Page 1
Product Information Packet
CEWDM3558
2HP,1755RPM,3PH,60HZ,56C,3530M,TEFC,F1,N
Copyright © All product information within this document is subject to ABB Motors and Mechanical Inc. copyright © protection, unless otherwise noted.
Page 2
Product Information Packet: CEWDM3558 - 2HP,1755RPM,3PH,60HZ,56C,3530M,TEFC,F1,N
Part Detail
Revision: Q Status: PRD/A Change #: Proprietary: No
Type: AC Elec. Spec: 35WGM494 CD Diagram: CD0005 Mfg Plant:
Mech. Spec: 35S587 Layout: 35LYS587 Poles: 04 Created Date: 02-11-2015
Base: RG Eff. Date: 03-10-2020 Leads: 9#18
Specs
Catalog Number: CEWDM3558
Enclosure: TEFC
Frame: 56C
Frame Material: Steel
Output @ Frequency: 2.000 HP @ 60 HZ
Synchronous Speed @ Frequency: 1800 RPM @ 60 HZ
Voltage @ Frequency: 460.0 V @ 60 HZ
230.0 V @ 60 HZ
XP Class and Group: None
XP Division: Not Applicable
Agency Approvals: UR
CSA EEV
CSA
Auxillary Box: No Auxillary Box
Auxillary Box Lead Termination: None
Base Indicator: Rigid
Bearing Grease Type: Polyrex EM (-20F +300F)
Heater Indicator: No Heater
Insulation Class: F
Inverter Code: Inverter Ready
KVA Code: L
Lifting Lugs: No Lifting Lugs
Locked Bearing Indicator: Locked Bearing
Motor Lead Quantity/Wire Size: 9 @ 18 AWG
Motor Lead Exit: Ko Box
Motor Lead Termination: Flying Leads
Motor Type: 3530M
Mounting Arrangement: F1
Power Factor: 73
Product Family: Wash Down
Pulley End Bearing Type: Sealed Bearing
Pulley Face Code: C-Face
Pulley Shaft Indicator: Standard
Rodent Screen: None
Blower: None
Shaft Extension Location: Pulley End
Page 2 of 12
Page 3
Product Information Packet: CEWDM3558 - 2HP,1755RPM,3PH,60HZ,56C,3530M,TEFC,F1,N
Current @ Voltage: 2.900 A @ 460.0 V
5.800 A @ 230.0 V
6.000 A @ 208.0 V
Design Code: B
Drip Cover: No Drip Cover
Duty Rating: CONT
Electrically Isolated Bearing: Not Electrically Isolated
Feedback Device: NO FEEDBACK
Front Face Code: Standard
Front Shaft Indicator: None
Shaft Ground Indicator: No Shaft Grounding
Shaft Rotation: Reversible
Shaft Slinger Indicator: Shaft Slinger
Speed Code: Single Speed
Motor Standards: NEMA
Starting Method: Direct on line
Thermal Device - Bearing: None
Thermal Device - Winding: None
Vibration Sensor Indicator: No Vibration Sensor
Winding Thermal 1: None
Winding Thermal 2: None
Page 3 of 12
Page 4
Product Information Packet: CEWDM3558 - 2HP,1755RPM,3PH,60HZ,56C,3530M,TEFC,F1,N
Nameplate NP1669L
CAT.NO. CEWDM3558
SPEC. 35S587M494G1
HP 2
VOLTS 230/460
AMP 5.8/2.9
RPM 1755
FRAME 56C HZ 60 PH 3
SER.F. 1.15 CODE L DES B CLASS F
NEMA-NOM-EFF 86.5 PF 73
RATING 40C AMB-CONT
CC 010A USABLE AT 208V 6
DE 6205 ODE 6203
ENCL TEFC SN
BLANK
Page 4 of 12
Page 5
Product Information Packet: CEWDM3558 - 2HP,1755RPM,3PH,60HZ,56C,3530M,TEFC,F1,N
Parts List
Part Number Description Quantity
SA293876 SA 35S587M494G1 1.000 EA
RA279964 RA 35S587M494G1 1.000 EA
34FN3002B01 EXTERNAL FAN, PLASTIC, .637/.639 HUB W/ 1.000 EA
NS2512A01 INSULATOR, CONDUIT BOX X 1.000 EA
35GS1040 35 MOLDED GASKET W/LIP, LEAD SEAL, 1.000 EA
51XB1016A08 10-16X 1/2HXWSSLD SERTYB 2.000 EA
11XW1032G06 10-32 X .38, TAPTITE II, HEX WSHR SLTD U 1.000 EA
35EP3122B00W MASTER ODE,203 BRG,.683SH,.125NPT DRNS,F 1.000 EA
HW4072A01 BLACK DRAIN PLUG FOR .125 NPT 3.000 EA
HW5100A03 WAVY WASHER (W1543-017) 1.000 EA
HW4600B49 SEAL 0.938 X 1.624 X 0.250 SINGLE LIP DB 1.000 EA
35EP3307E00W MASTER DE,205 BRG,1.623SH,.125NPT DRNS,C 1.000 EA
12XN1032S20 10-32 X 1-1/4 HEX M.S. , STAINLESS STEEL 2.000 EA
HW4072A01 BLACK DRAIN PLUG FOR .125 NPT 3.000 EA
51XB1214A16 12-14X1.00 HXWSSLD SERTYB 1.000 EA
35FH4005A32SP IEC FH NO GRSR W/3 HOLES - PRIMED 1.000 EA
11XW1032S06 10-32 X .38, TAPTITE II, HEX WSHR SLTD U 3.000 EA
35GS1030A02 35 GS FOR CB LID - WHITE NEOPRENE 1.000 EA
59XW0832S07 TAPTITE II,HEX WSHR UNSLTD SER,410 S.S., 4.000 EA
HW1003S08 WASHER, #8 EX TH LK, SS 4.000 EA
HW4600B39SP V-RING SLINGER 0.550 X 0.790 X .18 VITON 1.000 EA
HW4600B46 V-RING SLINGER 0.875 X 1.420 X .24 VITON 1.000 EA
HW2502D13 SS KEY, 3/16 SQ X 1.375 1.000 EA
HA7000A04 KEY RETAINER 0.625 DIA SHAFTS 1.000 EA
Page 5 of 12
Page 6
Product Information Packet: CEWDM3558 - 2HP,1755RPM,3PH,60HZ,56C,3530M,TEFC,F1,N
Parts List (continued)
Part Number Description Quantity
MJ5001A27 32220KN GRAY SEALER *MIN BUY 4 QTS=1GAL 0.001 QT
85XU0407S04 4X1/4 U DRIVE PIN STAINLESS 2.000 EA
LB1164 LABEL,WARNING AND DRAIN 1.000 EA
HA5027A02 HA4054 T-DRAIN X2 BAGGED WITH LABEL 1.000 EA
35CB3008A01G SPL CONDUIT BOX, MACHINED GRAY 1.000 EA
MJ1000A02 GREASE, MOBIL POLYREX EM - 124047 0.050 LB
35CB4522 35 LIPPED CB LID PRIMED 1.000 EA
MG1025Z02 ACTIVATOR WILKOFAST 060.02HF 0.010 GA
MG1025W01 WILKOFAST, 781.01, SIGNAL WHITE #9003 0.017 GA
HA3100S09 THRUBOLT 9.25 LENGTH SS 4.000 EA
LC0005 CONN.DIA.,TY M,9-LD,DUAL VOLT,REVERSING 1.000 EA
NP1669L SS WD SUPER-E UL CSA-EEV PREM REV MTG 1.000 EA
36PA1000 PKG GRP, PRINT PK1016A06 1.000 EA
MN416A01 TAG-INSTAL-MAINT no wire (1200/bx) 3/19 1.000 EA
PE-0000002 ZRTG PE ASSEMBLY 1.000 EA
FE-0000001 ZRTG FE ASSEMBLY 1.000 EA
Page 6 of 12
Page 7
Product Information Packet: CEWDM3558 - 2HP,1755RPM,3PH,60HZ,56C,3530M,TEFC,F1,N
AC Induction Motor Performance Data
Record # 53333 - Typical performance - not guaranteed values
Winding: 35WGM494-R078 Type: 3530M Enclosure: TEFC
Nameplate Data
460 V, 60 Hz:
High Voltage Connection
Rated Output (HP) 2 Full Load Torque 5.99 LB-FT
Volts 230/460 Start Configuration direct on line
Full Load Amps 5.8/2.9 Breakdown Torque 23.9 LB-FT
R.P.M. 1755 Pull-up Torque 15.9 LB-FT
Hz 60 Phase 3 Locked-rotor Torque 18.1 LB-FT
NEMA Design Code B KVA Code L Starting Current 24.3 A
Service Factor (S.F.) 1.15 No-load Current 1.82 A
NEMA Nom. Eff. 86.5 Power Factor 73 LinelineRes.@25ºC 7.46Ω
Rating - Duty 40C AMB-CONT Temp. Rise @ Rated Load 61°C
S.F. Amps Temp. Rise @ S.F. Load 74°C
Locked-rotor Power Factor 50
Rotor inertia 0.177 LB-FT2
Load Characteristics 460 V, 60 Hz, 2 HP
% of Rated Load 25 50 75 100 125 150 S.F.
Power Factor 32 51 64 73 79 82 77
Efficiency 75.7 84.2 86.4 87.3 86.2 85.1 86.4
Speed 1788.5 1778 1766.7 1754.5 1740.8 1726.6 1746
Line amperes 1.92 2.17 2.51 2.94 3.46 4.01 3.25
Page 7 of 12
Page 8
Product Information Packet: CEWDM3558 - 2HP,1755RPM,3PH,60HZ,56C,3530M,TEFC,F1,N
Performance Graph at 460V, 60Hz, 2.0HP Typical performance - Not guaranteed values
Page 8 of 12
Page 9
Product Information Packet: CEWDM3558 - 2HP,1755RPM,3PH,60HZ,56C,3530M,TEFC,F1,N
AC Induction Motor Performance Data
Record # 64712 - Typical performance - not guaranteed values
Winding: 35WGM494-R078 Type: 3530M Enclosure: TEFC
Nameplate Data
230 V, 60 Hz:
Low Voltage Connection
Rated Output (HP) 2 Full Load Torque 5.99 LB-FT
Volts 230/460 Start Configuration direct on line
Full Load Amps 5.8/2.9 Breakdown Torque 23.9 LB-FT
R.P.M. 1755 Pull-up Torque 15.9 LB-FT
Hz 60 Phase 3 Locked-rotor Torque 18.1 LB-FT
NEMA Design Code B KVA Code L Starting Current 48.6 A
Service Factor (S.F.) 1.15 No-load Current 3.64 A
NEMA Nom. Eff. 86.5 Power Factor 73 LinelineRes.@25ºC 1.75Ω
Rating - Duty 40C AMB-CONT Temp. Rise @ Rated Load 61°C
S.F. Amps Temp. Rise @ S.F. Load 72°C
Locked-rotor Power Factor 50.1
Rotor inertia 0.177 LB-FT2
Load Characteristics 230 V, 60 Hz, 2 HP
% of Rated Load 25 50 75 100 125 150 S.F.
Power Factor 32 51 64 73 79 82 77
Efficiency 75.4 84 86.4 87.2 86.1 85 86.5
Speed 1789 1778 1767 1755 1741 1727 1747
Line amperes 3.84 4.34 5.02 5.88 6.92 8.02 6.5
Page 9 of 12
Page 10
Product Information Packet: CEWDM3558 - 2HP,1755RPM,3PH,60HZ,56C,3530M,TEFC,F1,N
Performance Graph at 230V, 60Hz, 2.0HP Typical performance - Not guaranteed values
Page 10 of 12
Page 11
Product Information Packet: CEWDM3558 - 2HP,1755RPM,3PH,60HZ,56C,3530M,TEFC,F1,N
6250
6245
4 500
4 497
6 49
2 06
1 88
13
510-520 = 12 22
521-528 = 13 22
529-535 = 14 10
536-546 = 15 47
3 00 2 75
66
4 32
3 75
7 19
FORSHEDA
SLINGER
(EACH END)
19 KEY
1 38 LONG
(4) 125 NPT HOLES
3 W/PLUGS
@ 3 9 & 11:00
(EACH END)
FORSHEDA
SLILNGER
NAMEPLATE
4 SLOTS
Ø 34
2 47 2 47
3 31
6 62
3 50
3 44
5 79
6 61
45°
45°
4 68
4 HOLES
38-16 TAP ON
Ø5 88 B C
LEAD HOLE
50 N P T
FRONT END DETAIL
PULLEY END DETAIL
OMIT LOCK-WASHERS &
APPLY SEALER UNDER
BEARING REATINER SCREW
HEADS & HOUSING O D
BEFORE PRESSING IN SEAL
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
35LYS587
B
STD HORZ 56C TEFC 35M WD (S/P #9)
SH 1 of 1
REV. DESC
REV
BY
REVISED
MODEL NO.
VERSION
TDR
REF
35LYS587
LOADING OF SWD DWG FOR 2D TO 3D CONVERSION - PKG12
ENALEM0
G
07 57 18 12/12/2018
-
000001093440
07
35LYS587
CUSTOMER IS RESPONSIBLE FOR DETERMINING THAT THE PRODUCT WILL PERFORM SUITABLY IN THE INTENDED APPLICATION
BALDOR - RELIANCE
®
Page 11 of 12
Page 12
Product Information Packet: CEWDM3558 - 2HP,1755RPM,3PH,60HZ,56C,3530M,TEFC,F1,N
Page 12 of 12
Loading...