INSTALLATION INSTRUCTIONS
A XBT-T Y 1
Toyota Camry Data Interface 2018-Up
Visit AxxessInterfaces.com for more detailed information about the product and up-to-date vehicle specific applications
TABLE OF CONTENTS
Connections ............................................................2
Installation .............................................................2
App Instructions .....................................................3
OPTIONAL ACCESSORIES (sold separately)
Steering Wheel Control Interface: AXSWC
TOOLS REQUIRED
• Crimping tool and connectors, or solder gun,
solder, and heat shrink • Tape • Wire cutter
• Zip ties
INTERFACE COMPONENTS
• AXBT-TY1 harness:
• 10-pin harness
• 28-pin harness
• 30-pin harness
• 12-pin AXSWC harness
INTERFACE FEATURES
• Wiring harness for installing an
aftermarket radio
• Provides power and four speakers
• Retains balance and fade
• Designed for non-amplified models
• Provides NAV outputs (parking brake,
reverse, speed sense)
• Retains the factory backup camera
• Pre-wired AXSWC harness (AXSWC sold
• Includes an AXCSD-6V 12-to-6V stepdown for the factory camera
• Allows retention and adjustment of the
* Personalization Options
• Adjust * Personalization Options through
a Bluetooth application
• Smartphone application offering full
control from either Android or Apple
mobile devices
separately)
* Actual options available vary per vehicle and per trim.
(Refer to owner’s manual for options available in vehicle.)
• 16-pin AXBT harness
• AXCSD-6V
• AXBT interface
APPLICATIONS
Toyota
Camry 2018-Up
RAV4 2019-Up
Attention! Let the vehicle sit with the key
out of the ignition for a few minutes before
removing the factory radio. When testing the
aftermarket equipment, ensure that all factory
equipment is connected before cycling the
key to ignition.
AxxessInterfaces.com © COPYRIGHT 2020 METRA ELECTRONICS CORPORATION REV. 10/5/20 INSTAXBT-TY1
CONNECTIONS
From the AXBT-TY1 harness to the aftermarket radio:
• Connect the Black wire, the Black wire labeled “CAMERA GROUND”, and also the Black wire
from the AXCSD-6V, to the ground wire.
• Connect the Yellow wire to the battery wire.
• Connect the Red wire to the accessory wire.
• Connect the Red wire labeled “CAMERA POWER 6V”, to the Blue/Red wire from the AXCSD-6V.
• Connect the reverse wire from the aftermarket radio to the Green/Purple wire, and also to
the Blue/White wire from the AXCSD-6V.
The following (2) wires are only for a multimedia/navigation radio that requires these wires.
• Connect the Blue/Pink wire to the VSS/speed sense wire
• Connect the Light Green wire to the parking brake wire
• If retaining the factory AUX-IN jack, connect the Red and White RCA jacks to the audio
AUX-IN jacks from the aftermarket radio.
• Connect the Yellow RCA jack to the backup camera input.
10-pin harness:
• Connect the Gray wire to the front right positive speaker output.
• Connect the Gray/Black wire to the front right negative speaker output.
• Connect the White wire to the front left positive speaker output.
• Connect the White/Black wire to the front left negative speaker output.
• Connect the Green wire to the rear left positive speaker output.
• Connect the Green/Black wire to the rear left negative speaker output.
• Connect the Purple wire to the rear right positive speaker output.
• Connect the Purple/Black to the rear right negative speaker output
12-pin AXSWC harness & 3.5mm jack:
This 12-pin AXSWC harness & 3.5mm jack are to be used with an AXSWC (sold separately)
to retain steering wheel audio controls. If the AXSWC is not being used, disregard this
harness and 3.5mm jack. If it is to be used, please refer to the AXSWC instructions for radio
connections and programming. Disregard the harness that comes with the AXSWC.
I N STA L L ATI O N
With the key in the off position:
1. Connect the AXBT-TY1 harness to the AXBT interface.
2. Connect the AXBT-TY1 harness to the wiring harness in the vehicle.
3. If an AXSWC (sold separately) will be used, do not connect it until after the AXBT is fully
functional.
2
APP INSTRUCTIONS
1. Download and install the AXBT app from the mobile devices app store.
2. Start the vehicle.
3. Open the app and wait for the Customization Settings menu to appear. If Not Connected
appears instead, press the right button in the top right corner of the screen, then press the
left button in the top right corner of the screen to go back to Customization Settings. The
pairing process will begin at this point.
4. Once paired, Settings will be displayed in the screen. From this point on you can make
changes to the vehicle as desired, as the long as the vehicle is on. (Figure A)
Note: Screenshot shown for illustration only.
Actual options available vary per vehicle and
per trim.
Note: The app must be paired with the
interface at least once for the initial setup.
Failure to do so will prevent the interface from
functioning.
(Figure A)
Other Options
Manage Vehicles (Figure B)
• Select Manage Vehicles by pressing the button in the top right of the screen.
• Pressing either the Add Vehicle or Edit (pencil icon) button will open the Configure Vehicle
menu. (Figure B)
Configure Vehicle (Figure C)
• The name of the vehicle can be changed by pressing the text field.
• The app can automatically detect the interface installed in the vehicle by pressing the Search
button (magnifying glass).
• The Make and Model fields will open a drop down list for the user to select the make and
model of the vehicle that the interface is installed in.
• Press the Save
button to store
the changes.
(Figure B)
(Figure C)
REV. 10/5/2020 INSTAXBT-TY1
3
INSTALLATION INSTRUCTIONS
A XBT-T Y 1
Having difficulties? We’re here to help.
Contact our Tech Support line at:
Or via email at:
techsupport@metra-autosound.com
Tech Support Hours (Eastern Standard Time)
Monday - Friday: 9:00 AM - 7:00 PM
Saturday: 10:00 AM - 7:00 PM
Sunday: 10:00 AM - 4:00 PM
386-257-1187
®
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
Metra recommends MECP
certified technicians
AxxessInterfaces.com © COPYRIGHT 2020 METRA ELECTRONICS CORPORATION REV. 10/5/20 INSTAXBT-TY1
Loading...