Axxess AX-LR902 Installation Instructions Manual

Page 1

CAUTION!

All accessories, switches, climate controls panels, and especially air bag indicator lights must be connected before cycling the ignition. Also, do not remove the factory radio with the key in the on position, or while the vehicle is running.

AX-LR902

INSTALLATION INSTRUCTIONS

INTERFACE FEATURES

INTERFACE COMPONENTS

TOOLS REQUIRED

• Wire cutter • Crimp tool • Solder gun • Tape

• Connectors (example: butt-connectors, bell caps, etc.) • Zip ties

TABLE OF CONTENTS

Connections to be made ....................................2-3

Installing the AX-LR902 interface .........................3

Programming the ASWC-1 interface ................. 3-4

Screen operation ................................................4-6

Land Rover Range Rover Evoque Data Interface with SWC & Factory Display Retention 2014*

• Provides accessory power

• Designed for non-ampliﬁed models

• Provides NAV outputs (parking brake, reverse, speed sense)

• Retains audio controls on the steering wheel

• Retains parking sensor chimes

• Retains balance and fade

• Retains factory features: date, time

• Retains most of the vehicle settings that was displayed on the factory radio *

• Micro “B” USB updatable

* Attention!

The aftermarket radios backup camera input will be used to display the vehicle settings. If the radio doesn’t have a backup camera

Input, then there will be no visualization of the vehicle settings. An externally mounted screen could be substituted in this situation.

• AX-LR902 interface

• ASWC-1 interface

• AX-LR902 harness

• ASWC-1 harness

• Female 3.5mm connector with stripped leads

• Chime speaker

* For models with rear parking sensors

Page 2

CONNECTIONS TO BE MADE

From the aftermarket radio to the AX-LR902 harness:

• Connect the Black wire to the ground wire.

• Connect the Yellow wire to the battery wire.

• Connect the Red wire to the accessory wire.

• If the aftermarket radio has an illumination wire, connect the Orange wire to it.

• Connect the Brown wire to the mute wire.

• Connect the White wire to the left front positive speaker.

• Connect the White/Black wire to the left front negative speaker.

• Connect the Gray wire to the right front positive speaker.

• Connect the Gray/Black wire to the right front negative speaker.

• Connect the Green wire to the radio’s left rear positive speaker.

• Connect the Green/Black wire to the radio’s left rear negative speaker.

• Connect the Purple wire to the radio’s right rear positive speaker.

• Connect the Purple/Black wire to the radio’s right rear negative speaker.

The following (3) wires are only for multimedia/navigation radios that require these wires.

• Connect the Blue/Pink wire to the VSS/speed sense wire.

• Connect the Green/Purple wire to the reverse wire.

• Connect the Light Green wire to the parking brake wire.

• The 6-pin harness labeled “To Parking Switch Optional” will connect to the parking brake switch harness from the 95-9403B dash kit (sold separately).

From the aftermarket radio to the ASWC-1 harness:

This harness is only to be used if the vehicle is equipped with steering wheel controls or a backup camera

• Connect the Red wire to the accessory wire.

• For the radios listed below, connect the

female 3.5mm connector with stripped leads

, to the

male 3.5mm SWC jack from the ASWC-1 harness. Any remaining wires tape off and disregard:

• Eclipse: Connect the steering wheel control wire, normally Brown, to the Brown/ White wire of the connector. Then connect the remaining steering wheel control wire, normally Brown/White, to the Brown wire of the connector.

• Metra OE: Connect the steering wheel control Key 1 wire (Gray) to the Brown wire.

• Kenwood or select JVC with a steering wheel control wire: Connect the Blue/Yellow wire to the Brown wire.

• XITE: Connect the steering wheel control SWC-2 wire from the radio to the Brown wire.

•

Parrot Asteroid Smart or Tablet: Connect the 3.5mm jack into the AX-SWC-PARROT (sold separately), and then connect the 4-pin connector from the AX-SWC-PARROT into the radio

Note:

The radio must be updated to rev. 2.1.4 or higher software.

• Universal “2 or 3 wire” radio: Connect the steering wheel control wire, referred to as Key-A or SWC-1, to the Brown wire of the connector. Then connect the remaining steering wheel control wire, referred to as Key-B or SWC-2, to the Brown/White wire of the connector. If the radio comes with a third wire for ground, disregard this wire.

Note:

After the interface has been programmed to the vehicle, refer to the manual provided with the radio for assigning the SWC buttons. Contact the radio manufacturer for more information.

Continued on the next page

Page 3

REV. 9/25/2018 INSTAX-LR902

With the key in the off position:

• Zip tie the chime speaker under the dash to a location where it will be heard clearly by the driver, then route the harness to the radio location.

• Connect the chime speaker to the connector on AX-LR902 Interface labeled “To Speaker”.

• Connect the AX-LR902 harness to the AX-LR902 interface, and then to the wiring harness in the vehicle. The slightly longer harness with a 12-pin connector will connect at the factory radio display.

• Connect the ASWC-1 harness to the ASWC-1 interface, and then to the AX-LR902 interface.

• For all other radios: Connect the 3.5mm jack from the ASWC-1 harness, into the jack on the aftermarket radio designated for an external steering wheel control interface. Please refer to the aftermarket radios manual if in doubt as to where the 3.5mm jack goes to.

• Connect the Yellow male RCA jack labeled “To Reverse Camera Input (Radio)”, to the backup camera input.

Note:

The aftermarket radios backup camera input will be used to display the vehicle settings. If the radio doesn’t have a backup camera Input, then there will be no visualization of the vehicle settings. An externally mounted screen could be substituted in this situation.

• If installing an aftermarket backup camera, connect the Yellow female RCA jack labeled “To Reverse Camera”, to the camera.

• Press and hold the Volume-Up button on the steering wheel.

• Turn the ignition on, the L.E.D. in the ASWC-1 interface will start ﬂashing rapidly, which means the ASWC-1 is looking for the vehicle and the radio.

Note:

If the L.E.D. did not start ﬂashing rapidly, press the reset button for 3 seconds, while

still holding the Volume-Up button.

• After a few seconds the L.E.D. should stop ﬂashing rapidly, and then go out for approximately 2 seconds.

• After approximately 2 seconds there will be a series of 7 Green ﬂashes, some short, and some long. The long ﬂashes represent the wires that are connected to the ASWC-1. The 3rd, 4th, 5th, and 6th ﬂashes should be longer.

Tip:

Knowing this will help to troubleshoot, if need be.

• The L.E.D. will pause for another 2 seconds, and then ﬂash Red up to 18 times depending on which radio is connected to the ASWC-1. Refer to the L.E.D. feedback section for information.

• This is the end of the auto detection stage. Release from holding the Volume-Up button. If the ASWC-1 detected the vehicle and the radio successfully, the L.E.D. will light up solid.

• Test the steering wheel controls for proper operation. Refer to the ASWC-1 instructions online at axxessinterfaces.com for customizing the buttons, if so desired.

INSTALLING THE AX-LR902 INTERFACE

CONNECTIONS TO BE MADE (CO NT.)

PROGRAMMING THE ASWC-1 INTERFACE

Continued on the next page

Page 4

Conﬁguration Menu

• The buttons on the steering wheel will be used to operate the conﬁguration menu, which will be shown on the aftermarket radio. To enable the menu, push and hold the Talk button for 2 seconds. Use the Track Up and Track Down buttons to navigate through the menu. To select a menu option, push the Talk button once.

SCREEN OPERATION

Conﬁguration Menu

Vehicle Settings

Interface Settings

Language

Version

< Back

Continued on the next page

PROGRAMMING THE ASWC-1

INTERFACE

(CONT.)

L.E.D. feedback

The (18) Red L.E.D. ﬂashes represent what brand radio the ASWC-1 believes it is connected to. Each ﬂash represents a different radio manufacturer. For example, if you are installing a JVC radio, the

ASWC-1

will ﬂash (5) times. Following is a legend that dictates which

manufacturer corresponds to which ﬂash.

L.E.D. feedback legend

* Note:

If the ASWC-1 ﬂashes Red (7) times, and you do not have an Alpine radio connected to it, that means the ASWC-1 does not detect a radio connected it. Verify that the 3.5mm jack is connected to the correct steering wheel jack/wire in the radio.

** Note:

Part number AX-SWC-PARROT is required (sold separately). Also, the Parrot radio must be updated to rev. 2.1.4 or higher through www.parrot.com.

† Note:

If you have a Clarion radio and the steering wheel controls do not work, change the radio type to the other Clarion radio type; same for Eclipse. The following section explains how to do this

‡ Note:

If you have a Kenwood radio and the L.E.D. feedback comes back as showing as a JVC

radio, change the radio type to a Kenwood. The following section explains how to do this.

1 ﬂash - Eclipse (Type 1) † 2 ﬂashes - Kenwood ‡ 3 ﬂashes - Clarion (Type 1) † 4 ﬂashes - Sony / Dual 5 ﬂashes - JVC 6

ﬂashes -

Pioneer / Jensen 7 ﬂashes - Alpine * 8 ﬂashes - Visteon 9 ﬂashes - Valor

10 ﬂashes - Clarion (Type 2) † 11 ﬂashes - Metra OE 12 ﬂashes - Eclipse (Type 2) † 13 ﬂashes - LG 14 ﬂashes - Parrot ** 15 ﬂashes - XITE 16 ﬂashes - Philips 17 ﬂashes - TBD 18 ﬂashes - JBL

Page 5

REV. 9/25/2018 INSTAX-LR902

Vehicle Settings

• Adjust Time/Date settings such as hours, minutes, year, month, and day.

Interface Settings

• This is the main settings screen to access the settings within the interface.

Screen Size/Position

• Make sure all 4 corner markers are touching the corners of the aftermarket radios display.

SCREEN OPERATION (CONT.)

Vehicle Settings

Time/Date

< Back

Interface Settings

Screen Size/Position

Picture Settings

Preferences

<Back

Screen Size/Position

Horizontal Size

Horizontal Position

Vertical Size

Vertical Position

< Back

Continued on the next page

Page 6

Preferences

• Driver Position - Select Left or Right depending upon vehicle conﬁguration.

• Park Assist Version - Select according to the color conﬁguration of the park assist ﬁtted to the vehicle.

• Camera Connected - Select ‘Yes” if an optional backup camera will be installed.

• Reverse Priority - Select which image will be shown while the vehicle is in reverse. Options are Camera or Park Assist. The driver can select the desired image by pushing the Source button while in reverse.

Note:

This option is only available if “Camera Connected” is set to “Yes”.

• Park Brake Source - Set to Speed, Brake, or Always On.

•

Restore Factory Settings - Reverts all interface settings back to factory defaults. This will not restore the vehicle settings

Preferences

Driver Position Right Park Assist Version 0 Camera Connected Yes Reverse Priority Park Assist Park Brake Source Speed Restore factory settings < Back

Picture Settings

Brightness

Contrast

Saturation

< Back

Picture Settings

• Adjust brightness, contrast, and color saturation.

SCREEN OPERATION (CONT.)

Page 7

REV. 9/25/2018 INSTAX-LR902

Page 8

KNOWLEDGE IS POWER

Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.

Metra recommends MECP certiﬁed technicians

IMPORTANT If you are having difﬁculties with the installation of this product,

please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling.

INSTALLATION INSTRUCTIONS

AX-LR902