BaBylissPro BAB831C Operating Instructions Manual

DIRECTIVES

D'UTILISATION

Modèle BAB831C

Tondeuse de finition

rechargeable

professionnelle

Afin que votre appareil vous

procure en toute sécurité

beaucoup de satisfaction,

lire attentivement le mode

d'emploi avant de l’utiliser.

OPERATING

INSTRUCTIONS

Model BAB831C

Professional

Cord/Cordless

Trimmer

For your safety and continued
enjoyment of this product,
always read the instruction
book carefully before using.

BAB831C IB-11_631C.indd 1-2 1/28/15 2:27 PM

IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances, basic precautions should always be followed,
including the following:

READ ALL INSTRUCTIONS BEFORE USING

KEEP AWAY FROM WATER

DANGER -

To reduce the risk of electric shock:

1. Do not reach for an appliance that has fallen into water. Unplug immediately.

2. Do not use appliance while bathing or in a shower.

3. Do not place or store appliance where it can fall or be pulled into a tub or sink. Do
not place in or drop into water or other liquid.

4. Always unplug this appliance from the electrical outlet immediately after using.

5. Unplug this appliance before cleaning or putting on or taking off parts.

6. Except when charging, always unplug this appliance from electrical outlet
immediately after using.

7. Always verify rating before plugging in adaptor.

DO NOT REACH INTO THE WATER

WARNING - To reduce the risk of burns, electric shock, fire, or injury to persons:

1. Do not pull, twist, or wrap line cord around appliance. Continuous stress on
cord can damage cord insulation and result in shock.

2. This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.

3. Children should be supervised to ensure that they do not play with the appliance.

4. Keep out of reach of children.

5. Never operate this appliance if it has a damaged cord or plug, if it is not
working properly, or if it has been dropped or damaged, or dropped into
water. Return the appliance to a service center for examination and repair.

6. An appliance should never be left unattended when plugged in.

7. This appliance should not be used by, on, or near children or individuals with
certain disabilities.

8. Use this appliance only for its intended use as described in this manual.
Do not use attachments not recommended by the manufacturer.

9. Keep the cord away from heated surfaces.

10. Never operate the appliance with the air openings blocked, or while it is on a soft
surface, such as a bed or couch, where the air openings may be blocked. Keep the
air openings free of lint, hair and the like.

11. Never drop or insert any object into any opening.

12. Do not use outdoors or operate where aerosol (spray) products are being used, or
where oxygen is being administered.

13. Do not use this appliance with a damaged or broken comb or with teeth missing from
the blades as injury may occur. Before use, make certain blades are aligned properly.

14. To disconnect, turn all controls to “O-OFF,” then remove plug from outlet.

15. Do not place the appliance on any surface while it is on.

16. Avoid skin contact with moving blades.

17. Be mindful of tangles or kinks in the cord. If the cord does become tangled during
use, turn the unit off and straighten cord before operating again.

18. Keep lubricating oil away from children and pets (see warning on the oil tube).

19. Keep the appliance dry.

20. If the supply cord is damaged, it must be replaced by the manufacturer, its service

agent or similarly qualified persons in order to avoid a hazard.

21. Do not short the polarity (output cord), ensure jack is plugged into the unit before

plugged the adaptor into outlet.

22. This power unit is intended to be correctly oriented in vertical or floor-mount

position.

23. For connection to a supply not in the U.S.A., use an attachment plug adaptor of the

proper configuration for the power outlet.

24. Make sure voltage selector is in correct position before plugging unit in.

SAVE THESE INSTRUCTIONS

BAB831C IB-11_631C.indd 3-4 1/28/15 2:27 PM

OPERATING INSTRUCTIONS

1. Before using the appliance for the first time, charge continuously for 16

hours. Maximum battery capacity will only be reached after 3 charging and
discharging cycles.

2. Make sure the switch is in "0-OFF" position. Plug the charging jack into the

receptacle at the back of the charging base. Plug the adaptor into an electrical
outlet. The LED indicator will light up to indicate that charging has begun.

3. After recharging or use, store the appliance in a dry place and keep away from

children.

4. Do not wrap the cord around the appliance or the charging base.

5. Preserving the battery: In order to maintain the optimum capacity of rechargeable

battery, the appliance should be recharged for 16 hours approximately every 3
months.

6. Unplug the outlet adaptor after use.

7. This power unit is intended to be correctly oriented in a vertical or floor-mount

position.

8. CAN ICES-3 (B)

HOW TO CHARGE AND USE AS RECHARGEABLE UNIT

Plug the charging jack into the receptacle at the back of the charging base. Plug
the outlet adaptor into the power socket and place the trimmer into the charging
base. When the LED indicator lights up, the unit is charging. The switch should be in
"O-OFF" position when charging. After the unit is fully charged, remove it from the
charging base and switch to "l-ON" position to operate.

FOR DIRECT PLUG IN OPERATION

Make sure the switch on the trimmer is in "0-OFF" position. Plug charging jack into the
receptacle at the bottom of the unit and plug the outlet adaptor into the power socket.
Allow 2 to 3 minutes for the battery to kick over. Switch to "l-ON" position to operate.

OPERATION

Before using the Class 2 Power Supply, read these instructions carefully.
This trimmer (BAB831C) uses with CA01M adaptor (included) only.
Input: 100-240 V AC 50/60Hz 0.2A Max
Output: 3.0V DC 1000mA

IMPORTANT NOTE:

1. Never operate this unit if the specification is out of the rating.

2. This unit may become warm during use. This is normal.

Charging Base

Comb At tachment and

Blade Guard Holder

Lubricating Oil

Cleaning

Brush

Blade Guard

Recharging Receptacle

BAB501 Detachable

Fine Tooth

Cutting Blade

I-ON / 0-OFF

Switch

LED Indicator

CA01M Outlet

Adaptor and Cord

Comb Attachment
# T1 – 1/ 8" (3 mm)

Comb Attachment
# T 2 – 1/4" (6 mm)

BAB831C IB-11_631C.indd 5-6 1/28/15 2:27 PM

LUBRICATING THE BLADE

You should lubricate the blade with BabylissPro lubricating oil provided in your kit. Turn
the trimmer to "I-ON" position and hold it so the blade is pointed downward. Spread
one drop of oil across the blade, then turn the unit to "O-OFF" position and wipe away
the excess oil with a soft cloth. After cutting wet hair, clean the blade and apply a small
drop of BabylissPro lubricating oil.

Be careful not to use too much oil and don’t oil your trimmer more than necessary,
as this could damage the motor (never attempt to oil the motor bearing, as it is
permanently lubricated). After oiling the blade, return the unit to the charging base.
Keep oil out of reach of children.

BLADE CARE

Because the blade set is precision-made for a very special use, it should always be
handled with care. Each time you finish using the trimmer, take the cleaning brush
provided and brush away any loose hair and debris. Replace the blade guard onto the
blade. Then store the unit to protect the blade until next use.

Be careful especially when changing or adjusting the blade set. When you have your
trimmer serviced, be sure that the blade set is sharpened or replaced at the same time.

REMOVAL/REPLACEMENT OF BLADE SET

To remove blade set from your trimmer, make sure that the
switch is in the "0-OFF" position and unplug trimmer from
electrical outlet. Remove the blade set by placing thumb
against the smaller cutter and pushing forward, releasing
the cutter from the trimmer housing. Replace with new
cutting system and reverse the removal procedure, only
this time place your thumb on the large cutter and snap
it into place.

HOW TO USE COMB ATTACHMENTS

1. To use the comb attachments, always turn the appliance to
"O-OFF" position.

2. Slide the comb attachment onto the front of the trimmer blade
and snap over the back of the blade.

3. To remove, push up the comb attachment at the back of the
blade and remove the comb.

4. Two comb attachments: 1/8" (3 mm) and 1/4" (6 mm) are
available for this trimmer.

Confirm the voltage (100-240 V) available at each overseas location before using this
trimmer. For connection to the Class 2 Power Supply, model CA01M outlet adaptor
(included) should be used to plug into the power socket with proper configuration.

USER MAINTENANCE INSTRUCTIONS

MAINTENANCE OF THE BLADE

Always apply oil to the blade before, during and after use. This will ensure maximum
cutting performance. Hold this trimmer away from your body in a downward position
and apply oil on the front and sides of the blade. Wipe excess oil off with a soft dry
cloth.

Any other servicing should be performed by an authorized service representative, since
this appliance has no other user serviceable parts. This product is for professional use.

VERY IMPORTANT: The blade must be cleaned and oiled
before, during and after each use with the provided
cleaning brush and lubricating oil for proper functioning.

BAB831C IB-11_631C.indd 7-8 1/28/15 2:27 PM