INSTALLATION INSTRUCTIONS FOR PART TRIGGER
The Trigger is a universal module that provides 15
different preset functions that are activated from a
positive or negative trigger. In addition to the preset
features, the Trigger has 8 custom modes with
customizable settings that allows the installer to
utilize their imagination.
TRIGGER
Cutting Tool • Tape • Crimping Tool
Connectors (ie. butt connectors, bell caps, etc.)
IGNITIO
N
TERMINALS
WIRE
CUTTER
M3.5
M
2.6
M
3
M
5
M
4
I
S
O
6
2.5
1.5
TOOLS REQUIRED FOR INSTALLATION
Pin 1: Black (Chassis Ground)
Pin 2: Purple (Conguration input)
Pin 3: White (Conguration input)
Pin 4: Pink (Conguration input)
Pin 5: Orange (Conguration input)
Pin 6: Green ((-) Output 500mA Max)
Pin 7: Red ((-) Output 500mA Max)
Pin 8: Blue ((+) output 2 amp Max)
Pin 9: Brown (+ 0.8- 16v input trigger)
Pin 10: Gray (- input trigger)
Pin 11: Yellow (12 volt Constant/Switched)
TRIGGER
Notes:
*Pin 1 needs to be attached to ground and pin 11 needs to be attached to 12 volt
constant on all congurations listed below.
* Metra recommends using a single pulse double throw relay in every application.
(Metra part # E-123)
Pin diagram
Mode 1: Retained accessory power
Description: Device will turn on when accessory turns on, and will not turn off
until door opens or 10 minutes passes, whichever comes rst.
Connections:
Interface wiring To
Pin 2 (Purple) Ground
Pin 8 (Blue) Retained accessory output (2 amp max)
Pin 9 (Brown) Vehicles accessory or ignition
Pin 10 (Gray) Negative door trigger
Descriptions of modes and wiring instructions.
Default: EBrake Emulator
Description: Emulates an EBrake signal for use in RV’s, off road vehicles,
and exhibition vehicles.
Connections:
Interface wiring To
Pin 6 (Green) Aftermarket radios parking brake input
Pin 7 (Red) Aftermarket radios parking brake intput
Pin 8 (Blue) Foot brake of radio
Pin 9 (Brown) Vehicles accessory or ignition
Mode 2: Delayed turn-on
Description: When the input is activated, there will be a 2-second delay
before pin 8 turn-on.
Connections:
Interface wiring To
Pin 3 (White) Ground
Pin 6 (Green) Negative delay turn-on output (500 mA max)
Pin 7 (Red) Negative delay turn-on output (500mA max)
Pin 8 (Blue) Positive delay turn-on output (2 amp max)
Pin 9 (Brown) 12 volt output
Mode 3: Low voltage turn-on
Description: Provides 12 volts turn on from a low voltage source
Connections:
Interface wiring To
Pin 2 (Purple) Ground
Pin 3 (White) Ground
Pin 8 (Blue) 12 volt output (2 amp max)
Pin 9 (Brown) Low voltage input
Mode 4: Latched outputs
Description: Allow the capability of making a pulsed signal a latched signal.
Connections:
Interface wiring To
Pin 4 (Pink) Ground
Pin 6 (Green) Negative latched output (500 mA max)
Pin 7 (Red) Negative latched output (500 mA max)
Pin 8 (Blue) Positive latched output (2 amp max)
Pin 9 (Brown) Positive pulsed input (use only one)
Pin 10 (Gray) Negative pulsed input (use only one)
Mode 5: GMLAN aftermarket amp turn-on
Description: Provides an amp turn on LAN vehicles for adding an
aftermarket amp.
Connections:
Interface wiring To
Pin 2 (Purple) Ground
Pin 4 (Pink) Ground
Pin 8 (Blue) Aftermarket ampli ers turn on.(2 amp max)
Pin 9 (Brown) Remote turn on from vehicle (see attached diagram)
Pin 10 (Gray) Vehicle mute (see attached diagram)
Vehicle Vehicle Connect
connector PIN to
number number Trigger
1 1 Pin 11 (Yellow)
1 8 Pin 1 (Black)
1 6 Pin 9 (Brown)
2 8 Pin 10 (Gray)
Connector 1 Connector 2
7 8
1
1
8
9
14 16
Mode 6: Active edge pulse generator
Description: Allow the capability of making an input signal a pulse signal.
Connections:
Interface wiring To
Pin 4 (Pink) Ground
Pin 6 (Green) Negative pulsed output (500 mA max)
Pin 7 (Red) Negative pulsed output (500 mA max)
Pin 8 (Blue) Positive pulsed output (2 amp max)
Pin 9 (Brown) Positive input (use only one)
Pin 10 (Gray) Negative input (use only one)
Mode 7: Turn-off delay
Description: When the output is turned off, the pin 8 will stay active for two
additional seconds.
Connections:
Interface wiring To
Pin 2 (Purple) Ground
Pin 3 (White) Ground
Pin 4 (Pink) Ground
Pin 6 (Green) Negative delay turn-off output (500 mA max)
Pin 7 (Red) Negative delay turn-off output (500mA max)
Pin 8 (Blue) Positive delay turn-off output (2 amp max)
Pin 9 (Brown) 12 volt output
Mode 8: Double pulse latch
Description: Creates a latched signal from a double pulse signal.
Connections:
Interface wiring To
Pin 5 (Orange) Ground
Pin 6 (Green) Negative latched output (500 mA max)
Pin 7 (Red) Negative latched output (500 mA max)
Pin 8 (Blue) Positive latched output (2 amp max)
Pin 9 (Brown) Positive double pulse input (use only one)
Pin 10 (Gray) Negative double pulse input (use only one)
Mode 9: Double pulse to one-second output
Description: Converts a double pulse output to a single pulse output
Connections:
Interface wiring To
Pin 2 (Purple) Ground
Pin 5 (Orange) Ground
Pin 6 (Green) Negative single pulse output (500 mA max)
Pin 7 (Red) Negative single pulse output (500 mA max)
Pin 8 (Blue) Positive single pulse output (2 amp max)
Pin 9 (Brown) Positive double pulse input (use only one)
Pin 10 (Gray) Negative double pulse input (use only one)
Mode 10: Theft detection/closed loop trigger
Description: When connected, if item loses ground the Trigger will send out a
12 volt constant signal which can be hooked to an audible device.
Connections:
Interface wiring To
Pin 3 (White) Ground
Pin 5 (Orange) Ground
Pin 8 (Blue) Positive of siren (not included)(2 amp max)
Pin 10 (Brown) Items ground point.
Mode 11: Channel expander
Description: Gives the ability to add additional channels to an alarm, etc…
Connections:
Interface wiring To
Pin 2 (Purple) Ground
Pin 3 (White) Ground
Pin 5 (Orange) Ground
Pin 6 (Green) Negative latched output (500 mA max) (2 pulses to activate)
Pin 7 (Red) Negative latched output (500 mA max) (1 pulse to activate)
Pin 8 (Blue) Positive latched output (2 amp max) (3 pulses to activate)
Pin 9 (Brown) Positive pulse input (use only one)
Pin 10 (Gray) Negative pulse input (use only one)
Mode 12: Simple data detector (amp turn on signal from data)
Description: Produces a positive or negative signal out when data is detected.
Note: Output will stay on 3 seconds after data stops transmitting.
Connections:
Interface wiring To
Pin 3 (White) Ground
Pin 4 (Pink) Ground
Pin 6 (Green) Negative output (500 mA max)
Pin 7 (Red) Negative output (500 mA max)
Pin 8 (Blue) Positive output (2 amp max)
Pin 9 (Brown) Vehicles data line (see attached diagrams)
Mode 13: Long delayed turn-off (for headlights)
Description:
This mode will keep headlights on for 1 minute after ignition is turned off.
Connections:
Interface wiring To
Pin 2 (Purple) Ground
Pin 4 (Pink) Ground
Pin 5 (Orange) Ground
Pin 6 (Green) Negative 1 minute output (500 mA max)
Pin 7 (Red) Negative 1 minute output (500 mA max)
Pin 8 (Blue) Positive 1 minute output (2 amp max)
Pin 10 (Gray) Headlight switch (negative signal)
Mode 14: Dome light delay
Description: Keeps dome light on for 30 seconds after ignition is turned off
Connections:
Interface wiring To
Pin 3 (White) Ground
Pin 4 (Pink) Ground
Pin 5 (Orange) Ground
Pin 6 (Green) Negative 30 second output (500 mA max)
Pin 7 (Red) Negative 30 second output (500 mA max)
Pin 8 (Blue) Positive 30 second output (2 amp max)
Pin 10 (Gray) Accessory or ignition from vehicle
Mode 15: Custom program
Description: Ability to custom program the Trigger using the Trigger program.
Custom Program Modes:
Custom Mode 1: Channel expander, latched
Description: Measures pulses that occur during 5 second interval. One pulse
per 5 seconds will toggle PIN 6 (GREEN), two pulses per 5 seconds will toggle
PIN 7 (RED), and three pulses per 5 seconds will toggle PIN 8 (BLUE).
Connections:
Interface wiring To
Pin 2 (Purple) Ground
Pin 3 (White) Ground
Pin 4 (Pink) Ground
Pin 5 (Orange) Ground
Pin 6 (Green) Negative latched output (500 mA max) (2 pulses to activate)
Pin 7 (Red) Negative latched output (500 mA max) (1 pulse to activate)
Pin 8 (Blue) Positive latched output (2 amp max) (3 pulses to activate)
Pin 9 (Brown) Positive pulse input (use only one)
Pin 10 (Gray) Negative pulse input (use only one)
Custom Mode 2: Channel expander, pulsed
Description: Measures pulses that occur during 5 second interval. One pulse
per 5 seconds will drive PIN 6 (GREEN) active for XX seconds, two pulses per
5 seconds will drive PIN 7 (RED) active for XX seconds, and three pulses per 5
seconds will drive PIN 8 (BLUE) active for XX seconds. XX is denable between
.1 and 300 seconds.
Connections:
Interface wiring To
Pin 2 (Purple) Ground
Pin 3 (White) Ground
Pin 4 (Pink) Ground
Pin 5 (Orange) Ground
Pin 6 (Green) Negative pulsed output (500 mA max) (2 pulses to activate)
Pin 7 (Red) Negative pulsed output (500 mA max) (1 pulse to activate)
Pin 8 (Blue) Positive pulsed output (2 amp max) (3 pulses to activate)
Pin 9 (Brown) Positive pulse input (use only one)
Pin 10 (Gray) Negative pulse input (use only one)
Custom Mode 3: Delayed turn-off
Connect active high input to pin 9, or active low input to pin 10. Use any output
pin. When input goes high, output will turn on immediately. When input goes
inactive, output turn-off will be delayed by XX seconds, where XX is denable
between .1 and 300 seconds.
Connections:
Interface wiring To
Pin 2 (Purple) Ground
Pin 3 (White) Ground
Pin 4 (Pink) Ground
Pin 5 (Orange) Ground
Pin 6 (Green) Negative latched output (500 mA max)
Pin 7 (Red) Negative latched output (500 mA max)
Pin 8 (Blue) Positive latched output (2 amp max)
Pin 9 (Brown) Positive pulse input (use only one)
Pin 10 (Gray) Negative pulse input (use only one)
Custom Mode 4: Delayed turn-on
Description: Connect active high input to pin 9, or active low input to pin 10.
Use any output pin. When input goes high, output will turn on after a delay of XX
seconds. When input goes inactive, output turn-off will be immediate.
XX is denable between .1 and 300 seconds.
Connections:
Interface wiring To
Pin 2 (Purple) Ground
Pin 3 (White) Ground
Pin 4 (Pink) Ground
Pin 5 (Orange) Ground
Pin 6 (Green) Negative latched output (500 mA max)
Pin 7 (Red) Negative latched output (500 mA max)
Pin 8 (Blue) Positive latched output (2 amp max)
Pin 9 (Brown) Positive input (use only one)
Custom Mode 5: Generic three-output delay/pulse width,
edge driven (for use with linear actuators)
Description: When either input goes active, each output will go active after a
delay, and then stay active for a pulse width. Each output has an independent
delay and pulse width, denable between .1 and 300 seconds.
Connections:
Interface wiring To
Pin 2 (Purple) Ground
Pin 3 (White) Ground
Pin 4 (Pink) Ground
Pin 5 (Orange) Ground
Pin 6 (Green) Negative output (500 mA max)
Pin 7 (Red) Negative output (500 mA max)
Pin 8 (Blue) Positive output (2 amp max)
Pin 9 (Brown) Positive pulse input (use only one)
Pin 10 (Gray) Negative pulse input (use only one)
Custom Mode 6: Generic three-output delay/pulse width,
level driven (validity)
Description: When either input goes active, each output will go active after a
delay, and then stay active for a pulse width. Each output has an independent
delay and pulse width, denable between .1 and 300 seconds.
Connections:
Interface wiring To
Pin 2 (Purple) Ground
Pin 3 (White) Ground
Pin 4 (Pink) Ground
Pin 5 (Orange) Ground
Pin 6 (Green) Negative output (500 mA max)
Pin 7 (Red) Negative output (500 mA max)
Pin 8 (Blue) Positive output (2 amp max)
Pin 9 (Brown) Positive pulse input (use only one)
Pin 10 (Gray) Negative pulse input (use only one)
Custom Mode 7: Square wave-generator
(sounds horns and blinks lights)
Description: When either input goes active, all three outputs will toggle every
XX seconds, where XX is denable between .1 and 300 seconds. Stops when
input goes inactive.
Connections:
Interface wiring To
Pin 2 (Purple) Ground
Pin 3 (White) Ground
Pin 4 (Pink) Ground
Pin 5 (Orange) Ground
Pin 6 (Green) Negative output (500 mA max)
Pin 7 (Red) Negative output (500 mA max)
Pin 8 (Blue) Positive output (2 amp max)
Pin 9 (Brown) Positive latched input (use only one)
Pin 10 (Gray) Negative latched input (use only one)
Custom Mode 8: Multiple pulse generator
Description: A single input pulse on either input will produce multiple pulses on
all outputs. The number of pulses can vary from 1 to 255, and each pulse will last
XX seconds, where XX is denable between .1 and 300 seconds.
Connections:
Interface wiring To
Pin 2 (Purple) Ground
Pin 3 (White) Ground
Pin 4 (Pink) Ground
Pin 5 (Orange) Ground
Pin 6 (Green)
Multiple Negative pulsed output (500 mA max) (2 pulses to activate)
Pin 7 (Red)
Multiple Negative pulsed output (500 mA max) (1 pulse to activate)
Pin 8 (Blue)
Multiple Positive pulsed output (2 amp max) (3 pulses to activate)
Pin 9 (Brown)
Positive pulse input (use only one)
Pin 10 (Gray)
Negative pulse input (use only one)
AXXESS ACCESSORIES
STEREOS
Loading...