Ayre K-5Xe Owner Manual

Ayre K-5x

Owner’s Manual

A y r e

K-5x

Preamplifier

Table of

Contents

Welcome to Ayre . . . . . . . . . . . . . . . . . . . . . . . 2

Connections and Installation . . . . . . . . . . . . . . . . . . . . 3

Controls and Operation. . . . . . . . . . . . . . . . . . . . . 6

Numbers and Specifications . . . . . . . . . . . . . . . . . . 11

Statement of Warranty . . . . . . . . . . . . . . . . . . . . 12

A Place for Notes . . . . . . . . . . . . . . . . . . . . . . 15

Welcome to

Ayre

Please send in your warranty

registration card so we can

stay in contact with you.

Your Ayre K-5x offers a significant advance in the
musical performance of high-fidelity equipment.
The warmth and immediacy of a live performance
are apparent from the first listening. The
combination of superb resolution and a natural,
relaxed quality will draw you into the music, time
and time again.

This level of performance has been implemented
using the highest level of workmanship and
materials. You can be assured that the Ayre K-5x
will provide you a lifetime of musical enjoyment.

2

Connections and

Installation

The Ayre K-5x preamplifier is easy to hook up and
use. The following guidelines will ensure that the
installation goes smoothly.

Location

The infrared beam of the

remote transmitter will also

travel through glass.

When you have a choice, a
balanced connection will offer
slightly higher sound quality

than an unbalanced

connection.

A good location for your preamplifier is in an
open-backed cabinet or on a shelf. The receiver for
the infrared remote control is mounted behind the
display lens on the front panel. A direct line of sight
from the listening position will ensure the
maximum range. However, the beam will also
reflect off of most wall surfaces with a reduced
range.

Inputs

The Ayre K-5x offers two pairs of balanced inputs
and two pairs of unbalanced inputs. Balanced
connections are made via three-pin XLR connectors,
while unbalanced connections are made via RCA
connectors.

3

The FET switches used in the input selector
circuitry offer transparent, noise-free switching,
with no moving parts. Please be aware that they can
be overloaded if the output voltage from the source
component is too high.

Do not use a source component that has
an output level greater than4VRMS
unbalanced, or 8 V RMS balanced.

Using a source component with too great an output
level will cause distortion.

The input connectors on the

rear panel are labeled to

match the input selector

buttons.

If a recorder is not installed in

your system, the “Moon” input

performs exactly like the other

unbalanced inputs.

In this modern era of diverse source components, it
has become impractical to pre-label the inputs with
the actual name of the source. Instead, the K-5x has
simple icons that allow you to easily remember the
selector button associated with each source
component.

Tape Outputs

By connecting the “Tape Out” jacks on the rear of
the K-5x to a recorder with analog inputs,
recordings may be made directly from the other
source components connected to your preamplifier.
The tape outputs are switched on and off at the front
panel. Please refer to the section “Controls and
Operation” for further information.

If you are connecting a recorder to your
system, be sure to connect its outputs to
the “Moon” input of the K-5x.

4

A y r e

Boulder, Colorado USA

S.N.

K-5 Stereo Preamplifier

B1 B1

Outputs

B2 B2

The balanced outputs use

XLR connectors, while the

unbalanced outputs use RCA

connectors.

Right Channel

50/60 Hertz
10 W Max

Volts

Tape
Out

Tap e
Out

Left Channel

S2S2 S1S1

This will prevent the undesired possibility of
creating a feedback loop when making a recording.

Main Outputs

The Ayre K-5x offers one pair of balanced outputs
and one pair of unbalanced outputs. Both pairs of
outputs may be used simultaneously. However,
please note that the level of the unbalanced outputs
will be 6 dB lower than the balanced outputs.

AC Power

Outputs

The best sound quality is

normally achieved when the

K-5x is plugged directly into

the wall outlet, without using

any power strips or power line

conditioners.

Connect the Ayre K-5x to an unswitched power
source. When the unit is first connected to the AC
power, the input selector will default to “Star”, the
volume control will default to “11”, the display will
be set to “On”, and both the mute and record output
will be set to “Off”. Removing the AC power from
the unit will cause it to lose its current settings and
revert to the default settings.

5

Controls and

Operation

At the heart of the Ayre K-5x’s control system is a
sophisticated microprocessor. This microprocessor is
normally “asleep” and all digital systems are turned
off, including the master clock. When the
microprocessor receives a command, either from the
front panel or the remote control, it “wakes up” to
execute the command, and then immediately returns
to “sleep” mode. This system ensures noise-free
reproduction of music signals.

Volume Control

The volume level is changed

with the front panel knob.

The remote control may also be

used to change the volume.

6

The Ayre K-5x’s exclusive volume control yields
superlative sonic performance. Field-Effect
Transistor (FET) switches combine with discrete
metal-film resistors to create a volume control with
crystal-clear transparency and no moving parts,
along with digital accuracy and repeatability. The
volume control comprises 66 individual levels, each
with a step size of 1.0 dB allowing for precise
selection of the desired volume setting.

When the unit is first connected to an AC power
source, the volume level defaults to “11”, a relatively

A y r e

K-5x

low setting. After that, the current volume setting is
retained in memory, and will remain constant when
changing inputs.

Input Source Selection

The source component may also

be selected with the remote

control.

The input selector buttons are located below the
display. Icons that match the connector labels on the
rear panel (Star, Planet, Comet, Moon) are used to
denote the inputs. When the unit is first connected
to an AC power source, the “Star” input is selected
by default.

The input selector utilizes sophisticated FET
switches. Both the signal and ground connections to
each source component are switched, so that any
un-selected components are completely disconnected
from the system. This avoids any problems with
undesired ground loops.

7

Mute

Muting and un-muting may

also be performed with the

remote control.

The “Tape Output” function

does not operate on the “Moon”

input. This avoids the

undesired possibility of

creating a feedback loop.

The mute button provides an easy way to
temporarily turn the volume of the K-5x to “zero”.
The current volume control setting is retained in
memory and appears on the display.

Tape Output

When the “Tape Output” button is pressed, the
indicator will light up and the signal from the
currently selected source component will be routed
to the “Tape Out” connectors. This allows a
recording to be made.

Turn the “Tape Output” off, unless a recording is
being made. This will completely disconnect the
recorder from the K-5x (including the ground
connection), avoiding the possibility of undesired
ground loops.

The display function is only

available from the remote

8

control.

Display

The display of the K-5x may be turned off via the
remote control, if desired. A single blue light
indicates that the display is turned off. When
further commands are received, either from the
front-panel buttons or the remote control, the
display will be activated for a few seconds to confirm
the command, and then turn off automatically.
Pressing the “Display” button on the remote control
again will turn the display on.

Processor Pass-Through

When using the Ayre K-5x in a surround-sound
system for home theater, it is desirable to use the

“Processor Pass-Through” mode. This mode allows

your two-channel music sources to be routed
directly through the K-5x, avoiding the sonic
degradation of most processors, and at the same time
allows the front two channels of the theater system
to integrate with the K-5x with the touch of a
single button.

If you are using a surround-sound processor, connect
the front left and right outputs of the processor to
one of the inputs on the K-5x. Please note that the
K-5x can accept either balanced or unbalanced
signals.

A y r e

K-5x

To activate the “Processor Pass-Through” mode for
that input, remove the AC power from the K-5x for
at least 10 seconds. Then, while pressing the input
selector button corresponding to the chosen
surround-sound processor input, re-connect the AC
power.

9

The chosen input is now programmed for “Processor
Pass-Through” operation, disabling the now
redundant volume control of the K-5x. When that
input is selected, the preamplifier section of the
K-5x is set to unity gain (0 dB), and the volume is
controlled directly from the surround-sound
processor. The volume indicator of the K-5x will
display “PP” to show that the “Processor
Pass-Through” mode has been selected for that
input.

To clear the “Processor Pass-Through” mode from
an input and restore normal operation, remove the
AC power from the K-5x for at least 10 seconds.
Then, while pressing the “Mute” button, re-connect
the AC power.

Break-In

100 to 500 hours of music

played through the system will

ensure full break-in.

10

Due to the manufacturing processes used for the
wires and capacitors, a break-in period is necessary
for the amplifier to reach its full sonic potential.

Numbers and

Specifications

Maximum Input Level 4 V RMS – unbalanced inputs

8 V RMS – balanced inputs

Input Impedance 20 kΩ – unbalanced inputs

40 kΩ – balanced inputs (20 kΩ per phase)

XLR Input Polarity Pin 1 – Ground

Pin 2 – Non-inverting (Positive)
Pin 3 – Inverting (Negative)

Maximum Gain 4 dB – unbalanced outputs

10 dB – balanced outputs

Frequency Response DC – 200 kHz

Output Impedance 55 Ω – unbalanced outputs

110 Ω – balanced outputs (55 Ω per phase)

Power Consumption 10 watts

Dimensions 17-¼" W x 13-¾" D x 4-¾" H

44 cm x 35 cm x 12 cm

Weight 25 pounds

11.5 kg

11

Statement of

Warranty

Please take a moment to fill

out and return the enclosed

warranty registration card.

Your Ayre K-5x preamplifier is warranted against
defects in workmanship and materials for a period of
five years from the date of purchase. This warranty is
transferable to subsequent purchasers within the
original five-year period. All warranty claims must
be made through an authorized Ayre dealer or
distributor.

Warranty Statement

1. Ayre Acoustics, Inc. (Ayre) warrants the materials
and workmanship of this product for a period of five
years from date of first purchase. If any defects are
found in the materials or workmanship of this Ayre
product within the warranty period, the unit will be
repaired or replaced by Ayre or its authorized agent.

2. Purchaser must return the product, packed in the
original shipping carton, freight prepaid to:

12

Ayre Acoustics, Inc.
2300-B Central Avenue
Boulder, Colorado 80301

or to Ayre’s authorized agent.

3. Ayre reserves the right to inspect any product
that is the subject of any warranty claim prior to
repairing or replacing it. Final determination of
warranty coverage lies solely with Ayre.

Out-of-warranty claims will be billed for labor,
materials, return freight, and insurance as required.
Any product for which a warranty claim is accepted
will be returned to the purchaser and the cost of
shipping and insurance will be factory prepaid
within the boundaries of the USA. Units to be
shipped outside of the USA will be shipped freight
collect only.

4. Ayre strives to manufacture the finest possible
equipment, and therefore reserves the right to make
improvements on its products, without necessarily
assuming an obligation to retrofit such changes
upon its previously manufactured models.

5. The above warranty is the sole warranty given by
Ayre, and is in lieu of all other warranties. All
implied warranties, including warranties of
merchantability or fitness for any particular purpose
shall be strictly limited in duration to five years
from the date of original purchase, and upon
expiration of the warranty period (five years), Ayre
shall have no further obligation of any kind, whether
express or implied. Further, Ayre shall in no event
be obligated for any incidental or consequential
damages as a result of any defect or any warranty
claim, whether express or implied.

13

6. Ayre does not authorize any third party,
including any dealer or sales representative to
assume any liability of Ayre or make any warranty
for Ayre. The unit must not have been altered or
improperly serviced. The serial number on the unit
must not have been altered or removed.

7. Warranty registration cards must be completed
and mailed to Ayre within 30 days of purchase. Ayre
may, at its option, require from the purchaser valid
proof of purchase (dated copy or photocopy of
dealer's original invoice).

14

A Place for

Notes

15

16

Ayre Acoustics, Inc.

2300-B Central Avenue

Boulder, Colorado 80301

www.ayre.com

[phone]