!"#$%&&'()*+,(-.(/01++2(345678(51!#(9'%2(:"0;"&
(
V
1.0
About This Document
This document is a user guide for Baicells’ Atom R9 Indoor 3.5GHz 5dBi CPE.
Copyright Notice
Baicells copyrights this specification. No part of this specification may be reproduced in
any form or means, without the prior written consent of Baicells.
Disclaimer
This specification is preliminary and is subject to change at any time without notice.
Baicells assumes no responsibility for any errors contained herein. For more information,
please consult our technical engineers.
Contact Us
BaiCells Technologies Co., Ltd. North America
Address: 555 Republic Drive, Suite 200 Plano, TX 75074
E-mail: support_na@baicells.com
Phone: +1-972-800-1157
Website: http://www.baicells.com/
All rights reserved ©
Bai C ells Technologies Co., Ltd.
(
(
1
<+0*%0*'(
1.((Hardware Specification(444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444(=(
>4>(()??%"2"0$%(44444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444(=(
>4=((@?%$#A#$"*#+0'(44444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444(B(
>4=4>((!"'#$(C%'$2#?*#+0(44444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444(B(
>4=4=((-D(@?%$#A#$"*#+0'(444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444(B(
>4=43((E0F#2+0,%0*(@?%$#A#$"*#+0'(4444444444444444444444444444444444444444444444444444444444444444444444444444444444444(G(
2.((Operation Steps(444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444(H(
3.((Configuration Guide(444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444(.(
34>((I+J(/0(444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444(.(
34=((K%*L+2M(@%**#0J'(4444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444(>N(
343((O#D#(@%**#0J'(4444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444(>3(
34P((@%$;2#*Q(@%**#0J'(44444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444(>P(
345((RSK(@%**#0J'(44444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444(>5(
34B((R+/S(@%**#0J'(4444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444(>5(
34G((@Q'*%,(@%**#0J'(444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444(>G(
4.((Trouble Shooting(44444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444(>G(
P4>((C%F#$%($"00+*()$$%''(*+(<SE(*T2+;JT(O#D#(444444444444444444444444444444444444444444444444444444444444444444(>G(
P4=((<SE($"00+*($+00%$*(*+(#0*%20%*(44444444444444444444444444444444444444444444444444444444444444444444444444444444444(>H(
5.((Regulatory Compliance(4444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444(>.(
Appendix A((Shipping List(44444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444(=N(
((
<+0*%0*'(+A(D#J;2%(
Figure 1-1 Front View of CN6671 .................................................................................. 2
Figure 1-2 Back View of CN6671 ................................................................................
3
Figure 1-3 Side View of CN6671 ................................................................................
4(
Figure 3-1 CPE Web Client Login Page .....................................................................
8(
Figure 3-2 Home Page of Web Client .........................................................................
9(
Figure 3-3 LET Settings.............................................................................................
10(
Figure 3-4 LET Status ...............................................................................................
10(
Figure 3-5 APN Management ...................................................................................
11(
Figure 3-6 LAN Settings ............................................................................................
12(
Figure 3-7 WLAN Settings ........................................................................................
13(
Figure 3-8 Security Settings ......................................................................................
14(
Figure 3-9 VPN Settings ...........................................................................................
15(
Figure 3-10 VoIP Settings .........................................................................................
15(
Figure 3-11 System Settings .....................................................................................
16(
((
<+0*%0*'(+A(U"V&%(
Table 1-1 LED Indicators of Front View ........................................................................ 2
Table 1-2 LED Indicators of Back View ........................................................................ 4
Table 1-3 Interfaces and Buttons of Back View ........................................................... 4(
Table 1-4 Interfaces and Buttons of Side View ............................................................ 4(
(
2
1. Hardware Specification
>4> )??%"2"0$%((
The front view of the CPE is shown in Figure 1-1.
Figure 1-1 Front View of CN6671
Index
Description
Dimension
167(H)*187(W)*44(T)mm
Weight
310g
Color
White
The LED indicators of the front view are described in Table 1-1.
U"V&%(>W>(IEC(/01#$"*+2'(+A(D2+0*(R#%L(
LTE Name
Description
Color
LED Behavior
Status Indicator
PWR
Power
Indicator
blue
OFF
No Power Supply
Steady On
Power On
WLAN
WLAN
Indicator
blue
OFF
WLAN function is disabled
Blinking
Data transmission through
WLAN
Steady On
WLAN function enabled
WPS
WiFi
Protected
blue
OFF
WPS disabled
Blinking
WiFi terminal being accessed
3
Setup
Steady On
WPS Enabled
Tel1 ~ Tel2
Voice
telephone
interface
indicator
blue
OFF
No connection with the voice
server
Blinking(1/sec)
Registering with the voice server
Blinking(2/sec)
Connection has been
established with the voice server
Steady On
Connected to the voice server
MODE
Mode
Indication
blue
OFF
No LTE network access
Blinking
LTE scan, connecting
Steady On
Connected to LTE network
LTE Signal
4 LTEs,
Indicate
connection
state and
signal strength
blue
All OFF
No Connection
One by one
signal bar
display, four
bars
Displays the current wireless
network signal strength; the
more bars the stronger the signal
In addition, two special status indicators (Firmware upgrading and reset process)
are described in the following:
Status
Indicator Status Description
Firmware upgrade
WPS + WLAN lights flash simultaneously
Reset process
All indicator lights are on except 4th strength signal indicator
The back view of CN6671 is shown in Figure 1-2.
4
D#J;2%(>W=(!"$M(R#%L(+A(<KBBG>(
The LED indicators of the back view are described in Table 1-2.
U"V&%(>W=(IEC(/01#$"*+2'(+A(!"$M(R#%L(
LTE Name
Description
Color
LED Behavior
Status Indicator
LAN1 ~
LAN4
Eth Indication
Green
OFF
Ethernet connection is not
established
Steady On
Ethernet connection is normal
Blinking
Ethernet interface data being
transmitted
The interfaces and buttons of the back view are described in Table 1-3.
U"V&%(>W3(/0*%2A"$%'("01(!;**+0'(+A(!"$M(R#%L(
Name
Description
ETH RJ45
4 LAN Ports
POTS-RJ11
2 RJ11 interface, phone / fax / POS, providing VoIP
functions under conditions of software support
Power
Power port is the linked power adapter which is parceled.
Power Switch
Power Switch
The side view of CN6671 is shown in Figure 1-3.
D#J;2%(>W3(@#1%(R#%L(+A(<KBBG>(
5
The interfaces and buttons of side view are described in Table 1-4.
U"V&%(>WP(/0*%2A"$%'("01(!;**+0'(+A(@#1%(R#%L(
Name
Description
Restore Button
Hold down for 10s to restore the factory settings
WPS
WiFi Protected Setup
WiFi
Turn on or off WiFi Function
USIM Slot
Support 1.8V/3.0V USIM
6
>4= @?%$#A#$"*#+0'((
>4=4> !"'#$(C%'$2#?*#+0((
Specification
Description
Comment
LTE Standard
3GPP Release 9
None
Ethernet LAN
Port
4 RJ-45 port 10/100 auto-sensing, autoMDX
LAN * 4
USIM
Support 1.8V/3.3V 2FF USIM
None
Tel Port
2 FXS RJ11 Ports
None
LED Indicators
POWER / WLAN / WPS / TEL / MODE /
Signal Strength / LAN Indicator * 4
None
Power Switch
Switch
None
Reset/Restore
Button
Tact Button
Long press over 10s
to restore the factory
settings
WPS
WiFi Protected Setup
None
Power Supply
Input: Universal range 100V~240V AC,
50Hz
Output: 12V DC 1A
None
(
>4=4= -D(@?%$#A#$"*#+0'((
No.
Feature
Capabili
Comments
Value
Unit
1
LTE Mode
TDD LTE
2
Channel Bandwidth
5/10/15/20
MHz
3
Max Output Power
17
dBm
25
4
Transmit Power
Dynamic Range
63
dB
5
LTE Standard
3GPP R9
6
Frequency
3650 ~ 3700
MHz
B43
7
Antenna Gain
5
dBi
8
WiFi Frequency
2400 ~ 2483.5
MHz
9
WiFi Channel BW
20/40
MHz
10
WiFi Antenna Type
2*2
MIMO
Built-in antenna
11
WiFi Antenna Gain
2
dBi
7
>4=43 E0F#2+0,%0*(@?%$#A#$"*#+0'((
No.
Feature
Capability
Value
Unit
1
Operating Temperature
-10 ~ 45
2
Storage Temperature
-20 ~ 60
3
Operating Humidity
0 ~ 95
%
8
2. Operation Steps
Make sure the CPE is turned off before you insert or remove the SIM card. Otherwise, the
CPE and SIM card may be damaged.
1. Insert the SIM card into the USIM slot.
Note:
If you want to remove the SIM card, please press down on the SIM card. The SIM card will pop up.
2. Insert the power adaptor and turn on it. The power indicator should light up to indicate
an operating power supply. Otherwise, you need to check the functionality of the
power adaptor.
3. Wait for 1 minute, if the MODE and SIGNAL STRENGTH indicators flash
simultaneously, it indicates that the SIM card did not connect to the device or is
invalid. You need to buy a new SIM card or contact the vendor.
4. The MODE indicator flashing indicates that the device is searching and registering to
the LTE network. If the device connects to the LTE network normally, the MODE
indicator will remain on. The SIGNAL STRENGTH indicator indicates the strength of
the LTE signal. If the device cannot connect to an LTE network, the MODE indicator
will begin blinking.
5. The WLAN indicator indicates whether the Wi-Fi function is enabled.
If Wi-Fi is enabled, mobile phones and laptops can connect to the network via Wi-Fi.
SSID is “Airtouch-8783”. No password is required the first time the device is used.
6. PCs and laptops can connect to the internet through the LAN port.
Attention
:
9
3. Configuration Guide
34> I+J(/0((
1. In the browser’s address column, type in http://192.168.1.1, and click “Enter” to open
the web client login page, as shown in Figure 3-1
D#J;2%(3W>(<SE(O%V(<&#%0*(I+J#0(S"J%(
2. Input user name “admin”, password “admin”, and click “Login”. The homepage of
the web client is given in Figure 3-2. The home page displays basic information of
the CPE.
(
(
(
(
(
(
(
(
(
10
D#J;2%(3W=(7+,%(S"J%(+A(O%V(<&#%0*(
34= K%*L+2M(@%**#0J'((
1. In the left navigation bar, choose “Network>LTE Settings”, as shown in Figure 3-3 and
Figure 3-4.
In “Network”, you can complete the LTE and LAN settings.
D#J;2%(3W3(IEU(@%**#0J'
D#J;2%(3WP(IEU(@*"*;'(
11
Don’t change the settings under “LTE Settings” unless directed otherwise.
! If the IMSI field is empty in the “Module Information” area, check whether the
SIM card has been inserted or damaged.
! The “Settings” area displays the connection type and connection status, the value
of “Status” will be unconnected, connecting, or connected. Select “Auto” mode
when choosing the “Connect Method”.
“Status” displays the current connection status:
! UL Frequency /DL Frequency: Frequency point that the cell will search in an
attempt to connect to the network. If the field is empty, it indicates that searching
for an LTE network is failed.
! RSRP0/RSRP1: Indicates the RSRP of the current channel. If the value is greater
than -110dBm, it indicates that the LTE signal is within the service scope of the
base station, if the value is greater than -95dBm, it indicates a strong LTE signal.
! SINR: Indicate the SINR of the current channel, if the value is greater than 25dB,
it indicates a high channel quality.
! Cell ID: Indicates the cell ID of the connection.
2. In the left navigation bar, choose “Network>APN Management”, as shown in Figure 3-5.
In general, leave the “APN Management” at the default values.
(
(
(
(
(
(
12
D#J;2%(3W5()SK(:"0"J%,%0*(
3. In the left navigation bar, choose “Network>LAN Settings”, as shown in Figure 3-6.
D#J;2%(3WB(I)K(@%**#0J'
13
! In LAN Host Settings area, note that IP address of LAN port and Subnet Mask
avoids conflict with the local gateway.
! In DHCP Settings area, distribute dynamic IP addresses for local WiFi and LAN
hosts. The IP address segment is the same segment with LAN Host Settings.
343 O#D#(@%**#0J'((
In the left navigation bar, choose “WiFi”. WiFi settings include the WLAN general
settings, WPS settings, SSID profiles, WLAN encryption types, password settings,
access management and WDS settings, as shown in Figure 3-7
D#J;2%(( (( (
14
3WG(OI)K(@%**#0J'(
34P @%$;2#*Q(@%**#0J'((
In the left navigation bar, choose “Security”. Security settings include general router
security functions, such as MAC/IP/URL filter, port forwarding, access restrictions, and so
on, as shown in Figure 3-8.
3WH(@%$;2#*Q(@%**#0J'
D#J;2%(( (
15
345 RSK(@%**#0J'((
In the left navigation bar, choose “VPN”. The VPN settings supports PPTP, as shown in
Figure 3-9.
3W.(RSK(@%**#0J'(
34B R+/S(@%**#0J'((
In the left navigation bar, choose “VoIP”. VoIP settings include SIP server settings and
user account settings, as shown in Figure 3-10.
D#J;2%(3W>N(R+/S(@%**#0J'(
D#J;2%(( (( (
16
17
34G @Q'*%,(@%**#0J'((
In the left navigation bar, choose “System”. System settings include maintenance, version
management, diagnostic service, and so on, as shown in Figure 3-11.
D#J;2%(3W>>(@Q'*%,(@%**#0J'(
4. Trouble Shooting
P4> C%F#$%($"00+*()$$%''(<SE(*T2+;JT(O#D#((
1. Check whether Wi-Fi is enabled.
Observe whether the WLAN indicator is on or flashing. If the WLAN indicator is OFF,
you need to change the “WiFi Settings” to enable WiFi function. Refer to 3.3WiFi
Settings.
2. The SSID or the password is incorrect.
In web client, enter the “WiFi Settings” and reset the SSID/password.
3. If web client cannot login, you need to reset the CPE.
Hold down the reset button for 10s to restore the factory settings.
18
P4= <SE($"00+*($+00%$*(*+(*T%(#0*%20%*((
! Without the SIM card or the SIM card is damaged (
1. Check whether SIM card has been inserted into the USIM slot.
2. Log into the web client, check whether there is a “PIN LOCKED” notification. If
this is true then you need to unlock SIM card as follows:
a) Go to PIN Management, type in: 1234.
b) If this doesn’t work type 12345678 into the PIN code input page.
c) Reset PIN code and Disable the PIN Verification.
d) If PIN code is incorrect, you need to contact the SIM card vendor.
3. Log into the web client, choose “LTE Settings”, and check the value of IMSI. If it
is empty and SIM card is normal, you need to reboot the CPE, wait for 1minute,
log in web client again, and check the value of IMSI. If it is still empty, change the
SIM card.
! Without LTE signal or LTE network access privilege
1. Check the status of the CPE indicator.
If the MODE indicator is continuously flashing, it indicates that the CPE is
searching for a network, wait for 5 minutes.
2. If the CPE still cannot connect to the internet, log into the web client, and enter
the “LTE Settings”. If the IMSI is invalid (did not align with the user agreement),
you need to change SIM cards or contact the SIM card vendor.
3. Log into the web client, and go to “Network>LTE Settings”. If the value of the
Connection Method is Manual, reset it to Auto, and reboot the CPE.
4. If the CPE still cannot connect to the internet, log into the web client, and go to
“Network>LTE Settings”. Check whether the value of the status is
Unconnected in the Settings, this indicates that the LTE network is abnormal,
and you need to contact the vendor. If the value of the status is Connecting for
a long time, it indicates that CPE is not within scope of the LTE network, and you
need to move CPE closer to a window.
5. If the CPE still cannot connect to the internet, it indicates that CPE is not in the
service network, and you need to contact vendor.
19
5. Regulatory Compliance
FCC Compliance
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
" Reorient or relocate the receiving antenna.
" Increase the separation between the equipment and receiver.
" Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
" Consult the dealer or an experienced radio/TV technician for help.
Warning
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20 cm between the radiator & your body.
IC Compliance
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) This device may not cause
interference, and (2) This device must accept any interference, including
interference that may cause undesired operation of the device.
20
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même
si le brouillage est susceptible d'en compromettre le fonctionnement.
The antenna(s) used for this transmitter must be installed to provide a separation
distance of at least 20 cm from all persons and must not be collocated or operating
in conjunction with any other antenna or transmitter, End-Users must be provided
with transmitter operation conditions for satisfying RF exposure compliance.
Appendix A Shipping List
Item
Quantity
Assembled product
1
12V/1A adapter
1
User Manual
1
21
Loading...