BABYSTYLE Oyster max single, Oyster max tandem Instruction Manual

BabyStyle UK Limited
LE12 7RJ
UNITED KINGDOM

This instruction manual:
© BabyStyle UK Limited 2013
All rights reserved.
OYSTER MAX

LJS/094915122015

register your product at www.babystyledirect.co.uk

Important safety information

Primary features 4-5
Fitting/ removing the front wheels 6
Fitting/ removing the rear wheels 7
Operating the swivel front wheels 8
Adjusting the handle height 8
Using the parking brake 9
Opening the chassis 10
Fitting/ removing the upper seat unit 11
Folding the chassis 12
Folding the chassis with the upper seat unit fitted

Folding the chassis with the upper seat unit fitted 13
Adjusting the seat unit backrest 13
Fitting/ removing the upper carrycot to/ from the chassis 14
Lowering the carrycot hood 14-15
Fitting/ removing the bumper bar 15
Carrycot height adaptors 16
Oyster Max Car seat adaptors 17
Car seat options

Car seat options 17
Fitting/ removing the car seat- upper position 17-18
Using the restraint system (safety harness) 18-19
Fitting the footmuff 20
Fitting the stroller rain cover 20
Fitting the carrycot rain cover 20
Hood/ Sun canopy 21
To fit/remove the seat unit hood 21
Zippered canopy extension and Insect net 22
Fitting the upper seat unit apron 22

Primary features - Tandem 24-25
Fitting/ removing items to/ from the lower position 26
Fitting/ removing the cover plugs

Fitting/ removing the cover plugs 26-27
Fitting/ removing the tandem adaptors 27-29
Fitting/ removing the tandem seat unit 29-30
Fitting/ removing the wheel guards 30
Reclining the tandem seat unit 30
Fitting/Removing the tandem seat hood 31
Adjusting the lower seat leg rest 32

Adjusting the lower seat leg rest 32
Fitting/ removing the lower carrycot 32-33
Fitting/ removing compatible car seats to lower position 33
Fitting/ removing a car seat using lower multi adaptor 34
Tandem safety warnings 34-35
Care and Maintenance/Warranty 36-37

3

CONTENTS

This instruction manual is split into two sections: section one provides instructions
for use of the single Oyster Max stroller, section two provides instructions for use
of the Oyster Max as a Tandem stroller.

1. WARNING: A child’s safety is your responsibility.

2. WARNING: Never leave your child unattended.

3. WARNING: Ensure that all locking devices are engaged before use.

4. WARNING: Do not use a mattress thicker than 35mm.

5. WARNING: Never lift/ carry the chassis while occupied.

6. WARNING: Always descend/ mount kerbs on the back wheels, do
not tip the vehicle forwards.

not tip the vehicle forwards.

7. It is important that any person intending to use this vehicle fully
understands the instructions.

8. WARNING: Use harness at all times.

9. WARNING: Always use the upper and lower seats in the intended
positions.

10. WARNING: Do not use the tandem seat without first fitting the
wheel covers.

wheel covers.

11. Never overload the vehicle; the weight limit for the shopping tray
is 3kg. Always place articles in the centre of the tray provided.

12. This vehicle has been designed for the carriage of one or two
children, one in the upper position and one in the lower position. Do not
attempt to carry more than two children in the vehicle. Upper seat unit
1 child 0 to 15kg, Lower seat unit 1 child 0 to 15 kg, each carrycot
1 child 0 to 9 kg, each car seat 1 child 0 to 13 kg. The Oyster ride

1 child 0 to 9 kg, each car seat 1 child 0 to 13 kg. The Oyster ride
on board has a 20 kg weight limit. Do not overload the stroller.

13. WARNING: This product is not suitable for running or skating.

14. WARNING: Incorrect assembly, folding or use of this vehicle may
cause damage and affect the safety of the vehicle.

15. Do not use accessories that are not approved by the manufacturer.

16. WARNING: Any load attached to the handle affects the stability
of the pram/ pushchair/ stroller.

of the pram/ pushchair/ stroller.

17. WARNING:

Always use the crotch strap in combination with the waist belt.

18. WARNING: Never leave the vehicle without first engaging the
parking device. Avoid uphill or downhill parking.

19. WARNING: Check that the pram body or seat unit or car seat
attachment devices are correctly engaged before use.

20. Do not use replacement parts other than those supplied by the
manufacturer or distributor.

manufacturer or distributor.

21. Do not use the vehicle on steps, stairs or escalators; as it may be
dangerous to your child/ children.

22. Check on a regular basis to make sure that all essential
components & locking devices are functioning correctly.

23. WARNING: To avoid injury ensure that your child is kept away
when unfolding and folding this product.

24. WARNING: Do not let your child play with this product.

24. WARNING: Do not let your child play with this product.

25. Care and maintenance by the user is required to keep
this product operating correctly

.

IMPORTANT SAFETY INFORMATION

IMPORTANT- Read the instructions carefully before use and keep them for
future reference. Your child’s safety may be affected if you do not follow these
instructions.

2

3

SECTION 1

Backrest recline

lever

4

5

Zip for

extendable canopy

Handle grip

Unfolding sliders

Upper seat unit

release handle

Upper seat unit

attachment device

Parking brake

Shopping basket

Front wheel

quick release

Swivel wheel

locks

Footrest

Leg rest

Bumper bar

release button

Rear wheel

quick release

Handle height

adjustment

Bumper bar

Concealed insect/

shade net

Push in the front wheel quick-release button
on the front wheel housing and push the wheel
unit onto the front wheel axle stub until it stops.
Release the quick-release button and check that
the wheel is locked on. To remove the wheel:
Push in the front wheel quick release button on
the front wheel housing and pull the wheel unit

the front wheel housing and pull the wheel unit
from the axle stub. NOTE: The axle stubs can
become greasy and may leave marks on other
surfaces they come into contact with; handle with
care. To keep the front wheels swivelling freely
ensure they are regularly lubricated. If steering
becomes stiff, remove front wheel units, clean,
lubricate and refit.

lubricate and refit.

FITTING/ REMOVING THE REAR WHEELS

Hold the rear wheel and insert the rear wheel
axle stub into the hole in the rear axle. Push
in completely until you hear a click. Pull the
wheel to check it is locked on. To remove the
rear wheel, push in and hold the rear wheel
quick-release lever (on the rear axle) and pull
the rear wheel from the axle. NOTE: The

the rear wheel from the axle. NOTE: The
axle stubs can become greasy and may leave
marks on other surfaces they come into contact
with; handle with care.

Press and hold
rear wheel quick
release lever

FITTING/ REMOVING THE FRONT WHEELS

7

6

Press and hold

wheel release button

Press
DOWN
for
swivel-
wheel
mode

ADJUSTING THE HANDLE HEIGHT

To adjust the handle position: Standing in the
pushing position simultaneously press in the
adjustment buttons located on the inside of each
side of the handle, move handle to one of the pre-
set positions.

USING THE PARKING BRAKE

Lever UP brake OFF

Lever DOWN brake ON

Rotate handle

OPERATING THE SWIVEL FRONT WHEELS

The front wheels can be used in swivel-wheel or
fixed-wheel mode. To switch from locked to swivel:
Press down the swivel wheel lock buttons (left &
right). To switch back to locked; press again and
the wheels will lock automatically when they return
to the travel forwards position.

Press and hold
in buttons on either
side of the handle

8 9

Press
again to
lock the
wheels in
forwards
position

OPENING THE CHASSIS

WARNING: To avoid injury ensure that children
are kept away when unfolding and folding this
product.

To fit the upper seat unit to the chassis: hold
the seat unit by the seat unit release handles
and lower the seat unit into the attachment
devices left and right. Push down until the
seat clicks and locks into position. Ensure
the seat is locked into position by trying to
pull the seat from the chassis. The seat can

pull the seat from the chassis. The seat can
be fitted facing forwards or facing backwards.

Hold the seat unit
by the seat sides
and seat unit release
handles (left and
right) pull the handles
up with your fingers.
The seat will be

The seat will be
released from the
attachment device.

WARNING: never
attempt to fit or
remove the seat
unit while the seat
unit is occupied.

unit is occupied.

WARNING: The
upper seat unit
should only be used
in the upper position.

Pull UP on
release
handles

‘CLICK’

REMOVING THE UPPER SEAT UNIT

FITTING THE UPPER SEAT UNIT

1.

2.

3.

10 11

4.

To fold the chassis there are two steps: It is
important that each step is fully complete before
moving onto the next.

WARNING: It is important when folding the chassis
that the sliders are fully lifted before the whole
handle is lifted up, failure to ensure this
could damage the folding device.

Always ensure the child is clear of moving parts
while making adjustments.

FOLDING THE CHASSIS WITH THE
UPPER SEAT UNIT FITTED

ADJUSTING THE SEAT UNIT BACKREST

Pull both sliders
back simultaneously.

Lift the
handle and
push away
from
yourself

Lift the seat
backrest recline
lever to adjust
backrest angle

FOLDING THE CHASSIS

12

13

FITTING/ REMOVING THE UPPER
CARRYCOT TO/ FROM THE CHASSIS

WARNING: Children should be clear of
moving parts while making adjustments.

The carrycot hood can be lowered (reclined
backwards) by pressing in the two buttons (left &
right) at the outside base of the hood opening.
Push in the buttons and recline the hood. To erect
the hood; lift up the hood until it clicks into position.

Press hood
release buttons
on either side
of hood and tilt
back.

Push the ends of the bumper bar into the
corresponding slots on the seat unit until the
bumper bar locks into position. To remove the
bumper bar, press in the bumper bar release button
on the side of the seat; one right; one left. The
position of the bumper bar can be adjusted by
pressing the buttons on the insides of the bumper

pressing the buttons on the insides of the bumper
bar.

Bumper bar
release button.

Pull UP carrycot
release handles
in arrow direction
to release
carrycot from
chassis.

FITTING/ REMOVING THE BUMPER BAR

LOWERING THE CARRYCOT HOOD

The carrycots can only be fitted to the chassis
when the seat units or car seats have been
removed. The upper carrycot can only be fitted to
the chassis facing the handle. Position the
carrycot so that the fittings in the middle of the
carrycot line up with the upper attachment device
on the chassis. Push the carrycot down until it

on the chassis. Push the carrycot down until it
clicks into position. Check that the carrycot is
securely attached by trying to lift the carrycot from
the chassis.

To remove the carrycot from the chassis: Hold the
carrycot by the two release handles, and pull the
handles up with your fingers. The carrycot will be
released from the attachment device.

released from the attachment device.

14

Press buttons on the inside
of the bumper bar to rotate.

15

REMOVING

FITTING

The Oyster car seat (LB321) is fitted to the Max
chassis by using the LB321 Oyster car seat
adaptors. The car seat can not be attached to the
chassis until the seat unit or the carrycot has
been removed.

Insert the car seat adaptors into the car seat, by
pushing them into the cavity on the underside of

pushing them into the cavity on the underside of
the sides of the carry handle, the adaptors are
marked “R” and “L” for right and left. Push the
adaptors up until they click and lock into position.
Hold the car seat by the carry handle and lower the
car seat onto the chassis until the adaptors fit into
the upper attachment device. Push the car seat
down firmly until the car seat clicks and locks into

down firmly until the car seat clicks and locks into
position. Check that the car seat is secure by
pulling up on the car seat handle.

To remove the car seat from the chassis; pull
up the release handles located on either side
of the car seat on the adaptor and lift the car
seat away from the chassis. The release
handles are shown in the image on page 16
and described as recessed handles in the
image on page 18.

image on page 18.

The Oyster Max carrycot and selected car seats
(see table page 18) can be raised in height by use
of the height adaptors.

To fit the height adaptors; insert the adaptors
(marked L for left and R for right) into the
attachment device and ensure they are locked into

attachment device and ensure they are locked into
position. Lower the carrycot or car seat onto the
adaptors and press down. Check that the carrycot
or car seat is secure and locked by trying to lift
away from the chassis. To remove the carrycot or
car seat; hold the item by the two release handles,
and pull the handles up with your fingers. The item
will be released from the height adaptors. The

will be released from the height adaptors. The
height adaptors can then be removed from the
chassis by lifting the lever located on the short
edge of the adaptor and pulling the adaptor away
from the chassis.

Height adaptors

CARRYCOT/ CAR SEAT HEIGHT
ADAPTORS (Optional)

REMOVING THE OYSTER CAR SEAT
(LB321) FROM THE MAX CHASSIS - UPPER

FITTING THE OYSTER MAX CAR SEAT
(model LB321) TO THE CHASSIS - UPPER

Removing the car seat

Fitting the car seat

Push into slot

Fitting the adaptors

Carrycot with height adaptor

Carrycot without height adaptor

16

17

Pull up release
handle

Locate adaptor
in upper
attachment
device

FITTING THE Britax BABY-SAFE for OYSTER
CAR SEAT UPPER POSITION

The car seat cannot be attached to the chassis
until the seat unit or the carrycot has been removed.
Insert the Britax car seat adaptors into the car seat
following the instructions provided with the Britax
car seat, these adaptors need to be inserted one
time and are then integral to the seat unit. Insert
the carrycot/ car seat height adaptors into the

the carrycot/ car seat height adaptors into the
chassis attachment device. Hold the car seat by
the carry handle and connect the fittings on the car
seat with the carrycot/ height adaptors. Push the
car seat down firmly until it clicks and locks into
position. Check that the car seat is secure and
locked by pulling up on the car seat handle.

REMOVING THE Britax BABY-SAFE for OYSTER
CAR SEAT

Hold the car seat by the recessed handles in the
adaptors located below the base of the car seat
carry handle. Pull up on the two adaptor handles
and lift the car seat away from the chassis.

To remove the car seat from the chassis: Pull up
the release handles located on either side of the car
seat on the adaptor and lift the car seat away from
the chassis. The release handles are shown in the
image on page 18 and described as recessed
handles.

The Oyster Max chassis can be combined with car
seats from other leading brands. For details, see
the table below. Always check with your retailer
that you have the correct car seat adaptors if
adaptors are required.

OYSTER MAX CAR SEAT ADAPTORS

Oyster (LB321)

Car seat adaptor

Oyster Multi car

seat adaptors

Oyster Max Lower

Multi car seat

adaptors

with straps

Recessed handles for removing car seat adaptors from chassis.

CAR SEAT OPTIONS

REMOVING A CAR SEAT WHEN FITTED WITH
THE MULTI ADAPTORS - UPPER POSITION

The car seat can not be attached to the chassis
until the seat unit or the carrycot has been removed.
Insert the car seat adaptors into the cavity on the
underside of both sides of the handle on the car seat,
the adaptors are marked “1” and “2”; 1 is right and
2 is left.Push the adaptors until they click and lock
into position. Hold the car seat by the carry handle

into position. Hold the car seat by the carry handle
and lower the car seat onto the chassis, so that the
adaptors locate into the upper attachment device.
Push the car seat down firmly until the car seat
clicks and locks into position. Check that the car
seat is secure and locked by pulling up on the car
seat handle.

FITTING A CAR SEAT USING MULTI
ADAPTORS - UPPER POSITION

18

19

Always apply the parking brake before placing your
child in the vehicle. The restraint system (safety
harness) has two shoulder straps, a circular waist
belt and a crotch strap. Place the two shoulder
straps over the child’s shoulders and the waist belt
around the child’s waist. The crotch strap should be
placed between the child’s legs. The waist belt &

placed between the child’s legs. The waist belt &
shoulder straps should be clipped into the centre
buckle at the end of the crotch strap.

The harness can be adjusted to suit your child by
sliding the adjusters along the shoulder straps and
waist belt. To release the safety harness, push the
buttons on the centre buckle. D-rings for attaching
a separate harness can be found attached to the

a separate harness can be found attached to the
integral harness at the base of the waist straps.
The crotch strap can be adjusted to suit your child.
There are two button holes in the seat base.
Thread the buckle through the hole in the plastic
seat base and then through the opening in the seat
covers and reposition, passing back through first
the seat cover and then through the opening in the

the seat cover and then through the opening in the
plastic seat base. The shoulder straps can be
adjusted to two height positions; thread the buckle
through the hole in the plastic seat back and
through the opening in the seat cover and
reposition passing first through the seat cover and
then through the opening in the plastic seat back.
Ensure that both shoulder straps are at the same

Ensure that both shoulder straps are at the same
level and that both are secure.

with comfort pads fitted

USING THE RESTRAINT SYSTEM
(SAFETY HARNESS)

Shoulder

strap and

buckle

Waist belt

and buckle

Waist belt
and buckle

Crotch
strap
buckle

Centre
harness
buckle

Shoulder
strap and
buckle

WARNING: Always
use the crotch strap
in combination
with the waist belt.

ALWAYS USE THE
RESTRAINT SYSTEM
(SAFETY HARNESS).

(SAFETY HARNESS).

FITTING THE FOOTMUFF

The footmuff top cover can be removed by
unfastening the zip. The base of the footmuff can
be used as a seat liner without the top part. To
attach the footmuff to the seat unit: Release the
harness clips from the centre buckle and release
the shoulder straps from the waist belts at the
buckle connection. Pass the shoulder straps and

buckle connection. Pass the shoulder straps and
waist belts through the corresponding openings in
the footmuff. Pass the crotch strap through the
opening in the footmuff.

FITTING THE STROLLER RAIN COVER

The rain cover needs the stroller hood to be fitted
to support it. For the upper seat; Place the rain
cover over the back of the seat unit hood; Fasten
the Velcro strips at the front of the rain cover
around the front legs of the chassis (when the seat
unit is facing forwards). When the seat unit is
facing rearwards, fasten the Velcro strips at the

facing rearwards, fasten the Velcro strips at the
front of the rain cover around the rear legs to
secure. For the lower seat: place the rain cover
over the front of the seat unit leg rest and stretch
over the seat unit towards the hood. Pull over the
back of the hood to secure.

FITTING THE CARRYCOT RAIN COVER

With the carrycot hood in the upright position, place
the rain cover over the hood so that the flap on the
rain cover corresponds with the opening in the carry
cot hood. Pull the rain cover down to the rear of
the hood so that the elasticated edge covers the
rear of the carrycot. Ease the front part of
the rain cover over the apron and down and

the rain cover over the apron and down and
around the front and sides of the carrycot.

20

21

The Oyster Max (upper seat) has a multi-function
hood that helps to protect your child from the
elements. The hood is extendable and has a
viewing window. The hood can also be removed
altogether.

TO REMOVE/ FIT THE HOOD

To maximise the hood coverage there is a zippered
section in the middle of the upper seat unit hood.
Unfasten the zip and extend the hood. Fasten the
zip to reduce the hood coverage.

The upper seat unit has an integrated insect shade
net concealed in a zippered pocket underneath the
leg rest. Unfasten the zip and unfurl the insect net.
The elasticated top part of the insect net attaches
over the hood frame. There are two press-stud tabs
on the sides of the net which fasten to press-studs
on the seat backrest. To stow the insect net; fold

on the seat backrest. To stow the insect net; fold
neatly and place in the zippered opening before
closing the zip; being careful not to catch the net in
the zip. The net can be removed completely by
unfastening the press-stud in the zippered pocket.
A UPF 50+ sun shade black out net is available as
an optional accessory; please contact your local
retailer.

retailer.

FITTING THE UPPER SEAT UNIT APRON

To remove the hood:

To fit the hood:

Place the bottom part of the apron over the leg rest.
The press-studs at the side of the apron allow the
apron to be fastened around the bumper bar. Pass
the top of the apron under the bumper bar and
fasten the press-studs at the top of the apron to the
corresponding press-studs on the back of the seat
backrest. To remove the apron, release the press-

backrest. To remove the apron, release the press-
studs and take away.

INSECT SHADE NET

ZIPPERED CANOPY HOOD EXTENSION

HOOD/ SUN CANOPY

22 23

Shopping basket

Shopping basket

24 25

SECTION 2

Rear wheel

quick release

Lower attachment

device

Upper attachment

device

Unfolding sliders

Handle grip

Lower seat unit

release handle

Wheel guards

Zip for

extendable canopy

Upper seat backrest

recline lever

Bumper bar

Bumper bar

release button

Leg rest

Footrest

Swivel wheel

locks

Front wheel

quick release

Parking brake

Upper seat unit

release handle

Lower seat

backrest

recline lever

Handle height

adjuster

Concealed insect/

shade net

FITTING/ REMOVING ITEMS IN THE
LOWER POSITION

Fitting items in the lower position on the Oyster Max
chassis requires three processes: The removal of
the plugs, the fitting of the tandem adaptors and the
fitting of the item. The wheel guards must also be
fitted when the second seat is in use. Car seats may
require additional adaptors: See table on page 18
for details.

for details.

There are three items that can be fitted in the lower
position on the Oyster Max chassis: The lower
(Tandem) seat unit, carrycot or a car seat.

FITTING/ REMOVING THE COVER PLUGS

To fit the plugs when the lower position is no longer
in use; push the block into the corresponding
aperture until the button clicks into place.

To remove the plugs from the rear of the chassis; Press
the button located on the inside rear of the chassis
behind the brake bar. Lift out the plug from the slot,
repeat this action on both sides of the chassis. This
aperture is where the tandem adaptors will be fitted.

Remove the cover
plug from the aperture.

The plugs are the plastic blocks that fill the aperture
where the tandem adaptors locate. They act as cover
plugs when the lower position is not in use. To fit items
in the lower position, the plugs have to be removed.

FITTING/ REMOVING THE TANDEM ADAPTORS

The lower position requires tandem adaptors to
allow either the lower seat unit, the carrycot or a
car seat to fit the Oyster Max chassis.

To fit the adaptors:
Step 1. Remove the cover plug as described on
page 26.

Step 2. Place the hooked end of the adaptor over

Step 2. Place the hooked end of the adaptor over
the adaptor boss and insert the adaptor into the
corresponding aperture. Image 3 on page 28,
shows the tandem adaptor located in the correct
position on the Oyster Max chassis.

26

B

27

A

Press in ‘A’
Lift up ‘B’

WARNING: The upper seat unit should never be
used in the lower tandem position.

Adaptor
attachment
boss.

Adaptor
attachment
aperture.

1.

Put hook
over adaptor
attachment
boss.

FITTING/ REMOVING THE TANDEM SEAT UNIT

To fit the seat unit, the tandem adaptors need to be
fitted.

To fit the seat unit to the chassis: Hold the seat at
either side of the backrest and lower the seat unit
into the tandem adaptors left and right. Push down
until the seat clicks and locks into position. Ensure
the seat is locked into position by trying to pull the

the seat is locked into position by trying to pull the
seat from the chassis. The seat can only be fitted
in the forward facing position.

To remove the seat unit from the chassis: Press in
the release lever adjacent to the attachment device
left and right, then lift away from the chassis.

WARNING! To avoid injury ensure that children are
kept away when adjusting this product.

kept away when adjusting this product.

To remove the tandem adaptors; locate the adaptor
release button on the inside of the adaptor
attachment device. Simultaneously press in the
button whilst lifting the adaptor clear of the slot and
away from the adaptor attachment boss.

Simultaneously push-
in the button and lift
the adaptor from the
lower seat attachment
aperture and boss.

2.

Tandem
adaptor fitted in
correct position.

3.

Push adaptor
down to fit into
the adaptor
attachment
aperture.

28

29

To recline the seat unit: Locate the lever on the rear
of the backrest and lift up before reclining
backwards,To return to the upright position, with the
lever lifted, push the seat forwards.

FITTING THE WHEEL GUARDS

TO FIT

FITTING/REMOVING THE TANDEM SEAT HOOD

To fit the seat hood; Locate the hood attachment
housing on the seat unit. Insert the fittings on the
hood into the corresponding housings on the seat
unit (1) until they click and lock. With the hood frame
reclined pull the hood fabric over the back of the seat.
(2) Fasten the press-studs on the hood to the seat

(2) Fasten the press-studs on the hood to the seat
unit. Once fitted check the hood is secure.

To remove the hood; (3) Unfasten the press studs,
left and right. Press in the button located on the hood
attachment fittings and remove the hood.

1.

2.

TO FIT

3.

TO REMOVE

RECLINING THE TANDEM SEAT UNIT

TO REMOVE

To fit the individual wheel covers: Push the wheel
cover into the front of the wheel until the
attachment tabs clip into place on the wheel rim
and spokes

WARNING: Do not use the tandem seat without
first fitting the wheel covers

30

31

ADJUSTING THE TANDEM SEAT LEG REST

There are two positions for the leg rest. To elevate
the leg rest to the higher position: Lift both sides of
the leg rest until they locate in the higher position.
To adjust the leg rest to the lower position: Press
the leg rest release buttons (left and right) and
lower the leg rest until it locates in the lower

lower the leg rest until it locates in the lower
position.

TO ELEVATE

TO LOWER

32 33

FITTING/ REMOVING THE LOWER CARRYCOT

To fit the carrycot in the lower position the tandem
adaptors have to be fitted by following the
instructions in the sections ‘fitting/ removing the
cover plugs’ and ‘fitting/ removing the tandem
adaptors.’The carrycot can only be fitted to the
chassis when the seat unit or car seat has been
removed. The lower carrycot can only be fitted to

removed. The lower carrycot can only be fitted to
the chassis facing away from the handle. Lower the
carrycot so that the fittings in the middle of the
carrycot line up with the lower position adaptor.
Push the carrycot down until it clicks into position
as shown in image 1. Check that the carrycot is
securely attached by trying to lift the carrycot from
the chassis.

the chassis.

1.

To remove the lower carrycot from the chassis:
Hold the carrycot by the two release handles and
pull the handles up with your fingers. The carrycot
will be released from the attachment device.

Pull UP carrycot release
handles in arrow direction to
release carrycot from chassis.

FITTING/ REMOVING COMPATIBLE CAR
SEATS TO THE LOWER POSITION.

The Oyster car seat along with compatible car
seats can be fitted in the lower position on the
Oyster Max chassis. Instructions detailing
compatible car seats and methods for fitting can be
found on pages 16-19 and 34.

WARNING: The car seat can only be fitted in the
lower position facing away from the pushing

lower position facing away from the pushing
position.

Carry cot in the
upper position with
the Tandem seat.

Always ensure the child is clear of moving parts
while making adjustments.

Webbing strap

Press stud

Loop the webbing straps
left and right over the car
seat belt guides so that
the press-studs face
outwards. (Maxi Cosi
Pebble only).

Insert the Multi Lower car

Insert the Multi Lower car
seat adaptors into the
tandem adaptors & check
they are secure. Push the
car seat onto the Lower
adaptors until it locks into
position, the car seat
should be facing forwards.

should be facing forwards.
Connect the press-studs
on the lose ends of the
webbing straps to the
corresponding press-
studs on the inside rear
legs of the chassis.

Note: The webbing straps should be used with the
Maxi Cosi Pebble car seat.

Upper seat unit rear
facing with car seat
in the lower position

Oyster Car Seat
Maxi Cosi Pebble
Maxi Cosi CabrioFix
Britax Baby-Safe
BeSafe iZi Go

BeSafe iZi Go
Kiddy Evo Lunafix
Cybex Aton 2,3 & Q

Upper seat unit
forward facing with
car seat in the lower
position

Oyster Car Seat
Maxi Cosi Pebble
Maxi Cosi Cabriofix

Maxi Cosi Cabriofix
Britax Baby-Safe
BeSafe iZi Go
Kiddy Evo Lunafix
Cybex Aton 2,3 & Q

FITTING/ REMOVING A CAR SEAT USING THE
LOWER MULTI ADAPTOR

TANDEM SAFETY WARNINGS

34

35

CARE AND MAINTENANCE

• Do not expose your stroller to excessive sunlight for
extensive periods of time, even normal exposure to
sunlight may cause the colour of the fabric to change.

• Take care not to tear the fabrics while transporting
the stroller.

• Light oil or silicone spray is suitable to use as a
lubricant for moving parts. Petroleum jelly is a good

lubricant for moving parts. Petroleum jelly is a good
lubricant to use on the front axle stubs. Periodically
remove the front swivel wheel units clean and
lubricate with petroleum jelly.

• Ensure that zips are either fully open or fully closed
or they may be damaged.

• Always use the rain covers in inclement weather.

•• Do not place items on the hood/canopy, it may
damage the vehicle and/or render it unsafe.

• Rubber tyres can leave marks on some surfaces.
The tyres can react with some surfaces (vinyl floor
coverings, carpets etc.) and cause stains. Always
stand the stroller on a protective surface indoors.

• Routinely clean the metal parts with a damp cloth
& then dry immediately.

& then dry immediately.

• Fabrics should be cleaned following the guidance
on the care labels.

• DO NOT WASH IN THE WASHING MACHINE.
Sponge clean only with mild detergent and warm
water (30°C).

• Regularly check screws, rivets, bolts & fastenings
to ensure they are locked tight and secure. Replace
any parts in an inferior condition. Should you intend
to use this product during the winter, by the sea or
off-road; it is important to clean thoroughly & dry the
vehicle after use. Salt from the ocean or from roads
will corrode metal parts unless removed. After use will corrode metal parts unless removed. After use
in these circumstances clean with fresh water and
thoroughly dry after use.

• Check on a regular basis that all chassis locking
devices are working correctly.

• If any part of the product is damaged contact your
local BabyStyle retailer immediately without using
the product.

the product.

36

37

A stroller has many moving parts and requires

regular maintenance by the user. Simple cleaning

and lubricating will make the stroller look good &

operate better for longer. The stroller will be used

in many different environments, country walks, a trip

to the coast; a winter’s walk to school, all can

increase wear; lead to rust and corrosion and reduce

increase wear; lead to rust and corrosion and reduce

the life of the product. Regular cleaning; care and

maintenance will reduce the effects of the

environment on the stroller. The warranty does not

protect the stroller against overloading, misuse,

neglect or lack of care and maintenance by the user.

BabyStyle UK Ltd. provides a warranty in support of

the retailer from whom you purchased this product.

the retailer from whom you purchased this product.

The warranty is effective for 12 months from the date

of purchase for the original purchaser/owner.

Proof of purchase will (at the discretion of BabyStyle

UK Ltd.) be required in order for your retailer to claim

on the warranty. The warranty excludes any fault

caused by misuse, accidental damage or neglect.

It is the user’s responsibility to undertake routine

It is the user’s responsibility to undertake routine

inspection and maintenance of the vehicle in order

to avoid damage to the vehicle and/or injury to the
child. The vehicle is returned to the retailer at the

owner’s expense in order to ascertain if a claim

under the warranty is justified. Please carefully

read the instructions on how to look after your

stroller. This does not affect your statutory

stroller. This does not affect your statutory

rights.

WARRANTY