MANUALE V1.2B
-2-
CONTENTS
Chapter 1. Introduction
Chapter 3. BIOS Setup Utility
Chapter 5. Motherboard
1-1. Warranty ………………………………………………….
3
3-1. BIOS Setup Program …………………………………..
33
5-1. Motherboard Layout ………………………………………………
76
1-2. Copyright ………………………………………………..
4
3-2. BIOS Menu Screen ………………………………...…...
36
5-2. Clearing CMOS ……………………………………………………….
78
1-3. Safety Information ….………..…………………….
4
3-3. Standard CMOS Features …………………………..
37
5-3. Serial Port Power Jumper Settings………………………….
79
1-4. Liability Limitation ………..…………………………
5
3-4. Advanced BIOS Features ..…………………………..
40
5-4. STACON1 ………………………………………………………………..
80
1-5. Installation Recommendations ……………….
7
3-5. Advanced Chipset Features ………………………..
46
3-6. Integrated Peripherals ………………………………..
49
3-7. Power Management Setup ………………………...
57
Chapter 2. Product Overview
3-8. PnP/PCI Configuration …..……………………………
61
Chapter 6. Maintenance
2-1. Inside Your Package ………………………………..
8
3-9. PC Health Status …………………………………………
63
6-1. Safety Warning ……………………………………………………….
81
2-2. Pre-installation Preparation ...………………….
13
3-10. Load Optimized Defaults ………………………….
66
- HDD Replacement ...…………………………………………………..
82
2-3. Product Outline .……………………………………...
13
3-11. Set Supervisor Password ………………………….
67
- Motherboard Replacement .………………………………………
84
2-4. Installation of Optional Devices ……………..
17
3-12. Set User Password ……………………………………
69
- Memory Replacement ……………………………………………….
86
- CDP Installation ……………………………………………
17
3-13. Save & Exit Setup …………………………………….
71
- SSD Replacement ………………………………………………………
87
- Mini Keyboard Installation …………….…….……...
19
3-14. Exit Without Saving ………………………………….
72
- MSR Replacement ……………………………………………………..
88
- Connection via USB Port .…………………………….
20
- Paper-Roll Replacement …………………………………………….
89
- Connection via Ethernet Port (LAN) ……….…..
21
Chapter 4. Troubleshooting
- Printer Replacement ………………………………………………….
90
- Cash Drawer Connection ……………………..……...
22
4-1. Network Issues …………………………………………...
73
6-2. Technical Specifications ………….…..……………..…………..
92
- Power Cable Connection ..…..…………………........
23
4-2. MSR Issues ………………………………………………….
73
- miniO Main Unit ………………………………………………………..
92
2-5. Basic Operations ……………………………………….
24
4-3. USB Issues ……………………………………………….….
74
- Integrated Printer …………………………………….………………..
94
- Switching On POS ………….…………………………….
24
4-4. LCD Issues …………………………………………………..
74
- Shutting Down POS ……………………………………..
25
4-5. Touch-screen Issues ……………………………….…..
74
- Integrated Printer: Control Panel ..………...…….
26
4-6. Power Issues …………………….…………………………
75
- Integrated Printer: Self-test ..…….………..………..
27
4-7. Booting Issues …………….……..……………………….
75
- Integrated Printer: DIP Switch Settings ...…….
28
4-8. Printer Issues ……………………...………………………
75
-3-
Chapter 1. Introduction
1-1. Warranty
We guarantee our POS terminal product and its parts against defects in materials and workmanship, under proper use, for a standard period of
2 years from the original date of purchase.
During this period, we will repair or replace defective and/or faulty products or parts without charge to the customer for parts and labor.
The 1st year includes servicing and new or refurbished replacement parts free of charge, with one-way shipping costs borne by the seller. The
customer shall, however, be responsible for the return delivery costs.
The 2nd year also includes free of charge servicing and parts, but a limited warranty requires the entire shipping cost to be borne by the
customer.
Products out of the warranty period or scope shall be diagnosed at the customer's expense.
In the case of product damage due to error on part of the consumer, incorrect usage, carelessness or natural phenomenon, the customer shall
bear the full cost for both repair and delivery.
-4-
1-2. Copyright
This publication, including all photographs, illustrations and software, is protected under international copyright law with all rights reserved to the
manufacturer. Neither this manual, nor any of the material contained herein, may be reproduced without express written consent of the author.
1-3. Safety Information
1. Always ensure that the correct power voltage is used as a precaution against fire and electrical shock.
2. Avoid exposing product to direct sunlight. Do not use product in areas of high humidity.
Doing so may cause low reliability and/or operational malfunction.
3. Be careful of static electricity on PCB of system with anti-static appliances. Doing so may cause inferior reliability and shorted product life.
4. Keep product away from highly static areas. This may lead to inferior performance and reduced life cycle.
5. Do not interfere with, or obstruct metal components inside product. Doing so may cause the risk of fire or electric shock.
6. Do not pull on power cable or peripheral devices‟ connector cable. Doing so may cause fire, electric shock or electronic system malfunction.
7. Use caution when around other electronic devices with possible high frequency or electro-magnetic effects e.g. Audio, Electronic-range etc.
Doing so will lead to the serious risk of product malfunctioning or a system error occurring.
8. Ensure that batteries are replaced correctly. Failure to do this may result in sudden explosions.
9. Dispose of used batteries properly according to the instructions.
-5-
1-4. Liability Limitation
● Installation and maintenance
We recommend that you inquire about product installation, maintenance and repair service from the official service center and agent office.
POSBANK takes no responsibility for malfunctions or system errors occurring after service and/or system check carried out by unofficial service providers.
● High frequency appliances
This product is qualified by FCC, CE, EMI and MIC compliances, and is thus governed by these qualifications‟ safety regulations.
However, the product can affect and be affected by other high frequencies generated around it. As such, POSBANK does not consider liability for any system
error or disorder due to this issue.
● Electronic noise emitting equipment
We recommend using the product away from electronic noise emitting equipment such as heaters, motors, fluorescent lights, TVs etc. as it may cause
interruption or interference with normal operation.
● Installation location
For optimal performance, the product should be kept in an environment of lower than 65% humidity and in a temperature of 10 ~ 30℃. Please also keep
away from direct sun-light.
-6-
● Cleaning procedure
Cleaning with chemical based products (in particular those containing benzyl or chemical thinning agents) can damage the exterior surfaces of the product.
We recommend using a soft damp cloth and wiping gently, taking particular care when dealing with the LCD display screen.
● Product limitations
1. The use of this product for anything other than POS tasks is strictly prohibited.
The product is not supported for regular PC and interface operation.
2. This product is for business use only, and not for usage in the home.
3. Both hardware and software are both fully configured.
4. Normal operating is guaranteed on a steady power connection.
-7-
1-5. Installation Recommendations
1. Avoid installing during thunderstorms. (Possibility of dangerous exposure to electricity.)
2. Install away from damp spaces or water-leaks.
3. Beware of static occurrence during installation.
4. Use only ground connected and quality certified power cords and cables.
5. Keep out of direct sun-light, extremely high or low temperatures, or high humidity areas.
6. Install product away from areas prone to shocks or vibration.
7. Install product away from sewing machines, welding equipment, electric stoves, audio equipment and other high frequency generating
equipment.
8. Installation and use in close proximity to an air-conditioning unit is not recommended.
9. Do not connect cables underneath carpets or floorboards.
10. Only use power cables supplied by pre-approved and certified venders.
11. Never use power cords from high power source appliances.
e.g. Electronic heaters, Electric stoves, Audio equipment, Air-conditioners, Refrigerators etc.
12. The use of multiple connections in a shared power outlet/socket is not recommended.
-8-
Chapter 2. Product Overview
2-1. Inside Your Package
1. Please check your package and confirm its contents.
2. The POS terminal main unit, power cable, user manual, roll paper and driver CD are included in the package. If any items are missing or
damaged, please contact your dealer for assistance.
-9-
[Package Contents]
miniO main unit
User manual Power cable
Driver CD Roll paper
-10-
[Optional: Customer Display (CDP)]
Normal CDP
Pole type CDP
-11-
[Optional: PLU Keyboard]
PLU Keyboard: 55Key
Image of Main Unit with PLU Keyboard
-12-
[Optional: Mini Keyboard]
Mini Keyboard
Image of Main Unit with Mini Keyboard
-13-
2-2. Pre-installation Preparation
1. Remove protective film from touch-screen to prevent possible operating difficulties.
2. Attach all optional parts before setting up the main POS unit.
2-3. Product Outline
- Each part of product may differ depending on the specific POS model.
- Model-specific data sheets are provided on our website
-14-
[Side View]
2” Printer
Printer OPEN button
Printer FEED switch
CF card socket
LCD & Touch-panel display
Smart Card Reader
(SCR)
Magnetic Stripe
Reader (MSR)
Printer RESET switch
Printer ON, Error LED
-15-
[Top View]
Customer display
(optional)
Power, HDD, LAN LED
Power switch
I-Button
Keyboard LOCK switch
RESET switch
USB port
-16-
[Power & I/O Ports]
Description
Description
1
USB port
5
Power connector
2
Ethernet port (LAN)
6
Fiscal / PC switch
3
Cash box port
7
Modem port
4
COM1, COM2 port
① ② ③ ④ ⑤ ⑥ ⑦
-17-
2-4. Installation of Optional Devices
[CDP Installation] Warning: Completely remove power cable when opening main unit or installing optional devices.
1. Insert (-) driver in the grooves marked ↑ and detach cover from main unit.
2. Connect to the main unit using the CDP-cable and install.
After successful installation of O/S,
default text will be displayed on the CDP
upon the POS unit being reset.
-18-
[CDP Installation: Pole Type] Warning: Completely remove power cable when opening main unit or installing optional devices.
1. Insert (-) driver in the grooves marked ↑ and detach cover from main unit.
2. Connect to the main unit using the CDP-cable and install.
After successful installation of O/S,
default text will be displayed on the CDP
upon the POS unit being reset.
-19-
[Mini Keyboard Installation] Warning: Completely remove power cable during installation
1. Put (-) driver in the grooves marked ↓ and detach dummy cover from
main unit.
2. Connect cable to interface connector.
3. Insert keyboard into main unit from above.
*After successful installation of O/S, an LED will light up in the upper-left
corner of the keyboard upon the POS being reset.
-20-
[Connection via USB Port]
Three USB ports are provided in the POS unit, two at the rear I/O and one at the side, all of which support the standard USB 2.0.
Some USB devices (optional devices) are only functional with specific driver software installed.
If multiple USB devices are used together, this may result in abnormal functionality.
Using a USB hub with external adapter for supplying power is recommended.
Dependent on the type of device, it is possible for the USB device to be recognized later than normal.
-21-
[Connection via Ethernet Port (LAN)]
The Ethernet port located at the rear I/O supports 10/100/1000Mbps using an RJ45 connector cable.
When connected properly, the LAN LED light will be switched on.
-22-
[Cash Drawer Connection]
The cash drawer port (RJ11) is located at the rear I/O, and supports 24V Solenoid type.
The cash drawer port is connected to the internal printer on the mother board. The POS will not operate properly if no printer is attached to
the POS.
* The miniO
only
supports cash drawers that are compatible with EPSON.
-23-
[Power Cable Connection]
Insert power cable into power connector socket.
INPUT: 100-240V~,50/60Hz 1.5A OUTPUT: DC 24V 2.5A
-24-
2-5. Basic Operations
[Switching On POS]
» Ensure that all additional POS accessories and peripherals are switched on before switching on the POS.
1. Press „Power‟ button on the POS unit. (POWER LED will light up.) 2. Confirm that Windows is booting.
Power switch
-25-
[Shutting Down POS]
For product stability, it is recommended closing Windows directly in the O/S by clicking „Start‟ -> „Turn Off Computer‟ -> „Shut Down‟.
Please make sure that you have closed all applications before terminating Windows.
* Alternatively, you may shut down Windows by simply pressing the „Power‟ switch on the Main Unit.
You may also perform a system-reboot by pressing the „Reset‟ button on the Main board.
Power button
Main board reset
button
-26-
[Integrated Printer: Control Panel]
OPEN (Button): Press to open the integrated printer.
FEED (Button): Press the FEED button once to discharge
extra paper. Holding down the FEED button will discharge
paper continuously until the button is released again.
PRINTER ON, ERROR LED: Displays: Printer status;
Error; Paper-shortage.
RESET (Button): Reset printing data to initial stage
-27-
[Integrated Printer: Self-test]
1. Ensure the paper roll is installed correctly.
2. The self-test prints out the current firmware version and DIP switch
settings.
3. Self-test 1 (When miniO is powered Off)
While holding down the FEED button, turn on the power to begin the
self-test.
4. Self-test 2 (When miniO is powered On)
While holding down the printer RESET button, press the FEED button.
Next, release the printer RESET button and the self-test will begin.
5. Two pages will be printed in total:
1. Current printer status
2. Font display
6. Upon completion of the self-tests, press the RESET button to resume
operation.
-28-
[Integrated Printer: DIP Switch Settings]
1. Detach integrated printer from main unit.
2. Check DIP SW on underside of printer.
Warning: Ensure power is OFF when changing the dip switch settings.
Tip: Change density setting to "Normal" when printing with "B" Font
-29-
No
Function
Setting
Default
1
RS232-C
(Transmission
speed)
SW1-1
SW1-2
SW1-3
9600 BPS
2400 BPS
OFF
OFF
OFF
4800 BPS
ON
OFF
OFF
9600 BPS
OFF
ON
OFF
19200 BPS
ON
ON
OFF
38400 BPS
OFF
OFF
ON
57600 BPS
ON
OFF
ON
115200 BPS
OFF
ON
ON
2
RS232-C
(Handshaking)
SW1-4
DTR/DSR
DTR/DSR
OFF
XON/XOFF
ON
3
Auto
cutter
SW2-7
Enable
Enable
OFF
Disable
ON
4
Sound
SW1-5
SW1-6
No Sound
No Sound
OFF
OFF
Internal
buzzer
ON
OFF
External
buzzer
OFF
ON
Voice
ON
ON
-30-
No
Function
Setting
Default
5
Print density
SW1-7
SW1-8
Low
Low power
OFF
OFF
Normal
ON
OFF
Slightly
OFF
ON
Dark
ON
ON
6
Auto cutter
function
SW2-8
Partial cut
Partial cut
OFF
Full cut
ON
-31-
[Language Settings]
NO
CODE PAGE
LANGUAGE
SW2-1
SW2-2
SW2-3
SW2-4
SW2-5
SW2-6
1
CP-437
English
USA/Standard Europe
OFF
OFF
OFF
OFF
OFF
OFF
2
Katakana
Japanese
ON
OFF
OFF
OFF
OFF
OFF 3 CP-850
Multilingual
OFF
ON
OFF
OFF
OFF
OFF 4 CP-860
Portuguese
ON
ON
OFF
OFF
OFF
OFF 5 CP 863
Canadian-French
OFF
OFF
ON
OFF
OFF
OFF
6
CP-865
Nordic
ON
OFF
ON
OFF
OFF
OFF 7 CP-1252
Latin I
OFF
ON
ON
OFF
OFF
OFF 8 CP-866
Cyrillic Russian
ON
ON
ON
OFF
OFF
OFF
9
CP-852
Latin II
OFF
OFF
OFF
ON
OFF
OFF
10
CP-858
Euro
ON
OFF
OFF
ON
OFF
OFF
11
Thai-42
Thailand characters
OFF
ON
OFF
ON
OFF
OFF
12
Thai-11
ON
ON
OFF
ON
OFF
OFF
13
Thai-14
Thailand characters
OFF
OFF
ON
ON
OFF
OFF
14
Thai-16
ON
OFF
ON
ON
OFF
OFF
15
Thai-18
OFF
ON
ON
ON
OFF
OFF
16
CP-874
ON
ON
ON
ON
OFF
OFF
17
CP-737
Greek
OFF
OFF
OFF
OFF
ON
OFF
18
CP-775
Baltic
ON
OFF
OFF
OFF
ON
OFF
19
CP-855
Cyrillic
OFF
ON
OFF
OFF
ON
OFF
20
CP-857
Turkish
ON
ON
OFF
OFF
ON
OFF
21
CP-861
Icelandic
OFF
OFF
ON
OFF
ON
OFF
22
CP-862
Hebrew
ON
OFF
ON
OFF
ON
OFF
23
CP-864
Arabic
OFF
ON
ON
OFF
ON
OFF
24
CP-869
Greek II
ON
ON
ON
OFF
ON
OFF
-32-
25
CP-1251
Cyrillic
OFF
OFF
OFF
ON
ON
OFF
26
CP-1253
Greek
ON
OFF
OFF
ON
ON
OFF
27
CP-1254
Turkish
OFF
ON
OFF
ON
ON
OFF
28
CP-1255
Hebrew
ON
ON
OFF
ON
ON
OFF
29
CP-1256
Arabic
OFF
OFF
ON
ON
ON
OFF
30
CP-1257
Baltic
ON
OFF
ON
ON
ON
OFF
31
CP-1258
Vietnamese
OFF
ON
ON
ON
ON
OFF
32
CP-950
Traditional Chinese Big5
OFF
OFF
ON
ON
ON
ON
33
CP-936
Simplified Chinese GBK
ON
OFF
ON
ON
ON
ON
34
CP-932
Japanese Shift-JIS
OFF
ON
ON
ON
ON
ON
35
CP-949
Korean
ON
ON
ON
ON
ON
ON
-33-
Chapter 3. BIOS Setup Utility
3-1. BIOS Setup Program
The motherboard supports a programmable firmware chip that can be updated using the provided utility described in the following. Use the BIOS Setup
program when you are installing a motherboard, reconfiguring your system, or prompted to “Run Setup”. This section explains how to configure your system
using this utility.
Even if you are not prompted to use the Setup program, you can still change the configuration of your computer in the future. For example, you can enable
the security password feature or change the power management settings. This requires you to reconfigure your system using the BIOS Setup program so that
the computer can recognize these changes and record them in the CMOS RAM of the firmware hub.
The firmware hub on the motherboard stores the Setup utility. When you start up the computer, the system provides you with the o pportunity to run this
program. Press <Del> during the Power-On-Self-Test (POST) to enter the Setup utility; otherwise, POST continues with its test routines.
If you wish to enter Setup after POST, restart the system by pressing <Ctrl+Alt+Delete>, or by pressing the reset button on t he system chassis. You can also
restart by turning the system off and then back on. Only do this as a last option if the first two fail.
The Setup program is designed to make it as easy to use as possible. Being a menu-driven program, it lets you scroll through the various sub-menus and
make your selections from the available options using the navigation keys.
-34-
3-1-1. Legend Box
The keys in the legend bar allow you to navigate through the various setup menus.
Key(s)
Function Description
F1
General help, only for Status Page Setup Menu and Option Page Setup Menu
Esc
Return to the main menu from a sub-menu or prompts you to quit the setup program
←, →
Move to the item in the left or right hand
↑, ↓
Move to previous or next item
Enter
Brings up a selection menu for the highlighted field
+ or PgUp
Moves the cursor to the first field
- or PgDn
Moves the cursor to the last field
F5
Loads the previous values
F6, F7
Loads the fail-safe / optimized defaults
F10
Saves changes and exits Setup
-35-
3-1-2. List Box
This box appears only in the opening screen. The box displays an initial list of configurable items in the menu you selected.
3-1-3. Sub-menu
Note that a right pointer symbol (▶) appears to the left of certain fields. This pointer indicates that you can display a sub-menu from this field. A sub-menu
contains additional options for a field parameter. To display a sub-menu, move the highlight to the field and press <Enter>.
The sub-menu appears. Use the legend keys to enter values and move from field to field within a sub-menu as you would within a menu.
Use the <Esc> key to return to the main menu.
Take some time to familiarize yourself with the legend keys and their corresponding functions.
Practice navigating through the various menus and submenus. If you accidentally make unwanted changes to any of the fields, press <F6> to load the failsafe default values. While moving around through the Setup program, note that explanations appear in the Item Specific Help window located to the right of
each menu. This window displays the help text for the currently highlighted field.
-36-
3-2. BIOS Menu Screen
When entering the BIOS, the following screen appears. The BIOS menu screen displays the items that allow you to make changes to the system configuration.
To access the menu items, press the up/down/right/left arrow key on the keyboard until the desired item is highlighted, then press [Enter] to open the
specific menu.
-37-
3-3. Standard CMOS Features
The “Standard CMOS Features” screen gives you an overview of the basic system.
-38-
Date [Day, xx/xx/xxxx]
The date format is <day>, <month>, <date>, <year>.
Time [xx:xx:xx]
The time format is <hour>, <minute>, <second>, based on the 24-hour clock.
IDE Channel 0/1 Master/Slave
IDE HDD Auto-Detection : [Press Enter] to select this option for automatic device detection.
IDE Device Setup
[Auto] : Automatically detects IDE devices during POST
[None] : Select this when no IDE device is used. The system will skip the auto-detection setup to make system start up faster.
[Manual] : User can manually input the correct settings.
- Access Mode : The options are CHS/LBA/Large/Auto
- Capacity : Capacity of currently installed hard disk
- Cylinder : Number of cylinders
- Head : Number of heads
- Precomp : Write precomp
- Landing Zone : Landing zone
- Sector : Number of sectors
Video
This category detects the type of adapter used for the primary monitor that must match your video display card and monitor.
- EGA/VGA : Enhanced Graphics Adapter/Video Graphics Array. For EGA, VGA, SVGA or PGA monitor adapters.
- CGA 40 : Color Graphics Adapter, power up in 40 column mode.
- CGA 80 : Color Graphics Adapter, power up in 80 column mode.
-39-
Halt On
Sets the system to halt on errors according to the system functions specified in each option.
Configuration options : [All Errors] [No Errors] [All, But Keyboard]
Memory
This category displays base memory, extended memory, and total memory detected during POS (Power On Self Test)
-40-
3-4. Advanced BIOS Features
The “Advanced BIOS Features” screen appears when choosing the “Advanced BIOS Features” item from the “Initial Setup Screen” m enu. It allows the user to
configure the RX945G according to their particular requirements. Below are some major items that are provided in the Advanced BIOS Features screen. A
quick booting function is provided for your convenience. Simply enable the Quick Booting item to reduce the system‟s booting time.
-41-
[Hard Disk Boot Priority]
Set hard disk boot device priority.
-42-
CH0 S.
Primary SATA channel with Master Device. It will show the device model / type when a SATA HDD or CD ROM is connected.
Bootable Add-in Cards
"Bootable add-in cards" is an item on the HDD boot priority list.
Virus Warning
Enables or disables the virus warning.
Item
Description
Enable
Activates automatically when the system boots up causing a warning message to
appear when anything attempts to access the boot sector or hard disk partition
table.
Disable
No warning message will appear when anything attempts to access the boot
sector or hard disk partition table.
CPU L1 & L2 Cache
Enabling this feature speeds up memory access.
Item
Description
Enable
Enable cache
Disable
Disable cache
Hyper Threading Technology
System will detect automatically and show up when you installed the Intel® Pentium® 4 processor with HT Technology. Set to “Enabled” for faster system
performance.
-43-
Quick Power On Self Test (POST)
This allows the system to skip certain tests to speed up the boot-up procedure.
Item
Description
Enable
Enable quick POST
Disable
Normal POST
First / Second / Third Boot Device
The BIOS tries to load the OS from the devices in the sequence set here. The options are:
Item
Description
LS120
LS120 Device
HDD
Hard Disk Device
CDROM
CDROM Device
ZIP100
ZIP-100 Device
USB-FDD
USB Floppy Device
USB-ZIP
USB ZIP Device
USB-CDROM
USB CDROM Device
USB-HDD
USB Hard Disk Device
Legacy LAN
Network Device
Disabled
Disabled any boot device
-44-
Boot Other Device
Use this to boot another device. The options are “Enabled” and “Disabled”.
Boot Up NumLock Status
Sets the boot up NumLock status. The options are “On” and “Off”.
Item
Description
On
Enable NumLock
Off
Disable NumLock
Gate A20 Option
Item
Description
Normal
A pin in the keyboard controller controls GateA20
Fast
Lets chipset control GateA20 (Default)
Security Option
This category determines whether a password is required when the system boots up or only when entering setup. The options are:
Item
Description
System
The system will not boot, and access to Setup will be denied, if the correct
password is not entered at the prompt.
Setup
The system will boot, but access to Setup will be denied, if the correct password is
not entered at the prompt.
-45-
APIC Mode
This setting allows you to enable the APIC mode. The choices are “Disabled” or “Enabled.”
MPS Version Control for OS
This option is only valid for multiprocessor motherboards as it specifies the version of the Multiprocessor Specification (MPS) that the motherboard will use.
The MPS is a specification by which PC manufacturers design and build Intel architecture systems with two or more processors.
MPS 1.1 was the original specification. MPS version 1.4 adds extended configuration tables for improved support of multiple PCI bus configurations and
greater expandability in the future. In addition, MPS 1.4 introduces support for a secondary PCI bus without requiring a PCI bridge.
Small Logo (EPA) Show
This item allows you to enable/disable the small EPA logo being shown on screen at during the POST.
Item
Description
Enabled
EPA Logo is shown
Disabled
EPA logo is hidden
-46-
3-5. Advanced Chipset Features
-47-
DRAM Timing Selectable
When set to “BySPD”, the DRAM timing parameters are set according to DRAM SPD (Serial Presence Detect). When disabled, one can manually set the DRAM
timing parameters through the sub items below. Set to “BySPD” if unsure about this feature.
CAS Latency Time
Controls the latency between the SDRAM Read command and the time data actually becomes available.
DRAM RAS# to CAS# Delay
Controls the latency between the DDR SDRAM active command and the read/write command.
DRAM RAS# Precharge
Controls the idle clocks after issuing a precharge command to the DDRSDRAM.
Precharge Delay (tRAS)
This setting determines the timing delay for DRAM precharge.
System Memory Frequency
Allows user to choose different frequencies of memory module.
System BIOS Cacheable
Selecting “Enabled” allows caching of the system BIOS ROM at F0000h- FFFFFh, resulting in better system performance. However, a system error may occur if
data is written to this area of memory by any programs.
Video BIOS Cacheable
Selecting “Enabled” allows caching of the video BIOS ROM at F0000h-FFFFFh, resulting in better video performance. However, a system error may occur if data
is written to this area of memory by any programs.
-48-
Memory Hole At 15M-16M
Enabling this feature reserves 15 MB to 16 MB memory address space for ISA expansion cards that specifically require this setting. This makes memory from
15 MB and up unavailable to the system. Expansion cards can only access memory up to 16 MB. The default setting is “Disabled”.
On-Chip Frame Buffer Size
The On-Chip Frame Buffer Size can be set to 1MB or 8MB. This memory is shared with the system memory.
DVMT Mode
Use this field to select the type of memory to allocate as video memory. Configuration options: “Fixed”, “DVMT” and “BOTH”.
DVMT/FIXED Memory Size
Specify the size of DVMT/system memory to allocate for video memory.
Boot Display
The options are: [Auto], [CRT], [LFP], [CRT+LFP], [DVI]
Panel Number
The options are: [640x480 18bit] [800x600 18bit] [1024x768 18bit] [1280x1024 18bit/2]
[1400x1050 18bit/2] [1400x1050 18bit/2] [1600x1200 18bit/2] [1280x768 18bit]
[1680x1050 18bit/2] [1920x1200 18bit/2] [1024x768 18bit/2] [1024x768 24bit] [1024x768 18bit]
[1280x800 24bit] [1280x600 18bit] [2048x1536 18bit/2]
-49-
3-6. Integrated Peripherals
Use this menu to specify settings for integrated peripherals.
-50-
[OnChip IDE Device]
-51-
IDE HDD Block Mode
Block mode is also called block transfer, multiple commands, or multiple sector read/write. If your IDE hard drive supports block mode (which is the case for
most newer hard drives), select “Enabled” for automatic detection of the optimal number of block read/writes per sector that the drive can support.
IDE DMA Transfer Access
To Enable/Disable the IDE DMA transfer access.
OnChip Primary PCI IDE
The integrated peripheral controller contains an IDE interface with support for two IDE channels. Select “Enabled” to activate each channel separately.
IDE Primary/Secondary Master/ Slave PIO
The four IDE PIO fields allow you to set a PIO mode (0-4) for each of the four IDE devices that the onboard IDE interface supports. Modes 0 through 4
provide successively increased performance. In Auto mode, the system automatically determines the best mode for each device.
IDE Primary/Secondary Master/ Slave UDMA
Ultra DMA/33 implementation is possible only if your IDE hard drive supports it and the operating environment includes a DMA driver (Windows 95 OSR2 or
a third-party IDE bus master driver). If your hard drive and system software both support Ultra DMA/33, select Auto to enable BIOS support .
On-Chip Secondary PCI IDE
Enables the secondary IDE channel.
On-Chip Serial ATA
The chipset contains a SATA IDE interface with support for two IDE channels. Select Enabled to activate the primary IDE interface (Channel0). Select Disabled
to deactivate this interface. The options are: [Disabled], [Auto], [Combined Mode], [SATA Only].
-52-
[Onboard Device]
Azalia Audio Select
Select [Disabled] if you do not want to use Azalia audio. Configuration options: [Auto], [Disabled]
-53-
[SuperIO Device]
Onboard Serial Port 1/2
The configuration options are “3F8/IRQ4”, “2F8/IRQ3”, “3E8/IRQ4”, “2E8/IRQ3”, and “Disabled” for the on-board serial connector.
-54-
PWRON After PWR-Fail
This item allows you to choose whether you want to power on the system after power failure. Configuration options: [Off], [On], [Former-Sts].
Onboard Lan1/2 Boot ROM
Configuration options: [Enable], [Disable].
Watch Dog Timer Select
This option allows you to configure the watch dog timer. Configuration options: [Disabled], [10], [20], [30], [40] Sec. [1], [2], [4] Min.
Onboard Serial Port 3/4
Configuration options: [3F8/IRQ4], [2F8/IRQ3], [3E8/IRQ4], [2E8/IRQ3], and [Disabled] for the on-board serial connector.
-55-
[USB Device Setting]
USB 1.0 Controller
If your system has a USB controller installed on the system board, select “Enabled” to make it usable. Even if equipped, in case you wish to add a higher
performance controller, this feature should be disabled.
-56-
USB 2.0 Controller
Enables/Disables the USB 2.0 controller.
USB Keyboard Function
Select “Enabled” if your system contains a USB controller and you wish to use a USB keyboard.
USB Mouse Function
Select “Enabled” if your system contains a USB controller and you wish to use a USB mouse.
-57-
3-7. Power Management Setup
The power management setup controls the single board computer's “green” features for power saving.
-58-
ACPI Function
The choices are: [Enabled], [Disabled].
ACPI Suspend Type
This item allows you to set ACPI suspend type to [S1(POS)] (“Power On Suspend”), or [S3(STR)] (“Suspend To RAM”).
Run VGABIOS if S3 Resume
Select “Auto” to run „VGABIOS if S3 resume‟ automatically. Selecting “Yes” enables this function. Selecting “No” disables this function.
Power Management
There are three selections for Power Management, with each containing fixed parameter settings.
Item
Description
Min. Power Saving
Minimum power management, HDD Power Down = 15 Min
Max. Power Saving
Maximum power management, HDD Power Down = 1 Min
User Defined
Allows you to set each parameter individually. When not disabled, both
ranges are between 1 min. and 1 hr., with the exception of HDD Power
Down, which ranges from 1 min. to 15 min. and disable.
Video Off Method
Use this to select the method in which the video is turned off. Configuration options: [Blank Screen], [V/H SYNC+ Blank], and [DPMS].
Video Off In Suspend
While the system is in suspend mode, the video can be set to turn off automatically. Selecting “Yes” enables this function. Selecting “No” disables it.
-59-
Suspend Type
Select the suspend type. The choices are: [Stop Grant], [Pwron suspend].
MODEM Use IRQ
This determines the IRQ in which the MODEM can use. The choices are: [NA], [3], [4], [5], [7], [9], [10], [11].
Suspend Mode
Item
Description
Min. Power Saving
Minimum power management, HDD Power Down = 15 Min
Max. Power Saving
Maximum power management, HDD Power Down = 1 Min
User Defined
Allows you to set each parameter individually. When not disabled, both
ranges are between 1 min. and 1 hr., with the exception of HDD Power
Down, which ranges from 1 min. to 15 min. and disable.
HDD Power Down
Select “1-15 min.” to enable HDD Power Down mode between 1 to 15 min. Select “Disabled” to disable HDD Power Down function.
Soft-Off by PWR-BTTN
[Instant-Off] : Pushing the „soft power‟ button once switches the system off.
[Delay 4 sec] : Pushing and holding the „soft power‟ button for more than 4 seconds turns the system off. Pushing the button momentarily i.e. less than 4
seconds, switches the system to “Suspend” mode.
Wake-up by PCI Card
This will enable the system to wake up through PCI/LAN peripheral.
Configuration options: [Enabled] and [Disabled].
-60-
Power On by Ring
Select “Enabled” to power on the system from a soft off state by an input signal on the serial Ring Indicator (RI) line. The choices are: [Disabled], [Enabled].
USB KB Wake-up From S3
When “Enabled”, enter any key to wake up the system from S3 state.
The choices are: [Disabled], [Enabled].
Resume by Alarm
When “Enabled”, the date and time at which the RTC (real-time clock) alarm awakens the system from “Suspend” mode can be set.
-61-
3-8. PnP/PCI Configuration
-62-
Reset Configuration Data
“Disabled” is selected by default. If the system configuration is as such that the OS cannot boot due to a newly installed add-on card, select “Enabled” to reset
the Extended System Configuration Data (ESCD) when booting.
Resources Controlled By
Selecting “Manual” requires you to choose resources from the sub-menu.
“Auto(ESCD)” automatically configures all of the boot and Plug and Play devices (Windows 95 or above).
PCI/VGA Palette Snoop
This is set to “Disabled” by default.
Maximum Payload Size
This option allows you to set the maximum TLP payload size for PCI Express devices.
Configuration options: [128 bytes], [256 bytes], [512 bytes], [1024 bytes], [2048 bytes], and [4096 bytes].
-63-
3-9. PC Health Status
Shutdown Temperature
Defines the core system temperature at which the system will automatically shutdown to prevent damage by overheating
-64-
CPU Warning Temperature
Defines the processor temperature at which the system will emit a buzzing sound to alert the user.
Current SYSTEM Temperature
Displays the current system temperature.
Current CPU1 Temperature
Displays the current CPU temperature.
CPU Fan Speed
Displays the current CPU fan speed.
System Fan Speed
Displays the current system fan speed.
Vcore
Displays the current Vcore voltage value.
+12V
Displays the current +12V voltage value.
+5V
Displays the current +5V voltage value.
Smart Fan Function
System controls fan speed automatically according to temperature.
-65-
[Smart Fan Function]
Performance Mode : Fan is activated at 40°.
Optimal Mode : Fan is activated at 50°.
Silent Mode : Fan is activated at 60°.
-66-
3-10. Load Optimized Defaults
Use this menu to load the BIOS default values for minimal/stable system operation. Press <Y> to load the BIOS default values for the most stable, optimal
performance system operations.
-67-
3-11. Set Supervisor Password
Allows you to set a password for entering/altering setup menu options.
-68-
To change the password:
- Select “Set Supervisor Password” from the “Initial Setup Screen” menu and press <Enter>. The screen displays the following message:
- Enter your password.
- Press <Enter>.
- If the CMOS is working and the default password is being changed, the user will be asked for the password to be stored in the CMOS. Next, the following
message will appear:
“Please Confirm Your Password”
- Type the password once more and press <Enter>.
- After pressing <Enter>, the ROM password or current password (user-defined) that is stored in the CMOS can be changed.
Note:
- The password must be no longer than eight (8) characters.
- To enable the password setting feature, you must first select either “Setup” or “System” from the “Advanced BIOS Features” menu.
-69-
3-12. Set User Password
Allows you to set a password for entering/altering setup menu options.
-70-
To change the password:
- Select “Set User Password” from the “Initial Setup Screen” menu and press <Enter>. The screen displays the following message:
- Enter your password.
- Press <Enter>.
- If the CMOS is working and the default password is being changed, the user will be asked for the password to be stored in the CMOS. Next, the following
message will appear:
“Please Confirm Your Password”
- Type the password once more and press <Enter>.
- After pressing <Enter>, the ROM password or current password (user-defined) that is stored in the CMOS can be changed.
Note:
- The password must be no longer than eight (8) characters.
- To enable the password setting feature, you must first select either “Setup” or “System” from the “Advanced BIOS Features” menu.
-71-
3-13. Save & Exit Setup
When exiting, selecting “Save & Exit Setup” will record all changed entries to the CMOS memory of the chipset. Press “Y” to save values, or “N” to not save at
this time. Every time the system is switched on, the processor will check and compare these values to what it finds on the system. NB: This record is required
for the system to operate.
-72-
3-14. Exit Without Saving
Selecting this option when exiting allows you exit the setup program without recording any new values, or changing old ones, to the CMOS. To discard all
changes and exit the setup, press “Y”, otherwise press “N” to go back without discarding the changes you have made.
-73-
Chapter 4. Troubleshooting
4-1. Network Issues
Symptom
Corrective Procedure
Cannot access LAN
▪ Check if hub or switch is working correctly
▪ Check RJ45 cable connection
▪ Check LED Window LAN on/off
▪ Reinstall LAN card
▪ Connect LAN to motherboard after removing mother board and I/O LAN cable.
▪ Replace motherboard
4-2. MSR Issues
Symptom
Corrective Procedure
MSR does not respond
▪ Check cable after disassembling
▪ Reset by pressing SW1 of MSR board with cable connected
▪ Check motherboard connection and USB PCB status
▪ Replace MSR
-74-
4-3. USB Issues
Symptom
Corrective Procedure
USB port doesn‟t work
▪ Check Windows device manager
▪ Check keyboard and touch performance by pressing the Num Lock/Caps Lock
keys after removing external USB devices
▪ Check USB cable connection
▪ Replace motherboard
4-4. LCD Issues
Symptom
Corrective Procedure
LCD backlight doesn‟t work
▪ Check LCD cable connection
▪ Check inverter cable connection
▪ Replace inverter cable
▪ Replace LCD panel
4-5. Touch-screen Issues
Symptom
Corrective Procedure
Touch-screen doesn‟t detect touch operations
▪ Check touch-screen cable connection
▪ Check motherboard and LCD cable connection
▪ Dismantle monitor and check touch-controller connection
▪ Replace touch-controller
-75-
4-6. Power Issues
Symptom
Corrective Procedure
System switches off abruptly and system does not load
▪ Check motherboard cable connection
▪ Remove all external peripheral devices and check again
▪ Replace power supply unit
4-7. Booting Issues
Symptom
Corrective Procedure
Re-booting during system operating
▪ Check serial peripheral devices connection status
▪ Check USB peripheral devices connection status
▪ Check device manager
▪ Replace power supply unit and/or motherboard
4-8. Printer Issues
Symptom
Corrective Procedure
Printer won‟t operate
▪ Check printer power supply
▪ Perform printer self test by pressing printer Reset and Feed button
▪ Try resetting printer by pressing printer Reset button
▪ Check cable connections status
▪ Check printer cable
-76-
Chapter 5. Motherboard
5-1. Motherboard Layout
-77-
-78-
5-2. Clearing CMOS
This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can clear the CMOS memory of date, time, and system setup parameters by
erasing the CMOS RTC RAM data. The onboard button cell battery powers the RAM data in CMOS, which includes system setup information e.g. system
passwords.
To erase the RTC RAM:
1. Turn OFF the computer and unplug the power cord.
2. Remove the onboard battery.
3. Move the jumper cap from pins 1-2 (default) to pins 2-3. Keep the cap on pins 2-3 for 5~10 seconds, then move the cap back to pins 1-2.
4. Re-install the battery.
5. Plug in the power cord again and turn ON the computer.
6. Hold down the <Del> key during the boot process and enter BIOS setup to re-enter data.
Except when clearing the RTC RAM, never remove the cap on CLRTC jumper default position. Removing the cap will cause system boot failure.
-79-
5-3. Serial Port Power Jumper Settings
12V
RI
+5V
COM1 Port
COM2 Port
COM3 Port
COM4 Port
COM6 Port
COM5 Port
-80-
[COM6 Signal Level Select]
This jumper allows you to select COM6 TTL level for COMHD6.
Set COMP6SEL6 to pins 1-3 and pin 2-4 to select normal RS-232. Set COMP6SEL6 to pins 3-5 and 4-6 to select TTL level for COMHD6.
NORMAL RS-232
TTL LEVEL
5-4. STACON1
This jumper allows you to use SATA DOM on SATA1.
Set STACON1 to pins 2-3 to select GND. Set STACON1 to pins 1-2 to select +5V for SATA DOM.
+5V
-
GND
-81-
Chapter 6. Maintenance
6-1. Safety Warning
POSBANK will not be held responsible for repairs conducted via service providers other than those officially specified by the seller.
General Guidelines
1. Always disconnect the unit from the power outlet.
2. Disconnect all cables from the POS main unit before attempting reparation.
3. Keep all components in the static-proof packaging provided until ready for installation.
4. If the device still is not functioning after repair, please turn off the POS unit and contact the customer service center for a follow-up inspection.
5. We recommend that power supply unit (PSU) checks and monitor repairs
only
be performed at a certified service center.
-82-
[HDD Replacement]
1. Remove the 4 screws from the underside of main unit as shown above.
2. Remove cover from unit.
3. Remove screw from metal frame attached to HDD.
-83-
4. Disconnect cable connected to HDD.
5. Replace with new HDD and reassemble unit using the reverse procedure
of steps 1-4 as shown previously.
-84-
[Motherboard Replacement]
1. Remove screw from the underside of main unit as shown above.
2. Detach bottom-cover using hooks on both sides.
3. Remove the 4 screws from the area shown above.
-85-
4. Disconnect cable connected to the motherboard.
5. Replace with new motherboard and reassemble unit using the reverse
procedure of steps 1-4 as shown previously.
-86-
[Memory (RAM) Replacement]
1. First, remove motherboard as shown on P. 83.
2. Push fixtures on both sides outwards (as shown above) and remove the
memory from its slot.
3. Insert new memory in slot and press lightly to fix into place.
-87-
[SSD Replacement]
1. Remove screw from the underside of main unit as shown above.
2. Detach bottom-cover using hooks on both sides.
3. Disconnect cable connected to SSD and remove by pushing the SSD clip.
4. Replace with new SSD and reassemble unit using the reverse procedure
of steps 1-3 as shown previously.
-88-
[MSR Replacement]
1. Remove the 2 screws as shown above.
2. Disconnect cable connected to MSR.
3. Replace with new MSR and reassemble unit using the reverse procedure
of steps 1-2 as shown previously.
-89-
[Paper-Roll Replacement]
1. Press “Open” button on printer cover to open cover.
2. Install new roll of paper as shown above.
3. Slightly draw out end of the roll and close printer cover.
“Open” button
After closing the printer cover, ensure to press the
centre
of the
cover to ensure the paper is in contact with the roller
-90-
[Printer Replacement]
1. Remove the lever-screw at side of main unit as shown above.
2. Open printer cover and remove both screws from inside.
-91-
3. Pull printer upwards to unlock and detach from main unit.
4. Replace with new printer and reassemble unit using the reverse
procedure of steps 1-3 as shown previously.
-92-
6-2. Technical Specifications
[miniO Main Unit]
CPU
Intel Atom N270 1.6GHz processor
Chipset
Intel 945GSE+ICH7M
HDD
1GB SSD (HDD option)
Memory
DDR2 SODIMM x 1 slot (Default 1GB up to 2GB)
VGA
Intel 945GSE GMA950 Engine
Printer
2" thermal printer(24V) 200mm/sec max(Auto cutter)
Display
8.4" (800 x 600)
Internal I/O
Parallel
1 Port (reserved for internal printer)
USB
1 x touch screen, 1 x keyboard, 1 x MSR, 1 x I-Button reserved, 1 x SCR
RS-232
COM 4 reserved for VFD or 2nd display
COM 3 reserved for 2" mini printer
LVDS
Main display use
Mini PCIe
1 slot support
External I/O
USB
Side 1, Rear 2
RS-232
COM 1 ~ 2 with +5/12V power output on 9pin
LAN
GbE LAN
Cash drawer
1 x RJ11 , Cash drawer port
Optional
MSR
Comply with ISO 7811, Support 1& 2 & 3 track
SCR
IC card reader
Dallas
Dallas I-button reader
Keyboard
Mini standard keyboard or Programmable keyboard : 55 Key
-93-
VFD
Customer display LCD type (16 x 2) or VFD type (20 x 2) / pole type customer display
CF CARD
CF card reader
Power Supply
INPUT: 100-240V~,50/60Hz 1.5A OUTPUT: DC 24V 2.5A
Qualification
CE, FCC, KCC
OS Support
Windows CE 6.0 on SSD, Windows XP/XPE, POS Ready(WEPOS) on HDD, Linux
Dimension
325(mm) x 393(mm) x 176(mm)
-94-
[Integrated Printer]
Printing
Method
3" Jam-free Thermal line dot printing
Number of dots/line
576
Resolution (dots/mm)
8
Paper width (mm)
80
+0 -1
Printing width (mm)
72
Speed (mm/sec)max
170
Paper path
Curved
Detection
Head temperature
By thermistor
Platen position
By mechanical switch
Out of paper
By photo interrupter
Cutter home position
By photo interrupter
Power Supply(V)
Operation voltage (Vdd)
2.7 to 3.6 / 4.75 to 5.25
Operation voltage (Vp)
21.6 to 26.4
Peak current(A)
Head
2.61 (26.4V/144dots)
5.23 (26.4V/288dots)
Motor
0.44
Cutter
0.64
Auto cutter
Method
Slide type
Paper thickness (㎛)
54 to 80*1
-95-
Cutting type
Full cut/Partial cut (Leave center point)
Operating time (sec/cycle)max
Approx. 0.5
Cutting pitch (mm)min
10
Cut frequency(cut/min)max
30
Service life
Pulse activation
100 million
Abrasion resistance (km)
100*1
Life (cut)
700,000*1
Operating temperature(℃)
-10 to 50
Loading...