Baakkeerr
B
Web site: www.baker-online.com E-mail: info@baker-online.com
Phone: (573) 663 – 7711 Fax: (573) 663 – 2787
B//
BXX
B
B
Usseerr
U
Ellington Industrial Supply, Inc.
P. O. Box 128
Ellington, Missouri 63638 USA
Baanndd
B
Maannuuaall
M
Reessaa
R
w
w
TABLE OF CONTENTS
1 INTRODUCTION 3
Machine Purpose 3
Machine Function 3
Definition of Terms 4
Manual Contents Notice 5
Machine Specifications and Requirements 5
Warranty 6
Defective Parts 7
Service Policy 7
2 RULES FOR SAFE OPERATION 8
Safety Expectations for Operating Power Equipment 8
Control of Hazardous Energy – (Lockout / Tagout) 9
3 MACHINE FEATURES 10
4 SET-UP 11
Receiving and Inspection 11
Unpacking 11
Machine Moving 11
Machine Positioning 11
Power and Utilities Requirements 11
Operator Training 12
5 CHANGING BLADES 13
Removing Blade 13
Installing New Blade 13
Blade Tracking 14
Checking the Tracking 14
Drive Wheel Adjustments 15
Idler Wheel Adjustments 15
Vertical Adjustments 15
Horizontal Adjustments 16
Cutting Angle Adjustments 17
Determining the Problems 17
Front-to-Back Adjustments 18
Side-to-Side Adjustments 18
6 SETTING GUIDES 19-20
7 FEEDWORKS 21
Feed Speed 21
Hydraulics 21
Conveyor Belts 21
Powered Hold-Down 22
8 OPTIONAL EQUIPMENT 23
BLADES 23
9 MAINTENANCE TASK CHECKLIST 24
Trouble Shooting 25
Parts and Service 26
Recommended Spare Parts 26
Service Contact Information 26
Serial Number Location 26
10 Wiring Diagrams 27-28
Baker Band Resaw - Rev 1, 09/08; WWW.BAKER-ONLINE.COM
2
INTRODUCTION
Thank you and congratulations on the purchase of your new Baker B/BX Band Resaw. It
has been designed to be durable, productive and easy to use. When properly ran and
maintained, it will provide you with many years of profitable operation.
For safety reasons, and for your own best use of the Baker B/BX Band Resaw, we insist
that you read this manual fully, and constantly review and refer back to it as necessary.
No one should attempt to operate or perform maintenance on this equipment until they have
been trained and taken the time to read and understand the information contained in this
manual.
** FAILING TO DO SO MAY RESULT IN SERIOUS INJURY **
Machine Purpose
The Baker B/BX Band Resaw was designed to have a two point feed works allowing for
running random width materials. The head rig can be adjusted up or down while the conveyor
stays at a fixed height making it easier to interchange and integrate with other material
handling systems.
Machine Function
The Baker B Band Resaw is equipped with a 20 HP electric motor and accepts material up
to 6” x 12” (15 cm x 30 cm) and uses a 6” wide conveyor while the Baker BX is equipped with
a 30 HP electric motor and accepts material up to 12” x 12” (30 cm x 30 cm) with a 12”
conveyor. Both models are capable of variable speeds from 20-120 feet per minute as well as
Baker’s exclusive guide system that includes guide plates and guide roller.
Baker Band Resaw - Rev 1, 09/08; WWW.BAKER-ONLINE.COM
3
Definition of Terms
All Stop
Band Saw
Board Foot or
Board Feet
Cant
Cant Hook
Carriage
CFM (cubic feet
per minute)
Edge Guide
Edger
End Stop
Fence (Arm)
Flitch
Head Rig or
Head Saw
Safety button (typically “red”) designed to immediately shut-down machine operation
A saw consisting of a continuous piece of flexible steel, with teeth on one side
A form of measurement where one board foot equals the volume of a board 1 inch thick by 12
inches wide and 12 inches long
The 3 or 4 sided timber left over from a log, normally the center or core of the log
A device used for rolling cants or logs
A framework on wheels that allows movement of a log back and forth past the saw blade
A measure of the volume of a substance flowing through air within a fixed period of time
A straight edge that is used to guide a 3-sided flitch along a piece of material
A sawmill machine used to remove wany edges from flitches after they come off the head rig,
squaring the edges and ripping the flitch into lumber
A mechanism designed to stop the progress of an off-loading board
A straight guide used to keep a log, cant or board a set distance from a blade or cutter
A longitudinal section of a log with wany edges
The principle support structures on a sawmill that carries the engin e, wheels and band blade used
for the initial breakdown of a log
Kerf
Lift Point
Live Rollers
Lockout /
Tagout
Lumber
Off-load
Production
Rate
Roll-case
Slab
Thin Kerf
Wany
The groove or thickness of the path cut by the saw teeth; the total amount of sawdust removed
during a single cut
A point where pressure can and should be applied for lifting
A powered roll case that mechanically moves material
Requires authorized employee(s) to lock and tag the energy-isolating device(s) to prevent the
release of hazardous energy in order to prevent injury to employees, normally while performing
maintenance or repairs
A longitudinal section of a log after the wany edges have been removed, normally a 4-sided
rectangular shaped piece
The side of a machine where the work piece (slab, cant, board, etc.) exits
A produced or processed quantity measure with respect to another measured quantity of time; for
example number of boards per minute
A mechanical apparatus with elongated cylinders used to perform rolling operation for material
movement, can be both powered and/or manually operated
The exterior portion of a log removed by the saw, having one flat and one rounded portion of a log
A relative term, typically referencing band saw blades which are usually thinner than circular saw
blades thus resulting in greater lumber recovery
Waning or diminished in some parts; not of uniform size throughout; sawed boa rds or timber that is
tapered or uneven, from being cut too near the outside of the log
Yield
To generate a return for effort, an amount produced
Baker Band Resaw - Rev 1, 09/08; WWW.BAKER-ONLINE.COM
4
Manual Contents Notice
This manual is not totally comprehensive. It does not and cannot convey every
possible safety and operational problem that may arise while using this machine. The
manual will cover many of the basic and specific safety procedures needed in an
industrial environment.
All federal and state laws and any regulations having jurisdiction covering the safety
requirements for use of this machine take precedence over the statements in this
manual. Users of this machine must adhere to such regulations.
Machine Specifications and Requirements
Power:
B = 20HP TEFC
BX = 30HP TEFC
Feedworks/Conveyor Motor:
Driven by main engine
Capacities:
B = 6” x 12”; 6”; wide conveyor
BX = 12” x 12”; 12” wide conveyor
Feed Speed: 20 –120 feet per minute
Both B and BX models
Dimensions &
Weight:
Length: 180
in(Add 55” for
each added head)
Width: 77 in(B)
85” (BX)
Height: 68 in
Weight: B - 2,800
lbs (Add 1,300 lbs
per added head)
BX – 3,800 lbs
(Add 1,800 lbs per
added head)
Band Blades:
B = 0.0035” x 1” x 13’2” hardback or
0.035” x 1 ¼” x 13’2 hardback
BX = 0.0035” x 1” x 14’2” hardback or
0.035” x 1 ¼” x 14’2 hardback
Kerf: 0.072”
Band Wheels:
28 in diameter; all-steel with crown
Sawdust Removal:
4” outlet; min. 600 CFM suction
recommended at dust removal chute
Baker Band Resaw - Rev 1, 09/08; WWW.BAKER-ONLINE.COM
5
Warranty
Ellington Industrial Supply, Inc. machinery is warranted against defects in material or
workmanship starting from the date of shipment from the manufacturing plant.
This warranty is given solely to the “original purchaser” of the equipment and is in no
way to be expressed or implied that it is transferable to any other parties without the
written consent and approval from the CEO or Sales Manager of Baker Products.
Our one (1) year warranty period covers all items built at our manufacturing facilities
including structural frame, cowlings, doors, shafting, dust chutes and guards.
We honor six (6) months of warranty coverage for miscellaneous vendor-purchasedsupplied items including bearings, chain, sprockets, hydraulic components, etc.
Ninety (90) days of warranty coverage is provided on all electrical parts. All electrical
components and wiring has been installed in accordance with the National Electrical
Code (NEC) of the United States of America.
Ellington Industrial Supply, Inc. does not warranty this machine to meet any other
requirements or jurisdiction of any electrical or safety codes of any other state,
municipality, other country or jurisdiction The purchaser assumes all risk and liability
whatsoever resulting from the use thereof whether used singularly or in conjunction with
other machinery or apparatus, including, but not limited to, all matters resulting from
sawdust generation.
Note: No warranty is provided on any electrical components or parts if equipment is
powered or connected to a roto-phase electrical converter in order to create a three
phase power supply for operational current from a single phase source.
Any change in materials, design, or performance intended to improve any product of
Ellington Industrial Supply, Inc. shall not obligate Ellington Industrial Supply, Inc. to
modify any previously manufactured equipment.
This manual may contain details that if not properly followed can affect the performance
of your equipment. You are responsible for proper use and maintenance of your
equipment and we reserve the right to deny warranty work if deemed to be caused by a
lack of proper maintenance or negligence by the owner or any of their employees.
Baker Band Resaw - Rev 1, 09/08; WWW.BAKER-ONLINE.COM
6
Defective Parts
Parts claimed defective must be returned freight prepaid, to our plant in Ellington,
Missouri. Any part determined defective due to faulty workmanship or materials will be
replaced or repaired (at our option) free of charge, F.O.B. our plant. This warranty does
not cover expendable items (i.e. drive belts, band wheels, conveyor belting, blades,
cutters, guides, etc.). Except as expressly provided herein, this warranty is in lieu of all
other warranties, expressed or implied, including a warranty of merchantability or fitness
for a particular purpose. This warranty is “void” if any part of the unit has been tampered
with, modified, altered, or operated with parts other than supplied or recommended by
Ellington Industrial Supply, Inc. In no event shall Ellington Industrial Supply, Inc. be
liable for special, indirect, incidental or consequential damages, however arising,
including but not limited to, the loss of earnings or the cost of downtime.
Service Policy
In the event that you have any problems, call us at (573) 663-7711 any time between
8:00 AM and 5:00 PM (CST), Monday through Friday. A member of our trained staff will
answer any questions you may have. We charge nothing for this service.
The only charge is for replacement parts not covered by warranty or after our inspection
we deem that the problem is due to operator error or lack of proper maintenance or
neglect.
If it is necessary for a member of our service department to visit your plant at your
request, there will be a charge for this service. Call our service department for current
prices.
Retain this Information for your Records
Model Number: ………………………………………...………………………….
Serial Number: …………………………………………………………………….
Date of Purchase: …………………………………………………………………
Power Source:…………..…………………….……………………………………
Dust Removal: ….……………………………………………………………….…
Web site: www.baker-online.com E-mail: info@baker-online.com
Phone: (573) 663 – 7711 Fax: (573) 663 – 2787
Baker Band Resaw - Rev 1, 09/08; WWW.BAKER-ONLINE.COM
Ellington Industrial Supply, Inc.
P. O. Box 128
Ellington, Missouri 63638 USA
7
or deat
RULES FOR SAFE OPERATION
The purpose of safety symbols and signage is to draw your attention to real or possible
hazardous conditions that may exist when operating this equipment. Please remember that
safety symbols and signage alone do not eliminate danger and are not substitute for proper
training and education regarding operational hazards.
SAFETY EXPECTATIONS FOR OPERATING POWER EQUIPMENT
ALWAYS…
ENSURE THAT TRAINED PERSONNEL OPERATE, MAINTAIN AND REPAIR THIS EQUIPMENT
TURN
KEEP WORK AREA CLEAN AND WELL LIGHTED TO MINIMIZE OR ELIMINATE HAZARDS
KEEP
OPERATE
KEEP
REMOVE
USE
WEAR
NEVER…
LEAVE MACHINERY RUNNING OR UNATTENDED, ALWAYS TURN POWER OFF
OPERATE
POWER OFF AND LOCKOUT / TAGOUT PRIOR TO PERFORMING MAINTENANCE
CHILDREN AND VISITIORS AWAY FROM OPERATING EQUIPMENT
THE EQUIPMENT AT THE RATE IT WAS DESIGNED FOR
GUARDS IN PLACE WHEN OPERATING EQUIPMENT
TOOLS BEFORE RESUMING OPERATION
PROPER EXTENSION CORD
PROPER APPAREL AND AVOID LOOSE CLOTHING AND ACCESSORIES THAT COULD GET
CAUGHT IN MOVING PARTS
ALWAYS WEAR SAFETY GLASSES AND HEARING PROTECTION
AVOID “KICK-BACK” BY KNOWING WHAT CONDITIONS CAN CREATE IT
CHECK DAMAGED PARTS AND REPAIR OR REPLACE THEM IMMEDIATELY
EQUIPMENT WHEN TIRED, FATIGUED OR UNDER THE INFLUENCE OF DRUGS OR
ALCOHOL
ALLOW UNTRAINED PERSONNEL TO OPERATE, MAINTAIN OR REPAIR THIS EQUIPMENT
This symbol and warning indicates a potentially hazardous
situation, which, if not avoided, will result in death or serious injury.
This symbol and warning indicates a potentially hazardous
situation, which, if not avoided, could result in death or serious
injury.
This symbol and warning indicates a potentially hazardous
situation, which, if not avoided, may result in minor or moderate
injury.
This warning provides notice and instruction regarding a potentially
hazardous situation, which, if not avoided will result in serious injury
h.
No list of safety expectations can ever be complete as every work environment is as different
as are the people operating the equipment.
Always keep safety as your highest priority and always use this machine with caution and
respect.
Baker Band Resaw - Rev 1, 09/08; WWW.BAKER-ONLINE.COM
8
Control of Hazardous Energy – (Lockout / Tagout)
Lockout / Tagout (LOTO) refers to specific practices and procedures to safeguard employees
from the unexpected energy, startup of machinery/equipment, or the release of hazardous
energy during service or maintenance activities.
This requires that a designated individual turn off and disconnect the machinery/equipment
from its energy source(s) before performing service or maintenance and that the authorized
employee(s) lock and tag the energy-isolating device(s) to prevent the release of hazardous
energy and take steps to verify that the energy has been isolated effectively.
List of Related Terms
Affected
Employee
Authorized
Employee
Energy
Source
Lockout
Servicing
and / or
Maintenance
Tagout
Example of lockout tags, lockout
hasp and keyed lock
An employee whose job requires them to operate a machine or piece of
equipment on which service or maintenance is being performed.
A person who locks or implements a tagout system procedure on machines
or equipment to perform service or maintenance on that machine or
equipment. An authorized employee and an affected employee may be the
same person when the affected employee's duties also include performing
service or maintenance.
Any source of electrical, mechanical, hydraulic, pneumatic, chemical, thermal,
or other energy.
The placement of a lockout device (such as a lock) on an energy-isolating
device, in accordance with an established procedure that ensures the device
and the equipment cannot be operated until the lockout device is removed.
Workplace activities such as constructing, installing, setting up, adjusting,
inspecting, modifying, maintaining or servicing machines or equipment.
These activities include lubrication, cleaning or un-jamming of machines or
equipment, and making adjustments or tool changes where the employee
may be exposed to the unexpected energy, start-up of equipment or release
of hazardous energy.
The placement of a tagout device (such as a tag) on an energy-isolating
device, in accordance with an established procedure that ensures the device
and the equipment may not be operated until the tagout device is removed.
The Fatal Five Main Causes of
Lockout/Tagout Injuries
1. Failure to stop equipment
2. Failure to disconnect from a
power source
3. Failure to dissipate (bleed,
neutralize) residual energy
4. Accidental re-starting of
equipment
5. Failure to clear work areas
before re-starting
Baker Band Resaw - Rev 1, 09/08; WWW.BAKER-ONLINE.COM
9
MACHINE FEATURES
We want to highlight the unique and special features of the Baker B/BX Band Resaw.
Cowling Handle
Blade Tensioning
T-handle
Adjustable
Head Rig
Head Rig and
Cowling Door
15’
Powered Hold Down
Dust Chute
Hydraulic
Powered
Variable Speed
Conveyor
6’ – 5”
Footprint : B Model
single shown
Baker Band Resaw - Rev 1, 09/08; WWW.BAKER-ONLINE.COM
10
SET-UP
Receiving and Inspection
Upon receipt and prior to signing transport carrier’s documents, conduct a walk-around
and visual inspection of your new equipment. Note any damage in writing upon the
carrier’s bill of lading and contact us immediately.
Note: All new equipment is assembled and thoroughly tested prior to shipment, however
damage may occur during transit, which could cause the machine to not operate correctly
during start-up.
Unpacking
If machine was delivered via flatbed trailer, remove straps or chains securing it in place.
If machine was delivered by crate, carefully remove upper crating materials from the base
skid.
Remove lag screws, strapping, etc. that attaches the machine to the skid.
Machine Moving
Lift machine at the indicated lift points only.
o Use a safety strap to avoid tip-over.
Transport machine to the installation site.
Machine Positioning (Placement, Leveling, Alignment)
For optimum performance, designate a solid and level foundation that is covered and dry,
free of environmental elements such as rain or snow that could cause electrical or slip
hazards.
Provide a minimum of 3 feet of clear workspace in front of the electrical panel.
Provide a minimum of 15 feet of clear workspace in front of in-feed and off-load areas.
Power and Utilities Requirements
For safe and effective operation confirm your incoming voltage and available
amperage is equal to what the machine has been wired for at the factory.
A qualified electrician should complete electrical connections and check
for correct motor directional rotation.
Ensure all wiring and electrical connections are located in a safe position and away
from any hazardous conditions.
Efficient dust and chip removal requires a minimum of 500 CFM suction at the
machine dust removal chute. This is an employer/owner responsibility.
Baker Band Resaw - Rev 1, 09/08; WWW.BAKER-ONLINE.COM
11
Operator Training
According to many OSHA, ANSI, STATE, and LOCAL CODES, it is the EMPLOYER’S
RESPONSIBILITY to:
Permit only trained and authorized employees to operate and maintain
equipment.
Inspect and maintain guards, safety devices and start/stop controls.
Instruct, train and supervise the safe method of work.
Be sure personnel are properly trained and safety rules are clearly understood before
operating or performing maintenance.
Operator
Machine
Guards
Devices
Instructions
All of these together make up the safety system.
Failure of any one of these factors will increase
accident potential.
FFRREEEE TTRRAAIINNIINNGG OONN PPRROOPPEERR SSEETT--UUPP AANNDD
OOPPEERRAATTIIOONN IISS AAVVAAIILLAABBLLEE OONN SSIITTEE AATT
TTHHEE MMAANNUUFFAACCTTUURREERR’’SS FFAACCIILLIITTYY
Baker Band Resaw - Rev 1, 09/08; WWW.BAKER-ONLINE.COM
12
CHANGING BLADES
Removing Blade
Turn power off, allow machine to come to a complete stop, then perform lockout / tagout
before proceeding.
Use handle on left side of the head rig to lift door until it lies securely over the top of the
head rig. Never open head rig door with blade in motion.
Loosen spring tensioning by turning the T-handle counter-clockwise.
Pull down on blade at the top, between the wheels, with your right hand while pushing the
top of the left wheel away from you until the left wheel moves. If the blade broke, push the
top of the left wheel back with your left hand and pull the wheel toward the right wheel
with your right hand.
Blade should be loose enough to be removed. Push blade back and off of the right wheel.
Pull blade out of guides and remove. If blade is not loose enough to remove from right
wheel, go back to the 3rd checklist item above and follow the process again.
Installing New Blade
Put blade over the right wheel, through the guides and over the left wheel with teeth
facing forward. Be sure the points of the teeth are aimed to the right (toward the dust
chute) as they pass through the guides.
Note: It may be necessary to turn the blade inside out.
Make sure the blade gullet is flush with the face of the wheel to avoid knocking out the
set.
Turn the spring tensioning T-handle clockwise until one of the spacers makes contact with
both compression plates.
Manually turn the wheels to be sure blade is tracking properly.
Close door.
T-Handle
Spacers
Figure A: Blade
Tensioning T-Handle
Baker Band Resaw - Rev 1, 09/08; WWW.BAKER-ONLINE.COM
13
Compression
Plates
Blade Tracking
The blade must be installed and properly tensioned (see “Changing Blades”) before
beginning this procedure. Guides should be in a position where they are just barely touching
the blade.
The blade tracking is properly set in the factory. It may occasionally be knocked out. This
should explain how to check and reset it.
Checking the Tracking
Rotate the idler wheel several rotations counterclockwise. Examine the position of the back
of the blade on the wheel at the top of the wheel and compare it to its position at the bottom
of the wheel. The blade position should be the same in both locations, on both idler and pull
wheels. If not, the tracking should be adjusted.
If tracking appears to be correct after the above procedure, your saw will cut without
problems due to blade tracking. However, now rotate the idler wheel several rotations
clockwise. Check the blade in the same way as above. If the blade does not track properly
“backward” then you may experience hard-to-identify problems, which may limit your saw’s
capabilities. In this case, it is advisable to adjust the tracking using the following procedures.
An important starting point for proper tracking is to ensure the face of the wheels align with
one another. This can be checked with a straightedge. Use this method to start setting the
tracking using the adjusters shown in the illustration below.
All adjustments for blade tracking are located on the backside (motor side) of the head rig on
the square tube with the spring tensioning assembly located on one end.
Vertical
Adjuster Bolt
Setscrew
Baker Band Resaw - Rev 1, 09/08; WWW.BAKER-ONLINE.COM
Horizontal
Adjuster Bolt
Figure B: Back View with
Motor Removed
14
Drive Wheel Adjustments
The drive wheel’s position is set in the factory. In most cases it never needs to be moved. It
can only be moved in and out, and should only be moved when the wheel is cocked so that
the face cannot be lined up with the face of the idler wheel. If you find that you must move
this wheel, you will find a set screw located under the rubber dust cap, on top of the square
tube, on the back side of the head rig, directly behind the wheel. With this setscrew
loosened, the wheel can be moved in or out, or removed completely. If spindle and wheel
assembly is moved, the spindle will need to be re-dimpled. Retighten setscrew when
finished.
Note: It is important to re-dimple the spindle after moving or replacing it.
Idler Wheel Adjustments
When looking at the front of the head rig, the idler wheel is on the left. This wheel is used to
adjust tracking problems. Your tracking adjusters are located on the square tube on the
backside of the head rig. These two bolts make all of your tracking adjustments. The bolt on
the topside of the square tube is used for vertical adjustments. The bolt on the backside of
the square tube underneath the motor is used for horizontal adjustments. Use these bolts to
tilt the idler wheel so that it is lined up with the face of the drive wheel. When the faces
appear to be lined up, fine-tune it using the following procedure.
Vertical Adjustments
Rotate the wheel several rotations counterclockwise.
Examine the positions of the back of the blade on the
wheel at the top of the wheel and compare it to its
position at the bottom of the wheel. The blade position
should be the same in both locations on both wheels. If
not, proceed to the next step.
If the blade needs to come forward at the top of the
wheel, turn the vertical adjuster bolt clockwise. If the
blade needs to go back at the top of the wheel, loosen
lock nut then turn the vertical adjuster bolt
counterclockwise.
Manually turn the wheel several rotations and check the
tracking as noted in the first step above. If vertical
tracking is still not correct, repeat the procedure until the
blade position at the top and bottom of the wheel is the
same (both idler and pull wheels).
Rotate the wheel several rotations clockwise and repeat
the procedure, then tighten lock nut.
Note: When blade is tracking properly, the blade gullet
should be flush with the front side of the wheels.
Vertical
Adjuster
Bolt
Baker Band Resaw - Rev 1, 09/08; WWW.BAKER-ONLINE.COM
Figure C: Vertical View
with Covering Removed
15
Horizontal Adjustments
With the vertical alignment set correctly, compare the blade’s position at the top and
bottom to its position on the left side of the wheel. If it is not the same, proceed to the
next step.
If the left side of the wheel needs to go “back,” turn the horizontal adjuster bolt clockwise.
If the left side of the wheel needs to come forward, turn the horizontal adjuster bolt
counter-clockwise.
Of course, you’ll need to loosen the lock nut first. And, don’t forget to retighten the lock
nut when finished adjusting.
Manually turn the wheel several rotations counterclockwise and check the tracking as in
first step above. If horizontal tracking is still not correct, repeat procedure until blade
position on the left side of wheel is the same as the top and bottom. Do the same after
rotating the wheel clockwise.
Horizontal Adjuster Bolt
Figure D: Top View of Idler Wheel with Cover
Removed
Effect of Horizontal Adjuster
Baker Band Resaw - Rev 1, 09/08; WWW.BAKER-ONLINE.COM
16
Cutting Angle Adjustments
If your Baker starts producing boards that are not square, your cutting angle may need to be
adjusted. Before proceeding, though, make sure your guides are set properly (see “Setting
Guides”) and your blade tracking is correct (see “Blade Tracking”).
Check the conveyor belt and look for an obstruction that may be caught underneath the belt.
If everything listed above is okay, then continue.
Determining the Problem
Start by moving the guides away from the blade. The guides should not be touching the
blade in any way.
Get two metal plates of the same thickness, approximately ½” x 6” x 4”.
With the machine off, locked out and tagged out, place one of the metal plates on the
conveyor about 5 inches in front of
the blade and the other about 5
inches behind the blade. Set the
blade height to the thickness of the
metal plates.
Use a straight edge to lie across
the metal plates and over the
blade. Be sure the straight edge is
between the teeth, because the set
will give you inaccurate
measurements.
Using this method, you will easily
be able to determine if the front of
the blade is tilted up or down.
If the blade is tilted in this manner,
the cutting angle needs front-to-
back adjustment. Always make the
front-to-back adjustments
first.
To determine whether a side-
to-side adjustment is
necessary, measure the
distance from the blade to the
main conveyor beam at the
right and the left of the
conveyor . Both distances
should be identical. If not,
make a side-to-side
adjustment.
Figure F: Determining whether Side-to-Side
Figure E: Determining whether Front-to-
Back Adjustment is Necessary
Blade should be 1/32” higher in front
Adjustment is Necessary
Baker Band Resaw - Rev 1, 09/08; WWW.BAKER-ONLINE.COM
17
Front-to-Back Adjustments
The head is leveled at the factory. It is leveled so that the front of the blade is 1/32” higher
than the back. If there is ever a need to adjust this setting, it should be very minor.
If you must make these adjustments, the front-to-back adjusters are located below the head
rig. They are turnbuckles between the lift arms on both sides of the head rig.
Loosen the lock nuts at the end of the turnbuckles and use them to adjust your front-to-
back setting.
Side-to-Side Adjustments
To cut quality lumber, the blade must run parallel to the conveyor. This is preset at the
factory. However, if it ever gets knocked out, your Baker B/BX is set up so that the side-toside cutting angle can be fine tuned. This can be done with head rig adjustments.
Find the front turnbuckle that sits under the front lift arm (there is one on each side).
These are your side-to-side adjusters.
Raise or lower the side you are adjusting until the blade is level or at the desired angle.
Note: Whatever you do to one side, must be done “opposite” on the other side.
Side-to-Side Adjuster Front-to-Back Adjuster
Baker Band Resaw - Rev 1, 09/08; WWW.BAKER-ONLINE.COM
Figure G: Head Rig Adjusters
18
SETTING GUIDES
Important: Always make sure blade tracking and cutting angle are set properly before
adjusting guides.
Turn off power and perform lockout / tagout.
Adjust guides so that the distance between them is as little as your wood will allow. For
example, if you are cutting 6” material, set your guides at 6 1/2” to allow for clearance.
Move left guide after loosening the bolt on the backside of the head rig.
Loosen Upper Guide Plate Bolt and raise Upper Guide Plate up to highest point.
Retighten Upper Guide Plate Bolt.
Loosen the up & down positioning bolts on the back of guide brackets to position the
lower plate so that it is lightly touching the blade but not deflecting it. Also, tilt the Guide
Block so that it runs parallel to the blade. Retighten up & down positioning bolts.
Level the guides (on the front to back plane) to the conveyor with the two Tilt Adjusters on
the top of each guide arm after loosening the large tilt lockdown bolt. Place the 6” mark of
a 12” ruler in the middle of the blade between the blade teeth in the direction of the
conveyor. By using the front edge of the guide block as a reference, set this surface at a
right angle to the conveyor. Use this to make sure the blade is running parallel to the
conveyor. When set properly, lock down the Tilt Adjusters and retighten tilt lockdown bolt.
Loosen the front-to-back positioning bolts on the guide brackets to bring the front of the
guide plates slightly behind the back of the blade gullet. Retighten front-to-back
positioning bolts while holding down on the guide so that it is as low as the slot will allow.
Loosen the guide wheel bolt and turn the shaft of the guide wheel using the slot at the top
of the guide until the wheel is about 1/32” from the back of the blade. Retighten the guide
wheel bolt. This prohibits the blade from being pushed back far enough that the guide
plates knock the set out of the blade teeth.
Loosen upper guide positioning bolt and move the Upper Guide Plates down to just
slightly touch the blade and retighten upper guide positioning bolt.
Be sure the blade passes freely through the guides but does not move up and down.
Remove the dust elbow and look into the dust shoot to make sure that the blade runs
perfectly straight from one wheel to the other with no deflections due to the blade guides.
Also, make sure the position and angle of the guides are identical while looking into the
dust shoot.
Guide Illustrations on the Next Page
Baker Band Resaw - Rev 1, 09/08; WWW.BAKER-ONLINE.COM
19
SETTING GUIDES (continued)
The guide wheels are designed for up and down adjustment, so when a groove is worn, you
can move it so that it will wear in a different location. As the guide plates wear, they should be
moved closer together so that they do not allow the blade to move up and down. The plates
should be as tight on the blade as possible without inhibiting the blades movement.
Eventually, you will have to replace worn guide wheels and plates. You should always keep
spare guide wheels and plates on hand. Under normal use, guide plates should last about 6
months if they are set properly. If your guide plates are lasting significantly less than this, you
probably do not have your guides adjusted properly.
Tilt Adjusters
Lockdown Bolt
Up & Down
Positioning Bolts
Guide Bracket
Figure H: Back of Guides
Front-to-Back
Positioning Bolt
Guide Wheel
Bolt
Guide Wheel
Lower Guide Plate Upper Guide Plate
Baker Band Resaw - Rev 1, 09/08; WWW.BAKER-ONLINE.COM
Guide Block
Upper Guide
Plate Bolt
Figure I: Front of Guides
20
FEEDWORKS
Feed Speed
When the Feedworks Start/Stop Knob is pushed down, the Feedworks is stopped. To start
the Feedworks, pull the knob up.
Note: Always make sure the Feedworks Start/Stop Knob is down (off) when starting the saw.
The feed speed can be adjusted from 0 to 95
feet per minute with the Feed Speed Control
Arm located on the backside of the head rig.
When the arm is pointed down, the
Feedworks should be motionless. As you
swing the arm up, the feed speed will
increase. The arm can be locked into place
with the knob located on the arm. Make sure
this knob is loosened when you wish to move
the arm. You will want to experiment to find
the best speed to run your wood types.
Hydraulic Fluid
Reservoir
Hydraulics
The Feedworks uses a hydraulic pump driven off of the main drive motor. Dextron II
Transmission fluid is recommended.
Conveyor Belts
If the conveyor belts ever need to be adjusted or replaced, use the belt extenders on the infeed end of the machine. Each conveyor has two belt extenders on the in-feed end (one on
each side). These should be used to tighten or loosen the belt conveyor.
These adjustments should also be used to align the belt. With the Feedworks empty and in
motion, adjust one side until the belt is tracking perfectly.
Feed Speed
Control Arm
Hydraulic
Fluid Filter
Feedworks
Start/Stop
Figure J: Feedworks Assembly
Loosen locking bolts to
allow for adjustments
Re-tighten when finished
Figure K: Conveyor Belt Adjuster Arm (one on each side)
Baker Band Resaw - Rev 1, 09/08; WWW.BAKER-ONLINE.COM
Turn indexer nut to tighten
belt or adjust belt tracking
21
Powered Hold-Down
The Baker B/BX is equipped with powered hold-down that holds the wood in place while it is
being cut. It can be placed closer to or further away from the blade by loosening the (2) frontto-back bolts on top of the hold-down assembly.
Another (2) bolts on the front of the assembly allow the hold-down to move from side to side
or be completely removed.
Front-to-Back Bolts
Side-to-Side Bolts
Baker Band Resaw - Rev 1, 09/08; WWW.BAKER-ONLINE.COM
Figure L: Powered Hold-Down
22
OPTIONAL EQUIPMENT
Simple Slide Return Options
If you did not order a return conveyor but wish to add it now, simply call and order it, then
follow these directions for installing it:
Drain the fluid from the Baker B/BX into a clean reservoir so it can be reused.
Position the Return Conveyor and thread the supplied bolts into the side of the conveyor
and through the holes on the side of the Baker B/BX. Put the nuts on the exposed end of
the bolts and tighten.
Connect the hydraulic motor to the Feedworks Start/Stop Assembly with the supplied
hoses.
Tie up the hoses so that they are out of the way.
Refill the tank with hydraulic fluid.
Run the saw.
BLADES
The standard Baker B uses the following blades:
13’ – 2” x 1” x .035 2T Woodmaster C Band Blades
The standard Baker BX uses the following blades:
14’ – 2” x 1” x .035 2T Woodmaster C Band Blades
14’ – 2” x 1” x .035 also available
NOTE: 1-1/4” guide plates as well as other blade widths, thickness and tooth spacing are
available upon request.
Ask your sales consultant or the customer service department for details.
Blade usage is approximately two blades per day per head during full production. Use this
figure when ordering your blades until you have developed some record of blade usage for
your operation.
Using high quality blades is an important factor in achieving the highest performance out of
your Baker B/BX band resaw. Our machines are tested and set-up using Lenox blades
sold by Ellington Industrial Supply. These are very good blades for use on the Baker and
come highly recommended by the majority of Baker owners. If you would like more
information on these blades, contact:
Customer Service Department
Ellington Industrial Supply Co., Inc.
PO Box 128
Ellington, MO 63638 USA
Tel: (573) 663-7711
Fax: (573) 663-2787
Baker Band Resaw - Rev 1, 09/08; WWW.BAKER-ONLINE.COM
23
MAINTENANCE TASKS AND CHECKLIST
Note: Follow Lockout / Tagout prior to performing any checks or maintenance.
Daily
Use an air-hose to blow-off the dust and wood chips that accumulate in and around the
machine, especially the wheels.
Check band blade tracking
Check head rig v-belts
Check guides for adjustment
Check proper conveyor belt tracking
Note: The machine operator is closer to the operating mechanism of the machine during
clean up than during production – extra care should be taken.
Do NOT clean with flammable or combustible materials.
Follow applicable codes and standards with regards to:
o Ventilation and monitoring of work area for excessive accumulation of
hazardous vapors
o Wearing personal protective equipment for handling materials
o Using proper procedure for disposing of all waste materials
Weekly
Check chain works and tighten as needed and lubricate with grease
Check for worn master links
Check all setscrews
Monthly
Grease slow moving bearings
Check hydraulic motors and hoses for leaks due to wear or cracks
Every 3 Months
Motors should be greased with one pump of grease from a grease gun
Once a Year
Check 28” wheel bearings for any wear replace if worn.
Check crown of 28” wheel for wear. Re-crown or replace if needed.
Baker Band Resaw - Rev 1, 09/08; WWW.BAKER-ONLINE.COM
24
TROUBLE SHOOTING
Note: Always check blade tension, blade quality, and guides before attempting any other
adjustments. Always keep a blade on hand that you know cuts well. Put this blade on the
machine to make sure the problem isn’t the blade.
Boards that look like the image below usually occur after you wreck the saw. A hard piece
that accidentally gets hung up in the saw messes up your guide alignment. See “Setting
Guides”. A last alternative would be adjusting the head rigs. See “Cutting Angle
Adjustment”.
Boards that look like the image below are almost always problems with the blade. A blade
with more set on the top or with dull bottom teeth will cut bowed boards. Check with a good
blade. If it is not the blade, check blade tension.
Boards that look like the image below are usually blade problems. Ripples form when the
blade has more set on the bottom. Check with a good blade. If it is not the blade, check blade
tension.
Loose guide plates or improper blade tensioning can generally cause boards to look like the
image below. (See “Changing Blades” or “Setting Guides”). These boards can also result
from extreme damage to the tilt of the holdover wheels.
Baker Band Resaw - Rev 1, 09/08; WWW.BAKER-ONLINE.COM
25
Parts and Service
Recommended Spare Parts List
Part No. Description
141003
1” Top Guide Pad – QTY (2)
Part No. Description
141013 1 ¼” Top Guide Pad – QTY (2)
141004
141005
121006
141001
101275
181015
1” Bottom Left Guide Pad –
QTY (2)
1” Bottom Right Guide Pad –
QTY (2)
#50 Roller Chain – QTY (as
needed)
Roller Guide Wheels - QTY
(2) per Head
Bearing for 28 in Wheel (4
Bolt Hole) - QTY (1) per Head
Hydraulic Pump (If equipped
w/ hyd. Feedworks) QTY - (1)
141014 1 ¼” Bottom Left Guide Pad –
QTY (2)
141015
121007
111013 5VX710 Drive Belt -- QTY (2)
171077 Spindle Nut N-11 – QTY (1)
181019
1 ¼” Bottom Right Guide Pad –
QTY (2)
#50 Connector Link – QTY (10)
Hydraulic Filter (If equipped w/
hyd. Feedworks) QTY - (1)
Service Contact Information
In the event that you have any problems, call us at (573) 663-7711 any time between 8:00
AM and 5:00 PM (CST), Monday through Friday.
Serial Number Location
The model and serial number are located on the front side of the machine near the operator
station.
Please refer to your serial number and model number when speaking to a service
technician or ordering replacement parts.
Baker Band Resaw - Rev 1, 09/08; WWW.BAKER-ONLINE.COM
26
Wiring Diagrams
High Voltage
Baker Band Resaw - Rev 1, 09/08; WWW.BAKER-ONLINE.COM
27
Wiring Diagrams (continued)
Low Voltage
Baker Band Resaw - Rev 1, 09/08; WWW.BAKER-ONLINE.COM
28
Loading...