BaiCells CW0100 CPE Installation Guide
V1.0
All rights reserved © BaiCells Technologies Co., Ltd.
About This Document
This document introduces the installation and debugging steps of CW0100 outdoor
CPE equipment, which is used for guiding installer to install CPE correctly.
Copyright Notice
BaiCells copyrights this specification. No part of this specification may be reproduced in
any form or means, without the prior written consent of BaiCells.
Disclaimer
This specification is preliminary and is subject to change at any time without notice.
BaiCells assumes no responsibility for any errors contained herein. For more information,
please consult our technical engineers.
Revision Record
Contact Us
E-mail: support@baicells.com
Phone: 86-10-62607100
Website: http://www.baicells.com/
1
Contents
1. Installation Preparation ................................................................................................. 2
Out-of-Box Audit ...................................................................................................... 2 1.1
Installation Accessories .............................................................................................. 2 1.2
Installation Tools ...................................................................................................... 3 1.3
Installation Environment ............................................................................................ 4 1.4
Safety Protection ........................................................................................................ 4 1.5
2. Equipment Installation ................................................................................................... 5
Appearance ............................................................................................................... 5 2.1
Interface and Button .................................................................................................. 5 2.2
LED Indicators ............................................................................................................. 6 2.3
RF Specifications ......................................................................................................... 6 2.4
Install on Pole ............................................................................................................. 7 2.5
Install on Wall ............................................................................................................. 8 2.6
3. Wire Connection ............................................................................................................. 9
Make Ethernet Cable Connector ............................................................................. 9 3.1
Connect Ethernet Cable ......................................................................................... 13 3.2
Power On .................................................................................................................. 14 3.3
Lightning Protection of Cable ................................................................................... 15 3.4
4. Power on Detection ...................................................................................................... 16
Detection Item ........................................................................................................ 16 4.1
Ethernet Port Working Status .................................................................................. 16 4.2
CPE Configuration Check .......................................................................................... 16 4.3
CPE Access Test ........................................................................................................ 16 4.4
CPE Parameter Record ............................................................................................. 16 4.5
5. Regulatory Compliance ................................................................................................ 17
FAQ ............................................................................................................... 19 Appendix A
Contents of Figure
Figure 2-1 Appearance of CW0100 .............................................................................. 5
Figure 2-2 Install on pole A ........................................................................................... 7
Figure 2-3 Install on pole B .......................................................................................... 8
Figure 2-4 Mounting Hole of Install on Wall ................................................................. 8
Figure 3-1 Strip Shielded Twisted Pair ......................................................................... 9
Figure 3-2 Separate the metal net, wire of cable and aluminum foil layer .................. 9
Figure 3-3 Cut off the aluminum foil layer of twisted pair ........................................... 10
Figure 3-4 Color Order ............................................................................................... 10
Figure 3-5 Insert the twisted pair core into line card .................................................. 10
Figure 3-6 Insert line card into Connector .................................................................. 11
Figure 3-7 Crimping connector ................................................................................... 11
Figure 3-8 Impact the connector with cable shield layer ............................................ 11
Figure 3-9 Cut off the redundant part ......................................................................... 12
Figure 3-10 Completion of shielded connector .......................................................... 12
Figure 3-11 Connect Cable 1 ..................................................................................... 13
Figure 3-12 Connect Cable 2 ..................................................................................... 14
Figure 3-13 POE power Mode .................................................................................... 15
Contents of Table
Table 2-1 CW0100 Interface and button ...................................................................... 5
Table 2-2 LED Indicators .............................................................................................. 6
Table 2-3 RF Specification ........................................................................................... 6
Table 3-1 Lightning Protection Demand of Cable ...................................................... 15
1. Installation Preparation
Shielded RJ-45 connector and
line card
Out-of-Box Audit 1.1
Before opening the box, make sure the packaging cases are in good condition,
undamaged and not soaked. During the unpacking, avoid potential damaging impacts
from hits or excessive force.
Check whether the material in the box is consistent with “Shipping List” and is in good
condition and undamaged.
Note:
During the unpacking, if the outer package is damaged or soaked, stop unpacking and find the cause.
Report the issue to the vendor. For any shortage, miscarriage, or damage is identified, report the local
vendor within 10 days.
Installation Accessories 1.2
2
Shielded CAT5 twisted pair
The length of the cable is tailored
according situation of the
installation site.
Percussion drill
and some drill
Installation Tools 1.3
The following tools are needed during the installation.
3