Batch Controller
Model CB-30
CTL-UM-01028-EN-03 (April 2017)
User Manual
Batch Controller Model CB-30
Page 2 April 2017CTL-UM-01028-EN-03
User Manual
CONTENTS
Scope of This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Safety Terminology and Symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
CB-30 Batch Controller Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Unpacking, Assembling and Installing the CB-30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Unpacking the CB-30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Assembling the CB-30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Wiring the CB-30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Flow Valve Solenoid Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Pulse Transmitter Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Remote Control Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
AC Power Supply Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Operating the CB-30 Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Setup Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Function Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Understanding the Batch Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Presetting Batch Values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
The Initial Batch Cycle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
The Wash Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Stopping the Batch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Manual Batching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Setting a Batch Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Determining the Compensation Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Determining the Scale Factor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Troubleshooting the CB-30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Page 3 April 2017 CTL-UM-01028-EN-03
Batch Controller Model CB-30
Page 4 April 2017CTL-UM-01028-EN-03
Scope of this manual
2.83” (72 mm)
SCOPE OF THIS MANUAL
The sections in this manual have been arranged in such a way that you can, step by step, install, program, operate and when
required, troubleshoot the instrument.
MPORTANTI
Read this manual carefully before attempting any installation or operation.
Keep the manual in an accessible location for future reference.
Safety Terminology and Symbols
Indicates a hazardous situation, which, if not avoided, is estimated to be capable of causing death or serious personal injury.
Indicates a hazardous situation, which, if not avoided, could result in severe personal injury or death.
Indicates a hazardous situation, which, if not avoided, is estimated to be capable of causing minor or moderate personal
injury or damage to property.
CB30 BATCH CONTROLLER DESCRIPTION
The CB-30 is a batch controller that accepts a signal input from the meter transmitter, scales it to the desired unit of measure
and—at a preset point(s)—sends a signal to operate the flow valve.
Other features include: automatic compensation for valve overrun, batch size limit, fail-safe shutdown, and manual batching.
UNPACKING, ASSEMBLING AND INSTALLING THE CB30
Unpacking the CB-30
OTE:N If damage to the shipping container is obvious, request that the carrier be present when the product is unpacked. All
claims for equipment damage during transit are the sole responsibility of the recipient.
After carefully unpacking the unit, check for any visible sign of damage. If found, notify the carrier for insurance purposes and
call the factory for possible replacement. Keep all packing material in the event that the unit must be returned to the factory.
OTE:N Operating temperature is 32…130° F (0…55° C) with a maximum humidity of 85% non condensing. Always select a
mounting location with proper ventilation and environmental protection.
2.64 in.
(67 mm)
5.63 in.
(138 mm)
Panel Cutout
5.67” (144 mm)
Figure 1: Panel Cutout and Mounting Dimensions
Page 5 April 2017 CTL-UM-01028-EN-03
Batch Controller Model CB-30
Assembling the CB-30
The CB-30 can be mounted on the flow meter, on a wall or shelf, or in an instrumentation panel. Figure 2 shows the exploded
view of a meter or wall mounted unit. In this configuration the CB-30 is shipped separately and must be installed as shown
(see wiring diagrams for proper transmitter signal connections).
The basic unit is equipped for panel mount. To install:
1. Measure and cut mounting hole to the dimensions shown in Figure 1 on page 5.
2. Install gasket around the mounting bezel.
3. Insert the unit through the front panel cutout.
4. Secure the unit to the panel with the mounting clips.
PARTS LIST
Figure 2: CB-30 Assembly
Description Part Number
Mounting harware kit 259170-005
Connector kit 259170-004
Replacement triac 259170-003
Replacement face plate 259170-002
Table 1: Parts list
Page 6 April 2017CTL-UM-01028-EN-03
Wiring the cb-30
WIRING THE CB30
The rear panel of the CB-30 controller contains connectors with screw terminals for connecting #28 to #14 gauge insulated
stranded wire (#18 gauge stranded wire is recommended).
A wire stripper and a small screwdriver are the only tools required. Figure 3 on page 8 through Figure 6 on page 11
illustrate step-by-step the proper wiring procedures for all standard and optional functions.
At installation, be sure to comply with the following requirements:
• Disconnect power to the unit before attempting any connection or service to the unit.
• Avoid using machine power service for AC power. When possible, a dedicated or lighting circuit is recommended.
• Do not bundle or route signal lines with power lines.
• Keep all lines as short as possible.
• Use shielded wire for all input wiring.
• Observe all local electrical codes.
TO PREVENT ACCIDENTS, POWER SHOULD BE CONNECTED ONLY AFTER ALL OTHER CONNECTIONS HAVE
BEEN COMPLETED.
Terminal Function
1 Common (GND)
2 Lockout
3 Common (GND)
4 24V DC in
5 Sends out 12V (50 mA)
6 Fast in
7 Slow in
8 Common (GND)
9 RESET
10 START
11 HOLD
12 MANUAL
13 Common (GND)
14 Output
15 —
16 —
BECAUSE THE CB-30 IS MICROPROCESSOR CONTROLLED, IT IS VERY IMPORTANT THAT THE POWER SUPPLY BE FREE OF
ELECTRICAL NOISE. AVOID USING POWER LINES THAT FEED HEAVY LOAD ELECTRICAL DEVICES SUCH AS PUMPS
AND MOTORS.
THE CB-30 POWER INPUT IS INTERNALLY FUSED AND PROTECTED FROM COMMON LINE NOISE BY A FILTERING NETWORK.
25 TRIAC
26 TRIAC
21 L1 85…265V AC
22 L2 85…265V AC
23 System Ground
Table 2: Wiring Terminal Identification
Page 7 April 2017 CTL-UM-01028-EN-03
Batch Controller Model CB-30
Flow Valve Solenoid Connections
The CB-30 uses an electronic optically isolated TRIAC to control the valve solenoid during the Batch process.
ALWAYS MAKE SURE TO CONNECT THE HOT AC LINE TO TERMINAL #21 AND THE NEUTRAL TO THE SOLENOID.
At the beginning of the Batch the normally open contacts will close, allowing the AC supply to energize the solenoid and open
the valve. At the end of the Batch the contact will open and interrupt the AC supply to the solenoid, therefore closing the
valve. The TRIAC is field replaceable.
TRIAC Rating SHARP S202T02F
Load Voltage 80…240V AC
Load Current 2 A
Transistor Output Terminal # 14 is activated at the same time as the TRIAC, for use with
external relays or transistor compatible input devices.
One open collector NPN. 12V DC max.
50 mA sink max. (1V DC type V CE at 50 mA)
Table 3: Flow Valve Solenoid Specifications
VALVE
SOLENOID
1
2345678910 11 12 13 14 15 16 25 26 21 22 23
OPEN COLLECTOR
TRANSISTOR OUTPUT
Page 8 April 2017CTL-UM-01028-EN-03
BADGER METER
BADGER METER
MODEL CB-30
MODEL CB-30
Figure 3: Flow Valve Solenoid Connections
COMMON
HOT
85 . . . 265V AC
POWER SUPPLY
Wiring the cb-30
USE SHIELDED CABLE
Pulse Transmitter Connections
The CB-30 is designed to accept pulses from open collector transistors or dry contact closure transmitters.
Before making any connections please make sure to comply with the following:
1. Always use shielded wire to protect the signal line from external noise (round shield to terminal #3).
2. Make sure the signal lines are not bundled with or touching power lines.
Figure 4 shows the connection to Model PFT-3E transmitter, usually supplied with a Badger Meter Industrial Turbo meter. The
Model PFT-3E provides an open collector transistor output for the CB-30.
Frequency DC to 5 kHz (high speed)
DC to 150 Hz (low speed)
Low Level 0…2V DC max.
High Level 8…20V DC max.
Impedance 4.7 KW pullup to +12V DC
VDC Current 2.5 mA steady state
Response 100 ms min pulse (high speed) 3.5 ms min pulse (low speed)
Table 4: Transmitter Count Input
MODEL PFT-3E
TRANSMITTER
RED
GREEN
BLACK
2345678910 11 12 13 14 15 16 25 26 21 22 23
1
BADGER METER
MODEL CB-30
NOTE: DO NOT GROUND
SHIELD AT METER
Figure 4: Pulse Transmitter Connections
Page 9 April 2017 CTL-UM-01028-EN-03
Batch Controller Model CB-30
SHEILD TO TERM 8
Remote Control Connections
For operator convenience and process automation the functions START, HOLD, RESET and MANUAL can be wired to be used
with remote mounted switches or with electronic control processors. Always use shielded wire to protect the signal from
external noise interference.
Control Inputs Remote start, reset, hold, manual, keyboard lockout
Frequency DC to 20 Hz typical
Type Current sinking
Logic Level sensitive
Low Level 0…2V DC max.
High Level 8…20V DC max.
Impedance 4.7 KW pullup to +12V DC
Current 2.5 mA steady state
Response 32 ms make and break time
Table 5: Remote Control Specifications
HOLD
MANUAL
START
RESET
1
234567891011 12 13 14 15 16 25 26 21 22 23
BADGER METER
MODEL CB-30
USE SHIELDED CABLE
Figure 5: Remote Control Connections
Page 10 April 2017CTL-UM-01028-EN-03
Wiring the cb-30
BUILDING GROUND
AC Power Supply Connections
CONNECT AC POWER ONLY AFTER ALL OTHER WIRING HAS BEEN COMPLETED.
The CB-30 has an internally mounted line filter and fuse for surge protection. The unit is designed to operate with
85…265V AC power only. Always make sure to connect terminal #23 to the electrical system ground.
AC Power Input 85…265V AC
Consumption 0 VA max.
Table 6: AC Power Supply Specifications
2345678910 11 12 13 14 15 16 25 26 21 22 23
1
BADGER METER
MODEL CB-30
85~265 VAC
HOT
NEUTRAL
Figure 6: AC Power Supply Connections
Page 11 April 2017 CTL-UM-01028-EN-03
Batch Controller Model CB-30
OPERATING THE CB30 FRONT PANEL
The CB-30 front panel consists of two displays. One is a continuous indicator of the preset batch and the other is used to show
the batch progress and all other preset and programming values. The display includes four annunciators that show batch
state. The 12-digit key pad includes all secondary preset functions and the four-key command pad is used to stop, start, and
reset the unit in addition to presetting the batch and allowing for manual operation.
Figure 7: Front Panel
Setup Sequence
The CB-30 is equipped with a programming lockout feature for critical data protection. To use this feature, install a jumper
wire between terminals 1 and 2. With the jumper in place, you cannot change the unit of measure, scale, limit, and
compensation values.
MPORTANTI
The unit of measure must be selected before the unit is used. Refer to Function Key 3 description under “Function Keys” on page 13
to select a unit of measure.
1
2 34567891011 12 13 14 15 16 25 26 21 22 23
BADGER METER
MODEL CB-30
Page 12 April 2017CTL-UM-01028-EN-03
Figure 8: Lockout Jumper
Operating the cb-30 front panel
Function Keys
In addition to serving as numeric keys to program the batch size or other values, these keys are used to set values for the
Wash Cycle, the Valve Compensation, the Scale Factor and the Batch Limit.
Remember: Always press ENTER after programming a new value or after viewing a present value.
Press and hold until the serial number appears..
Press ENTER to escape.
Press and hold until the software version appears.
Press ENTER to escape.
Press 3 to display the current unit of measure.
To change the unit of measure:
Press 0 for“no unit”; Press 1 for “gallons”; Press 2
for “liters”; or press RESET to restore the unit to
the last confirmed setting. Press ENTER to save
your selection.
The 3 key will be locked out when the keyboard is
locked out.
Press and release the WASH (6) key to program
the wash cycle amount of water (up to 999
gallons*). Program zero if no wash cycle is
needed..
Press and release the COMP (7) key to set the
valve overrun compensation amount (up to 999
gallons*). Refer to “UNDERSTANDING THE BATCH
CYCLE” on page 14 for information on how to
determine compensation.
Press and release the LIGHT (0) key to select the
display brightness. The numbers correspond to the
following percentages of brightness:
1 = 20% 2 = 40% 3 = 60%
4 = 70% 5 = 80% 0 = OFF
Press and release the ENTER key after a new value has
been selected. This enters the new value in memory.
Press and release the RESET key to reset all batch
counts back to zero (after a HOLD) to start a new
batch or to reprogram new preset values.
Press and release the START key to open the valve
and start the main batch, to start the wash cycle or to
resume operation after a HOLD condition.
Press and release the SCALE (8) key to set the
scale factor (from 0.0001 to 0.9999).
Press and release the LIMIT (9) key to set the batch
limit (up to 9999 gallons*). The CB-30 will not
allow any batch greater than the value entered.
Table 8: Dual-Purpose Function Keys
*Gallons or liters based on unit of measure selected.
Press and release the HOLD key to close the valve and
stop the batch or wash cycle at any point and reset to
zero or complete the batch manually.
Press and release the MANUAL key to batch manually.
The valve will be open as long as the key is depressed.
It will operate only after a HOLD or RESET condition.
Page 13 April 2017 CTL-UM-01028-EN-03
Batch Controller Model CB-30
UNDERSTANDING THE BATCH CYCLE
This section contains a detailed explanation of the typical procedure for batching water into the concrete mix using the
Badger Meter CB-30 controller.
The following parameters are used as an example for illustration purposes only:
• Total Batch to be dispensed into the mix = 250 gallons
• Amount of water for WASH Cycle = 30 gallons
• Overrun Compensation = 5 gallons
Presetting Batch Values
Initially the operator will preset all values as follows:
1. Press BATCH, then enter 250 and press ENTER.
2. Press WASH, then enter 30 and press ENTER.
3. Press COMP, then enter 5 and press ENTER.
The Initial Batch Cycle
When the operator presses START the unit will energize the valve solenoid and open the valve. The indicator will show
“BATCH“. The display to the left will start counting down from the preset value to the wash value, but begin closing the valve
at 35 gallons (wash plus overrun) and coast down to 30 gallons.
The Wash Cycle
The indicator will now show “WASH READY”. The operator presses START again, the indicator will show “WASH” and the
display will count down from 30 gallons to zero but begin closing the valve at 5 gallons (overrun) and coast down to zero. The
indicator will then show “BATCH READY“ again.
Stopping the Batch
The operator can stop the batch at any point during the run by pressing the HOLD key. If done during the batch cycle the
indicator will show “BATCH HOLD”. If done during the wash cycle it will show “WASH HOLD” After a HOLD command the
operator has three choices:
• Press RESET to start a new batch, or
• Finish the batch manually by pressing the MANUAL key, or
• Press START to continue and finish the preset cycle.
Manual Batching
If needed, the operator can stop the automatic batch cycle and finish dispensing manually. As long as the manual key is
pressed and held, the valve solenoid will be energized (valve open) and the counter will count UP from zero or from that
number when the HOLD command was received. Knowing the compensation value, it is up to the operator to release the
MANUAL key and stop the valve in time to prevent overruns.
Setting a Batch Limit
In order to prevent anyone from entering too large a batch, you can limit the maximum batch value that can be programmed:
1. Press LIMIT.
2. Enter the maximum allowable batch.
3. Press ENTER.
If a larger quantity than the limit value is entered, the batch display will blink until a lesser value is entered.
Page 14 April 2017CTL-UM-01028-EN-03
Understanding the batch cycle
MPORTANTI
The CB-30 is programmed at the factory with a pulse fail-safe period of three seconds. This means that if a transmitter pulse is not
received within three seconds of a START command or the last pulse, (in the middle of the batch) the valve will close and the display
to the left will start blinking. After correcting the problem (bad transmitter, valve or pump) press RESET to start over.
Determining the Compensation Value
When a slow closing valve is used, (to prevent water hammer) the CB-30 can be programmed to begin closing the valve ahead
of time to compensate for the water overrun during the closing period.
To determine the amount of overrun, run one or two batches with the CB-30 without a compensation value and without a
wash value.
1. Preset a typical batch (250 gallons).
2. Press START and let the batch run.
The counter will count down to zero, and if there is an overrun, the counter will display the amount as a negative number
(for example, –5. This is the number that must be programmed to compensate for valve overrun.
3. To program, press COMP, enter 5, then press ENTER.
The CB-30 will begin closing the valve 5 gallons prior to the Batch and Wash preset values that are programmed. On the
second test batch, the counter may actually stop short of zero (for example, at 1). This indicates that the compensation value
must be changed from 5 to 4 gallons.
Determining the Scale Factor
The scale factor is a number that multiplies the incoming pulses from the flow meter. It converts them to desired units of
measure such as US gallons, liters, imperial gallons or pounds.
To determine the appropriate factor for the type and model of flow meter in use, apply the following formula:
1 gallon (liters, etc.)
Pulse rate (liters, etc.)
= Scale Factor
Example: For a 3" Turbo, the pulse input coming from
the PFR-3E transmitter is 24.8 pulses per gallon.
Therefore:
1 gallon
24.8 pulses per gallon
= 0.0403
To set the scale factor:
1. Press SCALE.
2. Enter 0403.
3. Press ENTER.
The scale factor will appear as follows: 0 in the left display and 403 on the right display.
Turbo
Size
2" 34.72 0.0288
3" 24.80 0.0403
4" 5.12 0.1953
6" 2.16 0.4629
Pulses per
Gal
Scale Factors
PFT-3E
Table 9: Scale Factor
Page 15 April 2017 CTL-UM-01028-EN-03
TROUBLESHOOTING THE CB30
This section deals with most of the common problems that you may encounter with the CB-30, the possible causes and the
recommended remedies. Most problems are due to improper wiring and/or programming procedures. The problem may also
be in the flow meter, valve, pump, or other piece of equipment.
Be sure that all other equipment is functioning properly. The CB-30 is extensively tested at the factory before shipment.
However, the unit may get damaged during transit or installation. If after all possible remedies have been tried and the
problem persists, contact your local representative or Badger Meter.
Problem Possible Causes Remedies
Unit is powered but the display does not
light up.
Transmitter is connected but the CB-30 does
not count.
Valve does not close at set points. 1. Triac output is not properly connected.
Counter accumulates too many counts. 1. Wrong scale factor.
Some of the keys on the front panel are not
operational.
Unit stops counting at the beginning or in
the middle of a batch and closes the valve.
Incorrect AC power wiring. Re-check power wiring.
1. Incorrect transmitter wiring or
1. Check wiring diagrams.
broken wire.
2. Transmitter is defective.
3. Wrong scale factor.
2. Replace parts or entire unit.
3. Check scale factor calculation: For
example, if programmed 0.001 instead
of 0.100, unit will wait for 100 pulses
before decrementing one count.
4. Low frequency input must be on
4. Verify connection.
terminal #7.
5. Meter is defective, rotor not turning.
5. Disassemble meter, check rotor, replace
if defective.
1. Reconnect triac wiring.
2. Triac is defective.
3. Valve components are defective.
2. Contact factory for replacement.
3. Check and replace valve components.
1. Check scale factor calculation.
2. Electrical noise causing extra pulses.
2. Check wiring. Make sure power lines are
not touching or close to pulse signal
line. Always use shielded cable.
3. Excessive vibration
1. Broken switch behind front panel.
2. Problem with internal components.
Three second fail-safe has elapsed without
receiving a pulse.
3. Dampen vibration.
1. Replace CB-30 or return for repair.
2. Return unit to the factory.
Transmitter signal is not received by CB-30
due to: No flow through the meter, faulty
transmitter or faulty valve. Check all these
components; replace as needed and press
the RESET button to clear error.
Table 10: Troubleshooting
Control. Manage. Optimize.
Due to continuous research, product improvements and enhancements, Badger Meter reserves the right to change product or system specications without notice, except to the
extent an outstanding contractual obligation exists. © 2017 Badger Meter, Inc. All rights reserved.
www.badgermeter.com
The Americas | Badger Meter | 4545 West Brown Deer Rd | PO Box 245036 | Milwaukee, WI 53224-9536 | 800-876-3837 | 414-355-0400
México | Badger Meter de las Americas, S.A. de C.V. | Pedro Luis Ogazón N°32 | Esq. Angelina N°24 | Colonia Guadalupe Inn | CP 01050 | México, DF | México | +52-55-5662-0882
Europe, Eastern Europe Branch Oce (for Poland, Latvia, Lithuania, Estonia, Ukraine, Belarus) | Badger Meter Europe | ul. Korfantego 6 | 44-193 Knurów | Poland | +48-32-236-8787
Europe, Middle East and Africa | Badger Meter Europa GmbH | Nurtinger Str 76 | 72639 Neuen | Germany | +49-7025-9208-0
Europe, Middle East Branch Oce | Badger Meter Europe | PO Box 341442 | Dubai Silicon Oasis, Head Quarter Building, Wing C, Oce #C209 | Dubai / UAE | +971-4-371 2503
Slovakia | Badger Meter Slovakia s.r.o. | Racianska 109/B | 831 02 Bratislava, Slovakia | +421-2-44 63 83 01
Asia Pacic | Badger Meter | 80 Marine Parade Rd | 21-06 Parkway Parade | Singapore 449269 | +65-63464836
China | Badger Meter | 7-1202 | 99 Hangzhong Road | Minhang District | Shanghai | China 201101 | +86-21-5763 5412
Switzerland | Badger Meter Swiss AG | Mittelholzerstrasse 8 | 3006 Bern | Switzerland | +41-31-932 01 11 Legacy Document Number: IOM-199-01 941630
Loading...