Badger Meter B28SBM-AB, B28SLM-AB, B28SBR-AB, B28SLR-AB, B28SBS-AB Standard User Manual

...
Flow Monitor
B2800 Standard
DSY-PM-00276-EN-04 (March 2017)
User Manual
CONTENTS
Scope of This Manual � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 3
Unpacking and Inspection � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 3
Safety � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 3
Introduction� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 4
Operating the Monitor � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 5
Programming� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 6
Additional Scaling Parameters � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 9
Additional Input Options � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 11
Default K-factor Values � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 12
Battery Replacement � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 12
Installation Drawing� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 13
Battery Powered � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 13 Loop Powered � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 14
Troubleshooting Guide� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 15
Part Numbering Information � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 15
Specications � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 16
Replacement Parts� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 17
Mounting Options and Dimensions� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 18
Meter Mount � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 18 Remote Mount � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 18 Swivel Mount� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 19
Flow Monitor, B2800 Standard
Page ii March 2017DSY-PM-00276-EN-04
Scope of This Manual
SCOPE OF THIS MANUAL
This manual is intended to help you get the B2800 flow monitor up and running quickly�
MPORTANTI
Read this manual carefully before attempting any installation or operation. Keep the manual accessible for future reference.
UNPACKING AND INSPECTION
Upon opening the shipping container, visually inspect the product and applicable accessories for any physical damage such as scratches, loose or broken parts, or any other sign of damage that may have occurred during shipment�
OTE:N If damage is found, request an inspection by the carrier’s agent within 48
hours of delivery and file a claim with the carrierA claim for equipment damage in transit is the sole responsibility of the purchaser
SAFETY
Terminology and Symbols
Indicates a hazardous situation, which, if not avoided, could result in severe personal injury or death�
Considerations
The installation of the B2800 monitor must comply with all applicable federal, state, and local rules, regulations, and codes�
EXPLOSION HAZARD - SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY FOR CLASS I, DIVISION 2.
AVERTISSMENT
RISQUE D’EXPLOSION - LA SUBSTITUTION DE COMPOSANTS PEUT RENDRE CEMATÉRIEL INACCCEPTABLE POUR LES EMPLACEMENTS DE CLASSE I, DIVISION 2.
DO NOT CONNECT OR DISCONNECT EITHER POWER OR OUTPUTS UNLESS THE AREA IS KNOWN TO BE NON-HAZARDOUS.
AVERTISSMENT
RISQUE D’EXPLOSION. NE PAS DÉBRANCHER TANT QUE LE CIRCUIT EST SOUSTENSION, À MOINS QU’LL NE S’AGISSE D’UN EMPLACEMENT NON DANGEREUX.
MPORTANTI
Not following instructions properly may impair safety of equipment and/or personnel.
Page 3 March 2017 DSY-PM-00276-EN-04
Introduction
INTRODUCTION
The B2800 flow monitor is a state-of-the-art digital signal processing flow monitor, designed to provide exceptional flexibility at a very affordable price� Though designed for use with Blancett flow meters, this display can be used with almost any flow meter producing a low amplitude AC output or contact closure signals�
This flow monitor is capable of accepting a low level frequency input for calculating flow rate and total� The calculations can then be displayed in the desired units of measurement� The monitor’s large 8-digit by 0�75 in� (19�05 mm) numeric liquid crystal display makes extended range viewing practical� The second 8-digit by 0�38 in� (9�65 mm) alphanumeric display provides for selectable units viewing in run mode and prompts for variables in program mode� Finally, you can choose to display rate or total, or alternate between both rate and total�
Page 4 March 2017DSY-PM-00276-EN-04
Operating the Monitor
OPERATING THE MONITOR
Programming
Keys
Mode
Indicator
Units Display
And
Programming Choices
Rate / Total Display
And
Programming Choices
RUN PROGRAM
RELAY1 RELAY2
Figure 1: B2800 flow monitor
Buttons
MENU Switches to PROGRAM mode
UP
Scrolls forward through the parameter options and increments numeric variables
RIGHT
Scrolls backward through the parameter options and moves the active digit to the right
ENTER
Saves programming information, advances to the next programming parameter, and used in the reset process
Modes
RUN
Normal operating mode
PROGRAM
Used to program parameters in the display
Page 5 March 2017 DSY-PM-00276-EN-04
Programming
PROGRAMMING
Each turbine flow meter is shipped with either a K-factor value or frequency data� If frequency data is provided, the data must be converted to a K-factor before programming the monitor� K-factor information, when supplied, can usually be found on the neck of the flow meter or stamped on the flow meter body� The K-factor represents the number of pulses per unit of volume� The K-factor is needed to program the monitor readout�
Programming Mode
K Factor Units
Units
Pulse Output
IO/SETUP
METER
PUL/GAL PUL/FT3PUL/LTRPUL/M3
K FACTOR
GPM/GAL
LPM/LIT M3PH/M3
M3PD/M3
BPD/BBL
DSP
BOTH TO TAL R ATE TEST
PULS ON PULS OFF
PASSWORD
RST PSWD
Enter Program Mode
Press MENU to enter the programming mode� The mode indicator changes from RUN to PROGRAM
Select Meter Size
At the METER prompt, press UP or RIGHT to scroll to the bore size of your meter� Press ENTER to save and advance to the K-factor Units parameter�
OTE:N The meter connection size and the bore size are different� For example,
many of the one inch NPT turbines have bore sizes that range from 3/8…1 in� Be sure to use the correct bore size or the meter will report incorrect flows and totals�
Enter The K-Factor Unit
Press UP or RIGHT to scroll to the K-factor unit of the meter� Enter the unit that the meter was calibrated in�
Page 6 March 2017DSY-PM-00276-EN-04
Loading...
+ 14 hidden pages