Ayrton wildsun k25 User Manual

Download

Page 1

USER MANUAL V.1

ENGLISH VERSION 04 28 2016

Page 2

Page 3

USER MANUAL _ 3

SUMMARY

Introduction Safety instructions Conditions of use Presentation and features Dimensions Description Installation instructions Installation method using truss hooks DMX512 connection DMX512 connection with termintion plug The WILDSUN K25 DMX address setting Control Panel WILDSUN K25 control panel menu - Option details Master/Slave Mode settings Led mapping DMX Chart Error Messages Care and maintenance Technical Speciﬁcations Warranty

4 4 4 5 6 6 7 7 7 8 8 8 9 12 13 14 15 15 15 16

Page 4

USER MANUAL _ 4

INTRODUCTION

Thank you for selecting the AYRTON WILDSUN K25 luminaire.

WARNING !

This product is not suitable for household use.

You now own a professional lighting unit that offers endless possibilities. Before installing, make sure that no damage was done to your luminaire during transport. If this is the case, do not use the product and immediately contact your authorized AYRTON dealer.

For your own safety and that of others, please read this instruction manual carefully before installing the unit.

Anyone involved in installing, operating or servicing the WILDSUN K25 must:

• Be a qualiﬁed, authorized professional

• Strictly follow the instructions in this user manual.

Please take the time to read this manual carefully and thoroughly before installing and operating the luminaire. You should have a good knowledge of its operating conditions and all pertinent product information.

After you have become familiar with this manual, we recommend that you keep a copy for future use. All the information found in this manual is subject to change without notice. AYRTON reserves the right to modify and upgrade its range of products, with no obligation to integrate these changes into products already sold.

SAFETY INSTRUCTIONS

Please read the safety instructions and warnings in this manual carefully before installing and operating the WILDSUN K25.

WARNING!

Risk of electric shock. Use caution when handling. This luminaire requires high voltage, which can result in electric shock.

The WILDSUN K25 left our factory in perfect working condition. However, if you notice a defect, immediately contact your authorized AYRTON dealer before use. The manufacturer cannot be held responsible for damages caused by a failure to follow the safety, installation or assembly instructions contained herein, or by any modiﬁcation made to the luminaire.

Failure to observe the safety, installation or assembly instructions contained herein, or any modiﬁcation made to the WILDSUN K25 luminaire will render the warranty null and void.

Check that the supply voltage does not exceed the maximum authorized limit. Check that your electrical installation complies with current standards.

In all cases, make sure that the power cables attached to your WILDSUN K25 have not been damaged due to cuts and splices or crushed in any way. Handle these cables with extreme caution while they are connected to a power source.

Your WILDSUN K25 conforms to Class 1 safety standards. The unit must be grounded electrically. Make sure that the power source connected to your WILDSUN K25 is switched off before attempting any work on it.

Installation and connection to an electrical source must be performed by an authorized installer. AYRTON declines all responsibility should this luminaire be installed by an unqualiﬁed person.

Never disconnect your WILDSUN K25 by pulling on the power cable! First unlock the connector lock ring on the power cable until it is fully disengaged, and then gently pull on the connector to disconnect the cable.

Do not connect or disconnect the power cable of your WILDSUN K25 with wet hands.

At ﬁrst use, your WILDSUN K25 may give off an odor. This is a normal occurrence that should dissipate after a few minutes of operation.

WARNING!

Do not connect or disconnect the power cable at your WILDSUN K25 if the cable is energized! This could cause arcing and damage your WILDSUN K25, requiring repair.

Be careful to power off your COSMOPIX-R by removing the power plug from the source, before connecting or disconnecting the luminaire.

WARNING!

This unit contains Class 2 LED emitters (EN60625-1): 1994)

This luminaire uses multiple high-power (Class 2) LED-type (Light Emitting Diode) lamps. Never look directly into the lamps if lit or stand directly in line with the luminaire if close by.

Installation, removal or replacement of the unit must be performed with power off to prevent any risk of glare and eye injury.

WARNING!

The ﬁxture quickly becomes very hot during operation.

To avoid risk of burn, never handle or adjust the luminaire while it is energized and after it has been lit for more than 10 consecutive minutes. Some parts of the luminaire can reach a high temperature, particularly the body/radiator. Turn off the luminaire and wait for it to cool before handling.

CONDITIONS OF USE

Your WILDSUN K25 is a moving-head luminaire equipped with multiple LEDs intended for professional use (e.g., architectural, stage, television, theater, or museum lighting).

The WILDSUN K25 luminaire has an IP20 protection rating. It is intended strictly for indoor use. It must never be partially or fully submerged, even temporarily.

Page 5

USER MANUAL _ 5

Condensation may form on your WILDSUN K25 in the following cases:

• Immediately after turning on the heating

• In places with fog or a high level of humidity

• When the luminaire is suddenly moved from a cold to a warm environment, or vice versa.

In such cases, you must wait until the luminaire readjusts to the ambient temperature of the room where it will be installed for operation.

Do not shake the WILDSUN K25 while installing or handling.

Do not pull the WILDSUN K25 by one of its cables to move it. Lift the luminaire by its handles.

Choosing the appropriate place to install the WILDSUN K25 is essential. The following points should be observed:

• Do not expose it to a heat source.

• Do not install it near ﬂammable materials.

• Be sure that dust or miscellaneous debris cannot clump around the body of the luminaire as this may interfere with its optimal cooling and proper operation.

• The WILDSUN K25 must be installed out of reach of the public and all persons not authorized to operate the luminaire.

We recommend a minimum distance of 5 m between the outside surface of the light and the illuminated object.

Due to the nature of its cooling principle, you should never prevent air from circulating around the body of the luminaire. You must provide a minimum clearance around your WILDSUN K25 to allow for cooling.

The WILDSUN K25 can be installed in a ground pit or any other conﬁned enclosure only under certain conditions. With this kind of installation, a system of forced ventilation should be used up to allow air to circulate freely around the luminaire(s). The air must be constantly renewed because the luminaire cannot be operated in closed system. Failure to comply with these requirements may destroy or prematurely wear the WILDSUN K25, and AYRTON cannot be held responsible. Please consult your AYRTON dealer for more information on this type of installation.

No load should be placed on the WILDSUN K25. The ﬁxture must not be installed in such a way as to allow a person, vehicle or any object to run over or park on it.

Never lay or drop any hard, heavy, or blunt, objects on the WILDSUN K25. This includes items made of glass or porcelain (e.g., bottles, dishware, or glass beads). The luminaire is made of materials such as plastic and extruded aluminum, making it resistant but not unbreakable. Objects made of hard materials such as steel or glass that fall on the unit may cause breakage of the plastic parts or the body. AYRTON cannot be held responsible for the luminaire’s broken plastic parts or body, which are not covered under warranty.

The temperature of the room where the WILDSUN K25 is installed must never exceed 45°C (Ta = 45°C).

The WILDSUN K25 luminaire requires a 207-240 VAC supply voltage. Check that your luminaires have been installed for an application that is compatible with this information.

Check that the brackets on which you hang or attach your WILDSUN K25 can sustain the weight of the luminaire (38 kg), taking into consideration

all necessary safety factors.

Do not use your WILDSUN K25 before being familiar with these recommendations and do not allow unqualiﬁed personnel to handle the product.

To transport your WILDSUN K25, we strongly recommend that you use the complete original packaging, including the dense protective foam inserts.

If your WILDSUN K25 is not being used for a long period, you should disconnect the luminaire from the power source.

Never dispose of the WILDSUN K25 in a rubbish bin. Ensure that it is recycled. Please consult the current legislation in your country on recycling electronic equipment.

PRESENTATION AND FEATURES

WILDSUN K25 is a non-waterproof moving head wash light (IP20 protection rating) using the latest generation of high-performance of LED-type lamps.

This luminaire can be controlled remotely by an external DMX512 signal.

The WILDSUN K25 incorporates high power white LEDs.

The WILDSUN K25 has a total of 217 LEDs that can be controlled by height independent zones. The luminaire requires from 11 to 21 DMX channels to be controlled via an external command system that sends a DMX512 signal (see below for details).

To adjust the settings on the WILDSUN K25 (i.e., DMX address, DMX operating mode and other options), a Remote Device Management (RDM)-type DMX controller may be required. The DMX RDM protocol is a universal, widely used standard.

There are a multitude of RDM DMX controllers on the market from different manufacturers (excluding AYRTON). It is worth noting that an RDM DMX controller is not required to change the settings on the WILDSUN K25. A light console or any standard DMX-type controller is sufﬁcient.

The WILDSUN K25 consists of a metal frame and plastic covers. The power connectors and DMX512 signal connectors are on the back of the ﬁxture’s base.

Page 6

USER MANUAL _ 6

DIMENSIONS

Bottom view

539

107

Front view

348

415

123

440

696

544

Side view

348

136

213

476

DESCRIPTION

2 3 4 5 6 7 89

12 13 14 15 16

1. LED Assembly

2. Display

3. Left button

4. Mode/Esc button

5. Down button

6. Enter button

7. Right button

8. Up button

9. Handle

10. Antenna – Wireless DMX

11. 5-Pin DMX Out

12. 5-Pin DMX In

13. RJ45 Out

14. RJ45 In

15. Fuse

16. Power In

Page 7

USER MANUAL _ 7

INSTALLATION INSTRUCTIONS

During installation please observe the instructions according to GB7000.15 / EN60598-2-17 standards and other national standards applicable. This luminaire should be installed by a qualiﬁed technician.

The ﬁxture should be used in an environment with a temperature between

-5°C and +45°C. Do not operate the luminaire outside this temperature range.

The luminaire must be hung so that the weight of this unit multiplied by 10 can be sustained for 1 hour without causing the suspension system or the supporting structure to be deformed.

The installation must always be secured at a second attach point, e.g., by a safety cable of the appropriate size. Do not stand under the luminaire while it is being installed, dismantled or serviced.

The operator must ensure that a qualiﬁed technician has approved the installation of the luminaire for safety before it is ﬁrst operated.

Installation should be inspected once a year by a qualiﬁed technician.

WARNING!

The installation of this luminaire must be validated by a qualiﬁed technician before it is used for the ﬁrst time.

The luminaire should be installed in a location where the public cannot, touch, walk or sit on the luminaire. Suspending the luminaire and/or installing it high up requires considerable experience, e.g., calculating load, selecting and adapting quality fastening materials, and periodically inspecting the entire installation. Without this skill and knowledge, do not attempt to install this unit by yourself. Improper installation may cause an accident resulting in personal injury or death.

WARNING!

The luminaire should be connected to an electrical source by a qualiﬁed electrician.

Before installing the luminaire make sure that the selected installation spot can support at least 10 times the weight of the unit. Connect the luminaire to the power source by the power cord.

INSTALLATION METHOD USING TRUSS HOOKS

Refer to the following diagram when installing the WILDSUN K25 with truss hooks using omega bracket:

• Attach the clamp to the omega bracket using an M12 screw.

• Insert the quick-lock fasteners of the ﬁrst omega bracket into the respective holes on the base of the unit. Turn the quick fasteners fully clockwise.

• Install the second omega bracket.

• Insert the safety cable through the holes at the bottom of the base and the truss or a stable attachment point. Insert the end into the hole and tighten the safety screw.

Note: The last step is very important to ensure that the luminaire does not fall.

DMX512 CONNECTION

Connect the DMX input (XLR connector) cable of the luminaire to the DMX output (female XLR connector) of your controller. You can connect multiple luminaires to this same DMX line in a daisy chain. The DMX cable must be a shielded twisted pair that is equipped with male and female XLR connectors.

Refer to the following diagram when connecting the WILDSUN K25 luminaires in a daisy chain:

Address 1 Address 22 Address 43

Page 8

USER MANUAL _ 8

DMX512 CONNECTION WITH TERMINATION PLUG

For installations where the DMX cable must extend over long distances, or if it is located near areas with major electrical disturbance, it is recommended to use a DMX termination plug. This helps prevent luminaires from malfunctioning due to interference. The DMX termination plug, composed simply of a male XLR input connector with a 120-Ohm resistor, is soldered between pins 2 and 3. This plug must be connected to the DMX output of the last luminaire in the chain.

Refer to the following diagram:

SING DMX VIA ART-NET

To control the WILDSUN K25 via ART-NET, the ﬁxtures must be interconnected with CAT5 RJ45 cable. Be careful to enter all necessary information into the ART-NET universe being used and specify in the menu that the WILDSUN K25 is being controlled through ART-NET (see OPTION DETAILS in the « OPTIONS » menu).

WARNING!

THE WILDSUN K25 CAN ONLY READ THE FIRST TWENTY FOUR UNIVERSES OF AN ART-NET PACKAGE. IF YOU HAVE MORE THAN 24 UNIVERSES IN YOUR NETWORK, YOU MUST USE A CONFIGURABLE SWITCH TO FILTER EACH RJ45 OUTPUT.

THE WILDSUN K25 DMX ADDRESS SETTING

All luminaires have a DMX start address correctly set when using a DMX signal to control them. The DMX start address is the channel from which the luminaire “listens” to the digital control information sent by the DMX controller.

The start address must conform to the one recorded on the DMX controller to run the luminaire. This address is the DMX value that appears on the luminaire’s display. You can set the same address for all the luminaires, or some of them, but you can also set a different address for each luminaire, as needed.

If you do set the same address for all the luminaires, they will all “listen” from the DMX channel you have set. The instructions sent by the DMX controller will affect all luminaires at the same time. If you set a different address per luminaire, the DMX controller can control each independently.

If, for instance, the ﬁxtures are preset in 21-channel DMX mode (required for full control), you will need to adjust the DMX address for the luminaires as follows: The ﬁrst unit with DMX address 001, the second with DMX address 022 (21 + 1), the third with DMX address 043 (21 + 22), etc.

CONTROL PANEL (MENU OPTIONS)

A large number of settings are accessible from the ﬁxture’s control panel. A good working knowledge of it will enhance the ﬁxture’s possibilities.

You can access the Main Menu by pressing the

key until the display

ﬂashes.

Cycling through the menus is performed by pressing the

, ,

keys, as required:

Press the

key to select the desired menu.

Change the selection by pressing the

, or , keys.

Conﬁrm your selection by pressing the

key.

Exit a menu at any time by pressing the

key.

Notes: You can return to the display by pressing the

or keys from the basic display. If the screen fails to respond, hold the “Mode Esc” key down for at least 3 seconds to free up the display.

The ﬁxture’s menu functions are described in the following table:

Address

Set Dmx Addr A001~AXXX DMX address setting

Mode

User Mode Stand Mode

Basic Mode Extend Mode User Mode A User Mode B User Mode C

User’s mode to change channel numbers

Edit User Max channel

PAN :

Edit DMX proﬁle

Options

Status No DMX Mode

Pan Reverse Tilt Reverse Pan Degree Feedback Pan/Tilt Spd Hibernation

Close/Hold/Auto/Music ON/OFF ON/OFF 630/540 ON/OFF Speed 1~ 4 OFF, 01min > 99min

Auto run if no DMX Pan Reverse movement Tilt Reverse movement Pan Degree Select Movement Feedback Reset Pan/Tilt Stand by Mode

Service PIN Service PIN

RDM PID Set IP

Password=XXX xxxxxx xxx.xxx.xxx.xxx

Service Password“=050” RDM PID Code IP Addr

Fans Control Auto

Stage Studio

Head Fans Speed Mode

Select

Disp.Setting Shutoff Time

Flip Display Key Lock Disp Flash

02~60m 05m ON/OFF ON/OFF ON/OFF

Display shutoff time Reverse 180 degree Key Lock No Signal Flash

Signal Select

DMX WDMX ArtNet sACN

DMX Wireless DMX Art-Net sACN

Set Universe xx Art-Net Universe NO.

Temp. C/F

Celsius Fahrenheit

Temperature switch between °C/°F

Initial Pos. PAN =XXX Initial effect position

Wireless DMX Activate WDMX

Act&Data Out Rest WDMX

Activate WDMX Activate & Data Out Reset Wireless DMX Mem

Trigger DMX Value Disp.

Set To Slave Auto Program

PAN, TILT etc. Slave1,Slave2,Slave3 Master / Alone

DMX value display Slave setting Auto program

Reset Default ON/OFF Restore factory sett.

Info

Time Info. Current Time

Ttl Life Hrs Last Run Hrs Timer PIN Clr Last Run

XXXX(Hours) XXXX(Hours) XXXX(Hours) Password=XXX ON/OFF

Temp. Info

Head Temp. XXX °C/°F

Software Ver V1.0… Software version

Network

IP,Mask,Mac Network setting

Page 9

USER MANUAL _ 9

Test

Home All

Pan&Tilt

Reset all motors Reset Pan&Tilt

Test Channel PAN …… Test function

Manual Ctrl. PAN =XXX

Fine adjustment of parameters

Calibration --Password--

PAN :

Password “050” Calbrate and adjust the effects to standard/right position

Preset

Select Prog. Prog. Part 1 = Program 1 ~ 10 Program 1

Prog. Part 2 = Program 1 ~ 10 Program 2 Prog. Part 3 = Program 1 ~ 10 Program 3

Select programs to be run

Edit Prog. Program 1

: Program 10

Program Test Step 01=SCxxx Step 64=SCxxx

Testing program Program in loop Save and exit

Edit Scenes Edit Scene 001

~ Edit Scene 250

Pan,Tilt,……

--Fade Time--

--Secne Time-Input By Outside

Save and automatically return manual scenes edit

Scenes Input XX~XX Automat. scenes rec

WILDSUN K25 CONTROL PANEL MENU – OPTION DETAILS

The following section provides details on the options that can be selected through the control panel menu. Refer to the table above.

Note: You can exit this menu at any time by pressing “Mode Esc” repeatedly until you return to the home screen.

ADDRESS

Allows you to change a DMX address from the ﬁxture’s control panel.

w Access the menu by pressing the “Mode Esc” key. w Go to the “ADDRESS” menu and press “Enter”, then ﬁnd “Set DMX

Address.”

w Use the up/down arrows to scroll through until you locate the desired

address and press “Enter” to conﬁrm.

MODE

USERS MODE

Allows you to select the DMX mode from the following: “Basic Mode” (11 DMX channels ), “Standard Mode” (14 DMX channels), “Extended Mode” (21 DMX channels), “User Mode A”, “User Mode B”, “User Mode C.”

w Access the menu by pressing the “Mode Esc” key. w Use the up/down arrow keys to reach the “MODE” menu and press

“Enter.” Then from “User Mode” choose one of the 6 modes above. Consult the “CHART DMX” table for more information on Basic, Standard and Extended Mode. “User Modes A”, “B”, or “C” are user-deﬁnable.

EDIT USER A, B, C

To customize the mode, go to “MODE” and select “Edit UserMode A, B or C” and press “Enter.” Scroll through each setting and press “Enter” to set the desired address.

OPTIONS

STATUS No DMX Mode

Deﬁnes the ﬁxture’s state when there is no command signal from the DMX

controller. The ﬁxture can either launch a program automatically, close the shutter, or even remain in the state when the last DMX values (Hold) were received. The default setting is “Hold.”

w Access the menu by pressing the “Mode Esc” key. w Use the up/down arrow keys to reach the “OPTION” menu and press

“Enter.” Then use the left/right arrow keys to select “Status.” Finally, use the left/right arrow keys to select “No DMX Mode.”

w Scroll through the different options using the left/right arrows and press

“Enter” to conﬁrm.

Pan Reverse

Reverses the PAN movement.

w Access the menu by pressing the “Mode Esc” key. w Use the up/down arrow keys to reach the “OPTION” menu and press

“Enter.” Then use the left/right arrow keys to select “Status.” Finally, use the left/right arrow keys to select “Pan Reverse.”

w Scroll through the different options using the left/right arrows and press

“Enter” to conﬁrm.

Tilt Reverse

Reverses the direction of the TILT movement.

w Access the menu by pressing the “Mode Esc” key. w Use the up/down arrow keys to reach the “OPTION” menu and press

“Enter.” Then use the left/right arrow keys to select “Status.” Finally, use the left/right arrow keys to select “Tilt Reverse.”

w Scroll through the different options using the left/right arrows and press

“Enter” to conﬁrm.

Pan Degree

Adjusts the amplitude of the PAN movement at 630° or 540°.

w Access the menu by pressing the “Mode Esc” key. w Use the up/down arrow keys to reach the “OPTION” menu and press

“Enter.” Then use the left/right arrow keys to select “Status.” Finally, use the left/right arrow keys to select “Pan Degree.”

w Scroll through the different options using the left/right arrows and press

“Enter” to conﬁrm.

Feedback

Readjusts the PAN and TILT positions automatically in the event of accidental shifting due to a physical shock.

w Access the menu by pressing the “Mode Esc” key. w Use the up/down arrow keys to reach the “OPTION” menu and press

“Enter.” Then use the left/right arrow keys to select “Status.” Finally, use the left/right arrow keys to select “Feedback.”

w Scroll through the different options using the left/right arrows and press

“Enter” to conﬁrm.

Pan/Tilt Spd

You can choose between four movement speeds, from “Speed 1” to “Speed 4.” The “Speed 1” setting is the fastest.

w Access the menu by pressing the “Mode Esc” key. w Use the up/down arrow keys to reach the “OPTION” menu and press

“Enter.” Then use the left/right arrow keys to select “Status.” Finally, use the left/right arrow keys to select “Pan/Tilt Spd.”

w Scroll through the different options using the left/right arrows and press

“Enter” to conﬁrm.

Hibernation — Standby mode

The LEDs and the pan/tilt motors will be powered down if the luminaire receives no DMX signal for several minutes (default setting is OFF). If the DMX signal is restored after this time limit, the luminaire will perform a RESET before resuming normal operation.

Page 10

USER MANUAL _ 10

w Access the menu by pressing the “Mode Esc” key. w Use the up/down arrow keys to reach the “OPTION” menu and press

“Enter.” Then use the left/right arrow keys to select “Status.” Finally, use the left/right arrow keys to select “Hibernation.”

w Scroll through the different options using the left/right arrows and press

“Enter” to conﬁrm.

SERVICE PIN

WARNING! For normal operation the “Service pin” menu information should not be changed. Contact your dealer for more information.

Service PIN

Allows you to enter a password to access the advanced options such as RDM PID, Set IP, Set Device IP, Set LED BIN and Change to bin (pwd: 50).

w Access the menu by pressing the “Mode Esc” key. w Use the up/down arrow keys to reach the “OPTION” menu and press

“Enter.” Finally, use the left/right arrow keys to select “Service Pin.”

w Scroll up to “50” using the left/right arrows and press “Enter” to conﬁrm.

RDM PID

Allows you to set the ﬁxture’s RDM PID code.

w Access the menu by pressing the “Mode Esc” key. w Use the up/down arrow keys to access the “OPTION” menu and press

“Enter.” Then use the left/right arrow keys to select “Service Pin.” Finally, use the left/right arrow keys to select “RDM PID.”

w Use the up/down arrow keys to change the value and left/right to move

from one number to the next. Press “Enter” to conﬁrm.

Set IP

Allows you to set the ﬁxture’s IP address.

w Access the menu by pressing the “Mode Esc” key. w Use the up/down arrow keys to access the “OPTION” menu and press

“Enter.” Then use the left/right arrow keys to select “Service Pin.” Finally, use the left/right arrow keys to select “set IP.”

w Use the up/down arrow keys to change the value and left/right to move

from one number to the next. Press “Enter” to conﬁrm.

FAN CONTROL FAN Control

Allows you to choose the fan speed on the ﬁxture head. The options are AUTO, STAGE or STUDIO.

w Access the menu by pressing the “Mode Esc” key. w Use the up/down arrow keys to reach the “OPTION” menu and press

“Enter.” Then use the left/right arrow keys to select “Fans Control.”

w Use the left/right arrow keys to select the fan option. Press “Enter” to

conﬁrm.

DISP.SETTING Shut off Time

Allows the ﬁxture’s LCD display to be turned off after a period of 2 to 59 minutes.

w Access the menu by pressing the “Mode Esc” key. w Use the up/down arrow keys to reach the “OPTION” menu and press

“Enter.” Then use the left/right arrow keys to select “Disp.Setting.” Finally, use the left/right arrow keys to select “Shut off Time.”

w Use the left/right arrow keys to change the value displayed. Press

“Enter” to conﬁrm.

Flip Display

Allows you to rotate the display by 180°. This can be highly useful when the ﬁxture is installed with the head facing down.

w Access the menu by pressing the “Mode Esc” key. w Use the up/down arrow keys to reach the “OPTION” menu and press

“Enter.” Then use the left/right arrow keys to select “Disp. Setting.” Finally, use the left/right arrow keys to select “Flip Display.”

w Use the left/right arrow keys to select ON or OFF. Press “Enter” to

conﬁrm.

Key Lock

Activates the automatic keypad lock. If this function is enabled, the keys will be automatically locked 15 seconds after exiting edit mode. Hold the MENU key down for 3 seconds to deactivate this function.

w “Mode Esc” key. w Use the up/down arrow keys to reach the “OPTION” menu and press

“Enter.” Then use the left/right arrow keys to select “Disp. Setting.” Finally, use the left/right arrow keys to select “Key Lock.”

w Use the left/right arrow keys to select ON or OFF. Press “Enter” to

conﬁrm.

DispFlash

Causes the display to ﬂash as a warning that there is no DMX signal.

w Access the menu by pressing the “Mode Esc” key. w Use the up/down arrow keys to reach the “OPTION” menu and press

“Enter.” Then use the left/right arrow keys to access the “Disp. Setting” submenu. Finally, use the left/right arrow keys to select “DispFlash.”

w Use the left/right arrow keys to select ON or OFF. Press “Enter” to

conﬁrm.

SIGNAL SELECT Signal Select

This menu allows you to choose what type of signal is used to control the ﬁxture (DMX, WDMX, Art-Net or sACN).

w Access the menu by pressing the “Mode Esc” key. w Use the up/down arrow keys to reach the “OPTION” menu and press

“Enter.” Then use the left/right arrow keys to select “Signal Select” submenu.

w Use the left/right arrow keys to select the signal type used. Press “Enter”

to conﬁrm.

SET UNIVERSE Set Universe

w Access the menu by pressing the “Mode Esc” key. w Use the up/down arrow keys to reach the “OPTION” menu and press

“Enter.” Then use the left/right arrow keys to select “Set Universe” submenu.

w Use the up/down arrow keys to scroll through until you locate the

desired address and press “Enter3 to conﬁrm.

TEMP. C/F

Allows you to select the unit of measurement for the temperature values, in either Celsius or Fahrenheit.

w Access the menu by pressing the “Mode Esc” key. w Use the up/down arrow keys to reach the “OPTION” menu and press

“Enter.” Then use the left/right arrow keys to access the “Temp. C/F” submenu.

w Use the left/right arrow keys to select the unit of measurement. Press

“Enter” to conﬁrm.

INITIAL POS.

Controls the initial position of the ﬁxture’s effects.

w Access the menu by pressing the “Mode Esc” key.

Page 11

USER MANUAL _ 11

w Use the up/down arrow keys to reach the “OPTION” menu and press

“Enter.” Then use the left/right arrow keys to access the “Initial Pos” submenu.

w Use the left/right arrow keys to select the desired setting, press “Enter”,

and use the left/right arrow keys to change the value. Press “Enter” to conﬁrm.

WIRELESS DMX

This menu allows you to activate, activate and resend data via XLR plug or reset wireless pairing.

w Access the menu by pressing the “Mode Esc” key. w Use the up/down arrow keys to reach the “OPTION” menu and press

“Enter.” Then use the left/right arrow keys to access the “Wireless DMX” submenu.

w Use the left/right arrow keys to activate the setting. Press “Enter” to

conﬁrm.

TRIGGER DMX Value Disp.

Allows you to view the DMX value received for each setting. The “ALL” option will display only the setting being edited.

w Access the menu by pressing the “Mode Esc” key. w Use the up/down arrow keys to reach the “OPTION” menu and press

“Enter.” Then use the left/right arrow keys to access the “Trigger” submenu. Use the right/left arrow keys to select “DMX value Disp.”

w Use the left/right arrow keys to select which setting to display. Press

“Enter” to conﬁrm.

Set To Slave

Sets the ﬁxture to SLAVE Mode for receiving instructions from a master luminaire (see Master/Save mode settings, below).

w Access the menu by pressing the “Mode Esc” key. w Use the up/down arrow keys to reach the “OPTION” menu and press

“Enter.” Then use the left/right arrow keys to access the “Trigger” submenu. Use the right/left arrow keys to select “Set To Slave.”

w Use the right/left arrow keys to deﬁne whether the ﬁxture is Slave 1,

Slave 2 or Slave 3, accordingly. Press “Enter” to conﬁrm.

Auto Program

Allows you to run an internal program (a sequence of scenes) by selecting whether the ﬁxture is operating alone or as a master.

w Access the menu by pressing the “Mode Esc” key. w Use the up/down arrow keys to reach the “OPTION” menu and press

“Enter.” Then use the left/right arrow keys to access the “Trigger” submenu. Use the right/left arrow keys to select “Auto Program.”

w Use the right/left arrow keys to select whether the ﬁxture is “Alone” or

“Master.” Press “Enter” to conﬁrm.

Note: See “AUTO” menu to create internal programs.

RESETDEFAULT

Restores the factory default settings on the ﬁxture.

w Access the menu by pressing the “Mode Esc” key. w Use the up/down arrow keys to reach the “OPTION” menu and press

“Enter.” Then use the left/right arrow keys to access the “ResetDefault” submenu.

w Use the right/left arrow keys to select ON to perform a reset to defaults.

Press “Enter” to conﬁrm.

INFO

TIME INFO. Current Time

Shows the number of hours the ﬁxture has been operating since it was powered on.

w Access the menu by pressing the “Mode Esc” key. w Use the up/down arrow keys to reach the “INFO” menu and press

“Enter.” Then use the left/right arrow keys to access the “Time Info” submenu.

w Use the left/right arrow keys to select “Current Time”, and press “Enter”

to display the value.

Ttl Life Hrs

Shows the ﬁxture’s total number of hours of operation.

w Access the menu by pressing the “Mode Esc” key. w Use the up/down arrow keys to reach the “INFO” menu and press

“enter.” Then use the left/right arrow keys to access the access the “Time Info” submenu.

w Use the left/right arrow keys to select “Tlt Life Hrs”, and press “Enter” to

display the value.

Last Run Hrs

Shows the ﬁxture’s length of operation since the last time this counter was reset.

w Access the menu by pressing the “Mode Esc” key. w Use the up/down arrow keys to reach the “INFO” menu and press

“Enter.” Then use the left/right arrow keys to access the access the “Time Info” submenu.

w Use the left/right arrow keys to select “Tlt Life Hrs”, and press “Enter” to

display the value.

Timer PIN

The “Timer PIN” is the password required to reset the counter for “Last Run Hrs.” The PWD is 038.

w Access the menu by pressing the “Mode Esc” key. w Use the up/down arrow keys to reach the “INFO” menu and press

“Enter.” Then use the left/right arrow keys to select “Time Info.” Finally, use the left/right arrow keys to select “Timer PIN.”

w Scroll through using the left/right arrows until 038 appears and press

“Enter” to conﬁrm.

CLR LAST RUN

After entering the “Timer PIN”, you can reset the value for “Last Run Hrs” through this menu.

w Access the menu by pressing the “Mode Esc” key. w Use the up/down arrow keys to reach the “INFO” menu and press

“Enter.” Then use the left/right arrow keys to access “Clr Last Run” submenu.

w Use the left/right arrow keys to select “ON” to validate the reset.

TEMP. INFO Head Temp.

Shows the current temperature of the ﬁxture head.

w Access the menu by pressing the “Mode Esc” key. w Use the up/down arrow keys to reach the “INFO” menu and press

“Enter.” Then use the left/right arrow keys to access the “Temp.Info” submenu.

w Press “Enter” once again to display the temperature of the head.

Page 12

USER MANUAL _ 12

SOFTWARE VER

Displays the software version of the ﬁxture.

w Access the menu by pressing the “Mode Esc” key. w Use the up/down arrow keys to reach the “INFO” menu and press

“Enter.” Then use the left/right arrow keys to access the “Software ver” submenu.

w Press “Enter” once again to display the software version.

NETWORK

This menu directly displays the following network information for the ﬁxture: IP address, subnet mask and MAC address

w Access the menu by pressing the “Mode Esc” key. w Use the up/down arrow keys to reach the “INFO” menu and press

“Enter.” Then use the left/right arrow keys to access the “Network” submenu.

w Press “Enter” once again to display the information.

TEST

HOME

Allows you to reset the functions from a DMX controller. You can select these functions by adjusting the channel.

w Access the menu by pressing the “Mode Esc” key. w Use the up/down arrow keys to reach the “TEST” menu and press

“Enter.” Then use the left/right arrow keys to access the “Home” submenu.

w Press “Enter” once again to select “All” or “Pan&Tilt.”

TEST CHANNEL

Tests each of the ﬁxture’s settings (e.g., PAN, TILT).

w Access the menu by pressing the “Mode Esc” key. w Use the up/down arrow keys to reach the “TEST” menu and press

“Enter.” Then use the left/right arrow keys to access the “Test Channel” submenu.

w The ﬁxture then runs in test position. Use the left/right arrow keys to

scroll through and test each setting.

MANUAL CTRL.

Allows you to access all the ﬁxture’s settings manually (e.g., PAN, TILT). The shutter and the electronic dimmer are by default 100% open.

w Access the menu by pressing the “Mode Esc” key. w Use the up/down arrow keys to reach the “TEST” menu and press

“Enter.” Then use the left/right arrow keys to access the “Manual Ctrl” submenu.

w Use the left/right arrow keys to scroll through and check each setting.

CALIBRATION

Calibrates certain settings such as Pan, Tilt and Zoom. The password required to access the calibration function is 050.

w Access the menu by pressing the “Mode Esc” key. w Use the up/down arrow keys to reach the “TEST” menu and press

“Enter.” Then use the left/right arrow keys to access the “Calibration” submenu.

w Press “Enter” once again to access the password (050), and press

“Enter” to conﬁrm.

w Use the left/right arrow keys to move from one setting to another and

press “Enter” to access the calibration function of the setting. Finally, press “Enter” to conﬁrm the change.

PRESET

SELECT PROG.

Allows you to select the program for “Program Run.”

EDIT PROG.

Allows you to edit internal programs.

EDIT SCENES

Allows you to edit scenes within the internal programs.

SCENES INPUT

The luminaire features a DMX recorder, which can receive the scenes programmed on your DMX controller. Set the desired number of scenes from the control panel. Then run the scenes from your controller. They will be automatically transmitted to the WILDSUN K25.

MASTER/SLAVE MODE SETTINGS

A MASTER ﬁxture can send up to 3 different sets of data to a SLAVE ﬁxture (e.g., a MASTER ﬁxture can control 3 different SLAVE ﬁxtures which will each perform 3 different programs). The MASTER ﬁxture sends the 3 programs in a continuous loop.

The SLAVE ﬁxture receives data from the MASTER ﬁxture according to the group to which the SLAVE ﬁxture is assigned. For example, if the SLAVE ﬁxture has been assigned to “Slave 1” in the menu “Set to Slave”, the MASTER ﬁxture sends “Auto Program Part 1” to this SLAVE ﬁxture. If it was assigned to “Slave 2”, the SLAVE ﬁxture would receive the program “Auto Program Part 2” from the MASTER ﬁxture.

To launch a program, follow this procedure:

1. 1. Slave Settings - SLAVE ﬁxture adjustment Use the buttons to select “Function Mode.” Press ENTER to conﬁrm. Use the buttons to select “Set slave to.” Press ENTER to conﬁrm. Use the buttons to select “Slave 1”, “Slave 2” or “Slave 3.” Press ENTER to conﬁrm. Press MODE/ESC to return to the main menu.

2. 2. Automatic Program Run Use the buttons to select “Function Mode.” Press ENTER to conﬁrm. Use the buttons to select “Auto Program.” Press ENTER to conﬁrm. Use the buttons to select “Master” or “Alone.” “Master” sets the ﬁxture as the master. Press ENTER to conﬁrm. Press MODE/ESC to return to the main menu.

3. 3. Program selection for Auto Pro Part Use the buttons to select “Edit program.” Press ENTER to conﬁrm. Use the buttons to select “Select programs.” Press ENTER to conﬁrm. Select “Auto Program Part 1”, “Auto Program Part 2” or “Auto Program

Page 13

USER MANUAL _ 13

Part 3”, for the Slave program to be sent. Selecting “Part 1” will cause the SLAVE to run the same program as the MASTER ﬁxture. Press ENTER to conﬁrm. Press MODE/ESC to return to the main menu.

4. 4. Program selection for Edit Program Use the buttons to select “Edit program.” Press ENTER to conﬁrm. Use the buttons to select “Edit program.” Press ENTER to conﬁrm. Use the buttons to select the desired program. You can edit speciﬁc scenes in a given program. Press ENTER to conﬁrm. Press MODE/ESC to return to the main menu.

5. 5. Automatic Scene Recording Use the buttons to select “Edit program.” Press ENTER to conﬁrm. Use the buttons to select “Edit scenes.” Use the buttons to select the number of desired scenes. (maximum amount: 250 scenes) Press ENTER to conﬁrm. Press MODE/ESC to return to the main menu.

Example: ”Program 2” includes scenes: 10, 11, 12, 13. ”Program 4” includes scenes: 8, 9, 10. ”Program 6” includes scenes: 12, 13, 14, 15. ”Auto Program Part 1” is “Program 2.” ”Auto Program Part 2” is “Program 3.” ”Auto Program Part 3” is “Program 6.”

The 3 groups of SLAVE ﬁxtures run the “Auto Program” function in the following sequence:

Part 1:

Scene 10 Scene 11 Scene 12 Scene 13

Part 2:

Scene 8 cene 9 cene 10 Scene 8

Part 3:

Scene 12 Scene 13 Scene 14 Scene 15

LED MAPPING

The diagram shows the order of the LED addresses from a front view of the luminaire and control panel.

DMX CHART

THE following chart shows the functions and corresponding values for each DMX channel according to mode whether Standard (St), Basic (Ba) or Extended (Ex):

COSMOPIX-R (18 - 20 - 64 channels)

Mode/Channel Value Function

St Ba Ex

1 1 1

PAN Movement 8bit :

0-255 Pan Movement

2 2

Pan Fine 16bit

0-255 Fine control of Pan movement

3 2 3

TILT Movement 8bit :

0-255 Tilt Movement

4 4

Tilt Fine 16bit

0-255 Fine control of Tilt movement

5 3 5

Speed Pan/Tilt movement:

0-225 max to min speed

226-235 blackout by movement

236-235 no function

6 4

White LED - All arrays

0-255 White ( 0-Black , 255-100% White )

White LED - array 6

0-255 White ( 0-Black , 255-100% White )

Page 14

USER MANUAL _ 14

COSMOPIX-R (18 - 20 - 64 channels)

Mode/Channel Value Function

St Ba Ex

White LED - array 1

0-255 White ( 0-Black , 255-100% White )

White LED - array 2

0-255 White ( 0-Black , 255-100% White )

White LED - array 3

0-255 White ( 0-Black , 255-100% White )

White LED - array 4

0-255 White ( 0-Black , 255-100% White )

White LED - array 5

0-255 White ( 0-Black , 255-100% White )

White LED - array 6

0-255 White ( 0-Black , 255-100% White )

White LED - array 7

0-255 White ( 0-Black , 255-100% White )

Shutter, strobe:

0-31 Led trun off

32-63 Led turn on

64-95 Strobe effect slow to fast

96-127 Led turn on

128-159 Pulse-effect in sequences

160-191 Led turn on

192-223 Random strobe effect slow to fast

224-255 Led turn on

8 6 7

Dimmer intensity:

0-255 Intensity 0 to 100%

9 7 8

Chase Patterns:

0-15 Led trun off

16-31 Chase 1

32-47 Chase 2

48-63 Chase 3

64-79 Chase 4

80-95 Chase 5

96-111 Chase 6

112-127 Chase 7

128-143 Chase 8

144-159 Chase 9

160-175 Chase 10

176-191 Chase 11

192-207 Chase 12

208-223 Chase 13

224-239 Chase 14

240-255 Chase 15

10 8 9

Chase Speed:

0-125 Fast to Slow Backward

126-130 Stop(Speed=0)

131-255 Slow to Fast Forward

11 9 10

Chase Fade:

0-255 Fade Chase

12 10 11

Zoom :

0-255 Zoom adjustment from 60 to15

13 　 12

Zoom Fine :

0-255 Fine control for Zoom adjustment

14 11 21

Reset, internal programs:

0-79 Normal

80-84 All motor reset

85-87 Scan motor reset

88-90 no function

91-93 no function

94-96 no function

97-99 Others motor reset

100-119 Internal program 1 (secne1~8 of EEPROM)

120-139 Internal program 2 (secne9~16 of EEPROM)

140-159 Internal program 3 (secne17~24 of EEPROM)

160-179 Internal program 4 (secne25~32 of EEPROM)

180-199 Internal program 5 (secne33~40 of EEPROM)

200-219 Internal program 6 (secne41~48 of EEPROM)

220-239 Internal program 7 (secne49~56 of EEPROM)

240-255 no function

ERROR MESSAGES

When you turn on the WILDSUN K25, it will ﬁrst perform an automatic reset. The display may show “Err channel is XX” indicating there is a problem with one or more of the channels. “XX” represents channel 1, 2, 3, 4, 5 or 6, which contain the testing sensor for positioning. For example, the message, “Err channel is Pan movement”, indicates an error in channel

1. If there is an error on channel 1 and channel 3 at the same time, the following error message may appear: “Err channel is Pan movement”, “Err channel is Tilt movement”. The system will ﬂash twice, and the ﬁxture will generate a second reset. If the error message persists after more than two resets, the channels showing errors will not work properly but the other channels will function normally.

Please contact your authorized dealer or manufacturer for service and do not attempt to repair the luminaire yourself.

PAN- MOVEMENT ER

(PAN-yoke movement error): This message will appear after the reset if the yoke’s magnetic-indexing circuit malfunctions (failed sensor or magnet missing) or the stepping-motor is defective (also caused by its driving IC on the main PCB). The PAN- movement does not return to the default position after the reset.

TILT- MOVEMENT ER

(TILT-head movement error): This message will appear after the reset if the head’s magnetic-indexing circuit malfunctions (sensor failed or magnet missing) or the stepping-motor is defective (also caused by its driving IC on the main PCB). The TILT- movement does not return to the default position after the reset.

CARE AND MAINTENANCE

The care and maintenance of your WILDSUN K25 should be ensured by a qualiﬁed technician. Your WILDSUN K25 requires regular servicing. The frequency depends essentially on its operating conditions and

Page 15

USER MANUAL _ 15

environment. Intensive use in a dusty environment, or a lack of ventilation around the ﬁxture, may disrupt operation, result in overheating and cause damage that is not covered by the warranty.

WARNING!

Disconnect from mains before servicing.

UPDATING THE LUMINAIRE

Ayrton is continually upgrading this product line. It is therefore possible that a new software version is available that will increase the unit’s capabilities.

Updates are performed using Ayrton’s update box. Contact your dealer for more information.

To display the version of your device, go into the “Info” menu and select “Software version” (see options details under the “INFO” menu). It is advisable to use the same software version for multiple ﬁxtures.

CLEANING

Your WILDSUN K25 requires cleaning at regular intervals. Be aware that accumulated dust and residue on the air vents, body and glass of the ﬁxture may reduce efﬁciency and impair proper operation.

Before cleaning, disconnect the power cable from source.

Use compressed air to blow away dust particles accumulated on and between the cooling ﬁns at the rear of the luminaire’s optical system.

Clean the glass of the ﬁxture with a slightly damp soft cloth. When necessary, use a non-alcohol-based glass cleaner. Never use harsh solvents!

WARNING!

Never use alcohol or any chemical agent to clean the optical system of an Ayrton product.

COMPLIANCE CHECK

Your installation should be checked regularly by certiﬁed service center. In addition, the following should be checked once a year by a qualiﬁed technician:

• The ﬁxture’s attachment system must be correctly installed and show no sign of corrosion.

• The ﬁxture’s mounting bracket should not be distorted in any way or show any trace of corrosion.

• The safety cable should be attached at the appropriate spot.

• Mechanical parts should show no sign of wear.

• The electrical cables should show no sign of wear, cuts or splices.

TECHNICAL SPECIFICATIONS

OPTICAL

• High-efﬁciency optical system

• Opening angle of the beam: 10° to 60°

LIGHT SOURCE

• 217 high-power white mono-chip LED emitters

• Brightness: up to 100000 lumens

• Estimated lifespan of LED emitters: 50,000 hours

• Guaranteed “no-ﬂicker” effect perfectly suited for television applications and all video recorded events

DIMMER, STROBE

• Electronic dimmer for light adjustment from 0 to 100% without color change (16-bit)

• High-speed strobe effect in white or color at 1 to 25 ﬂashes/second

• Pre-programmed variable strobe effects

SOFTWARE FEATURES

• Full menus for setting DMX address and advanced functions

• Compatible with the DMX/RDM (Remote Device Management) protocol

• Pre-programmed macro modes

• Information menu including: timer, temperature, software version, etc.

CONTROL

• USITT DMX512

• Automatic features for managing your luminaire without a DMX console

• DMX RDM-compatible

• Integrated control panel with LCD display and 6 buttons

• DMX512 input/output

• Choice of 3 DMX modes (from 11 to 21 channels)

• Wireless System: LumenRadio wireless CRMX RDM receiver

POWER SUPPLY

• Electronic power distribution with Power Factor Correction (PFC) from 110-240 VAC, 50/60 Hz

• 2750 Watt maximum power

• Power supply via powerCON 32A connector

• Supplied AC power cable plug

COOLING

• Advanced forced-air cooling system

• Self-adjusting fan for reduced noise level (in AUTO mode)

• User-selectable air-cooling modes

CONSTRUCTION

• Covers: molded PC-ABS thermoplastic, class V0 (ﬁre retardant)

• Chassis: steel plates and aluminum

• 2 handles for transport

• Protection rating: IP20 (indoor use only)

• Finish: Carbon black

INSTALLATION

• 2 OMEGA brackets with quarter-turn locks included

• Safety cable attachment

Page 16

USER MANUAL _ 16

OPERATING PARAMETERS

• Operating positions: on ﬂoor or attached to a support (no ﬂag positioning)

• Maximum authorized ambient temperature (Ta Max): 45°C (113°F)

• Minimum authorized ambient temperature (Ta Min): -10°C (14°F)

• Minimum projection distance: 5 m

DIMENSIONS

• Product: 539 mm x 696 mm x 348 mm (L x H x D)

• Protective foam: 600 mm x 720 mm x 410 mm (L x H x D)

WEIGHT

• Product: 38 kg

• Product in packaging with accessories: 55kg

PRODUCT CODE

• 013820: WILDSUN K25 AUTOMATED LUMINAIRE

FOAM FOR FLIGHT CASE

WILDSUN K25 is delivered in a carton packed with a dense, protective foam surrounding the ﬁxture. This reusable protective shell is intended for a ﬂight case that can be custom built for the luminaire.

AYRTON does not offer custom ﬂight cases for the WILDSUN K25. This accessory is to be provided by the user. The main dimensions of the protective shell appear in the following diagram:

488

602

421

R15

WARRANTY

The AYRTON WILDSUN K25 ﬁxture is guaranteed against manufacturing defects for the duration of one (1) year from the date of purchase. This warranty does not cover the unit for evidence of physical shock or damage caused by abuse or any use not in accordance with the operating conditions set forth in the present user manual.

In addition, cosmetic defects caused by the normal wear and tear of the unit are not covered under the warranty.

Any modiﬁcation to the ﬁxture will void the warranty. AYRTON cannot under any circumstances be held liable for quality and conformity regarding the installation of this product, which is the responsibility of the installer.

Broken glass lenses on the WILDSUN K25, and any damage that could arise thereof, are excluded from the warranty. Any possible cosmetic defects, provided you report them to your AYRTON dealer upon unpacking the device and before use, may be covered by the warranty.

Note: The manufacturer is not responsible for any errors or omissions that may occur in this document. All information contained in this manual is subject to change without notice.

Page 17

USER MANUAL _ 17

Page 18

www.ayrton.eu