User Manual
January 2008 Revision 1.0
Point - of - Sale
Monitor
2
Copyright 2008 Jan.
All Rights Reserved
Manual Version 1.0
The information contained in this document is subject to change without notice.
We make no warranty of any kind with regard to this material, including, but not limited
to, the implied warranties of merchantability and fitness for a particular purpose. We
shall not be liable for errors contained herein or for incidental or consequential damages
in connection with the furnishing, performance, or use of this material.
This document contains proprietary information that is protected by copyright. All rights
are reserved. No part of this document may be photocopied, reproduced or translated
to another language without the prior written consent of the manufacturer.
TRADEMARK
Intel®, Pentium® and MMX are registered trademarks of Intel® Corporation. Microsoft®
and Windows® are registered trademarks of Microsoft Corporation. ELO Touch is the
registered trademark of ELO Touch Systems.
3
Safety
IMPORTANT SAFETY INSTRUCTIONS
1. To disconnect the machine from the electrial power supply, turn off the power switch
and remove the power cord plug from the wall socket. The wall socket must be
easily accessible and in close proximity to the machine.
2. Read these instructions carefully. Save these instructions for future reference.
3. Follow all warnings and instructions marked on the product.
4. Do not use this product near water.
5. Do not place this product on an unstable cart,stand,or table.The product may fall,
causing serious damage to the product.
6. Slots and openings in the cabinet and the back or bottom are provided for
ventilation;to ensure reliable operation of the product and to protect it from
overheating. These openings must not be blocked or covered.The openings should
never be blocked by placing the product on a bed, sofa, rug, or other similar
surface.This product should never be placed near or over a radiator or heat
register,or in a built-in installation unless proper ventilation is provided.
7. This product should be operated from the type of power indicated on the marking
label.If you are not sure of the type of power available, consult your dealer or local
power company.
8. Do not allow anything to rest on the power cord. Do not locate this product where
persons will walk on the cord.
9. Never push objects of any kind into this product through cabinet slots as they may
touch dangerous voltage points or short out parts that could result in a fire or electric
shock. Never spill liquid of any kind on the product.
CE MARK
This device complies with the requirements of the EEC directive
89/336/EEC with regard to “Electromagnetic compatibility” and 73/23/EEC
“Low Voltage Directive”.
FCC
This device complies with part 15 of the FCC rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may
cause undesired operation.
4
LEGISLATION AND WEEE SYMBOL
2002/96/EC Waste Electrical and Electronic Equipment Directive on the treatment,
collection, recycling and disposal of electric and electronic devices and their
components.
The crossed dustbin symbol on the device means that it should not be disposed of with
other household wastes at the end of its working life. Instead, the device should be
taken to the waste collection centers for activation of the treatment, collection, recycling
and disposal procedure.
To prevent possible harm to the environment or human health from uncontrolled waste
disposal, please separate this from other types of wastes and recycle it responsibly to
promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product,
or their local government office, for details of where and how they can take this item for
environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the
purchase contract.
This product should not be mixed with other commercial wastes for disposal.
5
Revision History
Revision
Number
Description Revision Date
1.0 Initial release 2008 January
6
Table of Contents
1. Item Checklist...............................................................................................7
1.1. Standard Items........................................................................................7
1.2. Optional Items.........................................................................................8
2. System View.................................................................................................9
2.1. Front View...............................................................................................9
2.2. Rear View ...............................................................................................9
2.3. I/O View................................................................................................10
3. Drivers Installation.....................................................................................11
3.1. Driver List..............................................................................................11
3.2. ELO Touch Driver Installation................................................................11
3.3. POSTouch Driver Installation................................................................13
4. System Installation ....................................................................................16
4.1. VESA Installation..................................................................................16
4.2. Stand Holder Installation.......................................................................17
4.3. VFD Installation.....................................................................................18
4.4. MSR Installation....................................................................................20
4.5. Power Cord Installation.........................................................................22
5. System Disassembly .................................................................................23
5.1. Removing the Stand and the Stand holder............................................23
5.2. Opening the I/O Cover..........................................................................24
5.3. Opening the Rear Cover.......................................................................24
5.4. Replacing the Scalar Board..................................................................25
5.5. Replacing the Inverter Board................................................................26
5.6. Replacing the OSD Board.....................................................................27
6. Specification...............................................................................................28
7. Connectors and Jumper Settings.............................................................29
7.1. B13 Scalar board..................................................................................29
7.2. Jumper Settings....................................................................................30
7.3. Connectors ...........................................................................................31
7.4. Connectors Pin Definition .....................................................................32
7
1. Item Checklist
Take the system unit out of the carton. Remove the unit from the carton by holding it by
the foam inserts. The following contents should be found in the carton:
1.1. Standard Items
a. Driver CD
b. Power Adapter
c. Power Cable ( 220V or 110V)
d. System
8
1.2. Optional Items
a. MSR
b. VFD
9
2. System View
2.1. Front View
2.2. Rear View
Touch Screen
I/O
VESA Mount
Cable Cover
Hole Plug
10
2.3. I/O View
DC- In
VGA in
PS/2 in
USB in
COM out
COM in
PS/2 out
USB out
Power
Left Select
Menu
Right
11
3. Drivers Installation
3.1. Driver List
Folder/File File Description
<CD>:\POS720.htm B13 Driver List
<CD>:\COMMON\Elo_Touch ELO Touch Driver
<CD>:\COMMON\POS_Touch POSTouch Driver
-The following procedures are for Windows 2000/XP, other platforms are similar.
3.2. ELO Touch Driver Installation
a. Click ”sw500930” on the My computer
window.
b. Click the “OK” button on the Welcome
window.
c. Click the ”Unzip” button on the WinZip
Self-Extractor window.
d. Select “Install Serial Touchscreen
Drivers” and then click the “Next”
button
on the Welcome window.
12
e. Click the “Yes” button on the License
Agreement window.
f. Click the “Next” button on the on the
“Select the COM ports…” window.
g. Select “COM5” and click the “Next”
button on the Choose the COM ports…
window.
h. Click the “Next” button on the You have
selected the COM ports…window.
i. Click the “Finish” button on the Setup
Complete window
j. Click the “Yes” button and restart your
system.
13
k. After the computer has restarted, click
“Align” on the Elo Touchscreen
Properties window.
l. Follow the instructions on the screen to
calibrate the touch panel.
3.3. POSTouch Driver Installation
a. Double click the ”Setup” on the “My
Computer” window.
b. Click the “Next“ button on the “Welcome
window”.
c. Click the ”Yes” button on the “License
Agreement” window.
d. Click the ”Next” button on the “Choose
Destination Location” window.
14
e. Click the “Next” button on the “Select
Program Folder” window.
f. Click the “Finish” button on the “Install
Shield Wizard Complete” window.
g. Click the “Continue Anyway “button on
the “Hardware Installation” window.
h. Select the “Yes” and click the”OK”
button
and restart your system.
i. After the computer has restarted, select
“Programs àTouchUtility àScan RS232
Touch Device”.
j. The serial ports are scanned for a touch
device.
15
k. Select “Programs àTouchUtility à
Touch
Utility”.
l. Click “Scale / Offset” on the POSTouch
Utility window.
m. Follow the instructions on the screen to
do a three point calibration of the touch
panel.
n. Select “Device à9Pts Calibration”
on the
POSTouch Utility window.
o. Follow the instructions on the screen to
do a nine point calibration of the touch
panel.
16
4. System Installation
4.1. VESA Installation
a. Place the panel bracket on the on the back of the system, and align the
bracket holes with the VESA holes of the system.
Tighten the screws (4)"
b. Place the wall mount kit on the
panel bracket and tighten the screw
(1)
c. Attach the panel to the wall mount
bracket and tighten the thumb screw
to finish the Wall Mount Installation
17
4.2. Stand Holder Installation
a. Slide the stand bracket into the position
b. Tighten the screws (6), 3 on each side
c. Attach the stand holder to the VESA holds and tighten the screws (4)
18
d. Attach the panel to the stand bracket
e. Tighten the thumbscrew (1)
4.3. VFD Installation
a. Place the VFD holder on the VFD bracket and tighten the thumb screws (2)
19
b. Attach the VFD holder on the rear cover and tighten the screws (2). Put the
VFD cable through the VESA bracket
c. The cable should come out from the bottom side of the VESA bracket and
band over in order to connect to the I/O port
d. Connect to the COM port as shown by the picture to finish the installation
20
4.4. MSR Installation
a. Loosen the screws (2)
b. slide the MSR into the position
c. Tighten the screws (2)
21
d. Put the MSR cable through the holders(2)
e. Connect the MSR cable to the PS2 socket to finish the installation
22
4.5. Power Cord Installation
a. Connect the power cord to the adaptor
b. Place the cable on the holder and clip to properly locate it. Route through the
base gap for cable management
23
5. System Disassembly
5.1. Removing the Stand and the Stand holder
a. Loosen the thumbscrew (1)
b. Lift the panel up and separate it from the stand bracket
24
5.2. Opening the I/O Cover
To open the I/O cover, please first follow the steps in chapter 5.1
a. Loosen the thumbscrews (2)
b. Remove the I/O cover from the panel
5.3. Opening the Rear Cover
To open the rear cover, please first follow the steps in chapter 5.1
a. Remove the screws (17) to remove the rear cover
25
5.4. Replacing the Scalar Board
To replace the scalar board, please first follow the steps in chapter 5.1, 5.2 and 5.3
a. Remove the hex screws(4)
b. Disconnect the cables (4)
c. Remove the screws (5) then slide the scalar board to the direction as shown by the
arrows to replace it
26
5.5. Replacing the Inverter Board
To replace the inverter board, please first follow the steps in chapter 5.1, 5.2, and5.3.
a. Disconnect the cables (3)
b. remove the screws (2) to replace the inverter board
27
5.6. Replacing the OSD Board
To replace the OSD board, please first follow the steps in chapter 5.1, 5.2, and5.3.
a. Disconnect the cables (4)
b. Remove the screws (6) to replace the OSD board
28
6. Specification
Main board B13
LCD Panel
Panel Size 12.1" TFT LCD 15" TFT LCD 17" TFT LCD
Brightness 400nits 350nits 300nits
Resolution 800 x 600 1024 x 768 1280 x 1024
Touch Resistive / IR type (Option, replace Tempered Glass)
External I/O Ports
VGA 1
PS/2 2 (1XPS/2 in to PC, 1XPS/2 out to MSR /Keyboard)
OSD Button 5 (power, menu, left, right, select)
USB 2x USB (type A), 1x USB ( type B) to PC
Serial / COM 2 x COM (1 x DB-9/F type to PC) 1x RJ45 type to VFD
Power adapter
Power Source 12V /2.5A 30W 12V /5A 60W
Peripheral
Metal MSR
3 Tracks ( PS/2 )
Metal Customer
Display
Flush mount VFD (COM )
Environment
EMC & Safety FCC Class A, CE, LVD
Operating
Temperature
0°C ~ 40°C ( 41°F ~ 95°F )
Storage
Temperature
-20°C ~ 60°C ( -4°F ~ 140°F )
Operating
Humidity
5% ~ 95% RH non condensing
Storage Humidity
5% ~ 95% RH non condensing
Dust & Water
Proof
IP55 (Front bezel)
90° Angle
331 x 250 x 346mm
13” x 9.8” x 13.6”
90° Angle
386 x 250 x 370mm
15.2” x 9.8” x 14.6”
90° Angle
411 x 250 x 390mm
16.2” x 9.8” x 15.4” Dimension
(W x D x H)
Wall mount
331 x 55 x 260mm
13” x 2.2” x 10.2”
Wall mount
386 x 60 x 308mm
15.2” x 2.4” x 12.1”
Wall mount
411 x 60 x 345mm
16.2” x 2.4” x 13.6”
Mounting
75mm x 75mm
Standard VESA
100mm x 100mm Standard VESA
- This specification is subject to change without prior notice.
29
7. Connectors and Jumper Settings
7.1. B13 Scalar board
30
7.2. Jumper Settings
7.2.1 Power Mode Setting
Function JP4
◎ On
1-2
Off N/C
7.2.2 COM3 Power Setting
Function JP9
◎ COM3 PIN10_RI
1-2
COM3 PIN10_+5V 3-4
COM3 PIN10_+12V 5-6
7.2.3 USB Touch Setting
Function JP10
◎ Docking
3-5, 4-6
On Board 1-3, 2-4
7.2.4 COM Port RS232 Touch / Int. COM / RS232 Card Reader/ Ext. COM Setting
Function JP2 JP3 JP7 JP8
◎ RS232 Touch
1-2, 3-4, 5-6, 7-8 1-2, 5-6 1-2, 5-6
Note:
OPEN
SHORT
31
7.3. Connectors
Connector Function
CN1 LCD Interface Connector
CN2 Inverter Connector
CN3 Resistive Touch Panel Connector
CN4 Power State LED Connector
CN5 VGA Extender Connector
CN6 Power ON/OFF Connector (Reserve)
CN8 GM2621 SPI Connector (Reserve)
CN9 Internal USB Device Connector (Down-Stream)
CN10 Internal COM Device Connector (Output)
CN11 Keypad Connector
CN12 Card Reader Connector
CN13 DVI Connector
COM1 COM Port Connector (Input)
PS1 P/S2 Input Connector
PS2 P/S2 Output Connector
PWR1 +12V Input
PWR2 +12V Input (Internal)
RJ45_1 COM Port Connector (Output)
USB1 USB Port (Down-Stream x2)
USB3 USB Port (Upstream)
VGA1 VGA Input Connector
32
7.4. Connectors Pin Definition
CN1: LVDS Interface
Pin 1 LVDS_B0+ Pin 2 LVDS_A3+
Pin 3 LVDS_B0- Pin 4 LVDS_A3Pin 5 GND Pin 6 GND
Pin 7 LVDS_B1+ Pin 8 LVDS_CLKA+
Pin 9 LVDS_B1- Pin 10 LVDS_CLKAPin 11 GND Pin 12 GND
Pin 13 LVDS_B2+ Pin 14 LVDS_A2+
Pin 15 LVDS_B2- Pin 16 LVDS_A2Pin 17 GND Pin 18 GND
Pin 19 LVDS_B3+ Pin 20 LVDS_A1+
Pin 21 LVDS_B3- Pin 22 LVDS_A1Pin 23 GND Pin 24 GND
Pin 25 LVDS_CLKB+ Pin 26 LVDS_A0+
Pin 27 LVDS_CLKB- Pin 28 LVDS_A0Pin 29 GND Pin 30 GND
Pin 31 +5V_LCDVDD Pin 32 +3.3V_LCDVDD
Pin 33 +5V_LCDVDD Pin 34 +3.3V_LCDVDD
Pin 35 +5V_LCDVDD Pin 36 +3.3V_LCDVDD
Pin 37 +5V_LCDVDD Pin 38 +3.3V_LCDVDD
Pin 39 +5V_LCDVDD Pin 40 +3.3V_LCDVDD
CN2: Inverter Connector
Pin 1 +12V_INV Pin 2 +12V_INV
Pin 3 +12V_INV Pin 4 +12V_INV
Pin 5 Back-Light Enable Pin 6 N/C
Pin 7 N/C Pin 8 Brightness Control
Pin 9 GND Pin 10 GND
Pin 11 GND Pin 12 GND
CN3: Resistive Touch Panel Connector
Pin 1 ESD1 Pin 2 ESD2
Pin 3 ESD3 Pin 4 ESD4
Pin 5 ESD5 Pin 6 N/C
33
CN4: Power State LED Connector
Pin 1 LED_On Pin 2 GND
Pin 3 LED_Off
CN5: VGA Extender Connector
Pin 1 +5_+12V Power Pin 2 +5_+12V Power
Pin 3 GND Pin 4 VGA_CAT5_DATA
Pin 5 VGA_CAT5_CLK Pin 6 VGA_CAT5_VSYNC
Pin 7 VGA_CAT5_/HSYNC Pin 8 GND
Pin 9 CAT5_EN# Pin 10 GND
Pin 11 VGA_CAT5_B+ Pin 12 VGA_CAT5_G+
Pin 13 VGA_CAT5_R+
CN8: GM2621 SPI Connector (Reserve)
Pin 1 N/C Pin 2 RS232_SPI_RX#
Pin 3 RS232_SPI_TX# Pin 4 GND
CN9: Internal USB Device Connector (Down-Stream)
Pin 1 +5V Pin 2 USB20_R_PPin 3 USB20_R_P+ Pin 4 GND
Pin 5 BUFFER_CTRL_ELO
CN10: Internal COM Device Connector (Output)
Pin 1 DCD# Pin 2 RX#
Pin 3 TX# Pin 4 DTR#
Pin 5 GND Pin 6 DSR#
Pin 7 RTS# Pin 8 CTS#
Pin 9 RI# Pin 10 +5V
CN11: Keypad
Pin 1 +3.3V_GM2621 Pin 2 GPIO_LED_OFF#
Pin 3 GPIO_LED_ON# Pin 4 KEYPAD_IN
Pin 5 KEYPAD_GND Pin 6 GND
34
CN12: Card Reader Connector
Pin 1 +5V Pin 2 +5V
Pin 3 KDATA_SIO_TO_MSR Pin 4 KDATA_SIO_TO_MSR
Pin 5 KDATA_MSR_TO_GFINGER Pin 6 KCLK_MSR_TO_GHINGER
Pin 7 RS232_6_RX# Pin 8 RS232_6_TX#
Pin 9 RS232_6_CTS# Pin 10 RS232_6_RTS#
Pin 11 KB_EN Pin 12 GND
Pin 13 USB20_MSR_P0+ Pin 14 USB20_MSR_P0Pin 15 GND
CN13: DVI Connector
Pin 1 GND Pin 2 TMDS_A0+
Pin 3 DVI_DET Pin 4 TMDS_A0Pin 5 GND Pin 6 GND
Pin 7 +5V_DVI Pin 8 TMDS_A1+
Pin 9 N/C Pin 10 TMDS_A1Pin 11 GND Pin 12 GND
Pin 13 N/C Pin 14 TMDS_A2+
Pin 15 N/C Pin 16 TMDS_A2Pin 17 DVI_R_DDC_DATA Pin 18 GND
Pin 19 DVI_R_DDC_CLK Pin 20 TMDS_CLKA+
Pin 21 N/C Pin 22 TMDS_CLKAPin 23 N/C Pin 24 GND
Pin 25 N/C Pin 26 N/C
Pin 27 N/C Pin 28 N/C
Pin 29 N/C Pin 30 GND
COM1: COM Port Connector (Input)
Pin 1 RS232_DCD# Pin 2 RS232_RX#
Pin 3 RS232_TX# Pin 4 RS232_DTR#
Pin 5 GND Pin 6 RS232_1_DSR#
Pin 7 RS232_RTS# Pin 8 RS232_1_CTS#
Pin 9 RS232_RI
Loading...