How it Works
BABYSTYLE
Loading...
LUX TWIN CLASSIC

BABYSTYLE Lux 3 in 1, Lux 2 in 1, LUX TWIN CLASSIC Operating Instructions Manual

Download
This manual applies to the following models
LUX 3 in 1, LUX 2 in 1 & LUX TWIN CLASSIC
OPERATING INSTRUCTIONS
IMPORTANT: Read these instructions carefully before use and keep them for further
reference. Your child’s safety may be affected if you do not follow these instructions.
2
www.implast.com.pl
IMPORTANT – Please read these instructions carefully before using your new pram / pushchair. Keep this manual in a safe place for future reference. This product complies with TÜV and British Standard BS 7409: 1996.
Important Safety Information
• WARNING: A child’s safety is your responsibility
• WARNING: Children should never be left unattended in this vehicle.
• It is important that any person intending to use this vehicle fully understands the instructions.
• WARNING: Children should be harnessed in this vehicle at all times. Use the
ve point harness that is provided, make sure the harness is securely fastened
to the “D-rings” situated on the chassis either side of the seat. Adjust the harness to its correct position with the use of the adjustable straps.
• WARNING: Children should always be kept clear of moving parts while making adjustments to the vehicle.
• Never overload the vehicle. Maximum weight of child should not exceed 15 kg. The weight limit for the shopping tray is 3 kg. Always place articles in the centre of the tray provided. Any load attached to the handle will adversely affect the stability of the vehicle.
• WARNING: Incorrect assembly, folding or use of this vehicle may cause damage and affect the safety of the vehicle.
• It may be unsafe to use accessories (e.g. child seats, bag hooks, rain covers etc.) other than those approved by the manufacturer.
• WARNING: Never leave the vehicle without rst engaging the parking device.
Avoid uphill or downhill parking.
• Avoid using the vehicle on steps, stairs or escalators as it may be dangerous to your child/children.
• Check on a regular basis to make sure that all essential components & locking devices are functioning correctly.
• When the pram body is used , the depth from the top of the mattress to the top of the side of a body at, or at any position within 300 mm from, the har­ness attachment points, should not be reduced to less than 140mm when the mattress is in position. Any mattress purchased separately should conform to BS1877: Part 10 .
• Do not use replacement parts other than those supplied by the manufacturer or distributor.
• Never use this vehicle as a permanent bed for your child / children. BS 7409: 1996 label
WARNING: A CHILDS SAFETY IS YOUR RESPONSIBILITY.
Children should be harnessed in at all times and should never be left unattended. The child should be clear of moving parts while making adjustments. This vehicle requires regular maintenance by the user. Overloading, incorrect folding and the use of non-approved accessories may damage or break this vehicle. Read the manufacturer’s instructions.
2
3
www.implast.com.pl
WARNING: This pram has been designed to be operated as shown in the instructions. Failure to follow these instructions may cause damage and render the guarantee void.
Fitting/Removing the wheels
• To t the wheels. Turn the chassis on its
side and gently slide the wheel on to the axle until it stops, now depress the steel clip (found in the centre hub of the wheel) until the wheel drops further on to the axle and stops. Release the steel clip and slide the wheel back (as if removing) until the wheel locks into position (Picture 1).
Check that the wheels are tted securely
before use.
• To remove the wheels, depress the
metal clip while simultaneously easing the wheel off with a twisting action. Care
should always be taken when tting &
removing wheels.
2.
Unfolding the chassis
• To erect the chassis apply the parking
device; pull the handle upwards and over following the direction of the arrow (Picture 2). Check that the two sliders on either side of the chassis are locked in position (Picture 3).
3
3.
1.
PNEUMATIC TYRES: Please note that pneumatic tyres; by their nature are prone to puncture, punctures can be repaired with a standard puncture repair kit or the inner-tube can be replaced. Remember that rubber tyres can leave marks on some surfaces (see General Care & Maintenance).
4
www.implast.com.pl
Attaching the seat unit or pram body
• Tilt the seat unit or pram body
forward and locate the two front pegs in the attachment mechanism (no. 1, Picture 4). Gently push down until the two pegs lock into position; now tilt the unit backward until the rear attachment pegs lock into the rear attachment mechanism (no.2, Picture 4). ENSURE THAT THE SEAT UNIT OR THE PRAM BODY IS SECURELY FITTED BEFORE USE.
• To remove the seat unit
or pram body. Gently apply downward pressure to the seat frame or pram body & then push the red attachment mechanism lever (no.1, Pictrue 5) forward until it stops, repeat this action on the opposite side. Standing in the pushing position; tilt the seat or bassinet unit upward until the two forward attachment pegs are released from the attachment mechanism; now slide the two rear pegs from their attachments and lift the unit clear of the chassis.
Pram body sit-up board
The pram body is equipped with a sit-up board. The sit-up board is for use as a back rest when your child is ready to sit up. The sit-up board can be erected/reclined to three positions
or folded at into the sleeping position.
To erect the sit-up board lift the top of the sit-up board and locate the support bar (at the back of the sit-up board) in the desired position. The support bar locates in the plastic housings on the inside base of the pram body. To recline the sit-up board; release the support bar and recline the sit-up board back rest (Picture 6).
4
4.
5.
6.
5
www.implast.com.pl
Fitting the hood Seat Unit/ Pram Body
• To attach or remove the hood.
Push the hood bracket into the plastic housing until it clicks (Picture 7).
• To remove the hood, depress the
plastic latch at the bottom of the bracket and pull upwards.
NOTE : Some models are supplied (depending on design) with a valance
that ts via a zipper to the rear bottom
edge of the hood. The valance is designed for use with the hood when used in conjunction with the seat unit.
Fitting the front bar
• To attach front bar, push the front
bar bracket into the plastic housing until it clicks (Picture 8).
• To remove the front bar, depress
the plastic latch at the bottom of the bracket and pull upwards simultaneously.
Adjusting the seat unit backrest
• To adjust the position of the seat unit
backrest, support the seat back in one hand press-in button (picture no 9.). While holding the button in; reposition the backrest as desired and release the button. The backrest has 5 usable positions.
5
Adjusting the seat unit backrest
(Twin Classic only)
• To recline an individual seat unit
backrest, gently pull the bar in the middle of the back of the seat backrest, recline the seat to one of its three positions and release the bar, the seat will automatically drop into position.
8.
9.
7.
6
www.implast.com.pl
Adjusting the footrest
• To adjust the footrest press the two
buttons on the top of the footrest and lift or lower the footrest to the desired position (Picture 11).
Adjusting the handle
• To regulate handle, simultaneously
push the two buttons of the handle height adjuster and rotate the handle to the desired position (Picture 12).
Operating the brake
• To engage the parking device, push the
lever down with your foot until it locks
into position. Avoid uphill or downhill
parking. Never let go of the handle. To release the brake, lift up with your foot (Picture 13).
6
10.
11.
12.
13.
Fitting the bed extension
• To attach the bed extension, remove
front bar, set the footrest to horizontal
position (see Adjusting the footrest) and push the bed extension brackets into the plastic housing until it clicks. To remove the bed extension, depress the plastic latches at the bottom of the bracket and pull upwards simultaneously (Picture 10).
Fitting the head hugger
(Twin Classic only)
• To t the head hugger (remove the
hood if tted); attach the press-studs on
the head hugger to the corresponding press-studs on the rear outside part of the seat unit armrests. Replace the hood. Note: The base fabric of the head hugger should always be behind the seat unit backrests
.
7
www.implast.com.pl
Folding the chassis
• To fold the chassis, pull back the two
sliders on either side of the chassis handle & release the secondary safety catch, gently let the chassis close (Picture 14). Using the handle height adjusters; fold the handle back on itself to make the folded chassis more compact (Picture 15).
Safety harness
•
Always apply the parking brake before placing your child in the vehicle.The safety harness has two shoulder straps, two waist belts and a crotch strap. Place the two shoulder straps over the child’s shoulders and the waist belts around the child’s waist, the crotch strap should be placed between the child’s legs. The shoulder straps and the waist belts should be clipped into the buckle at the end of the crotch strap (Picture 16).
The harness can be adjusted to suit your child by sliding the adjusters along the shoulder straps and waist belts.To release the safety harness, push the bottons on the centre buckle. D-rings for attaching a separate harness conforming to BS 6684 can be found on either side of the seat frame near the backrest and seat base hinge.
7
15.
14.
SAFETY CATCH
Fitting/removal of Britax car seats to the LUX chassis
(Excludes Twin Classic)
The Lux can be tted with the following Britax Infant Carriers: Babysure and
Rock -a-Tot Plus SI
•
To attach the car seat adaptor frame to the chassis place the frame so that all four pins rest in the attachment devices. Push the frame down until the frame clicks and locks into position. The adaptor frame should be orientated so that the bend in the adaptor frame is upwards and the thinnest cross bar of the adaptor is closest to the handle end of the chassis. Rest the car seat on the adaptor and allow the two slots on the car seat rockers to locate on the thin cross bar. Fasten the locking clip (located at the rear of the car seat backrest) around the adaptor frame. Check that the adaptor is securely attached to the chassis and that the car seat is securely attached to the adaptor before use. Refer to the Britax car seat USER GUIDE for further information
on harness use and tting the infant carrier into a car. To remove the car seat from
the adaptor; release the clip at the rear of the seat and lift the car seat upwards and clear of the adaptor frame. The adaptor frame can be removed from the chassis by following the procedure for removing the seat unit or pram body.
16.
HOW TO LOOK AFTER
YOUR PRAM/PUSHCHAIR
• Routinely clean the metal parts with a damp cloth and then dry immediately.
• Fabrics should be cleaned using lukewarm water and a mild detergent. Do not use aggressive cleaning agents. Do not wash in the washing machine.
• Regularly check screws, rivets, bolts & fastenings to ensure they are locked tight and secure. Replace any parts in an inferior condition. Should you intend to use the pushchair during the winter, by the sea or off-road; it is important to clean thoroughly & dry the vehicle after use. Salt from the ocean or foam roads will corrode metal parts if the vehicle is not cleaned after use.
• Check on a regular basis that all chassis locking devices are working correctly.
• If any part of the pushchair is damaged contact your local Babystyle retailer immediately without using the pushchair.
• Petroleum jelly is suitable to use as a lubricant.
• Ensure that zips are either fully open or fully closed or they may be damaged.
• Always use a rain-cover in inclement weather.
• Do not place items on the hood/canopy, it may damage the vehicle and/or render it unsafe.
• Rubber tyres can leave marks on some surfaces. The tyres can react
with some surfaces ( vinyl  oor coverings, carpets etc.) and cause stains.
Always stand the stroller on a protective surface indoors.
• Do not expose your pushchair to excessive sunlight for extensive periods of time & take care not to tear the fabrics while transporting the pushchair.
WARRANTY
Babystyle UK Limited provides a warranty in support of the retailer from whom you purchased this product. The warranty is effective for 6 months from the date of purchase for the original purchaser/owner. Proof of purchase will ( at the discretion of Babystyle UK Limited) be required in order for your retailer to claim on the warranty. The warranty excludes any fault caused by misuse, damage or neglect. It is the user’s responsibility to undertake routine inspection and maintenance of the vehicle in order to avoid damage to the vehicle and/or injury to the child. The vehicle is returned to the retailer at the owner’s expense
in order to ascertain if a claim under warranty is justi ed. Please read the
instructions carefully to look after your stroller.
BabyStyle UK Ltd.
36 Charles Street, Sileby, Leicestershire, LE12 7RJ
Tel: 01509 816444 Fax: 01509 816555
Email: info@babystyle.co.uk
www.babystyle.co.uk
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use