Page 1
Page 2
THANK YOU FOR PURCHASING A B-AIR PRODUCT.
Before Grooming
Be careful not to blow air into the animal's face, ears or nose. Use the cone nozzle to
blow out dirt from the undercoat and separate matted hair
After Bathing
Towel-dry the animal to remove excess water. Use the cone nozzle to blow off
moisture working out from the skin. Switch to one of the other attachments to dry
more sensitive areas.
Operation I Use
•
Plug the flexible hose to the front cap connector
•
Plug in the power cord and switch power on
•
Adjust the variable wind speed switch knob and select the desired setting
according to your needs
•
Turn the variable wind speed switch knob back to minimum and turn off the
power switch after usage
•
Unplug the dryer from the power source and unplug the hose and nozzle when
you are finished using the dryer
Power Requirements
Cords
Use a single outlet that is at least 20 amps and has a ground wire. Use the unit with
a correct outlet and do not share the same outlet with other app liances.
Use 3 pronged adapters that are UL and CE approved with Ground Fault Circuit
Interrupter
(G.F.C.I
).
Do not use power cords
that show any
sign of wear
or
damage
.
Cords are not covered by warranty.
Page 3
Safety
•
Do not immerse the unit in water. Exposure to water will result in electric shock
•
Do not alter or remove the grounding plug. Do not use the unit if it cannot be
properly grounded
•
Do not use the unit if the power cord is frayed or shows any sign of wear
•
Do not place the unit in standing or running water. Exposure to water will result in
electric shock
•
Do not let the air intakes of the unit get blocked or clogged. Overheating of the
equipment may occur and cause fire or an electrical hazard
•
Never use the unit without a filter in place
•
Do not leave the unit unattended when in use and I or turned on
•
Individuals with pacemakers should not use this machine
•
Always hold the nozzle and hose firmly when the unit is in operation
Maintenance
•
Clean filters regularly (every 2 months) by washing or air blowing. Be sure not to
use the unit without a filter in place
•
Keep the surface of the unit clean and dry
•
Refer to the guide in this owner's manual to replace motor brushes. Replace
brushes every 4-6 months
Limited Warranty
Proof of purchase is required on all warranty claims .
Warranty covers against defects in material and craftsmanship used under normal
intended use to original purchaser for a term of (2) two years from t
he original date
of purchase including parts, labor and 1 way shipping. Housing is covered for a term
of (5) five years from the date of the original purchase.
Important!
Warranty does not cover signs of misuse including, but not limited to rough handling,
abuse, tampering, improper voltage use and unauthorized maintenance and repairs.
Specifications:
VOLTS
115 V
CYCLE
60 Hz
FPM
55000
AMPS
14
CFM 445
WEIGH T NET/ SHI P
16/20
UNITSIZE(L x W x H)
19” x 6” x 10”
UNITSIZE BOX (L x W x H)
23” x 9” x 15”
HOSE L ENGT H
5FT
MOTOR
2.1HP
NOISE
LEVEL
76-84
SPEEDS
VAR IABLE
Page 4
Motor Brush Replacement steps.
Page 5
Item No.
Part Name
Quantity
TD-90056
B-air Rear Cap Knob
1
TD-90005
Rear Cap
1
TD-90007
Foam Filter
1
TD-90057
B-air Double Motor Dryer Handle
1
TD-90009
M4x12 Screw and Nut
9
TD-90013
PA3x1Q Self-tapping Screw
4
TD-90058
B-air Long Housing-PMS213
1
B-air Long Housing-PMS265
B-air Long Housing-PMS311
8-air Long Housing-PMS375
TD-90059
8-air Long Housing Base
1 TD-90060
Long Rubber Foot(left)
2
TD-90061
Long Rubber Foot(right)
2 TD-90015
M5x6 Screw
16
TD-90016
Vibration Absorber Ring
1
TD-90017
Motor A 2
TD-90018
Rubber Washer
2
TD-90019
Carbon Brush
2
TD-90046
Dual Motor Fixture Bracket
1 TD-90045
Middle Rubber Ring
1
TD-90020
Single Motor Fixture Bracket
1 TD-90044
Connection Terminal
1 TD-90023
PA3x16 Self-tapping Screw
7
TD-90021
Rubber Seal
1
TD-90025
PG-9 Waterproof Cable Connector
1
TD-90026
Power Cable
1 TD-90028
Wind Speed Knob
1 TD-90030
Power Switch
1
TD-90042
PCB-B(220V)
1
PCB-B(110V)
TD-90043
Front Cap -8
1
TD-90031
Front Cap D52 Hose Connector
1
TD-90032
052 Nylon Clip
1 TD-90062
12' Hard Pipe
1
TD-90034
D52 Hose Connector
1
TD-90063
Rubber Flat Narrow Nozzle
1 TD-90064
Rubber Round Nozzle
1
TD-90065
M4x8 screw and nut
1
TD-90066
High tempera-
ture resistant
silicone wire
-A
Brown,0.75mm'x200mm
1
-B Blue, 0.75mm'x200mm
-C BIUM l, 0.75mrrfx360mm
-D
Blue, 0.75mrrfx360mm
Page 6
Page 7
WARRANTY REGISTRATION
THIS WARRANTY CARD AND YOUR BILL OF SALE MUST BE PRESENTED FOR WARRANTY SERVICE
B-Air
550 South Ayon Ave. Azusa, CA 91702
1-877-800-2247 (BAIR)
Fax: (626) 385-3307
Email: info@b-air.com
Web site: www.b-air.com
Please complete and mail or fax your product warranty registration card For multiple units please put
1st serial numbers on a separate
Page 8
550 South Ayon Ave
Azusa, CA 91702
Loading...