Back to Basics Grain Mill Instruction Manual

 2008 Back To Basics®, a Brand of Focus Electrics, LLC.

www.focuselectrics.com

GRAIN MILL

Instruction Manual

Register this and other Focus Electrics products through our website:

www.focuselectrics.com

Assembling Your Grain Mill ...................................................................................... 2

Using Your Grain Mill ............................................................................................... 3

Cleaning Your Grain Mill ......................................................................................... 3

Helpful Hints............................................................................................................. 3

Warranty .................................................................................................................. 4

SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE

2

Assembling Your Grain Mill

Hopper

Clamp Screw with Lever

*The handle arm, wood handle grip, handle bolt and nut for the handle bolt is
considered the “Arm Assembly.” These parts are not sold separately.

Milling

Cone

Shaft
with
Nylon
Sleeve

Housing
with Milling
Ring

Handle Knob
Adjustor

Handle Arm

Wood Handle
Grip

Handle Bolt

Nylon

Washer

Housing

Cover

Cover Nut for
Screw Handle Bolt

Rubber Pad

Clamp Cap
Cover

Clamp Cap

3

Keep your work area, all equipment and utensils clean. Before using, dismantle the
grinder and wash all parts in warm, soapy water.

1. Insert the shaft and attached milling cone through the housing.

2. Slip the nylon washer on the end of the shaft.

3. Attach the arm assembly with the handle knob adjustor. DO NOT OVER
TIGHTEN.

U

SING YOUR GRAIN MILL

Mount the Grain Mill on a table or counter top and secure with the clamp screw.
Select the desired texture by turning the handle knob adjustor clockwise for fine
milling or counter-clockwise for a coarser texture. DO NOT OVER TIGHTEN. This
will cause excessive wear and may damage the grain mill. Turn the handle knob
adjustor clockwise until snug, then add grain and begin milling.

C

LEANING YOUR GRAIN MILL

The Back To Basics® Grain Mill is easy to clean. Simply use a brush or cloth to wipe
clean. If a thorough cleaning is needed; wash in warm, soapy water, rinse and dry
thoroughly.

H

ELPFUL HINTS

This product is designed to grind grains and dried nuts. Never put any foreign
objects not intended for this product into the grinder.

Most dried beans and nuts can be ground, but may need to be chopped into smaller
pieces before the grinder will accept them. This can be done easily with a food
chopper or blender.

We do not recommend grinding peanuts or other fresh nuts as they contain too much
oil. This will cause the shaft to bind and ruin the milling cone.

4

L5772 08/08 Back To Basics®, a Brand of Focus Electrics, LLC. Printed in China

P

RODUCT WARRANTY

Appliance 2 Year Limited Warranty

Focus Electrics, LLC (“Focus Electrics”) warrants this appliance from failures in the material
and workmanship for two (2) years from the date of original purchase with proof of purchase,
provided the appliance is operated and maintained in conformity with the provided Instruction
Manual. Any failed part of the appliance will be repaired or replaced without charge at Focus
Electrics’ discretion. This warranty applies to indoor household use only.

This warranty does not cover any damage, including discoloration, to any non-stick surface of
the appliance. This warranty is null and void, as determined solely by Focus Electrics if the
appliance is damaged through accident, misuse, abuse, negligence, scratching, or if the
appliance is altered in any way.

THIS WARRANTY IS IN LIEU OF ALL IMPLIED WARRANTIES, INCLUDING WARRANTIES
OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, PERFORMANCE, OR
OTHERWISE, WHICH ARE HEREBY EXCLUDED. IN NO EVENT SHALL FOCUS
ELECTRICS BE LIABLE FOR ANY DAMAGES, WHETHER DIRECT, INDIRECT,
INCIDENTAL, FORSEEABLE, CONSEQUENTIAL, OR SPECIAL, ARISING OUT OF OR IN
CONNECTION WITH THIS APPLIANCE.

If you think the appliance has failed or requires service within its warranty period, please
contact the Focus Electrics Customer Service Department at [phone], or e-mail us at
[e-mail]. A receipt proving the original purchase date will be required for all
warranty claims, hand written receipts are not accepted. You may also be required to return
the appliance for inspection and evaluation. Return shipping costs are not refundable. Focus
Electrics is not responsible for returns lost in transit.

Valid only in USA and Canada

R

EPLACEMENT PARTS

Replacement parts, if available, may be ordered directly from Focus Electrics, LLC several
ways. Order online at www.focuselectrics.com, e-mail [e-mail], over the
phone by calling [phone], or by writing to:

Focus Electrics, LLC
Attn: Customer Service
P. O. Box 2780
West Bend, WI 53095

To order with a check or money order, please first contact Customer Service for an order total.
Mail your payment along with a letter stating the model or catalog number of your appliance,
which can be found on the bottom or back of the unit, a description of the part or parts you are
ordering, and the quantity you would like. Your check should be made payable to Focus
Electrics, LLC.

Your state/province’s sales tax and a shipping fee will be added to your total charge. Please
allow two weeks for processing and delivery.

This manual contains important and helpful information regarding the safe use and care of your
new Focus Electrics product. For future reference, attach dated sales receipt for warranty proof
of purchase and record the following information:

Date purchased or received as gift: _______________________________________________
Where purchased and price, if known: _____________________________________________
Item number and Date Code (shown bottom/back of product):___________________________