Item
Description
Power cable
< AWG16, e.g., AWG14
RF antenna cable
50 ohm feeder
RF antenna*
Omni or directional
Optical fiber
Single mode optical fiber
Ethernet cable
Outdoor CAT6
Shorter than 330 feet (100 meters)
Ground cable
16mm² diameter yellow-green wire
LED
Color
Status
Description
PWR
Steady on
Power is on
OFF
No power supply
Steady on
The cell is activated
OFF
The cell is not activated
Fast flash: 0.125s on,
Slow flash: 1s on, 1s off
The board is normal
OFF
No power input, or board fault
Hardware alarm, e.g., VSWR
OFF
No alarm
Interface
Description
PWR
Power supply: -48VDC (-60V to -42V)
GPS
Port for optional external Global Positioning System (GPS)
antenna, N-female connector
ANT0
Port for external RF antenna 0, N-female connector
ANT1
Port for external RF antenna 1, N-female connector
ANT2
Port for external RF antenna 2, N-female connector
ANT3
Port for external RF antenna 3, N-female connector
OPT
Optical backhaul interface for connecting to external
transmission network and used for data backhaul
ETH
RJ-45 interface, used for debugging or data backhaul
China
North America
Address: 3F, Bldg. A, No. 1 Kai
China
Phone: +86-10-62607100
Phone: +1-888-502-5585
Email: sales_na@Baicells.com or
support_na@Baicells.com
Website: www.Baicells.com
Website: https://na.Baicells.com
Nova-436 Outdoor 4x1W TDD eNB
Quick Start Guide
May 2018
Version 1.2
Introduction
This quick start guide is intended for experienced installers. It provides
high-level milestones for installing the Baicells Nova-436 Outdoor 4x1W
TDD eNodeB. For more details, please refer to the Baicells Nova-436
Outdoor 4x1W TDD eNB Installation Guide on the website. If you will be
setting up the Nova-436 for dual carrier (split mode) operation, please
also refer to the Baicells Dual Carrier Configuration Quick Guide.
Check and Prepare
• 1 Nova-436 eNodeB unit
• 1 90V to 305V AC to 48V DC power adaptor
• 1 two-wire green power terminal
• 1 American standard power plug
• 2 SFP optical modules
• 1 GPS antenna assembly kit (including fixing accessories, M4*14
screw *2, 1 GPS jumper cable)
• 1 assembled installation bracket kit (assembled: 1 bracket, omega*4,
M10*160 outer hex bolt *4, M10 flat gasket*4, M10 spring gasket*4,
M10 nut*4; individual: M10 flat gasket*6, M10 spring gasket*6, M10
nut*6, M8*80 expansion bolt *2)
• 6 cold shrink tubes
• 2 ground terminals
LEDs & Interfaces
Green
ACT Green
0.125s off
RUN Green
Steady on
ALM Red
The board is loading
alarm
Install
Directional
Power On & Check LEDs
Check eNB Status in Soft ware
Base Station GUI login - http://192.168.150.1 (admin/admin), BTS Info >
Status Info > Cell Status = Active
OMC login - https://cloudcore.cloudapp.net/cloudcore/ (your email
address/your password), eNB > Monitor > Active Status
*When the eNB is operating in dual carrier mode, Cell 1 uses ANT2 and
ANT3 and Cell 2 uses ANT0 and ANT1.
Install GPS Antenna
Install eNB on Pole or Wal l
Pole diameter: 1.6 to 3.9 inches (40 to 100 mm)
NOTE: Please refer to the Baicells Dual Carrier Configuration Quick Guide
for configuration differences when planning to operate the Nova-436 eNB
in dual carrier (split sector) mode.
Overview
Connect GPS, RF, Optical Fiber, & Ethernet Cables
Open eNB wiring cavity; use cold shrink tubes
Connect Power & Grounding
©2017 Baicells Technology, Inc. All rights reserved. Baicells, Baicells
Technology, and the Baicells logo are trademarks or registered
trademarks of Baicells Technology, Inc. in the United States and in other
countries.
Tuo Rd, Haidian Dist, Beijing,
E-mail: contact@Baicells.com
Address: 555 Republic Dr., #200,
Plano, TX 75074, USA
Loading...