Ayrton Arcaline3 Instruction Manual

Download

Page 1

Manuel d’utilisation

KEEP THIS MANUAL FOR FUTURE NEEDS

Page 2

ARCALINE 3 User Manual XM1362-V1.0-NR

CONTENTS

1. SAFETY INSTRUCTIONS 2

2. FEATURES 3

3. FIXTURE OVERVIEW 5

4. DIMENSIONAL DRAWINGS 6

5. INSTALLATION 7

6. DMX-512 CONTROL CONNECTION 10

7. DEVICE DMX START ADDRESS SELECTION 11

8. DISPLAY 11

10. DMX PROTOCOL 18

11. ERROR MESSAGES 23

12. CLEANING AND MAINTENANCE 24

! ! ! ! ! ! ! ! ! ! ! ! !

Page 3

ARCALINE 3 User Manual XM1362-V1.0-NR

1. SAFETY INSTRUCTIONS

1.1. IMPORTANT SAFETY WARNING

This device has left the factory in perfect condition. In order to maintain this condition and to ensure safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual.

In order to install, operate, and maintain the lighting fixture safely and correctly we suggest that the installation and operation be carried out by qualified technicians and these instructions be carefully followed.

CAUTION!

HIGH VOLTAGE. RISK OF SEVERE OR FATAL ELECTRIC SHOCK

CAUTION!

ALWAYS DISCONNECT MAINS SUPPLY BEFORE REMOVING ANY FIXTURE COVERS

CAUTION!

NEVER LOOK DIRECTLY INTO THE LIGHT SOURCE. SENSITIVE PERSONS MAY SUFFER AN EPILEPTIC SHOCK

CAUTION!

NEVER TOUCH THE DEVICE DURING OPERATION! COVERS MAY BE HOT

Important: Damage caused by the disregard of this user manual is not subject to warranty. The dealer and manufacturer will not accept liability for any resulting defects or problems.

• If the device has been exposed to temperature changes due to environmental conditions,

do not power on immediately. The resulting condensation could damage the device. Leave the device powered off until it has reached room temperature.

• This device falls under protection-class I. Therefore, it is essential that the device be

earthed.

• If either lenses or display are damaged (damage may include cracks or gashes in the

material) they must be replaced.

• Electrical connections, such as replacing the power plug, must be performed by a

qualified person.

• Make sure that the available voltage is not higher than that which is stated at the end of

this manual.

• Make sure the power cord is never crushed or damaged by sharp edges. Should the power

cord suffer If this should be the case, replacement of the cable must be done by an authorized dealer.

• If the external flexible power cord of this device is damaged, it shall be exclusively

replaced by the manufacturer or their service agent or a similar qualified person in order to avoid injury.



Page 4

ARCALINE 3 User Manual XM1362-V1.0-NR

• When the device is not in use or before performing maintenance, always disconnect the

device from the mains. Only handle the power cord from the plug. Never pull the plug out of a socket by tugging the power cord.

• When powered on for the first time, some smoke or smell may occur. This is caused by

coating on metal parts when heated and is normal. If you are concerned, please contact your distributor.

• Do not focus the beam onto flammable surfaces. The minimum distance between the

exiting lens of the device and the illuminated surface must be greater than 0.5 meter.

Please be aware that damage caused by any modifications to the device are not subject to warranty. Keep away from children and non-professionals.

1.2. GENERAL GUIDELINES

• This device is a lighting effect for professional use on stages, in discotheques, theatres,

etc., the device was designed for indoor or outdoor use.

• This fixture is only allowed to be operated within the maximum alternating current as

stated in the technical specifications in section 2 of this manual.

• Handle the device with care, avoid shaking or using force when installing or maintaining

the device.

• When choosing the installation location, please make sure that the device is not exposed

to extreme heat, moisture or dust.

• If you use the quick lock cam when rigging the device, make sure the quick lock fasteners

are located in the quick lock holes correctly and securely.

• Operate the device only after having familiarized yourself with its functions. Do not

permit operation by persons not qualified for operating the device. Most damages are the result of unprofessional operation.

• Please use the original packaging if the device is to be transported.

• The applicable temperature for the device is between -10°C to 45°C. Do not use the

device outside of this temperature range.

For safety reasons, please be aware that all modifications to the device are forbidden. If this device is operated in any way different to the ones described in this manual, the product may suffer damage and the warranty becomes void. Furthermore, any other operation may lead to short-circuits, burns, electric shocks etc.

2. FEATURES

POWER SUPPLY

• AC 100-240V~ 50-60Hz

• Power Consumption: 180W

Page 5

ARCALINE 3 User Manual XM1362-V1.0-NR

OPTICS

• LED: 12x10W High-Power LEDs, RGBW 4 in 1 LED make extremely even and smooth

color mixing effect

• RGBW 4 in 1 LED make extremely even and smooth color mixing effect

• Extremely long Life: 50,000H and low power consumption

COLORS

• Excellent color mixing and rainbow effect

• Color temperature linear adjust from 2700K to 8000K, preset color temperature scenes with:

2700K, 3200K, 4300K, 5600K, 6500K, 8000K options

FEATURES

• 3 Control channel modes: 13 / 6 / 9 channels

• 2 operations modes: DMX-512, Master / Slave modes

• Pixel Control: can make extremely chasing effect

• Strobe effect with 1-25 flashes per second and pulse effect

• General dimming and blackout for all four colors

• IP65 outdoor use

DISPLAY

• Advanced and convenient full –color LCD touch screen

• Locked automatically after standby for 15 seconds to prevent error; hold the button for 3

seconds to activate

SOFTWARE

7 pre-installed programs available upon selection

Upgrades: fast and convenient through DMX cable

Reset DMX address, remote lamp switch, reset can all be done by the controller OTHER SPEC

Input signal isolation: guarantees stable signal transmission without interference

Advanced RDM function

WHIGHT

Net weight: 11 kg

Page 6

ARCALINE 3 User Manual XM1362-V1.0-NR

3. FIXTURE OVERVIEW

1 Body of the unit

2 Glass

3 Display

4 Mode/esc- button

5 Down-button

6 Right-button

7 Up-button

8 Valve

9 Hook for safty cable

10 Power out

11 Power in

Page 7

ARCALINE 3 User Manual XM1362-V1.0-NR

4. DIMENSIONAL DRAWINGS

Page 8

ARCALINE 3 User Manual XM1362-V1.0-NR

5. INSTALLATION

CAUTION!

DO NOT OPERATE THIS DEVICE WITH OPEN COVER

5.1. RIGGING THE DEVICE

CAUTION!

PLEASE CONSIDER THE GB7000.1-2015, GB7000.217-2008 AND THE OTHER RESPECTIVE NATIONAL NORMS DURING THE INSTALLATION. THE INSTALLATION MUST ONLY BE CARRIED OUT BY A QUALIFIED PERSON.

• The structure on which the device is rigged must be able to support 10 times the weight of

the device for 1 hour without any critical deformation occurring.

• The installation must always be secured with a secondary safety attachment, e.g. the

included appropriate safety cable.

• Never stand directly below the device when rigging, de-rigging or maintaining the device.

• All electrical connections should be approved by a qualified electrician prior to using the

product.

• When the device is permanently installed these installations have to be approved by a

qualified person once a year.

• Overhead rigging requires extensive experience, including (but not limited to) calculating

working load limits, specifying installation/ rigging materials, and periodic safety inspection of all installation material as well as the device. If you lack these qualifications, do not attempt the rigging of this device yourself. Improper installation/ rigging can result in serious bodily injury.

• Before rigging make sure that the installation area can hold a minimum point load of 10

times the device’s weight.

Page 9

ARCALINE 3 User Manual XM1362-V1.0-NR

5.2. RIGGING USING THE OMEGA BRACKETS

In the event that the unit is to be fixed to a tubular structure, the stands supplied with the ARCALINE 3 can be replaced with tube clamps and fixed to the unit by corresponding screws/nuts (clamps and hardware not included).

The following illustration shows an ARCALINE 3 fitted with tube clamps :

Important:

This step is very important to ensure safe rigging of the fixture.

5.3. Orientation of the unit

The floor stands can be installed in two different ways. It is therefore possible to obtain two types of directional settings on the unit, as shown in the following diagrams :



Page 10

ARCALINE 3 User Manual XM1362-V1.0-NR

5.4. Installation of the diffuser filters on the ARCALINE 3

The ARCALINE 3 can be fitted with specially-designed diffuser filters, enable the angle of the unit’s beam to be adjusted, depending on the application for which it is intended.

CAUTION!

ONLY USE ORIGINAL AYRTON FILTERS IN THE ARCALINE 3

The ARCALINE 3 has an internal filter holder to house the diffuser filters.

These specially-designed diffuser filters are manufactured by AYRTON and are available in several versions, depending on the diffusion Angle required. They come in the form of a kit with two 2 translucent plates, each covering half of the projector’s LED groups.

In order to install the filters, each plate must be inserted into the unit on one end, and both sides of the projector must therefore be opened.

Details of the filters installation :

• Unscrew the three HEX screws (number 1) with the help of a 2.5 mm hex key

• Remove the removable casing (number 2)

• Unscrew the two screws (number 3) using a Philips screwdriver

• Remove the plate (number 4) covering access to the filter housing, as well as its waterproof

seal (number 5)

• Take a filter and remove the protective films stuck to each side. From then on take care to

hold the filter by the edges and avoid touching the sides

• Insert the filter fully into the housing provided for this purpose (see diagram below), making

sure the granular side of the filter faces the glass on the unit.

Page 11

ARCALINE 3 User Manual XM1362-V1.0-NR

• Replace the plate (number 4) covering access to the filter housing and its waterproof seal

(number 5), then screw the parts in place by tightening the two Philips head screws (number

• Place the removable casing (mark 2) and fix to the unit by tightening both HEX screws

(number 1) Repeat this procedure to install the second filter on the other side of the unit

6. DMX-512 CONTROL CONNECTION

Connect the provided male side of the XLR cable to the female XLR output of your controller and the female side of the XLR cable to the male XLR input of the device. You can connect multiple devices together in a serial fashion. The cable needed should be two core, screened cable with XLR input and output connectors. Please refer to the diagram below.

Page 12

ARCALINE 3 User Manual XM1362-V1.0-NR

7. DEVICE DMX START ADDRESS SELECTION

All fixtures should be given a DMX starting address when using a DMX signal, so that the correct fixture responds to the correct control signals. This digital starting address is the channel number from which the fixture starts to “listen” to the digital control information sent out from the DMX controller. The allocation of this starting address is achieved by setting the correct address number on the display located on the base of the device. You can set the same starting address for all fixtures or a group of fixtures, or set different addresses for each fixture individually.

If you set the same address on all devices, all the devices will start to “listen” to the same control signal from the same channel number. In other words, changing the settings of one channel will affect all the fixtures simultaneously. If you set a different address, each unit will start to “listen” to the channel number you have set, based on the quantity of control channels of the unit. That means changing the settings of one channel will affect only the selected device.

In the case of the led fixtures, which is a 13 channel fixture, you should set the starting address of the first unit to 1, the second unit to 14(13 + 1), the third unit to 27 (13+ 14), and so on.

8. DISPLAY

The Display offers several features: you can set the starting address, run the pre-programmed program or reset the device.

The main menu is accessed by pressing the -button until the display starts flashing. Browse

through the menu by pressing the -button , -button . Press the -button in order

to select the desired menu. You can change the selection by pressing the -button ,

-button. Confirm every selection by pressing the -button. You can leave every mode by

pressing the -button. After accessing the edit mode, the unit will automatically exit to the main menu after 15 seconds from the last button press. When the unit is powered on, if no data signal is connected after 1 minute, then the display will switch off automatically.

Page 13

ARCALINE 3 User Manual XM1362-V1.0-NR

Default settings shaded

Address

Set Dmx Address

A001~AXXX

DMX address setting

Users Mode

User Mode

Stand Mode Basic Mode Extend Mode Pixel Mode User Mode A User Mode B User Mode C

User’s mode to change channel numbers

Edit UserModeA :

Max channel Auto Prog :

Preset User modes A,B,C :

Options

Status

No DMX Mode

Close/Hold/Auto

Auto run if no DMX

Service PIN

Service PIN RDM UID

Set Type Change To BIN

Password=XXX Xxxxxx

LED BIN LED BIN

Service Password”=050”

RDM PID Code LED BIN LED BIN

Disp.Setting

Shutoff Time Flip Display Key Lock DispFlash

02~60m 05m ON/OFF ON/OFF ON/OFF

Display shutoff time Reverse 180 degree Key Lock DispFlash

Flip Pixel

ON/OFF

LED reverse order

Temp. C/F

Celsius Fahrenheit

Temperature switch between /

Trigger

DMX Value Disp. Set To Slave Auto Program

Auto Prog…… Slave1,Slave2,Slave3 Master / Alone

DMX Value Disp. Set To Slave Auto Program

ResetDefault

ON/OFF

Restore factory set.

Info

Time Info.

Current Time Ttl Life Hrs Last Run Hrs Timer PIN Clr Last Run

XXXX(Hours) XXXX(Hours) XXXX(Hours) Password=XXX ON/OFF

Temp. Info

Head Temp.

XXX/

Software Ver

V x.x.x

Software version

Test

Test Channel

Auto Prog……

Test function

Manual Ctrl.

Auto Prog =XXX

Fine adjustment of the lamp

Page 14

ARCALINE 3 User Manual XM1362-V1.0-NR

9.1. Address

Set DMX Address

With this function, you can adjust the desired DMX-address via the Display.

1. Access the main menu.

2. Tap the <Up/Down> button until “Set DMX Address” is displayed.

3. Press ENTER, the display will show “Set DMX Address”.

4. Tap the <Up/Down> button, the display will show “A001~AXXX”

5. Press ENTER to confirm or press <MODE/ESC> to return to the main menu.

9.2. USERS MODE

9.2.1. User Mode

1Tap <MODE/ESC> button, access the main menu, Tap the <Up/Down> button until

“Users mode” is displayed. Press <ENTER>, the display will show “Users mode”.

2The display shows “User Mode” , Press <Up/Down> button, then you can choose “Edit

User Mode A”, “Edit User Mode B” and “Edit User Mode C”.

3Press <ENTER> to confirm or press <MODE/ESC> to exit

As well as Standard Mode, Basic Mode and Extended Mode, this fixture has another three DMX modes which can be set according to user's needs. To set one of these user modes see below:

1Tap <MODE/ESC> button, access the main menu, Tap the <Up/Down> button until

“Users mode set” is displayed. Press <ENTER>, the display will show “Users mode set”.

2Choose “Edit User Mode A”, press “ENTER” 3Set “Max Channel=xxx” the max channel 4Set “Edit User Mode B” and “Edit User Mode C” as above

9.2.2. Edit User Mode A

With this function, you can adjust the rest user defined channel order.

1Tap <MODE/ESC> button, access the main menu, Tap the <Up/Down> button until

“Users mode” is displayed. Press <ENTER>, the display will show “Users mode”.

2The display show “Edit User Mode A” first channel, Press <Up/Down> the display will

show “Edit User Mode A”.

3Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.

9.3. Options

9.3.1. Status No DMX Mode

With this function, when the drive is not DMX signal, it runs automatism, close, hold and music, the default is hold.

1. Access the main menu.

2. Press <Up/Down>, the display will show No DMX Mode.

3. Press< ENTER>, the display will show No DMX Mode.

4. The display show Hold,Press <Up/Down>, the display will show “Close”, “Auto”,

“Music”.

5. Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.

Page 15

ARCALINE 3 User Manual XM1362-V1.0-NR

9.3.2. Service PIN

Service PIN——The Password for this function is “50”.

RDM UID—— With this function you can call up various submenus via RDM.

This device is RDM ready. RDM stands for "remote device management" and makes remote control of devices connected to the DMX-bus. ANSI E1.20-2006 by ESTA specifies the RDM standard as an extension of the DMX512 protocol.

Manual settings like adjusting the DMX starting address are no longer needed. This is

especially useful when the device is installed in a remote area. RDM ready and conventional DMX devices can be operated in one DMX line. The RDM protocol sends own packages in the DMX512 data feed and does not influence conventional devices.

If DMX splitters are used and RDM control is to be used, these splitters must support RDM. The number and type of RDM parameters depend on the RDM controller being used.

Set Type

1. Access the main menu.

2. Press <Up/Down>, the display will show Set Type.

3. Press< ENTER>, the display will show Set Type.

4. The display show “LED BIN”.

5. Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.

Change TO BIN

1. Access the main menu.

2. Press <Up/Down>, the display will show Change TO BIN.

3. Press< ENTER>, the display will show Change TO BIN.

4. The display show “LED BIN”.

5. Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.

9.3.3. Display Setting Shut off time

With this function you can shut off the LCD display after 2 to 60 minutes.The default is 5 minutes.

Flip Display

With this function you can rotate the display by 180°.

1Tap <MODE/ESC> buttonaccess the main menuTap the <Up/Down> button until

“Options” is displayed. Press ENTER, the display will show “Options”. Tap the <Up/Down> button until the display will show “Display Setting”. Press ENTER, the display will show “Display Setting”.

2Press <Up/Down>, the display will show “Flip Display”. 3Press< ENTER>, the display will show “Flip Display”. 4The display show “OFF”, Press <Up/Down>, the display will show “ON” 5Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.

Page 16

ARCALINE 3 User Manual XM1362-V1.0-NR

Key Lock

With this function you can activate the automatic key lock function. If this function is activated, the keys will be locked automatically after exiting the edit mode for 15 seconds. keeping press the <MODE/ESC> key for 3seconds if you do not need this function.

1Tap <MODE/ESC> buttonaccess the main menuTap the <Up/Down> button until

“Personality” is displayed. Press < ENTER>, the display will show “Personality”. Tap the <Up/Down> button until the display will show “Display Setting”. Press ENTER, the display will show “Display Setting”.

2Press <Up/Down>, the display will show “Key Lock”. 3Press< ENTER>, the display will show “Key Lock”. 4The display show “OFF”, Press <Up/Down>, the display will show “ON”. 5Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.

Displ Flash

With this function you can the entire display to be flipped by 180˚ to allow for better view

when the fixture is hung from truss or a ceiling. This function is disabled as default.

1Tap <MODE/ESC>button  access the main menu  Tap the <Up/Down>button

until ”Personality” is displayed. Press ENTER, the display will show “Personality”. Tap the <Up/Down>button until the display will show “Display Setting”. Press ENTER, the display will show “Display Setting”.

2Press <Up/Down>, the display will show ”Display Reverse”. 3Press< ENTER>, the display will show ”Display Reverse”. 4The display show “OFF”, Press <Up/Down>, the display will show “ON”. 5Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.

9.3.4. Flip Pixel

1. Tap <MODE/ESC> buttonaccess the main menu, Tap the <Up/Down> button until

“Options” is displayed. Press ENTER, the display will show “Options”.

2. Press <Up/Down>, the display will show “Flip Pixel”.

3. Press< ENTER>, the display will show “Flip Pixel”.

4. The display show “OFF”, Press <Up/Down>, the display will show “ON”.,

5. Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.

9.3.5. Temp. C/F

With this function, Display the temperature for Celsius or Fahrenheit.

1Access the main menu. 2Press <Up/Down>, the display will show Temp. C/F. 3Press< ENTER>, the display will show Temp. C/F. 4The display show Fahrenheit,Press <Up/Down>, the display will show “Celsius”. 5Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.

9.3.6. Trigger

DMX Value Disp.

With this function you can display the DMX 512 value of each channel. The display automatically shows the channel with a value changing.

1. Access the main menu.

2. Tap the <Up/Down>button until DMX Value Disp.is displayed.

3. Press ENTER, the display will show DMX Value Disp..

Page 17

ARCALINE 3 User Manual XM1362-V1.0-NR

4. Tap the <Up/Down>buttonchoose each channel.

5. Press ENTER to confirm or press <MODE/ESC> to return to the main menu.

Set To Slave

With this function, you can define the device as slave.

1. Access the main menu.

2. Tap the <Up/Down>button until Set To Slaveis displayed.

3. Press ENTER, the display will show Set To Slave.

4. Tap the <Up/Down>buttonthe display will show “Slave1”, ”Slave2”, ”Slave3”.

5. Press ENTER to confirm or press <MODE/ESC> to return to the main menu.

Auto Program

With this function, you can run the internal program. You can select the desired program under “Select program”. You can set the number of steps under “Edit program”. You can edit the individual scenes under “Edit scenes”. With this function, you can run the individual scenes either automatically, i.e. with the adjusted Step-Time.

1. Access the main menu.

2. Tap the <Up/Down>button until Auto Programis displayed.

3. Press ENTER, the display will show Auto Program.

4. Tap the <Up/Down>buttonthe display will show “Master1”, ” Alone”.

5. Press ENTER to confirm or press <MODE/ESC> to return to the main menu.

9.3.7. ResetDefault

With this function, you can select restore factory set for ON or OFF, the default is OFF.

1Access the main menu. 2Press <Up/Down>, the display will show ResetDefault. 3Press< ENTER>, the display will show ResetDefault. 4The display show OFF,Press <Up/Down>, the display will show “ON”. 5Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.

9.4. Info

9.4.1. Time info. Current Time

With this function, you can display the temporary running time of the device from the last power on. The display shows “XXXX”, “XXXX” stands for the number of hours. The counter is resetted after turning the device off.

1. Access the main menu.

2. the display will show Time Information.

3. Press <Up/Down>, the display will show Current Time.

4. Press< ENTER>, the display will show Current Time.

5. The display will show XXXX (Hours) 

6. Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.

Ttl Life Hrs

With this function, you can display the running time of the device. The display shows “XXXX”, “XXXX” stands for the number of hours.

1. Access the main menu.

2. Press <Up/Down>, the display will show Ttl Life Hrs.

3. Press< ENTER>, the display will show Ttl Life Hrs.

Page 18

ARCALINE 3 User Manual XM1362-V1.0-NR

4. The display will show XXXX (Hours) 

5. Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.

Last Run Hrs

With this function, you can display last the running time of the lamp. The display shows “XXXX”, “XXXX” stands for the number of hours

1. Access the main menu.

2. Press <Up/Down>, the display will show Last Run Hrs.

3. Press< ENTER>, the display will show Last Run Hrs.

4. The display will show XXXX (Hours) 

5. Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.

Timer PIN

With this function, you can display the timer password.

1. Access the main menu.

2. Press <Up/Down>, the display will show Timer PIN.

3. Press< ENTER>, the display will show Timer PIN. The time password is 038.

4. Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.

Clr Last Run

With this function, you can clear last run time of the fixture. The display shows “ON” or “OFF”, Press “Enter” to confirm.

1. Access the main menu.

2. Press <Up/Down>, the display will show Clr Last Run.

3. At Timer PINmenu input right password, Press< ENTER>, the display will show Clr Last Run.

4. The display show OFF,Press <Up/Down>, the display will show ON.

5. Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.

9.4.2. Temp. Info Head Temp.

With this function you can display the temperature on the display board of the base (near CMY-filter) in Celsius.

1. Access the main menu.

2. Press <Up/Down>, the display will show Head Temp..

3. Press< ENTER>, the display will show Head Temp..

4. The display show “XXX C/ F”.

5. Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.

9.4.3. Software ver

With this function, you can display the software version of the device.

1. Access the main menu.

2. Press <Up/Down>, the display will show Software ver.

3. Press< ENTER>, the display will show Software ver.

4. The display show “Ver x.x”.

5. Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.

9.5. Test

Page 19

ARCALINE 3 User Manual XM1362-V1.0-NR

9.5.1. Test Channel

With this function you can test each channel on its (correct) function.

1Access the main menu. 2Press <Up/Down>, the display will show Test Channel. 3Press< ENTER>, the display will show Test Channel. 4The display show Pan Movingfrist channel, Press <Up/Down>, can choose other

channel.

5Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.

9.5.2. Manual Ctrl.

With this function, you can adjust the lamp more easily. All effects will be canceled, the shutter opens and the dimmer intensity will be set to 100 %. With the individual functions, you can focus the light on a flat surface (wall) and erform the fine lamp adjustment.

1Access the main menu. 2Press <Up/Down>, the display will show Manual Ctrl.. 3Press< ENTER>, the display will show Manual Ctrl.. 4The display show PAN=XXX. 5Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.

10. DMX PROTOCOL

DMX channel´s functions and their values (57DMX channels):

Mode/Channel

Value

Function

Ba E



1 1 



Red LED -all arrays :

0-255

Red ( 0-Black , 255-100% Red )

2 2 



Green LED-all arrays :

0-255

Green ( 0-Black , 255-100% Green )

3 3 



Blue LED -all arrays :

0-255

Blue ( 0-Black , 255-100% Blue )

4 4 



White LED -all arrays :

0-255

White ( 0-Black , 255-100% White )



10 1 

Red LED -array 1 :



0-255

Red ( 0-Black , 255-100% Red )



11 2 

Green LED-array 1 :



0-255

Green ( 0-Black , 255-100% Green )



12 3 

Blue LED -array 1 :



0-255

Blue ( 0-Black , 255-100% Blue )



13 4 

White LED -array 1 :



0-255

White ( 0-Black , 255-100% White )

Page 20

ARCALINE 3 User Manual XM1362-V1.0-NR



14 5 

Red LED -array 2 :



0-255

Red ( 0-Black , 255-100% Red )



15 6 

Green LED-array 2 :



0-255

Green ( 0-Black , 255-100% Green )



16 7 

Blue LED -array 2 :



0-255

Blue ( 0-Black , 255-100% Blue )



17 8 

White LED -array 2 :



0-255

White ( 0-Black , 255-100% White )



……



4 5



Red LED -array 12 :

0-255

Red ( 0-Black , 255-100% Red )



4 6



Green LED-array 12 :

0-255

Green ( 0-Black , 255-100% Green )



4 7



Blue LED -array 12 :

0-255

Blue ( 0-Black , 255-100% Blue )



4 8



White LED -array 12 :

0-255

White ( 0-Black , 255-100% White )

5 5 1



Shutter, strobe:

0-31

Led trun off

32-63

Led turn on

64-95

Strobe effect slow to fast

96-127

Led turn on

128-159

Pulse-effect in sequences

160-191

Led turn on

192-223

Random strobe effect slow to fast

224-255

Led turn on

6 6 2



Dimmer intensity:

0-255

Intensity 0 to 100%

 3 



Color Macro:

0-7

No function

8-39

from RED to YELLOW

40-71

from YELLOW to GREEN

72-103

from GREEN to CYAN

104-135

from CYAN to BLUE

136-167

from BLUE to MAGENTA

168-199

from MAGENTA to RED

200-231

from RED to WHITE

Page 21

ARCALINE 3 User Manual XM1362-V1.0-NR

232-255

Crossfading colours from slow to fast

 4 



Color Presets:

0-4

No function

5--9

White2700k

10--14

White3200k

15-19

White4200k

20-24

White5600k

25-29

White6500k

30-34

White8000k

35-39

Yellow

40-44

Magenta

45-49

Cyan

50-54

Salmon

55-59

Turquoise

60-64

Light Green

65-69

Steel Blue

70-74

Orange

75-79

Straw

80-84

Pale Lavander

85-89

Pink

90-94

Red

95-99

Green

100-104

Blue

105-109

Rainbow1

110-114

Rainbow2

115-119

Rainbow3

120-124

Rainbow4

125-129

Rainbow5

130-134

Rainbow6

135-139

Rainbow7

140-144

Rainbow8

145-149

Rainbow9

150-154

Rainbow10

155-159

Rainbow11

160-164

Rainbow12

165-169

Rainbow13

170-174

Rainbow14

Page 22

ARCALINE 3 User Manual XM1362-V1.0-NR

175-179

Rainbow15

180-184

Rainbow16

185-189

Rainbow17

190-194

Rainbow18

195-199

Rainbow19

200-255

Reserved

 5 



Color Presets Dimmer:

0-255

Dimmer 0% to 100%

 6 



Chase Patterns:

1--14

Led trun off

15-30

Chase 1

31-46

Chase 2

47-62

Chase 3

63-78

Chase 4

79-94

Chase 5

95-110

Chase 6

111-126

Chase 7

127-142

Chase 8

143-158

Chase 9

159-174

Chase 10

175-190

Chase 11

191-206

Chase 12

207-222

Chase 13

223-238

Chase 14

239-255

Chase 15

 7 



Chase Speed:

0-125

Fast to Slow Backward

126-130

Stop(Speed=0)

131-255

Slow to Fast Forward

 8 



Chase Fade:

0-255

Fade Chase

 9 



internal programs:

0-79

Normal

80-84

no function

85-87

no function

88-90

no function

91-93

no function

Page 23

ARCALINE 3 User Manual XM1362-V1.0-NR

94-96

no function

97-99

no function

100-119

Internal program 1 (secne1~8 of EEPROM)

120-139

Internal program 2 (secne9~16 of EEPROM)

140-159

Internal program 3 (secne17~24 of EEPROM)

160-179

Internal program 4 (secne25~32 of EEPROM)

180-199

Internal program 5 (secne33~40 of EEPROM)

200-219

Internal program 6 (secne41~48 of EEPROM)

220-239

Internal program 7 (secne49~56 of EEPROM)

240-255

Reserved

Page 24

ARCALINE 3 User Manual XM1362-V1.0-NR

11. ERROR MESSAGES

When you turn on the device, it will first perform a reset. The display may show ”Err channel is XX” should there be problems with one or more functions. “XX” stands for channel 1, 2, 3, 4, 5, 6 etc whose sensor has encountered a problem. For example, when the display shows “Err channel is Pan movement”, it means there is an error on channel 1. If there are errors on channel 1, channel 3, channel 6 at the same time, you may see the error message, “Err channel is Pan movement”, “Err channel is Tilt movement”“ “Err channel is Shutter” ,flash twice, and then the device will generate a second reset. If the error messages persist after performing a reset more than twice, the channels which have errors may not work properly however, all other functions can work as usual. Please contact your dealer or manufacturer for service. Self repair is not allowed.

PAN- movement Er

(PAN- yoke movement error) This message will appear after the reset of the fixture if the yoke’s magnetic-indexing circuit malfunction (Optical Sensor or Magnetic Sensor fails) or the stepper motor is defective (or its driving IC on the main PCB). The PAN- movement is not located in the default position after the reset.

TILT- movement Er

(TILT- head movement error) This message will appear after the reset of the fixture if the head’s magnetic-indexing circuit malfunctions ((Optical Sensor or Magnetic Sensor fails)) or the stepper motor is defective (or its driving IC on the main PCB). The TILT- movement is not located in the default position after the reset.

ZOOM wheel Er

(ZOOM wheel- error) This message will appear after the reset of the fixture if the head’s magnetic-indexing circuit malfunctions (sensor failed or magnet missing) or the stepper motor is defective (or its driving IC on the main PCB). The ZOOM - wheel is not located in the default position after the reset.

PRISM wheel Er

(PRISM wheel- error) This message will appear after the reset of the fixture if the head’s magnetic-indexing circuit malfunctions (sensor failed or magnet missing) or the stepper motor is defective (or its driving IC on the main PCB). The PRISM - wheel is not located in the default position after the reset.

PRISMZ_ZOOM wheel Er

(PRISMZ_ZOOM wheel- error) This message will appear after the reset of the fixture if the head’s magnetic-indexing circuit malfunctions (sensor failed or magnet missing) or the stepper motor is defective (or its driving IC on the main PCB). The PRISM - wheel is not located in the default position after the reset.

Page 25

ARCALINE 3 User Manual XM1362-V1.0-NR

12. CLEANING AND MAINTENANCE

The following points have to be considered during inspection:

1) All screws for installing the devices or parts of the device have to be tightly connected and

must not be corroded.

2) There must not be any deformations to the housing, lenses, rigging and installation points

(ceiling, suspension, trussing).

3) Motorized parts must not show any signs of wear and must move smoothly without issue.

4) The power supply cables must not show any damage, material fatigue or sediment.

Further instructions depending on the installation location and usage have to be adhered to by a qualified installer and any safety concerns have to be removed.

In order to ensure the device remains in good condition and does not fail prematurely, we suggest regular maintenance.

1) Clean the inside and outside lens each week to avoid loss of output due to accumulation of

dust/ dirt on the lens.

2) Clean the fans each week to ensure maximum airflow and efficient thermal cooling. This will

ensure the light source is operated in the best possible condition.

3) A detailed electrical check by an approved electrician every quarter to make sure that the

circuit contacts are in good condition. This will prevent poor circuit contacts and the resultant overheating.

We recommend frequent cleaning of the device. Please use a moist, lint- free cloth. Never use alcohol or solvents.

Please refer to the instructions under “Installation instructions”.

Should you need any spare parts, please order genuine parts from your local dealer.

Remark: Errors and omissions for all information given in this manual are excepted. All information is subject to change without prior notice.