Aztech ADSL PCI Modem Easy Start
Easy Start
(
Read Me First)
Version 1.0
Protocols Discussed:
RFC 2684 (RFC 1483)
RFC 2225 (RFC 1577)
RFC 2364
Windows® 95 OSR2.1, 98, 98 Second Edition, Me, 2000 and Windows NT® 4.0 supported
ADSL PCI Modem
Contents
About this Easy Start2
Minimum System Requirements2
Step 1: Installing Your ADSL PCI Modem3
Step 2: Connecting Your ADSL PCI Modem4
Step 3: Installing Your ADSL PCI Modem Driver
(One-Click Installation)5
Step 4: Configuring VPI/VCI Values for Internet
Connection16
Step 5: Establishing Your Internet Connection
(For RFC 2364 only)18
2
Modem Card Easy Start
About this
Easy Start
This booklet contains information on setting up your ADSL
PCI Modem. It touches on the key installation procedures
and allows you to setup your modem within minutes!
Product warranty does not apply to damage caused by lightning, power surges or wrong voltage usage.
Minimum System Requirements
• IBM PC-based computer with Pentium
®
MMX 233 processor or equivalent
• 1 CD-ROM drive
• 1 free PCI-Bus slot
• 32MB RAM
• 30MB free hard disk space for system files and modem driver
(Windows CD-ROM may be required during installation, depending on your system's
configurations.)
• Windows
®
95 OSR2.1
Windows® 98
Windows® 98 Second Edition
Windows® Me
Windows® 2000 or
Windows NT® 4.0
Please read the ReadMe.txt file on the Installation CD for any new updates
on the product.
For users who have not installed a modem card before, it is recommended that
you refer to the User Manual on the Installation CD for detailed installation
instructions. It also contains the sections on Frequently Asked Questions and
Troubleshooting Guide.
(Print out the entire User Manual for your easy reference.)
3
Modem Card Easy Start
Step 1: Installing Your ADSL PCI Modem
After removing the cover of your computer, locate any available PCI-Bus slot and
remove its cover plate.
Ê Insert your modem card firmly into the PCI-Bus slot.
Ë Secure the modem card with the mounting screw and replace the cover of
your computer.
Ê
Mounting Screw
Modem Card
Cover
Plate
PCI-bus Slot
Ë
Power off your computer and any connected devices before connecting
your modem card!
4
Modem Card Easy Start
Step 2: Connecting Your ADSL PCI Modem
Connect your card as illustrated above. Upon completion, please proceed with the
following section to install the card driver.
1. The connection for the Telephone set is optional. The Phone jack
provides convenience to users who need to use the phone when
accessing the computer.
2. No external Micro-Filter is required as your ADSL PCI Modem has a
built-in Micro-Filter at the Phone jack.
Telephone set
Telephone
Wall Socket
Telephone
extension cord
(ADSL Line)
PHONE jack - from Telephone Set
LINE jack - to Telephone Wall Socket
ADSL PCI Modem
Link LED
Data LED
Ë
Ê
5
Modem Card Easy Start
Step 3: Installing Your ADSL PCI Modem
Driver
(One-Click Installation)
This section contains the installation procedures for protocols:
- RFC 2684 (also known as RFC 1483)
- RFC 2225 (also known as RFC 1577) and
- RFC 2364
You only need to install one of the protocols as determined by your Internet Service
Provider.
The modem driver installation comes with both One-Click Installation* and Manual
Installation instructions. One-Click installation allows you to automate installation
in just a few steps whereas Manual Installation requires you to manually step
through the entire installation process.
This guide contains only the One-Click Installation* instructions. For Manual
installation, please refer to the User Manual - Installing Your ADSL PCI Modem
Driver (Manual Installation).
* One-Click Installation is not supported in Windows NT® 4.0. Please refer to the user
manual found on the Installation CD for Windows NT
®
4.0 Manual Installation.
1. The screen shots, screens information and steps illustrated in this
booklet serve only as a guide. The exact information and steps you
see on your system may vary, depending on your system's
configurations. For any dissimilarities, follow closely to the
instructions as prompted on your PC screen.
2. System may prompt for your Windows CD-ROM during the driver
installation. Have it ready by your side.
3. For Windows NT
®
4.0 users, One-Click Installation is not supported.
Please refer to the User Manual (on the Installation CD) for your
driver installation instructions.
6
Modem Card Easy Start
3.1 One-Click Installation - For Windows® 95 OSR2.1
i) Power on your computer to start Windows. It will detect your newly-installed
ADSL PCI Modem and prompt for its driver. Click Cancel.
For RFC 2364 users:
You need to have Microsoft Dial-Up Networking (DUN) version 1.3 and
above, installed in your system. If you already have
it installed in your system,
please proceed with the next step.
If not,
please carry out the following steps to install the utility before proceeding
with the next step.
a) Go to Microsoft’s website:
http://www.microsoft.com.
b) In the Microsoft Search path, enter Msdun13.exe. From the results
listed, locate and select MSDUN13.EXE: Dial-Up Networking 1.3
Upgrade.
c) Click Msdun13.exe to download the file to your harddisk.
[file size is about 2.4MBytes]
d) From your Windows taskbar , click Start > Run.... Browse to the directory
where you have downloaded Msdun13.exe. Select the file and click OK.
Loading...