AX-DSP-HYKIA2
INSTALLATION INSTRUCTIONS
Hyundai / Kia Digital Signal Processor 2011-2016
TABLE OF CONTENTS
Connections to be made .......................................2
INTERFACE FEATURES
• Includes an AX-DSP (Digital Signal Processor)
• Includes an amplifier bypass harness
Installing the AX-DSP-HYKIA2 ...............................3
AX-DSP-HYKIA2 layout ..........................................4
Troubleshooting .....................................................4
• Retains BlueLink/UVO voice prompts
• Voice prompts go through the aftermarket amplifier
• Micro “B” USB updatable
OPTIONAL ACCESSORIES (sold separately)
Bass knob for AX-DSP: AX-BASSKNOB
INTERFACE COMPONENTS
• AX-DSP
• AX-DSP-HYKIA2 interface
• AX-DSP-HYKIA2 harness
• AX-DSP harness (16-pin, 20-pin)
• AX-DSP-HYKIA2 harness (12-pin black)
TOOLS REQUIRED
• Wire cutter • Crimp tool • Solder gun • Tape
• Connectors (example: butt-connectors, bell
caps, etc.)
• Amplifier bypass harness (12-pin green)
APPLICATIONS
HYUNDAI
Elantra 2012-2015
Veloster 2012-2017
KIA
Sportage 2011-2016
CAUTION!
controls panels, and especially air bag indicator
lights must be connected before cycling the
ignition. Also, do not remove the factory radio
with the key in the on position, or while the
vehicle is running.
All accessories, switches, climate
AxxessInterfaces.com © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 9/24/18 INSTAX-DSP-HYKIA2
CONNECTIONS TO BE MADE
From the AX-DSP harness to the aftermarket amplifier(s):
16-pin and 20-pin harnesses
• Connect the Blue/White wire to the amplifier turn-on wire/input.
• If installing an AX-BASSKNOB (sold separately), connect the Orange wire to the Orange
wire from the AX-BASSKNOB.
• Connect the Gray RCA jack to the right front input.
• Connect the White RCA jack to the left front input.
• Connect the Green RCA jack to the left rear input.
• Connect the Purple RCA jack to the right rear input.
• Connect the Red & White RCA jacks to the subwoofer input.
• Connect the Red RCA jack to the center channel input.
• Tape off and disregard the following (8) wires, they will not be used in future applications:
Black/Yellow, Brown, Purple, Purple/Black, Red/White, White, White/Black, White/Red
From the amplifier bypass harnesses to the aftermarket amplifier(s):
12-pin Green harness
• Connect the White wire to the front left positive.
• Connect the White/Black wire to the front left negative.
• Connect the Gray wire to the front right positive.
• Connect the Gray/Black wire to the front left negative.
• Connect the Brown/Yellow wire to the front left tweet positive.
• Connect the Brown/Blue wire to the front left tweet negative.
• Connect the White/Red wire to the front right tweet positive.
• Connect the Red/White wire to the front right tweet negative.
• Connect the Green wire to the rear left positive.
• Connect the Green/Black wire to the rear left negative.
• Connect the Purple wire to the rear left positive.
• Connect the Purple/Black wire to the rear left negative.
2
INSTALLING THE AX-DSP-HYKIA2
• Locate the factory amplifier. Refer to the amplifier location legend.
• Remove the 12-pin and 26-pin connectors from the amplifier.
• Connect the amplifier bypass harness to the 12-pin connector from the amplifier.
• Connect the AX-DSP-HYKIA2 harness to the 26-pin connector from the amplifier.
• Connect the AX-DSP harnesses to the AX-DSP.
Note: Disregard the loose 20-pin harness.
• Connect the AX-DSP-HYKIA2 harness to the AX-DSP-HYKIA2 interface.
Amplifier Location Legend
Hyundai
Azera: Right side of trunk
Elantra: Right side of trunk
Sonata: Right side of trunk
Tucson: Right side of cargo area
Veloster: Under passenger seat
Kia
Cadenza: Right side of trunk
Optima: Right side of trunk
Sorento: Under passenger seat
Soul: Right side of cargo area
Sportage: Right side of cargo area
REV. 9/24/2018 INSTAX-DSP-HYKIA2
3
To
Aftermarket
Amplifier
AX-DSP-HYKIA2 LAYOUT
AX-DSP
AX-DSP-HYKIA2
TROUBLESHOOTING
To Factory
Amplifier
Connectors
AX-DSP-HYKIA2
INSTALLATION INSTRUCTIONS
IMPORTANT
If you are having difficulties with the installation of this product,
please call our Tech Support line at 1-800-253-TECH. Before doing
so, look over the instructions a second time, and make sure the
installation was performed exactly as the instructions are stated.
Please have the vehicle apart and ready to perform troubleshooting
steps before calling.
®
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
• If the Red light in the AX-DSP-HYKIA2 interface is blinking, it is not communicating to the vehicle. Remove the key from the
ignition, unplug the connectors from the interface, and then inspect all connections made. If everything is proper, connect the
Metra recommends MECP
certified technicians
harnesses back into the interface, cycle the key to ignition, then re-inspect. The Red light should be solid.
AxxessInterfaces.com © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 9/24/18 INSTAX-DSP-HYKIA2
Loading...