AW-CU362
Bluetooth 5.0 LE Stamp Module
Datasheet
Rev. 0.4
B
(For Standard)
1
The information contained herein is the exclusive property of AzureWave and shall not be distributed, reproduced, or disclosed
in whole or in part without prior written permission of AzureWave.
Revision
Date
Description
Initials
Approved
Version0.1
2018/03/23
Initial Version
Alex Yu
Daniel Lee
Version0.2
2018/07/11
Update:
Mechanical Information
Alex Yu
N.C. Chen
Version0.3
2018/07/12
Update:
PCB Footprint
Alex Yu
N.C. Chen
Version0.4
2018/09/16
Update:
Output Power
Receiver Sensitivity, Flash Size
Alex Yu
N.C. Chen
Revision History
The information contained herein is the exclusive property of AzureWave and shall not be distributed, reproduced, or disclosed
in whole or in part without prior written permission of AzureWave.
2
Table of Contents
Revision History .................................................................................................................................. 2
Table of Contents ................................................................................................................................ 3
1. Introduction ...................................................................................................................................... 4
1.1 Product Overview .............................................................................................................................. 4
1.2 Features .............................................................................................................................................. 5
1.2.1 Bluetooth .................................................................................................................. 5
1.3 Block Diagram .................................................................................................................................... 6
1.4 Specifications Table .......................................................................................................................... 7
1.4.1 General ..................................................................................................................... 7
1.4.2 Bluetooth .................................................................................................................. 7
1.4.3 Operating Conditions .............................................................................................. 8
2. Pin Definition ................................................................................................................................... 9
2.1 Pin Map ............................................................................................................................................... 9
2.2 Pin Table ........................................................................................................................................... 10
2.2.1 Power ...................................................................................................................... 10
2.2.2 Reset and SWD ...................................................................................................... 10
2.2.3 GPIO ........................................................................................................................ 10
2.2.4 GND PINS ............................................................................................................... 11
3. Electrical Characteristics ............................................................................................................. 12
3.1 Absolute Maximum Ratings ........................................................................................................... 12
3.2 Recommended Operating Conditions .......................................................................................... 12
3.3 Digital IO Pin DC Characteristics .................................................................................................. 12
3.4 Power up Timing Sequence .......................................................................................................... 12
3.5 Power Consumption* ....................................................................................................................... 13
3.5.1 Bluetooth ................................................................................................................ 13
4. Mechanical Information ................................................................................................................ 14
4.1 Mechanical Drawing ........................................................................................................................ 14
4.2 PCB Footprint................................................................................................................................... 15
5. Packaging Information ................................................................................................................. 16
3
The information contained herein is the exclusive property of AzureWave and shall not be distributed, reproduced, or disclosed
in whole or in part without prior written permission of AzureWave.
1. Introduction
1.1 Product Overview
AzureWave presents AW-CU362 the advanced Stamp Bluetooth 5.0 module provides a highly cost-
effective, flexible and easy to-use hardware/software device to build a new generation of connected, smart
devices. These smart-connected devices enable device to deliver a broad-range of services to consumers
including energy-management, demand-response, home automation and remote access. This allows a user
to manage comfort and convenience, also run diagnostics and receive alerts and notifications, in addition to
managing and controlling the device. Developers can leverage the rich connectivity features of these new
smart devices to create a new generation of innovative new applications and services
The device builds upon the success of Dialog’s Bluetooth microcontroller device using the Dialog DA14585
and software. Adding new enhancements and capabilities.
The AW-CU362 is powered by production quality, field-tested Dialog software that includes a rich set of
software components that work together to support the development of Smart devices, and enable these
devices to connect to mobile clients such as smart-phones, Internet-based Cloud and Smart-Grid services.
The feature-rich software stack enables OEMs to focus on application-specific software functionality, thus
enabling rapid development and reduced software development costs and risks.
4
The information contained herein is the exclusive property of AzureWave and shall not be distributed, reproduced, or disclosed
in whole or in part without prior written permission of AzureWave.
1.2 Features
1.2.1 Bluetooth
• DA14585 (Dialog DA14585 is a Bluetooth Low Energy 5.0 SoC)
• Processor
• ARM Cortex-M0, 32bit, 16MHz
• Dedicated Link Layer Processor
• AES-128 bit encryption Processor
• Memory
• 64 KB OTP Memory
• 128 KB ROM
• 96 KB Retention SRAM
• External Flash
• 1M Bit SPI flash
• Wireless
• Bluetooth V5.0
• Antenna
• Embedded Antenna
• IO Interfaces
• UART
• SWD
• GPIO
• SPI
• I2C
• ADC
• Power input
• Single 3.3V Power Input
• Package
• Stamp Module – 19.6 mm x 15 mm x 2.45 mm
• Certifications
• TBD
5
The information contained herein is the exclusive property of AzureWave and shall not be distributed, reproduced, or disclosed
in whole or in part without prior written permission of AzureWave.
1.3 Block Diagram
Block Diagram of AW-CU362
6
The information contained herein is the exclusive property of AzureWave and shall not be distributed, reproduced, or disclosed
in whole or in part without prior written permission of AzureWave.
Features
Description
Product Description
AW-CU362 Bluetooth 5.0 Stamp Module
Major Chipset
Dialog DA14585
Host Interface
UART
Dimension
19.6 mm x 15 mm x 2.45 mm
Package
30-pin
Antenna
Embedded Antenna
Weight
TBD
Features
Description
Bluetooth Standard
Bluetooth V5.0 complaint
Frequency Rage
2402~2480MHz
Modulation
GFSK (1Mbps) for Bluetooth
Output Power
(Board Level Limit)
*
0±2 dBm
Receiver Sensitivity
-92 dBm (typical)
Data Rate
Bluetooth V5.0 Only
1.4 Specifications Table
1.4.1 General
1.4.2 Bluetooth
The information contained herein is the exclusive property of AzureWave and shall not be distributed, reproduced, or disclosed
in whole or in part without prior written permission of AzureWave.
7
Features
Description
Operating Conditions
Voltage
3.3V +/- 8%
Operating Temperature
-30 ~ 85℃
Operating Humidity
TBD
Storage Temperature
-40 ~ 85℃
Storage Humidity
TBD
ESD Protection
Human Body Model
TBD
Changed Device Model
TBD
1.4.3 Operating Conditions
The information contained herein is the exclusive property of AzureWave and shall not be distributed, reproduced, or disclosed
in whole or in part without prior written permission of AzureWave.
8
2. Pin Definition
2.1 Pin Map
Top View
9
The information contained herein is the exclusive property of AzureWave and shall not be distributed, reproduced, or disclosed
in whole or in part without prior written permission of AzureWave.
Pin
No
Definition
Basic Description
Type
Level
15
VBAT_3V
3.3V Power input
PWR
3.3V
4
VPP
Leave VPP floating
Pin
No
Definition
Basic Description
Type
Level
24
SWDIO
JTAG Data input/output.
I/O
3.3V
25
SWCLK
JTAG clock signal input.
I/O
3.3V
17
RST
Reset signal (active high). Must be connected to GND if not used.
I
3.3V(internal pull
low 2.2k ohm)
Pin
No
Definition
Function 0
Function 1
Function 2
Function 3
Function 4
Function 5
Type
Level
3
P2_8
GPIO
UART0(CTS)
QD_CHA_X
I/O
3.3V
5
P2_9
GPIO
UART0(RTS)
QD_CHB_X
I/O
3.3V
6
P2_0
GPIO
UART2(CTS)
I/O
3.3V
7
P0_1
GPIO
ADC[1]
I/O
3.3V
8
P0_2
GPIO
ADC[2]
I/O
3.3V
9
P0_4
GPIO
UART0(TX)
I/O
3.3V
10
P0_5
GPIO
UART0(RX)
I/O
3.3V
11
P2_1
GPIO
SPI_CLK
I/O
3.3V
12
P0_7
GPIO
UART2(RTS)
I/O
3.3V
14
P2_2
GPIO
SPI_DI
I/O
3.3V
18
P2_3
GPIO
SPI_DO
QD_CHA_Y
I/O
3.3V
19
P2_4
GPIO
SPI_EN
QD_CHB_Y
I/O
3.3V
22
P1_0
GPIO
UART2(TX)
QD_CHA_Z
I/O
3.3V
23
P1_1
GPIO
UART2RTX)
QD_CHB_Z
I/O
3.3V
28
P2_5
GPIO
SDA
I/O
3.3V
29
P2_6
GPIO
SCL
I/O
3.3V
2.2 Pin Table
2.2.1 Power
2.2.2 Reset and SWD
2.2.3 GPIO
The information contained herein is the exclusive property of AzureWave and shall not be distributed, reproduced, or disclosed
in whole or in part without prior written permission of AzureWave.
10
Pin
No
Definition
Basic Description
Type
Level
1
GND
2
13
16
20
21
26
27
30
2.2.4 GND
11
The information contained herein is the exclusive property of AzureWave and shall not be distributed, reproduced, or disclosed
in whole or in part without prior written permission of AzureWave.
Symbol
Parameter
Minimum
Typical
Maximum
Unit
VBAT_3V
3.3V power supply
3.3
3.6
V
Symbol
Parameter
Minimum
Typical
Maximum
Unit
VBAT_3V
3.3V power supply
3.0
3.3
3.6
V
Symbol
Parameter
Minimum
Typical
Maximum
Unit
VIH
Input High Voltage
0.84
V
VIL
Input Low Voltage
0.36
V
3. Electrical Characteristics
3.1 Absolute Maximum Ratings
3.2 Recommended Operating Conditions
3.3 Digital IO Pin DC Characteristics
3.4 Power up Timing Sequence
The information contained herein is the exclusive property of AzureWave and shall not be distributed, reproduced, or disclosed
in whole or in part without prior written permission of AzureWave.
12
Item
VBAT=3.3V
Band
(GHz)
Mode
BW
(MHz)
RF Power
(dBm)
Transmit
Receive
Max.
Avg.
DUTY
%
Max.
Avg.
3.5 Power Consumption
*
3.5.1 Bluetooth
* The power consumption is based on Azurewave test environment, these data for reference only.
The information contained herein is the exclusive property of AzureWave and shall not be distributed, reproduced, or disclosed
in whole or in part without prior written permission of AzureWave.
13
4. Mechanical Information
4.1 Mechanical Drawing
14
The information contained herein is the exclusive property of AzureWave and shall not be distributed, reproduced, or disclosed
in whole or in part without prior written permission of AzureWave.
4.2 PCB Footprint
AW-CU362 TOP View PCB Layout Footprint
TOP VIEW
15
The information contained herein is the exclusive property of AzureWave and shall not be distributed, reproduced, or disclosed
in whole or in part without prior written permission of AzureWave.
5. Packaging Information
TBD
16
The information contained herein is the exclusive property of AzureWave and shall not be distributed, reproduced, or disclosed
in whole or in part without prior written permission of AzureWave.
[ FCC statement]
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/ TV technician for help.
--------------------------------------------------------------------------------------------------------------------------------------
-----------------------This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
--------------------------------------------------------------------------------------------------------------------------------------
------------------------
CAUTION:
Any changes or modifications not expressly approved by the grantee of this device could void the user's authority
to operate the equipment.
--------------------------------------------------------------------------------------------------------------------------------------
------------------------
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
--------------------------------------------------------------------------------------------------------------------------------------
------------------------
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be installed such that 20cm
may be maintained between the antenna and users.
The final end product must be labeled in a visible area with the following: "Contains FCC ID: XYZMODEL ”
and "Contains IC: XXXXX-YYYYYYY“
Information for the OEMs and Integrators
The following statement must be included with all versions of this document supplied to an
OEM or integrator, but should not be distributed to the end user.
1) This device is intended for OEM integrators only.
2) Please see the full Grant of Equipment document for other restrictions.
--------------------------------------------------------------------------------------------------------------------------------------
------------------------
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator & your
body.
-------------------------------------------------------------------------------------------------------------------------------------
17
The information contained herein is the exclusive property of AzureWave and shall not be distributed, reproduced, or disclosed
in whole or in part without prior written permission of AzureWave.
Loading...