Baiyun Cleaning A201, Q201, K201, Y201, T201 Product Manual

Environmental tips

Guangdong Baiyun Cleaning Group Co.,Ltd.

Please dispose of the package, used components (battery) and hazardous fluid (antifreeze and machine oil) properly according to local waste disposal regulations to ensure environmental safety.

ISO9001:2008 International Quality System Certified

PUSH-BEHIND FLOOR SCRUBBER

Please remember to recycle them for further use if possible.

201 SERIES

Product Manual

Applicable model A201 Q：、 201 K201 Y201 T201.、、、

This manual contains important safety precautions and instructions on the correct operation of product. Please read this carefully before using the product.

Version:A/0-2014

Guangdong Baiyun Cleaning Group Co.,Ltd.

201 Series Push-behind

Guangdong Baiyun Cleaning Group Co.,Ltd.

Floor Scrubber Optional Spares

Description:1.201 series:A201 Q201 K201 Y201 T201.、、、、

Brush:14" brush with 0.7mm bristles

2.The following pictures are only for reference, so products are subjects to what you get.

Front squeegee

Rear squeegee

Front squeegee: standard squeegee with 6 holes

Front squeegee: oil-resistant squeegee

Front squeegee: customized hole position

Rear squeegee: standard squeegee

Rear squeegee: oil-resistant squeegee

Pad driver:14" floor scrubber

pad driver

Pad driver

buckle

Description of symbols in this manual

Description of symbols on the machine

Remark:

CONTENTS

Guangdong Baiyun Cleaning Group Co.,Ltd.

WARRANTY INFORMATION

Disclaimer

3 5

7 7 8

9 9

10 13

14 15

AFTER-SALES SERVICE

Guangdong Baiyun Cleaning Group Co.,Ltd.

PACKING LIST

After-sales service

Limited warranty statement

Standard configuration

No. Name Unit

Main Unit

Squeegee assembly

Power cable

Product manual

Conformity certificate

Piece

Set

Piece

Copy

Piece

Quantity

Unpacking check

Check the product on receiving immediately. If there will be obvious damages on the

product, please keep the packing materials and contact the local distributor.

OPERATION INSTRUCTIONS

Guangdong Baiyun Cleaning Group Co.,Ltd.

TECHNICAL DETAILS

Key components

Wiring diagram

Green

Brown

White

Black

Brown

White

Black

Blue

Brown

Red

Yellow

green

Red

Running capacitor

Starting capacitor

Red

Green

X2capacitor

Blue

Brown

Yellow

green

Brush mot or

Yellow green

Brown(Black)

Blue

(Red)

432

Yellow

Blue

17 18

Power cable

Vacuum

motor

White(Blue)

Black

Blue

Black

Brush motor switch

Control panel

Serial number

Handle adjustment switch

Handle lever assembly

Squeegee adjustment lever

Vacuum hose

Recovery tank lid

Recovery tank

Solution tank frame

Wheel

Squeegee assembly

Suction hose

Solution tank

Solution tank lid

Circuit board assembly

Brush motor

Vacuum motor

Solenoid valve

Protect cover

Brush assembly

Black White

TECHNICAL DETAILS

Guangdong Baiyun Cleaning Group Co.,Ltd.

OPERATION INSTRUCTIONS

Technical specifications

Description

Protection level

Operating tension

Vacuum motor

Suction vacuum

Brush motor

Brush speed

Noise level

Solution tank capacity

Recovery tank capacity

Squeegee width

Theoretical cleaning efficiency

Brush diameter

Cleaning width

Unit

IPX

mmH O

rpm

m /h

inch

Data

200

1300

300

140

≤

11. 8

13.4

1500

Description of control components

① Control panel

(See on the instruction of the control panel.)

② Brush motor switch

Hold on the switch to make the brush motor work. Release it, the brush stops working.

③ Handle adjustment switch

Operate the switch to regulate the angle of the handle lever.

Description of control panel

② ③①

①

② ③

Brush pressure

Maximum gradient

Minimum turning radius

Power cable length

Machine dimensions(Without squeegee)

Package weight(Without battery)

kg.f

deg

025

42x41x86

34.7

Vacuum switch

①

Press this switch, the vacuum motor begins to work. Press it again to turn off the vacuum motor.

②

ON/OFF switch

Press this switch to turn on or off the power.

③

Sprinkling

Press this switch the sprinkling motor starts to working. Then, press this again, the sprinkling motor comes to a complete stop.

switch

Assembling parts

1.Squeegee assembling

Put the end hole on the revolving shaft of the squeegee assembly as axile and assemble the revolving shaft assembly, spring, shaft. Then, insert and unfasten the opening bolt with the holes of the revolving shaft. After that, use the locking nut to connect the revolving shaft assembly with the shaft on the solution tank frame. At last, connect the suction hose

OPERATION INSTRUCTIONS

Guangdong Baiyun Cleaning Group Co.,Ltd.

MAINTENANCE GUIDE

Assembling parts

into the suction mouth on the squeegee frame to complete the assembling of the squeegee assembly.(fig.2)

Revolving shaft assembly

Spring

Shaft

Squeegee assembly

fig.1

Locking nut

Opening bolt

Revolving shaft

Suction inlet

Squeegee assembly

fig.2

● Squeegee ascending and descending●

After the cleaning work, lift up the squeegee assembly and remove the brush in case that the squeegee and the brush deform. Pull the squeegee lever upward to ascend the squeegee assembly, and pull it downward to descend the squeegee assembly. The specific steps to

remove the brush is seen on the page 6 as the instructions of brush assembling(fig.2)

2 Brush assembling.

Attention

Do not operate any function button while hands are touching the brush, in case of injuries.

●

Make sure the scrub pad is placed with the center of the pad driver and screw the pad

●

driver buckle.Afterwards, you can work as follows.

1.Make the operation handle vertical and put the machine downward on the floor. Then, align the brush with the three-blade plate and rotate the brush 30 to the left.After that, the brush assembling will be finished and place the machine well.(fig.3)

2.If the brush is needed to change, hold on and rotate it 30 to the right to remove the brush.(fig.4)

Trouble shooting

1 The machine socket has not been

connected well with the battery socket.

2.The related motor switch has not been switched on.

3.The voltage of the machine is not normal or stable.

4.The related indicated lights blinks abnormal.

1.The seal ring of the soiled water recovery tank lid gets loose.

2.The hose hoop gets loose.

3.The water suction motor gets loose or tilts.

4.The water suction hose is obstructed.

5.The vacuum hose is broken.

1.Attach the seal strip properly without space.

2.Check the hose hoop and install it properly.

3.Open the silencer lid to make sure

the motor is installed correctly and properly.

4.Clear out the air inlet and outlet.

5.Repair the vacuum hose.

Rotate it 30 to the left

Three-blade plate

fig.3

Rotate it 30 to the right

fig.4

MAINTENANCE GUIDE

Guangdong Baiyun Cleaning Group Co.,Ltd.

OPERATION INSTRUCTIONS

Daily maintenance

4.Maintain the brush

Hold on the brush and rotate it 30 to the right to remove the brush(fig.13&fig.14), and then clean them. If the machine will lay idle for long time, the brush should be removed, cleaned and air-dried, otherwise, the load of the brush motors may be too strong when it is being used again and even worse, can’t operate normally.(fig.15)

Rotate it 30 to the right

fig.13 fig.14 fig.15

Brush

Rinse

●Brush assembly exploded diagram●Brush assembly exploded diagram

Brush motor

Brush motor plate

Brush holder

Pulley

Working before preparation

1.Fill the solution tank Open the solution tank lid, then fill the water

①

or dilute neutral detergent into the solution tank from the inlet mouth.

②

The temperature of water or detergent should be lower than 50℃.

Solution tank lid

Attention

To avoid shortening the service life of the machine, detergents added into the solution tank should be less foamy and less volatile neutral detergents with a PH of 5-9.

. 3.Check whether the

2 Check whether the

brush is assembled well. If not, assemble them according to the instruction of “Brush assembling” on Page 7.

Brush

4.Insert the plug into the power socket to connect the power, and then press the function buttons on the control panel to make sure the brushes, the squeegee assembly, the suction pump and the sprinkling pump are ready for work.

squeegee assembly is assembled well. If not, assemble the squeegee assembly according to the instruction of “squeegee assembling” on Page 4.

Protect cover

Brush

Turn off ON/OFF switch

Connect the power

OPERATION INSTRUCTIONS

Guangdong Baiyun Cleaning Group Co.,Ltd.

MAINTENANCE GUIDE

Operation steps

After the preparation work, operator can use the machine to begin the cleaning work.

1 Check whether the sprinkling

button and the vacuum button are turn off. Then switch on the ON/OFF switch on the control panel(fig.5-a), the machine will in manual state.

2.Press the sprinkling button on the control panel(fig.5-a), the solenoid valve begins to work, the machine starts sprinkling water.

3.Put down the squeegee lever to ensure that the squeegee is totally touched with the floor to work.

4.Hold on the brush motor switches on both sides (fig.5-c), the brush can clean the floor.

5.After cleaning the work, lift up the squeegee lever and release the brush motor switches. Then, press the sprinkling button, vacuum button, ON/OFF switch to stop all cleaning work.

c. Hold on the brush

motor switch

5

a. Press the function

buttons

ON/OFF switch

Vacuum switch

squeegee

b. Put the squeegee

lever down

Sprinkling switch

lever

Daily maintenance

Solution

tank lid

Quick

connector

Turn off the ON/OFF switch

fig.11

Water pipe

fig.12

Ball valve

3.Maintain the squeegee

Remove, clean and air-dry the squeegee regularly to prolong the service life. The whole

squeegee assembly can be removed, to be cleaned and air-dry.

The procedure to remove the squeegee:

①

Turn the two star nuts anticlockwise to remove the squeegee assembly.

②

Release the squeegee clasp to loosen the retaining metal strip assembly. Then pull the two triangle clasps downwards to take out the retaining metal strip assembly.

③

After taking out the retaining metal strip assembly, the rear squeegee can be

removed.

④

Loosen the upper and lower inner pads and then the front and rear squeegee can be removed. Check to confirm the wearing condition of the squeegee and turn to an untouched side for use. Each squeegee has 4 sides for switching use.

Star nuts

Note

During the cleaning work, change the water flow according to the condition of the floor. The ball valve above the brush cover can be used to adjust the water flow.After the cleaning work, pull the water pipe from quick connector can discharge water in the solution tank (fig.6).

Quick connector

Water pipe

Ball valve

fig.6

Triangle

clasp

Upper inner pad Lower inner pad

Squeegee

clasp

Squeegee holder

Suction hose

Retaining metal strip assembly

Front squeegee

Rear squeegee

MAINTENANCE GUIDE

Guangdong Baiyun Cleaning Group Co.,Ltd.

Daily maintenance

Attention

When the cleaning work is over:

1.Disconnect the machine socket from the battery socket.

2.Drain the soiled water from the recovery tank and wash it with clean water.

3.Check to make sure the water suction hose is clear.

4.Wash the brushes and squeegees, and air-dry them.

1.Maintain the recovery tank

●Clean the recovery tank every time the cleaning work is finished.

①

Take out the vacuum hose and the drain hose from the recovery tank lid. Then, pull out

the whole recover tank to separate it from the machine.

Loose the two recovery tank lids and turn over the recovery tank to discharge all the

②

soiled water. Use the clean water to wash the recovery tank and air-dry it. Take care of preventing

③

sludge or foreign objects from blocking the water. After cleaning the recovery tank, fasten the two recovery tank lids.After that, push the

④

recovery tank into the machine. Finally, connect the vacuum hose and the drain hose with the mouth of the recovery tank.

●Clean the strainer periodically.(fig.10)

Vacuum

hose

Solution tank lid

Solution

tank

Recovery tank lid

Drain hose

Recovery tank

Don’ts

Notes before using

Strainer

fig.9

2.Maintain the solution tank

If the machine stay idle for long time, open the solution tank lid and quick connector to

●

discharge deteriorates(fig.12).

If the machine will be transported or stored when the environment temperature is less than

●

4 fter this, twist down the ball valve.

℃, discharge all the solution water in the solution tank. A

Then press the sprinkling button to sprinkle all the water stayed in the sprinkling system (fig.11). Otherwise, water may freeze and damage the sprinkling motor, solenoid valve, and hoses because of lower water temperature.

all the solution water in the solution tank in case of solution in the tank

fig.10

SAFETY PRECAUTIONS

Guangdong Baiyun Cleaning Group Co.,Ltd.

IMPORTANT PRECAUTIONS

Warning

Safety precautions

Forbidden

Turn off the ON/OFF switch

fig.7

Working conditions

1.Working environment temperature

The machine can only work in the 10 - environment.℃35℃

2. Sensibility to strong acid and strong alkali

Do not put strong acid or strong alkali liquids into the water tank to deal with stubborn dirt, in case those liquids damage the components of the water channel. If those liquids are needed, sprinkle them on the floor directly

The detergents put into the water tank should be neutral detergents with a PH of 5-9.

3. Cleaning areas

If there are too much dirt and big rubbish on the floor, such as wastepaper, plastic bags, fruit peel, fruit seeds and so on, it is recommended to sweep the floor first, and then use the machine to clean the floor, in case big objects block the water suction hose.

Notes on moving

1.While driving, keep the machine from colliding with other objects. Before entering a narrow space, check whether the machine can get in.

2.Avoid driving the machine over rough places in case of mechanic damage, which will shorten the servicing life of the machine

3.The width of the aisle should be at least 47cm for the machine with the squeegee assembly

to get through. If the width of the aisle is less than 47cm,remove the squeegee assembly, and then let the machine get through. Do not force the machine to get through, which may result in mechanical problems.

fig.8

13.If the user use the non-original batteries or chargers, please contact the manufacturers in advance in order to avoid accidents.

47cm

Baiyun Cleaning A201, Q201, K201, Y201, T201 Product Manual

Specifications and Main Features

Frequently Asked Questions

User Manual