Balboa Water Group ML700 Quick Reference

EL/GL Series - Mach 3

ML700 Quick Reference Guide

WarmTime

F1

F2

PL

TL

Cool

Mode/Prog

Initial Start-up

When your spa is first actuated, it will go into Priming mode
(after displaying some configuration information). Please

see the M-7 Installation Instruction Manual for complete
instructions on Power-up and Pump Priming.

The Priming mode will last for up to 4 minutes and then the
spa will begin to heat and maintain the water temperature
in the Standard mode. You can exit Priming mode early by
pressing “Warm” or “Cool.”

Light

Jets 1

Blower

Jets 2

Time

When time hasn’t been programmed, the “ ” icon
flashes. (Time settings on EL1000 and some EL2000 systems

are not preserved in the event of power loss; time will have to
be reprogrammed upon each power up.)

Setting the Time

Once the spa has been properly connected the first time (every power
up on the EL1000 and some EL2000 systems), notice the “ ” icon
appearing on the screen.

TimeTime

Press

Select

the hour by pressing

Press

Mode/ProgMode/Prog

Select

minutes by pressing

Press

Mode/ProgMode/Prog

Press

then

Mode/ProgMode/Prog

WarmWarm

Or

(Each press changes
the time by 1 minute)

CoolCool

to enter.

WarmWarm

Or

(Each press changes
the time by 1 minute)

CoolCool

to exit the time setting procedure and enter the
optional filter cycle programming. (Exits programming
on some EL1000 and some EL2000 systems.)

TimeTime

to exit programming.

Mode/Prog

This button is used to switch between standard, economy,
and sleep modes. Press “Mode/Prog” to enter mode
programming, press “Cool” to cycle through to desired mode
(LCD flashes until confirmed), then press “Mode/Prog” to
confirm selection.

Standard mode maintains the desired temperature. Note that
the last measured spa temperature displayed is current only
when the pump has been running for at least 1 minute. The
“ ” icon will display until the mode is changed.

Economy mode heats the spa to set temperature only during
filter cycles. The “ ” icon will display until mode is
changed. Pressing “Jets 1” while in Economy mode puts the
spa in Standard-In-Economy mode, which operates the same as
Standard Mode, then reverts to Economy Mode automatically
after 1 hour. Both the “ ” and “ ” icons
display in this mode. During this time, a press of the
“Mode/Prog” button will revert to Economy Mode immediately.

Sleep mode heats the spa to within 20°F (11°C) of the set
temperature only during filter cycles. The “ ” icon will
display until mode is changed.

Standby Mode

Pressing “Warm” or “Cool” then “Jets 2” will turn off all
spa functions temporarily. This is helpful when changing a
filter. Pressing any button resets the spa. On some systems
the “Jets 1” button will control the pump in Standby Mode
(“Drain Mode”). In this case, press any other button to exit.

Locking the Panel

Press “Time” “Jets 1” then “Warm” within 3 seconds. When
locked, the PL “

PL

” light will light. All buttons are frozen
except the “Time” button. To unlock the panel, press “Time”
“Jets 1” then “Cool.”

Locking the Set Temperature

Press “Warm” or “Cool” then “Time,” “Jets 1,” and “Warm”
within 3 seconds to activate the lock. The TL “

TL

” light will

light when the set temperature is locked.

To unlock the set temperature, press “Warm” or “Cool” then
“Time,” “Jets 1” and “Cool.”

Additional Features

Refer to your User Guide for additional details and features that
are available with your ML700 panel and EL/GL Series system.

900854

P/N 40520-80_B 06/14/2006

YXcYfX$`ejkild\ekj%Zfd