Bakbar H35 Service Manual

INSTALLATION / OPERATION /

SERVICING MANUAL

H35 EXTRACTION HOOD

F22457-5

MANUFACTURED BY

Moffat Limited
PO Box 10001
Christchurch
New Zealand
Ph: [phone]
Fax: [phone]

WORLD-WIDE BRANCHES

UNITED KINGDOM

Blue Seal
67 Gravelly Business Park
Gravelly Park
Birmingham
West Midlands
B24 8TQ
Ph: [phone]
Fax: [phone]

UNITED STATES

Moffat Inc
3765 Champion Blvd
Winston-Salem
North Carolina 27115
Ph: [phone]
Fax: [phone]

CANADA

Serve Canada
22 Ashwarren Road
Downview
Ontario M3J1Z5

Toll Free:800 263 1455
Ph: [phone]
Fax: [phone]

[e-mail]
www.servecanada.com
www.moffat.com

NEW ZEALAND

Christchurch

Moffat Limited Moffat Limited
PO Box 10-001 4 Waipuna Road
16 Osborne Street Mt Wellington
Christchurch Auckland
Ph: [phone] Ph: [phone]
Fax: [phone] Fax: [phone]

AUSTRALIA

Victoria

Moffat Pty Limited Moffat Pty Limited
740 Springvale Road 3/142 James Ruse Drive, Rose Hill
Mulgrave, Melbourne PO Box 913, Smithfield
Victoria 3171 Sydney, N.S.W. 2142
Ph: [phone] Ph: [phone]
Fax: [phone] Fax: [phone]

Western Australia

Moffat Pty Limited Moffat Pty Limited
67 Howe Street 30 Prosperity Place
Osbourne Park Geebung, Brisbane
WA 6017 Queensland 4034
Ph: [phone] Ph: [phone]
Fax: [phone] Fax [phone]

Auckland

New South Wales

Queensland

The reproduction or copying of any part of this manual by any means whatsoever is strictly forbidden unless authorized previously in
writing by the manufacturer.

In line with policy to continually develop and improve its products, Moffat Ltd. reserves the right to change the specifications and
design without prior notice.

© Copyright Moffat Ltd. February 2008.

Contents

Introduction ........................................................................................................ 2

Installation..........................................................................................................3

Before Installation
Model Options
Installation onto E35 Convection Oven

Specifications.....................................................................................................6

Operation............................................................................................................8

Extraction Fans
Condensate Collection

Cleaning.............................................................................................................. 9

Trouble Shooting .............................................................................................10

Servicing........................................................................................................... 11

Spare Parts.......................................................................................................12

Wiring Chart .....................................................................................................13

Date Purchased................................................................. Serial No ..........................................................

Dealer............................................................................................................................................................

Service Agent ................................................................................................................................................

1

Introduction

We are confident that you will be delighted with your H35 EXTRACTION HOOD, and it will become a most
valued appliance in your commercial kitchen.

A new appliance can seem very complex and confusing at first glance. To ensure you receive the utmost
benefit from your new Extraction Hood, there are two important things you can do.

Firstly

Please read the instruction book carefully and follow the directions given. The time taken will be well
spent.

Secondly

If you are unsure of any aspect of the installation, instructions or performance of your Extraction Hood,
contact your H35 dealer promptly. In many cases a phone call could answer your question.

2

Installation Requirements

It is most important that this extraction hood is installed correctly and that operation is
correct before use.

Installation shall comply with local electrical, health and safety, and ventilation
requirements.

Installation

Before Installation

Unpack and check unit for damage and report
any damage to the carrier and dealer. Report
any deficiencies to your dealer. Check that the
unit has been supplied with installation
accessories as listed below:

1 Vent Condensate Drain
1 Hood Condensate Hose
2 Hose Clamps

Figure 1.1

1 Drain Outlet

Figure 1.1

1 Gasket
1 Connection Sleeve
4 Cable Ties—Push Mount
1 Snap Bush—Dia 19mm
1 Silicone RTV Tube 150g

Model Options

The H35 extraction hood is available in two
different model options to suit the two sizes of
E35 convection oven.

Ensure that the H35 model is correct for the E35
oven size it is to be fitted to.

H35-26 1080mm deep to suit E35-26

convection oven (880mm deep).

H35-30 1180mm deep to suit E35-30

convection oven (980mm deep).

Note:

In both cases the extraction fan hood has

a 200mm overhang at front of oven.

An incorrect H35 model size will not fit an E35
convection oven. Refer to specification section
for more dimensional detail of H35 models and
E35 convection ovens.

Installation Onto E35 Convection
Oven

1) Remove left hand and right hand side panels,
and rear right hand service panel from E35
oven.

2) Remove E35 oven top panel by removing
screws on underside of top panel at four cor­ners.

Screws

(4)

Figure 1.2

3) Insert 19mm plastic bush into 19mm hole in
chassis top rail of E35 oven.

19mm Bush

Figure 1.3

4) With accessories bag removed from vent out­let chamber of H35 extraction hood, place
H35 on top of E35 oven (with extraction grill
at front).

Note:

Ensure oven vent tube is located into

hole in H35 base.

Rear of hood should be flush with rear of

oven when fitted correctly.

3

Installation

5) Secure hood to oven with one 3/16” BSW
screw in each corner as shown in figure 1.4.

Screw

Figure 1.4

6) Remove right hand side panel from hood (4
screws).

7) Make connection from E35 oven vent tube to
H35 connection elbow with connection sleeve
and two hose clamps supplied.

Note:

A tube of RTV silicone has been
supplied with the hood for use with this
connection.

Fully silicone the connection 20mm above

and below the joint before fitting the sleeve
and clamps to ensure a leak proof
connection.

9) Remove plug from hole in rear upright of oven
chassis.

Plug

Figure 1.7

10) Insert outlet pipe through hole in chassis rear
(see above). Secure with two screws.

11) Attach drain spigot to bottom flange of vent
using supplied gasket and RTV silicone
sealant.

Drain Spigot

Hose
Clamps

Figure 1.5

8) Remove end plate from bottom of E35 oven
vent tee.

End
Plate

Figure 1.6

Figure 1.8

12) Feed hood power supply cable through
bushing at top of E35 oven. Route supply
cable down to mains terminal blocks,
securing to oven upright with push-fit cable
ties, and attach to L1, Neutral , and Earth.

Hood Power

Supply Cable

Figure 1.9

4