Page 1
200UPR RECEIVER
200ULT • 200ULH • 200ULX SYSTEMS
User’s Guide
200UPR • 10BT • 10HT • 51XT
ON-CAMERA
UHF WIRELESS MICROPHONE SYSTEM
Azden Corporation, 147 New Hyde Park Road, P.O. Box 10, Franklin Square, NY 11010
vox - 516.328.7500 • fax - 516.328.7506 • email - azdenus@azdencorp.com
© 2005 Azden Corporation
P1050-01
Printed in USA
Specifications
Due to constant improvements, specifications are subject to change without notice.
200UPR Receiver
Frequency Range UHF 63-Channel Selectable (793.750 – 805.875MHz)
Type of Reception 2 Channel Receiver
Oscillator PLL Synthesized
RF Squelch Level 13dBµV
Frequency Response 50Hz – 15kHz
S/N Ratio >70dB “A” Weighted
A
udio Distortion <1% @ 1kHz
Operating Temp. 0°C – 45°C (32°F – 113°F)
MIC Out -64dBm @ 600 Ω - 3.5mm Mini-Jack
Power Requirement 6 – 1.5V “AA” Alkaline Batteries or 12VDC @ 200mA - 6 – 8 Hours
Dimensions 105W x 105H x 35D mm (4.13W x 4.13H x 1.38D inches)
Weight Approx. 490g Including Battery (17.28oz)
10BT Transmitter
Frequency Range UHF 63-Channel Selectable (793.750 – 805.875MHz)
Oscillator PLL Synthesized
RF Power 10mW (30mW Max.)
Frequency Response 50Hz – 15kHz
Max. Deviation ±75kHz @ 1kHz Modulation, MIC Input –11dBm
S/N Ratio >70dB “A” Weighted
A
udio Distortion <1% @ 1kHz
MIC Sensitivity ±40kHz @ -22dBm MIC Input (0dBm+0.775V) - 3.5mm Mini Jack
Operating Temp. 0°C – 50°C (32°F – 122°F)
Power Requirement 1 – 9V Alkaline Battery - 6 – 8 Hour
Dimensions 62W x 100H x 22D mm (2.44W x 3.94H x 0.87D inches)
Weight Approx. 120g Including Battery (4.23oz)
10HT Transmitter
Frequency Range UHF 63-Channel Selectable (793.750 – 805.875MHz)
Oscillator PLL Synthesized
RF Power 10mW (30mW Max.)
Frequency Response 50Hz – 12kHz
Max. Deviation ±75kHz @ 1kHz Modulation, MIC Input –11dBm
S/N Ratio >70dB “A” Weighted
A
udio Distortion <1% @ 1kHz
MIC Element ECM
MIC Sensitivity ±5kHz @ -46dBm (0dBm+0.775 V)
Operating Temp. 0°C – 50°C (32°F – 122°F)
Power Requirement 2 – 1.5V “AA” Alkaline Batteries – 8-10 Hours
Dimensions 230H x Ø 44D mm (9.05H x 1.73D inches)
Weight Approx. 130g Including Batteries (4.58oz)
51XT Transmitter
Frequency Range UHF 63-Channel Selectable (793.750 – 805.875MHz)
A
ntenna Internal Antenna
Pre-emphasis 50 ms
MAX Input Level -7dBm
Microphone Unit Dynamic Microphones
RF Output Power 15mW (50mW MAX)
Input Impedance 6K
A
udio Adj Range -63dBm ~ -18d Bm
Battery 1-9V – 6-8 Hours
Dimensions 40 x 40 x 99(L) mm (1.57 x 1.57 x3.9 inches)
Weight 152g without battery (5.4oz)
Page 2
1
2
3
14
4
15
11
12
13
10
5
UHF FREQUENCY CHART
C H A N N E L
GRP0123456 7 8
0 794.500 795.750 797.750 798.000 799.500 800.500 802.375 804.7850 805.875
1 794.375 795.625 797.625 797.875 799.375 800.375 802.250 804.625 805.750
2 793.750 795.000 797.000 797.250 798.750 799.750 801.625 804.000 805.125
3 794.250 795.500 797.500 797.750 799.250 800.250 802.125 804.500 805.625
4 794.125 795.375 797.375 797.625 799.250 800.125 802.000 804.375 805.500
5 794.000 795.250 797.250 797.500 799.000 800.000 801.875 804.250 805.375
6 793.875 795.125 797.125 797.375 798.875 799.875 801.750 804.125 805.250
Important information
Licensing of this, or any Azden wireless equipment is the user’s responsibility. The ability to receive a license
depends largely on the user’s classification, application and frequency. Contact the appropriate agency (FCC in
the US) for further information.
These devices comply with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) These devices may not cause harmful interference, and (2) These devices must accept any interference
received, including interference that may cause undesired operation.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user's authority to operate the equipment.
This devices and their antenna(s) must not be co-located or operated in conjunction with any other antenna
or transmitter.
9
5
2
1
6
1
2
2
3
4
5
+
+
-
-
3
4 4
3
7
7
88
5
3
4
4
5
6
Page 3
4 1
Thank you for purchasing Azden’s 200UPR or 200ULT/ULH/ULX wireless system,
which consists of the 200UPR receiver, 10BT transmitter and EX-503 lapel
microphone, the 10HT transmitter or the 51XT Plug-in transmitter. This equipment
is designed primarily for video cameras but is usable with most electronic
components having a microphone level input. The 200UPR allows you to “receive”
audio from two different transmitters simultaneously.
RECEIVER (200UPR)
(1-2) Power:
Remove the battery compartment lid (1) and insert six fresh Alkaline “AA” batteries
into the compartment. Make sure the battery polarity is correct as marked inside
the battery compartment. The receiver can also be powered by an external 12VDC
supply that provides 200mA (2). Follow the markings on the receiver for proper
polarity.
(3-4) Frequency select (one “set” for each channel):
With the frequency group dial on the left (3) you can select any of seven frequency
groups (numbered from 0-6). With the frequency channel dial on the right (4) you
can select any of nine frequency channels (numbered 0-8).
(5) Power (one switch for each channel)
Switches the receiver “On” or “Off”.
(6) Mic Out jack
The 200UPR is supplied with both a mini-to-mini (3-conductor-to-3-conductor)
cable and a mini-to-dual XLR cable. Which cable you use depends on the input
connector(s) on your camera.
(7) LED indicator (one for each channel)
The LED turns red when the receiver is switched “On” and green when receiving
a signal from the transmitter.
(8) Antennas
Attach both BNC connector antennas by pressing down and rotating clockwise.
The antennas can be adjusted so that they are vertical when in use.
200UPR Receiver
Mount the receiver to your camera using either the supplied hot-shoe mount (9).
Connect the appropriate output cable to the receiver and to the microphone
input(s) on your video camera. Switch one or both channels of the 200UPR to
“ON” and the LED(s) should turn red. If either does not light, check the battery.
When the 200UPR receives a signal the LED for that channel will turn green.
10BT Bodypack Transmitter
Plug in the supplied lapel microphone and clip it to your subject. The microphone
should be placed 4-12 inches from your subject’s mouth. Clip the transmitter to
a belt using the supplied belt-clip (15) or place it in a pocket. Switch the transmitter
Power and Audio to “ON”. The LED should light green. If it does not, check the
battery. Have someone speak into the microphone as you monitor the sound
through thecamera’s monitor output. If the sound is distorted lower the input gain
on the transmitter. If there is not enough volume raise the input gain on the
transmitter.
10HT Handheld Transmitter
Switch the transmitter to “ON”. The LED should light green. If it does not, check
the batteries. If it glows red it is time to replace the batteries. Have someone
speak into the microphone as you monitor the sound through the camera’s monitor
output. If the sound is distorted lower the gain on the transmitter. If there is not
enough volume raise the gain on the transmitter.
51XT Plug-In Transmitter
Switch the transmitter to “ON”. The LED should light green. If it does not, check
the battery. Have someone speak into the microphone as you monitor the sound
through the camera’s monitor output. If the sound is distorted lower the gain on
the transmitter. If there is not enough volume raise the gain on the transmitter.
Page 4
2 3
Operating the system
Because this is a frequency agile system, you have to choose the frequency for both the transmitter and
receiver via the group and channel dials (3 and 4). We cannot stress enough that the transmitter and
receiver pair MUST BE SET TO THE SAME GROUP and CHANNEL NUMBER. Additionally,
multiple systems used in the same location should be on the same group number but on different channel
numbers. (See below for example) ALWAYS CHECK THAT THE FREQUENCY YOU’VE CHOSEN
IS CLEAR PRIOR TO USING THE SYSTEM.
Finally, if you need to change the group or channel number you must shut off both the transmitter and
receiver before making a change. When the units are turned “On” the frequency is locked and will not
change.
When operating multiple systems all receivers and transmitters must be on the same group.
Example: 4 systems operating simultaneously.
To change the frequency of a transmitter/receiver pair that is already on YOU MUST TURN
BOTH THE TRANSMITTER AND RECEIVER “
OFF” FIRST!
System #1
Group Channel
System #2
Group Channel
System #3
Group Channel
System #4
Group Channel
Receivers
2 4 25 26 27
Transmitters
2 4 25 26 27
(3) Frequency select
The group knob allows you to select any of
seven frequency groups (numbered from 0-
6). The channel knob allows you to select
any of nine frequency channels (numbered
from 0-8) within the selected group.
(4) Power and Audio switches
The power “On/Off” switch enables and
disables all transmitter functions while the
Audio “On/Off” switch turns just the
transmitter’s Audio signal on and off.
Switching the Audio to “Off” will cause the
receiver to mute using the tone squelch
circuitry in the receiver. This allows the
microphone to be handled with no noise. The
“Phantom” switch allows the 51XT to provide 5V to power electret condenser microphones.
(5) Audio input LEVEL control
This enables you to adjust the input level of the microphone. Turn clockwise to increase, or
counterclockwise to decrease the input level. A small screwdriver is supplied to make adjustments.
(6) LED INDICATORS
The POWER LED turns green when power is turned “On” or red if battery level is low. If this
LED lights up red replace the battery.
The AF PEAK LED lights up if the input level is set to high,
indicating the onset of distortion. Lower the input level so that
the AF PEAK LED lights only occasionally.
To plug the 51XT onto a microphone (low impedance with XRL
connector) first make certain the locking-ring is turned fully up
(rotate counterclockwise). Then plug the 51XT fully into the microphones XLR connector and tighten by
rotating the ring fully down (clockwise).
BODYPACK TRANSMITTER (10BT)
(1) Remove the battery compartment lid by sliding it down. Insert one fresh alkaline 9V battery (2) into the
compartment. Make sure the battery polarity is correct as marked inside the battery compartment.
In addition to the battery, inside the battery compartment you will find the following:
(3-4) Frequency select
With the frequency group dial on the left (3) you can select any of seven frequency groups (numbered
from 0-6). With the frequency channel dial on the right (4) you can select any of nine frequency channels
(numbered 0-8).
(10 and 12) Power and Standby switches
The power “ON” and “OFF” switch (10) enables and disables all transmitter functions while the Audio
switch (12) “ON” and “Standby” positions turn the audio off and on. Switching the transmitter to
“Standby” will cause the receiver to mute. This allows the microphone to be handled with no noise.
(11) The LED Indicator turns green when the Power is turned “ON”. This LED will also turn red to indicate
that battery level is low and the battery must be changed.
(13) The MIC jack accepts a 3.5mm jack from a microphone such as the supplied EX-503. Other lavalier
and/or headset microphones can also be used.
(14) The Audio input Level Control enables you to adjust the input level of the microphone. Turn clockwise
to increase, or counterclockwise to decrease the input level. A small screwdriver is supplied to make
these adjustments. The level control is factory-preset in the center position.
HANDHELD TRANSMITTER (10HT)
(1) Remove the battery compartment cover by rotating it counterclockwise and sliding it down.
(2) Insert one fresh alkaline 1.5 V battery into each side of the battery compartment. Make sure the
battery polarity is correct as marked inside the battery compartment.
(3) Power Switch and LED
The power “ON” and “OFF” switch (3) enables and disables all transmitterfunctions. Sliding it toward the
LED turns the transmitter ON. The LED will turn green when the batteries are fresh and red when it is time
to replace the batteries. Sliding the switch away from the LED turns the transmitter OFF.
In addition to the batteries, inside the battery compartment you will find the following:
(4) Frequency select
With the frequency group dial on the left you can select any of seven frequency groups (numbered from
0-6). With the frequency channel dial on the right you can select any of nine frequency channels
(numbered 0-8).
(5) The Audio Level Control enables you to adjust the overall level of the microphone. Turn clockwise to
increase, or counterclockwise to decrease the volume level. A small screwdriver is supplied to make
these adjustments. The level control is factory-preset in the center position.
51XT plug-in XLR transmitter
(1) Open the battery compartment lid by sliding it down and raising it
(2) Insert one fresh alkaline 9-volt battery into the compartment. Make sure battery polarity is correct.
Loading...