Axxess MITO-03 Installation Instructions Manual

MIT O-03

INSTALLATION INSTRUCTIONS

Mitsubishi Amplifier Interface
2014-2019

INTERFACE FEATURES

• Pre-wired ASWC-1 harness (ASWC-1 sold separately)

• Designed for amplified models

• Retains balance and fade

• Micro-B USB updatable

INTERFACE COMPONENTS

• MITO-03 interface

• MITO-03 harness

• 16-pin harness

APPLICATIONS

Mitsubishi

Lancer 2014-2017
Outlander 2014-2019

AxxessInterfaces.com © COPYRIGHT 2019 METRA ELECTRONICS CORPORATION REV. 9/25/19 INSTMITO-03

TABLE OF CONTENTS

Connections ............................................................2

Installation .............................................................3

Programming .........................................................3

Adjustments ........................................................... 3

TOOLS & INSTALLATION ACCESSORIES REQUIRED

• Crimping tool and connectors, or solder gun,
solder, and heat shrink • Tape • Wire cutter

• Zip ties

Product Info

CONNECTIONS

From the 16-pin harness to the aftermarket radio:

• Connect the Blue/White wire to the amp turn on wire.

• Connect the White wire to the left front positive speaker output.

• Connect the White/Black wire to the left front negative speaker output.

• Connect the Gray wire to the right front positive speaker output.

• Connect the Gray/Black wire to the right front negative speaker output.

• Connect the Green wire to the left rear positive speaker output.

• Connect the Green/Black wire to the left rear negative speaker output.

• Connect the Purple wire to the right rear positive speaker output.

• Connect the Purple/Black wire to the right rear negative speaker output.

• Tape off and disregard the following (6) wires , they will not be used in this application:

Blue/Pink, Brown, Green/Purple, Light Green, Orange/White, Red

From the MITO-03 harness to the aftermarket radio:

• Connect the Black wire to the ground wire.

• Connect the Yellow wire to the battery wire.

• Connect the Red wire to the accessory wire.

• Connect the Orange wire to the Illumination wire (If applicable).

12-pin pre-wired ASWC-1 harness & 3.5mm jack:

•

This harness and 3.5mm jack is to be used along with the optional ASWC-1 (sold separately) to
retain steering wheel audio controls. If the ASWC-1 is not being used, disregard this harness. If
it will be used, refer to the vehicle specific ASWC-1 instruction from Axxess Interfaces for radio
connections and programming. Disregard the harness that comes with the ASWC-1.

2

IN S TALL AT I ON PROGRAMMING

Attention! The factory satellite radio and Bluetooth modules must be disconnected from the
vehicle. Failure to perform these steps will cause the factory amplifier to not play properly.

1. Find and disconnect the factory satellite radio module.

• The satellite module for the Lancer and Outlander can be located high in the passenger
side kick panel.

2. Find and disconnect the factory Bluetooth module.

• The Bluetooth module for the Lancer can be located behind the glove box, up high.

• The Bluetooth module for the Outlander can be located below the factory radio.

3. Connect the MITO-03 harness to the MITO-03 interface, and then to the wiring harness in

the vehicle.

4. If an ASWC-1 (sold separately) will be used, do not connect it until the MITO-03 is

programmed and fully functional.

Attention! If the interface loses power for any reason, the following steps will need to be
performed again.

•

Turn the key (or push-to-start button) to the ignition position and wait until the radio comes on.

Note: If the radio doesn’t come on within 60 seconds, turn the key to the off position,

disconnect the interface, check all connections, reconnect the interface, then try again.

• Turn the key to the off position, then to the accessory position. Test all functions of the
installation for proper operation, before reassembling the dash.

ADJUSTMENTS

Audio Level Adjustment

1. Locate the potentiometer on the interface by the 16-pin harness.

2. Turn the volume of the radio up 3/4 of the way.

3. With a small flat-blade screwdriver, adjust the potentiometer clockwise to raise the audio

level; counterclockwise to lower.

4. Once at a desired level, audio level adjustment is complete.

REV. 9/25/2019 INSTMITO-03

3