BaBylissPro BAB762C Operating Instructions Manual

Para su seguridad y para disfrutar

plenamente de este producto, siempre

lea las instrucciones cuidadosamente

antes de usarlo.

Afin que votre appareil vous procure en

toute sécurité beaucoup de satisfaction,

lisez toujours soigneusement les

directives avant de l’utiliser.

Operating Instructions

Model BAB762C

Outlining Trimmer with

Replaceable Brushes

For your safety and continued enjoyment of
this product, always read the instruction book
carefully before using.

Directives d'utilisation

Modèle BAB762C

Tondeuse de finition

avec balais

remplaçables

BAB762C IB-14_17A.indd 1-2 1/28/15 5:02 PM

IMPORTANT SAFETY

INSTRUCTIONS

When using electrical appliances, basic safety precautions should always be
followed, including the following:

READ ALL INSTRUCTIONS BEFORE USING

KEEP AWAY FROM WATER

DANGER –

To reduce the risk of electric shock:

1. Do not reach for an appliance that has fallen into water. Unplug

immediately.

2. Do not use appliance while bathing or in a shower.

3. Do not place or store appliance where it can fall or be pulled into a tub or
sink. Do not place in or drop into water or other liquids.

4. Always unplug this appliance from the electrical outlet immediately
after using.

5. Unplug this appliance before cleaning or putting on or taking off parts.

WARNING – To reduce the risk of burns, electric shock, fire, or injury to

persons:

1. An appliance should never be left unattended when plugged in.

2. This appliance should not be used by, on, or near children or individuals

with certain disabilities.

3. Use this appliance only for its intended use as described in this manual. Do

not use attachments not recommended by the manufacturer.

4. Never operate this appliance if it has a damaged cord or plug, if it

is not working properly, or if it has been dropped or damaged, or
dropped into water. Return the appliance to an authorized Service
Center for examination and repair.

5. Keep the cord away from heated surfaces.

6. Never operate the appliance with the air openings blocked, or while it is
on a soft surface, such as a bed or couch, where the air openings may be
blocked. Keep the air openings free of lint, hair and the like.

7. Never drop or insert any object into any opening.

8. Do not use outdoors or operate where aerosol (spray) products are being
used, or where oxygen is being administered.

9. Do not use this appliance with a damaged or broken comb or blade, as
injury may occur.

10. Always attach plug to appliance first, then to outlet. To disconnect, turn all
controls to OFF, then remove plug from outlet.

11. Do not pull, twist, or wrap line cord around appliance. Continuous

stress on cord can damage cord insulation and result in a shock
hazard.

12. Do not place appliance on any surface while it is operating.

13. Avoid skin contact with moving blades.

14. Be mindful of tangles or kinks in the cord. If the cord does become tangled
during use, turn the unit off and straighten cord before operating again.

15. Keep lubricating oil away from children. See warning on bottle.

SAVE THESE INSTRUCTIONS

BAB762C IB-14_17A.indd 3-4 1/28/15 5:02 PM

OPERATING INSTRUCTIONS

This commercial hair clipper is designed for human use only. Use on Alternating
Current 120V AC (60 hertz) only. To reduce the risk of electric shock, this
appliance has a polarized plug (one blade is wider than the other). As a safety
feature, this plug will fit in the outlet only one way. If the plug does not fit
fully in the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician to install the proper outlet. Do not attempt to defeat this safety
feature or change the plug in any way.

OILING THE BLADES

About once a month, you should oil the trimmer blades with the oil provided
in your kit. It is best to do this over a piece of newspaper. Turn the trimmer
on and hold it so that the blades are pointed downward. Spread one drop of
oil across the blades, then turn the trimmer off and wipe away the excess oil
with a soft cloth.

Be careful not to use too much oil and don’t oil your trimmer more than
necessary, as this could damage the motor. (Never attempt to oil the motor
bearing, as it is permanently lubricated). Keep oil out of reach of children.

Do not pull, twist, or wrap line cord around appliance. Continuous stress
on cord can damage cord insulation and result in shock.

Lubricating oil Cleaning brush

Blade

On/Off
switch

VERY IMPORTANT: Blades must be cleaned and oiled on a
regular basis for proper functioning. Failure to regularly
clean and oil the blades will void the warranty.

1/8" and 3/8" cutting guides

40mm high c arbon

steel T-blade

STORAGE:

when not in use, your appliance is easy to store. allow appliance to cool, then
store out of reach of children in a safe, dry location. Don not jerk or strain cord
at plug connections.

BAB762C IB-14_17A.indd 5-6 1/28/15 5:02 PM

Blade screws

Fig. 1

Blade set

Fig. 3

Comb (large blade)

Cutter (small blade)

1/32" – 1/16"

Fig. 2

Be sure that the blades are aligned properly. The teeth of the smaller blade
(cutter) should rest slightly below the upper edge of the larger blade (comb)
approximately 1/32" to 1/16" apart (see Fig. 3). If the blades are not correctly
aligned, they may cut or scratch your skin when trimming. Once the blades
have been aligned, tighten the screws firmly.

BLADE CARE

Because the trimmer blades are precision-made for a very special use, they
should always be handled with care. Each time you finish using the trimmer,
take the cleaning brush provided and brush away any loose hair that has
collected in the blades.
Be especially careful when changing or adjusting blades. When you have your
trimmer serviced, be sure that both blades are sharpened or replaced at the
same time.

To install or replace your trimmer blade set, reverse the procedure, aligning
the eccentric shaft into the moving blade bracket (see Fig. 2). With the blade
held in place, replace blade screws and tighten loosely. Turn the trimmer over
and align the blade set parallel to the trimmer’s upper housing.

HOW TO USE Cutting guides

1. To use the cutting guides, always turn the trimmer to the OFF position.

2. Slide the cutting guide onto the front of the trimmer blade and snap over
the back of the blade.

3. To remove, push up the cutting guide at the back of the blade and remove
comb.

4. Two cutting guides are available: 3 mm (1/8") and 9.5 mm (3/8").

REPLACING (REMOVING) BLADE SET

To remove the BAB762C blade set, turn the trimmer to the OFF position and
unplug it from the electrical outlet. Turn the trimmer upside down so that the
teeth of the trimmer are facing down. Place the trimmer on a flat surface
and using the screwdriver, loosen the fastening screws from the blade set.
Remove the blade set from the trimmer (see Fig. 1).

Blade

Large blade (Comb)

Blade spring

Small blade (Cutter)

Eccentric shaft

Moving blade bracket

Screw holes

Screws

BAB762C IB-14_17A.indd 7-8 1/28/15 5:02 PM