAL, 1.000 EA
51XB1016A08 10-16X 1/2HXWSSLD SERTYB 2.000 EA
11XW1032G06 10-32 X .38, TAPTITE II, HEX WSHR SLTD U 1.000 EA
35EP3122D00W MASTER ODE,203 BRG,.125NPT DRNS(WHITE) 1.000 EA
HW4072A01 BLACK DRAIN PLUG FOR .125 NPT 3.000 EA
HW5100A03 WAVY WASHER (W1543-017) 1.000 EA
35EP3307E00W MASTER DE,205 BRG,1.623SH,.125NPT DRNS,C 1.000 EA
HW4072A01 BLACK DRAIN PLUG FOR .125 NPT 3.000 EA
HW4600B49 SEAL 0.938 X 1.624 X 0.250 SINGLE LIP DB 1.000 EA
12XN1032S20 10-32 X 1-1/4 HEX M.S. , STAINLESS STEEL 2.000 EA
35CB4522 35 LIPPED CB LID PRIMED 1.000 EA
35GS1030A02 35 GS FOR CB LID - WHITE NEOPRENE 1.000 EA
59XW0832S07 TAPTITE II,HEX WSHR UNSLTD SER,410 S.S., 4.000 EA
HW4600B46 V-RING SLINGER 0.875 X 1.420 X .24 VITON 1.000 EA
HW2502D13 SS KEY, 3/16 SQ X 1.375 1.000 EA
HA7000A04 KEY RETAINER 0.625 DIA SHAFTS 1.000 EA
MJ5001A27 32220KN GRAY SEALER *MIN BUY 4 QTS=1GAL 0.001 QT
85XU0407S04 4X1/4 U DRIVE PIN STAINLESS 2.000 EA
LB1164 LABEL,WARNING AND DRAIN 1.000 EA
HA5027A02 HA4054 T-DRAIN X2 BAGGED WITH LABEL 1.000 EA
Page 5 of 10
Page 6
Product Information Packet: CWDM3534 - .33HP,1755RPM,3PH,60HZ,56C,3512M,TENV,F1
Parts List (continued)
Part Number Description Quantity
MJ1000A02 GREASE, MOBIL POLYREX EM - 124047 0.050 LB
MG1025Z02 ACTIVATOR WILKOFAST 060.02HF 0.010 GA
MG1025W01 WILKOFAST, 781.01, SIGNAL WHITE #9003 0.017 GA
HA3100S08 THRUBOLT 7.375LG SS 4.000 EA
LC0005 CONN.DIA.,TY M,9-LD,DUAL VOLT,REVERSING 1.000 EA
MN416A01 TAG-INSTAL-MAINT no wire (1200/bx) 3/19 1.000 EA
NP1496L SS WD UL CSA CC 1.000 EA
35PA1066 PKG GRP, PRINT PK1008A06 1.000 EA
PE-0000002 ZRTG PE ASSEMBLY 1.000 EA
FE-0000001 ZRTG FE ASSEMBLY 1.000 EA
Page 6 of 10
Page 7
Product Information Packet: CWDM3534 - .33HP,1755RPM,3PH,60HZ,56C,3512M,TENV,F1
AC Induction Motor Performance Data
Record # 44202 - Typical performance - not guaranteed values
Winding: 35WGL029-R001 Type: 3512M Enclosure: TENV
Nameplate Data
460 V, 60 Hz:
High Voltage Connection
Rated Output (HP) .33 Full Load Torque 0.971 LB-FT
Volts 208-230/460 Start Configuration direct on line
Full Load Amps 1.3/.65 Breakdown Torque 5.35 LB-FT
R.P.M. 1755 Pull-up Torque 3.65 LB-FT
Hz 60 Phase 3 Locked-rotor Torque 4.15 LB-FT
NEMA Design Code B KVA Code P Starting Current 5.24 A
Service Factor (S.F.) 1.25 No-load Current 0.51 A
NEMA Nom. Eff. 75.5 Power Factor 61 LinelineRes.@25ºC 42.4Ω
Rating - Duty 40C AMB-CONT Temp. Rise @ Rated Load 42°C
S.F. Amps 1.4/.7 Temp. Rise @ S.F. Load 49°C
Locked-rotor Power Factor 77
Rotor inertia 0.0709 LB-FT2
Load Characteristics 460 V, 60 Hz, 0.33 HP
% of Rated Load 25 50 75 100 125 150 S.F.
Power Factor 26 40 52 61 68 74 68
Efficiency 50.9 66.6 73.7 76.2 77.6 77.4 77.6
Speed 1791 1780 1769 1755 1740 1725 1740
Line amperes 0.52 0.54 0.59 0.65 0.71 0.8 0.71
Page 7 of 10
Page 8
Product Information Packet: CWDM3534 - .33HP,1755RPM,3PH,60HZ,56C,3512M,TENV,F1
Performance Graph at 460V, 60Hz, 0.33HP Typical performance - Not guaranteed values
Page 8 of 10
Page 9
Product Information Packet: CWDM3534 - .33HP,1755RPM,3PH,60HZ,56C,3512M,TENV,F1
510-520 = 11 06
521-528 = 12 05
529-535 = 12 93
536-546 = 14 30
1 88
2 06
13
6 49
4 500
4 497
6250
6245
4 32
3 00 2 75
66
2 59
(4) 125 NPT HOLES
3 w/PLUGS
@ 3 9 & 1:00
(FRONT END)
(4) 125 NPT HOLES
3 w/PLUGS
@ 3 9 & 11:00
(PULLEY END)
19 KEY
1 38 LONG
4 SLOTS
34 WIDE
NAMEPLATE
6 61
45° 45°
6 62
3 31
3 50
3 44
5 77
4 68
2 47
2 47
7 02
4 HOLES
38-16 TAP ON
5 88 DIA B C
LEAD HOLE
50 N P T
PULLEY END DETAIL
OMIT LOCK-WASHERS & APPLY
SEALER UNDER BEARING
RETAINER SCREW HEADS &
HOUSING O D BEFORE PRESSING
IN SEAL
CUSTOMER IS RESPONSIBLE FOR DETERMINING THAT BALDOR'S PRODUCT WILL PERFORM SUITABLY IN THE INTENDED APPLICATION
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
35LYS588
B
STD HORZ 56C TENV 35M WD (S/P #9)
SH 1 of 1
REV. DESC
REV
BY
REVISED
MODEL NO
VERSION
TDR
REF
35LYS588
LOADING OF SWD DWG FOR 2D TO 3D CONVERSION
ENALEM0
F
03 00 24 10/31/2018
-
000001089746
06
35LYS588
Material
-
BALDOR - RELIANCE
®
Page 9 of 10
Page 10
Product Information Packet: CWDM3534 - .33HP,1755RPM,3PH,60HZ,56C,3512M,TENV,F1
Page 10 of 10
Loading...