TDC LED Derby
DMX LED Derby light effect
User manual
Any information and illustrations shown in this user manual are subject to change without further notice.
User manual version: 2.0 Creation date + author initials: 21-11-2013 RV Revision date + author initials: 16-07-2014 RV
Safety instructions
This unit must be operated by, or under the supervision of an adult. This device is not suitable for children.
Every person involved with the installation, operation and maintenance of this device has to:
- Be qualified
- Follow the instructions of this manual
- Make sure there is no damage caused by transport. If the device seems damaged from the outside, do not
use it and contact your dealer for more information and consultation.
- To make sure the device maintains in perfect condition and for safe operation, it is necessary for the user to
follow the instructions and warning notes of this user manual.
- Damage caused by improper use or modifications to the device are not covered by warranty.
- This device does not have any user-serviceable parts inside. Servicing of this device needs to be done by
qualified technicians.
Important notes regarding safety and health:
- Never let the power cord come in contact with other cables. Handle the power cord and all connectors with
the mains with caution.
- Never remove any warning or informative labels from the unit
- The ground contact always needs to be connected. Do not cover or remove the ground contact.
- Never leave cables lying around
- Do not open the device and do not modify any hard- or software of this unit.
- Do not insert this object into air vents.
- Do not connect this device to a dimmerpack.
- Do not switch the system on and off frequently as this will reduce the lifespan of the device.
- Do not drive the inputs of the fixture with a signal larger than required to work at full performance.
- Only use this device indoor, avoid contact with water, moist or other liquids. Do not place items filled with
liquids on top of the unit.
Any information and illustrations shown in this user manual are subject to change without further notice.
User manual version: 2.0 Creation date + author initials: 21-11-2013 RV Revision date + author initials: 16-07-2014 RV
WARNING!
Always keep this device away from moisture and rain! Hazardous electrical shocks may occur!
WARNING!
Only connect this device to a matching power outlet. This device is intended to work on a
specified AC currency. Connecting this device to power outlets with other voltages may result in
permanent damage and possible hazardous situations, such as fire or electrical shocks!
WARNING!
Be careful with every operation of this device. Touching live wires inside and outside the unit
may cause hazardous electrical shocks!
- Avoid nearby flames or heat sources, do not place this device near flammable liquids, gas or flammable
items.
- Always disconnect the device when it is not in use for a longer period or time, when servicing is needed or
when the device needs cleaning.
- Only handle the power cord by its connectors. Never pull the cable to remove a connector from its socket,
as this could lead to damage and electrical shocks.
- Always operate this device with a stable AC current.
- Always operate this device with the AC ground wire connected to the electrical system's ground.
- Never use other types of cables than specified in the manual, do not use defective or bad functioning
cables. Contact your dealer when the included or required cables do not work properly with this device.
- When the device has been exposed to large temperature differences (for example, transport from outdoor
to indoor), do not connect the device immediately. Do not activate the unit until it has reached room
temperature, as moist might build up inside the unit, which may cause shortcuts and/or electrical shocks.
Guidelines and types of use:
- This device is intended to be used by professionals on stage, in theaters, clubs and other equal venues.
- This device is not suitable for children and always needs to be operated by an adult.
- Only use the device when the environment is suitable and will not cause any damage. Do not use the
product in moist or dusty environments, or where long-term damage may occur such as:
- indoor swimming pools where chlorine is used.
- Beaches, where sand and salt are present.
- Outdoor, without roof protection
- Indoor areas where intense heat sources are present or where the temperature exceeds levels
which are comfortable for humans.
- Only use the included power adapter and only connect the device to a suitable power outlet with the correct
output voltage. Connecting the device to a power outlet with the wrong type of voltage or using the product
with a wrong type of power supply may cause permanent damage to the device.
- Avoid shocks and collision during use and transport. Do not transport the device while in use. Avoid brute
force during the installation and operation of this device.
- Familiarize yourself with the functions of the device before use. Do not allow operation of the device by
unskilled or unqualified people.
- Use of the device in other ways than described in this user manual may cause damage and injury. Ayra can
not be held responsible for any damage or injury caused by improper use.
Storage and transport:
- This device is intended for mobile use. When transported, use the original packaging of the product, or a
fitting flightcase, preferably filled with foam.
- This device is not intended for permanent use. Operation breaks will ensure that the lifespan of the device
remains unchanged.
- If the device is not used for a longer period of time, disconnect it from its power source and store it in its
original packaging, or in a fitting flightcase.
- Store the device indoor, dry and do not expose the device to extreme temperature differences.
Housing:
- Inspect the housing of the device frequently. Severe dents, cracks and missing screws should be avoided
at all costs. Do not use the device when the housing is not in optimal condition. Contact your dealer or a
skilled technician when in doubt about the state of the device
- Check the fixture and screws for corrosion. Corrosion should not be present on the fixture. Contact your
dealer or a skilled technician when corrosion is found on the fixture
- Every power or signal chassis/connector should be mounted tightly. Do not use the device when connectors
are loose.
- Do not use the power cord when the cores are visible. Contact your dealer for a replacement if needed.
- Avoid the buildup of dust and dirt. Clean the exterior of the fixture every month with a dry or damp cloth.
When using the device intensively, the cleaning frequency needs to be increased.
Fuses:
- The main fuse of this device is to be found on the rear of the device. In most cases, directly next to the
power inlet.
- Only replace a fuse for a new one with the same type and rating! Do not use a fuse with a higher or lower
Any information and illustrations shown in this user manual are subject to change without further notice.
User manual version: 2.0 Creation date + author initials: 21-11-2013 RV Revision date + author initials: 16-07-2014 RV
rating.
- Do not bridge the fuse with electrical wires, aluminum foil, as the fuse is used for protection against
electrical shocks and short circuit.
- Always mount the fuse cover back to the fuse compartment.
Any information and illustrations shown in this user manual are subject to change without further notice.
User manual version: 2.0 Creation date + author initials: 21-11-2013 RV Revision date + author initials: 16-07-2014 RV
Box contents
Box contents
1x TDC LED Derby fixture
1x power cable to Schuko
1x power cable to UK plug
Unit and accessory inspection
- Always use the supplied power cable to connect the unit to a power supply. If the cable appears broken or
has visible damage, do not use it.
- If the unit is not going to be used for a longer period of time, disconnect it from the power supply and store it
in a dust-free environment.
- Always check the unit for possible damage before use. If you suspect that something is wrong with the unit,
do not connect it to a power source! When you suspect that your unit is broken or damaged, contact your
local dealer or a certified technician to inspect the unit.
Any information and illustrations shown in this user manual are subject to change without further notice.
User manual version: 2.0 Creation date + author initials: 21-11-2013 RV Revision date + author initials: 16-07-2014 RV
Device overview
1. Beam output
2. Adjustable bracket
3. Safety eye
4. Menu display with buttons
5. IEC Power outlet (Power link)
6, IEC Power inlet with fuse
7. Built-in microphone
8. DMX input (3P XLR)
9. DMX output (3P XLR)
Any information and illustrations shown in this user manual are subject to change without further notice.
User manual version: 2.0 Creation date + author initials: 21-11-2013 RV Revision date + author initials: 16-07-2014 RV
1
2
3
4
5
6
7
8
9
Setting up the unit
To activate the unit, connect the included power supply to the unit and a suitable 230V, 50 Hz power outlet.
The fixture will start up and show the last chosen setting on the display. Usually, with a new product, this is
the DMX mode with the value set on 001.
The display shows several settings, each with the possibility to set several values.
Use the display and the menu buttons to set preferences, change settings and scroll through the menu.
“Enter” is used to save a certain setting or preset, press “Menu” for at least 2 seconds to discard the change
and return to the main menu.
The table below shows an explanation for every feature and value.
display Mode Function
ADDR DMX address setting A001-A512
SLND Master/slave mode Master (default)
Slave 1 - Slave 2
SHND Auto mode Auto Speed 1-9
SOUN Sound controlled mode Sound controlled mode on/off
SENE Sound sensitivity Sound sensitivity 0-100
BLND Black out mode LED mode, YES- NO
DISP Display inversion Display Inversion, Idsp-dspI
TEST Test mode Self test
Hour Using time of light Fixture hours,0 ~ 9999
UERS Firmware version Firmware version xxx
ADDR: DMX address setting, used to determine the DMX starting channel. From this channel on, the fixture
will respond to values, corresponding with the amount of channels that the fixture is occupying. (For
example, when you turn the fixture in 3CH mode and set the starting address to value 003, the fixture will
respond to channels 3, 4 and 5.)
SLND: When using the master/slave function, you need to connect 2 or more fixtures with XLR-XLR cable.
The first fixture in line needs to be set as master, the others as Slave 1 or 2 (synchronized or mirrored
performance). This way, the slaves will mimic the behavior of the master fixture for wonderful synchronized
lighting shows.
SHND: Automatic mode, runs internal programs on a selectable speed.
SOUN: Activate or disable the built-in sound controlled mode. This way, the fixture will respond to the beat of
the music.
SENE: The sensitivity of the built-in microphone is adjustable, to optimize the built-in sound controlled mode.
For example, when your music source (speakers) are placed far away, you might want to increase the
sensitivity to make sure that the fixture responds to the sound accurately.
BLND: Black out mode (S.L.S.) The Signal Loss Setting provides the right action when the fixture suddenly
loses DMX signal. By activating the function, the fixture goes in blackout mode. By deactivation the mode,
the fixture goes in sound controlled mode.
DISP: Display invert version – When using the fixture in a hanging setup, it is possible to flip the display, so
the characters will be shown upside down. This makes reading the several statuses much easier.
TEST: Self test mode, to control all segments and LEDs
Any information and illustrations shown in this user manual are subject to change without further notice.
User manual version: 2.0 Creation date + author initials: 21-11-2013 RV Revision date + author initials: 16-07-2014 RV
Hour: The fixture shows how much hours it has been active. This is very practical for rental companies
which need to perform service intervals on all fixtures after several hours of performing, to maintain optimal
shape.
UERS: Displays the software version which is installed on the main PCB.
The TDC LED Derby is equipped with several working modes, each with its own advantages. For simple
events there are stand-alone modes, for advanced situations there are options to create synchronized
lightshows, or controlled with a DMX-512 controller. A short description for each mode can be found below:
Auto:
Automatic lightshow with a pre-programmed internal show, on a pre-defined speed.
Sound:
Automatic lightshow with a pre-programmed internal show, on the beat of the music, thanks to an internal
microphone which senses the beat of the music and will change a step every time a beat is detected.
Slave:
In master/slave mode, it is possible to link several TDC LED Derby fixtures together, to create synchronized
lightshows in the Auto or Sound mode. The first fixture in the chain needs to be set in the Auto or Music
mode. All the next fixtures need to be set to Slave and will mimic the behavior of the first fixture. The
master/slave function requires XLR – XLR cables (not included).
DMX:
The TDC LED Derby can be connected to a DMX-controller with standard XLR – XLR cable. While doing so,
a DMX-terminator must be connected to the last fixture, at the end of the DMX-chain. This prevents
reflections in the DMX-signal, which could cause flickering and unwanted behavior from your intelligent
fixtures.
A DMX terminator is a XLR connector with a resistor of 120 Ohm, placed between pin 2 and 3 as a bridge.
With the following channel assignment, it is possible to control the TDC LED Derby:
5-ch
Mode
Function Value
1 Function
000-007
008-190
191-200
201-247
248-255
Dimmer 0
Dimmer 1-100%
Dimmer 100%
Strobe slow to fast
Stand alone
2 Red
000-255
0-100%
3 Green
000-255
0-100%
4 Blue
000-255
0-100%
5 Motor
000-255
0°~ 360°
Any information and illustrations shown in this user manual are subject to change without further notice.
User manual version: 2.0 Creation date + author initials: 21-11-2013 RV Revision date + author initials: 16-07-2014 RV
Installation and maintenance
Installing the fixture in a hanging position
When installing the system in a hanging position (for example, on a truss construction), nstall proper Gclamps or half couplers (not included).
NOTE: When installing the system in a hanging position, the following list of safety precautions must be met:
- Use at least one regular clamp, for optimal stability and safety.
- Use at least one safety cable, capable of holding 3x the weight of the system. Safety cables must be
installed in such a way that it is impossible for the system to fall down when one of the two mounting points
breaks.
- It is prohibited to install the system by using only safety cables or chains!
Warranty is void when any of the above safety precautions are not met. Ayra can not be held responsible if
any damage or injury occurs due to improper use of the system.
Transport
When using this fixture in mobile setups, provide sufficient protection during transport. Always use the
provided transport box or a protecting flightcase to protect the system.
Replacing the internal fuses
First check whether a failing power supply may be the cause of malfunction. When you suspect that one of
the internal fuses is broken, the fuse can be replaced by removing the fuse cover, located on the rear of the
fixture, near the power inputs, outputs and control menu.
WARNING: Before checking the fuse, always disconnect the fixture from your wall outlet or any other power
supply to prevent electric shocks.
Always replace a broken fuse with a fuse that has the same type and rating. After the fuse has been
replaced, always close the fuse-cover. Reconnect the fixture to your power supply and check whether the
problem is solved. When this does not solve your problem, contact your local dealer for help.
Spare parts
This unit has no user serviceable parts inside. When any damage to internal components occurs, contact
your local dealer or a specialized technician in order to repair the fixture.
Cleaning:
Clean the housing of the fixture frequently with a damp cloth, to remove dust and/or dirt.
WARNING: Always disconnect the fixture from your wall outlet or other power supply and let the fixture dry
before reconnecting it. This prevents possible electrical shocks.
The lenses can be cleaned with a non-aggressive glass cleaning solution, but is not recommended. Ayra
recommends to clean the mirror and lens with a fine brush, while removing dust and/or dirt with a vacuum
cleaner. Avoid touching the lenses with your bare fingers, to prevent fingerprints on the optics.
Checkup
To prevent dangerous situations, make sure your fixture is in optimal condition before using it. Check your
fixture frequently by using the following checklist:
- All screws must be mounted tightly.
- Check all screws and metal parts for corrosion. No visible corrosion may be present.
- The exterior of your fixture must be in optimal condition. Check your fixture for dents, cracks or missing
parts.
- Your installation spot must be in optimal condition. Check your installation spot for corrosion, cracks, dents
and strength.
- Electrical components (connectors and cables) must be in optimal condition. Any form of damage (cuts,
exposed wire cores or any other visual deformities should not be present.
If any visual or mechanical damage is detected, contact your local dealer or a specialized technician. Do not
use a damaged or failing fixture.
Any information and illustrations shown in this user manual are subject to change without further notice.
User manual version: 2.0 Creation date + author initials: 21-11-2013 RV Revision date + author initials: 16-07-2014 RV
DMX lighting troubleshooting
If you have any problems with DMX lighting, consult this troubleshooting section to solve any difficulties with
your product. If this troubleshooting section does not solve your problem, contact your dealer for more
information and help.
This troubleshooting section contains the most frequent problems and is not a complete collection of possible
faults, defects and solutions. The troubleshooting section applies for DMX controllers, DMX cabling and DMX
lighting fixtures. It is possible that not all described problems, causes and solutions apply to your situation as
product details may vary from product to product.
Problem Possible Cause Solution
The fixture can not be activated Blown fuse Check the fuse compartiment for
blown fuses and replace it if
necessary.
No power cable plugged in Plug in the power supply to a
matching power outlet
Power switch is not in the ON
position
Turn on the device by switching
the ON/OFF switch to the ON
position, if available
The fixture does not respond to
DMX signals
Wrong DMX address Set the DMX address to the right
value
DMX controller blackout function
activated
Deactivate the blackout function of
your DMX controller
Faulty positioning of the DMX
polarity switch on the controller
flip the polarity switch on your
DMX controller
No response or DMX activity
signal LEDs active
Check your DMX cables for
possible connection breaks and
replace them if necessary.
The fixture does not respond to
sound
Wrong working mode selected. Check if the sound activated mode
of the fixture is activated.
Microphone sensitivity level is set
too low
Increase the microphone
sensitivity of the built-in
microphone
Speaker placed too far away or
lack of bass
Place your lighting effect closer to
your speakers (or vice versa)
and/or increase low frequency
volumes. The microphone will not
be triggered with high pitched
sounds.
The beam output is very low Dirty/dusty optics Clean the lens and/or other optics
with a dry or damp cloth
Dimmer is not set to full output Set all dimmer levels to 100% on
your DMX console
Sometimes the DMX signal is lost
and/or some fixtures are
flickering / behaving odd
sometimes
Faulty/broken DMX cables Check your DMX cables for
possible connection breaks and
replace them if necessary.
Power cable interference on your Avoid installing the DMX and
Any information and illustrations shown in this user manual are subject to change without further notice.
User manual version: 2.0 Creation date + author initials: 21-11-2013 RV Revision date + author initials: 16-07-2014 RV
DMX signal (high) power cables parallel to
each other.
No DMX terminator Apply a DMX terminator at the end
of your DMX-chain
Signal loss or distortion in DMX
values
Apply a DMX booster in your DMX
chain after 32 fixtures or less. After
a maximum of 32 fixtures the DMX
signal needs to be refreshed.
Moving parts are not functioning
well, values do not match and/or
rattling sounds are noticed
Faulty stepping motor positioning Possible value loss of stepping
motors. Activate the reset function,
or unplug the power supply and
plug it back in to activate the reset
program. This will reset all values
to the original 0-point.
The fixture does not respond fast
enough to the set speed on my
DMX controller
Moving parts can not keep up with
the set speed
Decrease the chase speed of your
DMX controller, as the stepping
motors of your fixture need some
time to move from one point to
another.
The fixture does not respond to all
DMX-channels
Wrong DMX channel mode Check the DMX channel mode of
the fixture. If the wrong value is
set, change the channel mode to a
different setting and try again.
Any information and illustrations shown in this user manual are subject to change without further notice.
User manual version: 2.0 Creation date + author initials: 21-11-2013 RV Revision date + author initials: 16-07-2014 RV
Technical specifications
- Powerful LED derby effect
- High output thanks to 9W RGB LED chip
- Dozens of narrow, colourful and moving beams fill the room with light
- Razorsharp optics for intense beam projections
- Individual LED chip control with colour mixing, for creative colour combinations.
- Working modes: Automatic, music-controlled, master/slave, DMX
- Exciting built-in programs or full control with a DMX controller
- DMX operation: 5 channels
- Adjustable microphone sensitivity for music-controlled mode
- Menu display and buttons for easy adjustment of settings
- Low power consumption – High output – Long lifespan
Power:
- Voltage: AC100-240V 50Hz/60Hz
- Power: 20W
Physical:
- Dimensions: 325 x 270 x 240 mm (with folded bracket)
- Weight: 4 kg
Connectors:
- DMX: 3p XLR male and female
- Power: IEC Power input with fuse, Power Link output
Included accessories:
- Power cable IEC to Schuko
- Power cable IEC to UK plug
Connectors and wiring schematics:
DMX-connections: Electrical wiring:
Any information and illustrations shown in this user manual are subject to change without further notice.
User manual version: 2.0 Creation date + author initials: 21-11-2013 RV Revision date + author initials: 16-07-2014 RV
Loading...