T-2000CK 1hp
Cyclone Extractor
Code 505087
AXMINSTER
SERIES
Trade
Index of Contents
2
Declaration of Conformity
Copied from CE Certificate
The undersigned N. Sifonios, authorised by
Meta International Co., Ltd No. 38-46, Ya Tan Road.,
Ta Ya Hsiang. Taichung Hisien, Taiwan, R.O.C.
Model Number: T-2000CK (DUST COLLECTOR)
Manufactured by Meta International Co., Ltd. is in
compliance with the standards determined in the
following Council Directive.
Low Voltage Directive: 2006/95/EC
EN 60204-1: 2006+A1: 2009
Warning
The symbols below advise that you follow
the correct safety procedures when using
this machine.
Fully read manual
and safety instructions
before use
Eye protection
should be worn
Ear protection
should be worn
HAZARD
Motor gets hot
Dust mask
should be worn
Page No:
Index of Contents 02
Declaration of Conformity 02
What’s Included 03-04-05
General Instructions for 230V Machines 06
Specific Safety for Dust Extractors 07
Specification 07
Assembly Instructions 07-08-09-10-11-12-13
Overview Description 14-15
Operating and Adjustments 16
Maintenance 17
Weekly LEV System Maintenance Log 18-19
LEV Testing 20
Parts Drawing/List 21-22-23
Wiring Diagram 24
Notes 25
What’s Included
3
Quantity Item Model Number
T-2000CK
1 No 1hp Cyclone Extractor (Code: 505087)
Part
1 No Motor Assembly 1
3 No Upper Leg Square Tubes 2
3 No Lower Leg Square Tubes 3
3 No Cross Support Brackets 4
3 No Leg Bracket Connectors 5
6 No Angled Brackets 6
1 No Extraction Drum 7
1 No Flexible Hose 8
1 No Bin 9
1 No Bin Cover 10
1 No Extraction Funnel 11
1 No Steel Ducting 12
1 No Inlet Moulding 13
1 No Air Filter Cartridge 14
1 No Shaker Paddle Operating Handle 15
1 No Manometer and Hose 16
1 No Bin Handle 17
1 No Steel Ducting 18
1 No Dust Bag Securing Clip 19
2 No Dust Bags 20
Part
4 No Bin Castor Wheels 21
3 No Castor Wheels 22
3 No Bin Lever Clamps with
Phillips Screws and Nuts 23
Bag Containing 24
12 No 12 UNC Screws a
12 No 5/16" Nuts b
8 No 1/4" Domed Head Nuts c
6 No M6 Washers d
6 No 5/16" Button Head Hex Bolts e
56 No 5/16" Button Head Bolts f
2 No 1/4" Phillips Screws g
6 No 1/4" Hex Bolts h
1 No 12 UNC Screw i
2 No Small Jubbile Clips j
2 No Large Jubbile Clips k
1 No 5mm Hex Key l
1 No 10-12mm Spanner m
Please read the Instruction Manual prior to using your new machine. As well as the operating procedures for your
new machine, there are numerous hints and tips to help you to use the machine safely and to maintain its efficiency
and prolong its life. There is also a detailed description of the parts of your Cyclone Extractor, which will enable you to
become familiar with terminology we will use in this manual. Keep this Instruction Manual readily accessible for any
others who may also be required to use the machine.
Continues Over...
1
What’s Included
4
3 4
5
6
2
7
11 12 13
14
8 9 10
What’s Included
5
15
16
17
18
19 20 21 22
24
23
a b
c d
e f g h i
j k l m
General Instruction for 230V Machines
6
These machines are supplied with a moulded 16 Amp
plug and 3 core power cable. Before using the machine,
inspect the cable and the plug to make sure that neither
are damaged. If any damage is visible, have the damaged
item inspected/repaired by a suitably qualified person.
If it is necessary to replace the plug, it is preferable to
use an ‘unbreakable’ type that will most resist damage.
Only use a 16 Amp plug, and make sure the cable clamp
is tightened securely. Fuse as required. If extension leads
are to be used, carry out the same safety checks on them,
and ensure that they are correctly rated to safely supply
the current that is required for your machine. Remember,
most machines or tools have handles or holding positions,
the power cable is not one of them.
Good Working Practices/Safety
Mains Powered Tools and Machines
Primary Precautions
Workplace/Environment
The following suggestions will enable you to observe
good working practices, keep yourself and fellow workers
safe and maintain your tools and equipment in good
working order.
WARNING!! KEEP TOOLS AND EQUIPMENT OUT
OF THE REACH OF YOUNG CHILDREN
KEEP THE WORK AREA AS UNCLUTTERED AS
IS PRACTICAL, THIS INCLUDES PERSONNEL
AS WELL AS MATERIAL.
UNDER NO CIRCUMSTANCES SHOULD
CHILDREN BE ALLOWED IN WORK AREAS.
The machine is not designed for use outside. Keep the
machine clean; it will enable you to more easily see any
damage that may have occurred. Clean the machine with
a damp soapy cloth if needs be, do not use any solvents or
cleaners, as these may cause damage to any plastic parts
or to the electrical components.
It is good practice to leave the machine unplugged until
work is about to commence, also make sure to unplug
the machine when it is not in use, or unattended. To
avoid inadvertent ‘start up’, if your machine is not fitted
with a NVR system, ensure the switch is always returned
to the OFF position. Once you are ready to commence
work, remove any tools, objects or items that could
inadvertently get ‘sucked up’ by the machine and place
safely out of the way. Re-connect the machine, ensuring
the power cable is not ‘snagged’ or routed where it could
be tripped over as you move about the workshop; it is
not too close to an unguarded heat source, or is laid over
or around a sharp edge. If the work you are carrying
out is liable to generate flying grit, dust or chips, wear
the appropriate safety clothing, goggles, gloves, masks
etc. If the work operation appears to be excessively
noisy, wear ear-defenders. If you wear your hair in a
long style, wearing a cap, safety helmet, hairnet, even a
sweatband, will minimise the possibility of your hair being
caught up in the rotating parts of the machine, likewise,
consideration should be given to the removal of rings
and wristwatches if these are liable to be a ‘snag’ hazard.
Consideration should also be given to non-slip footwear,
etc.
Do not use this machine if you are tired, your attention is
wandering or you are being subjected to distraction.
Do not use this machine within the designated safety
areas of flammable liquid stores or in areas where there
may be volatile gases. There are very expensive, very
specialised machines for working in these areas. Above
all, OBSERVE…. make sure you know what is happening
around you, and USE YOUR COMMON SENSE.
Specific Safety
for Dust Extractors
Do not use this machine as a vacuum cleaner, try to keep
the waste medium to wood by products.
Do not uplift workshop floor debris (stones, nails, screws,
paper etc., etc). Be aware that wood dust is an explosive
medium.
Do not allow any ‘naked light’ source to occur anywhere
near the machine. This includes cigarettes, matches, etc,
and do not place the machine near any unprotected light
bulbs, that could possibly get broken.
The suction force is generated by a high speed fan unit.
This has the potential to amputate fingers, grab loose
clothing (ties etc.,) and ‘bat’ large chips etc, at high
speeds. Keep all guarding in place, and if access to the fan
becomes necessary (due to blockage etc.,) disconnect
the machine from the mains supply and ensure the fan
has come to a complete stop before putting your hands
anywhere near to it.
If you are not using ‘clear’ extraction hose, periodically
remove the hose to check that the inlet to the machine
is not getting restricted. (The safety guard grill of the
inlet duct can be particularly irksome in this way, as long
strand shavings etc., can wrap around the grill fret.)
Specific Safety for Dust Extractors
7
Keep the particle filter clean. The machine relies on its
ability to ‘blow’ air through the filter, to generate good
suction. If the particle filter starts to clog, this reduces the
air flow and hence the machine becomes less efficient.
The particle filter can be cleaned, by removing the rear
filter cover and using a vacuum cleaner, clean the inside of
the filter.
Be aware that in dry air periods or areas, the movement of
the air through the machine can generate static electric
fields. These are not normally a problem as the machine
is bonded together via its construction and the whole is
earthed back through the electrical supply; problems can
occur with isolated items, such as stands or hosing that is
insulated from the ground.
• If possible, try to connect everything together
electrically, to eliminate static shocks.
• Use the integral metal coil in exible plastic hosing to
connect units together.
• Try to route the power cable and the hosing away from
busy walkways.
• Do not allow the inlet to become ‘dead ended’, or block
or restrict the outlet, this puts undue strain on the motor
and can lead to overheating.
NOTE: ALWAYS USE MANUFACTURERS WASTE BAGS WITH THIS MACHINE!
Model T-2000CK
Rating Trade
Power 0.75 kW (230V, 1ph)
Air Flow 1,100m³/hr
Noise Level 80 dB @ 3m
Filter Area 3.8m²
Filtration 1 micron
Particle Size 1 micron
Hose Diameter 150mm x 1, 100mm x 2
Overall L x W x H 1,300 x 1,100 x 1,560mm
Weight 71kg
Specification
Assembly Instructions
Please read through the section entitled Parts Identification and Description, this will enable you to more readily
identify those parts of the cyclone extractor.
Please note: some of this assembly procedure is best accomplished by two persons. Although
the tasks are not impossible, some of the items are heavy and awkward, and a mishandling
error could cause injury. Please think about what you are doing, your capabilities and your
personal safety. We have added the ‘two person symbol’ to any operation that we recommend
should be a two person task.
Unpack all the boxes and check all the components listed in the “What’s Included” section. If any parts or components
are missing, please contact our Customer Services Department using the procedures and telephone numbers listed in
our catalogue.
Please note: on occasions the packing list is not strictly adhered to. Please check all the boxes, packets
etc. to make sure that all the parts have been accounted for.
PLEASE RECYCLE ANY UNWANTED PACKAGING RESPONSIBLY!
Assembly Instructions
8
Having unpacked the boxes, put all components where
they are readily to hand. Locate the motor assemby (1),
the upper and lower leg square tubes (2-3), cross support
brackets (4), leg connectors (5), angle brackets (6), 5/16"
button head Hex bolts (f) and 5/16" nuts (b).
Step 1 Place the motor assembly (1) upside down on
the floor, locate the three upper leg square tubes (2),
Note: one of them should have fixings for mounting
the manometer (16). Line up the holes in the angled
end of this square tube with the pre-drilled holes in the
mounting plate next to the fan assembly outlet and
secure using two button head bolts (f) and 5mm Hex
key (l), see figs 01-02-03. Repeat for the remaining leg
supports. Repeat for the remaining square tubes (2).
Step 2 Locate the three leg bracket connectors (5) and
the lower leg square tubes (3), slide one of the connectors
down into one of the leg tubes (3) and line up the lower
two holes in the connector (5) with holes in the leg tube
and secure in place with button head bolts (f), see fig 04.
Repeat the process as described above for the remaining
leg tubes (3).
Fig 02-03
f
2
1
Fig 04
5
3
NOTE: ONLY LIGHTLY TIGHTEN THE BOLT AT
THIS STAGE!
Step 3 Insert the square tubes (3 and 5) down into the
ends of each lower square tubes (2) and line up the holes,
see figs 5-6.
Fig 05
5
f
Fig 06
3
3
2
Fig 01
Mounting plate for the upper
leg square tube (2 )with
fixings for manometer (16)
Holes for attaching
angle brackets (6)
Assembly Instructions
9
Step 4 Locate the angle brackets (6), place the bracket flat
against the upper square tube (2), line up the pre-drilled
holes and secure with two button head bolts (f), see fig
07. Repeat on the process for the opposite side and carry
on for the remaining legs.
Fig 07
Fig 08-09
Step 5 Locate the three cross support brackets (4), line up
the pre-drilled holes in one of the brackets with the holes
in two of the angle brackets (6), using four button head
bolts (f) and nuts (b) secure the cross support bracket
(4) in position. Repeat for the remaining two side of the
assembly. (see figs 08-09).
Step 6 Locate the three castor wheels (22), screw each
castor into the threaded holes on top of legs (3), using a
spanner tighen the nut at the base of each castor to lock
the assembly in position. (see figs 10-11).
Fig 10-11
2
6
4
b
f
Step 7 Locate the extraction drum (7) and the 12unc
Hex screws (a). Position the drum on top of the motor
assembly (1), there are arrow marker labels on each unit,
line up these labels and secure the drum (7) to the motor
assembly (1) using the Hex screws (a). (see fig 12-13)
Fig 12-13
22
Locking Nut
Arrow marker label
a
Step 8 Loosen clamping bolt/nut from the extention
funnel (11), remove the clamping ring and place safely
aside. Lower the wide end of the funnel (11) on top of
the drum (7) and line up the rims. Locate the clamping
ring you removed earlier, position the ring over the
rims and tighten the bolt/nut to lock both units (7-11)
together. (see figs 14-15).
Continues Over...
7
1
Assembly Instructions
10
Fig 14-15
11
Clamping ring
Rim
Step 9 Locate the bin cover (10), 1/4 " Hex bolts (h) and
1/4" domed head nuts (c). Place the bin cover (10) face
up, on top of the funnel assembly (11). Line up the arrow
marker labels and pre-drilled holes, place a Hex bolt (h)
down through one of the holes and lightly secure with
a domed head nut (c). (see figs 16-17) Repeat for the
remaining holes then fully tighten.
Fig 16-17
h
c
10
You will require the bin (9), bin castor wheels (21), bin
lever clamps with Phillips screws and nuts (23), bin handle
(17), 1/4" domed nuts (c), 1/4" Phillips screws (g), dust bag
(20), flexible hose (8) and large jubilee clips (k).
Step 10 Turn the bin (9) on its side and screw on the four
castor wheels (21) into the threaded holes to the base of
the bin and tighten the nuts using the supplied spanner
(m), see fig 18.
Fig 18
Step 11 Turn the bin (9) upright, locate the bin lever
clamps (23) remove the four nuts and screws to one of
the clamps and place safely aside. Line up the holes in the
bin lever clamp (23) with the four holes to the side of the
bin (9), (NOTE: make sure the lever clamp is the correct
way round), replace the screws and nuts you removed
earlier, securing the lever clamp in position. (see fig 19-20).
Repeat the process for the remaining clamps.
Fig 19-20
23
9
Assembly Instructions
11
Step 12 Turn the cyclone assembly upright on its wheels,
WARNING! THE MACHINE IS HEAVY
YOU ARE ADVISED TO SEEK HELP!
locate the flexible hose (8) and the two Jubilee clips (k).
Place a Jubilee clip over one end of the hose (8), introduce
the hose over the bins inlet manifold and tighten the
Jubilee clip, DON’T OVERTIGHTEN otherwise the hose
will split, see fig 21. Insert the other Jubilee clip over the
Fig 21
other end of the hose and introduce it over the outlet
manifold on the extraction funnel (11), secure in place,
see fig 22.
Fig 22
Step 13 Locate the bin handle (17), line up the holes with
the two pre-drilled holes in the bin (9) and secure in place
with 1/4" Phillips screws (g) and domed head nuts (c), see
figs 23-24.
Fig 23-24
8
k
k
11
9
17
c
Step 14 Locate the dust bag (20), open the bag and place
it inside the bin (9), see fig 25. (Make sure the bag is
tucked over the edge of the bin)
Fig 25
20
Step 15 Position the bin (9) beneath the bin cover (10),
line up the bin lever latches (23) with the hooks on the
bin cover (10), hook on the latches and press down the
lever handles to raise the bin against the cover, making a
tight seal, (see figs 26-27).
NOTE: you may need to adjust the nuts on lever
latches if the seal between the cover and bin
are not tight, see fig 27.
Fig 26-27
Latch
Hook
Latch adjusing nuts
Continues Over...
Assembly Instructions
12
You will require the steel ducting (12), steel ducting seal
(18), 5/16" button head Hex bolts (e), 5/16" button head
Hex bolt (f), air filter cartridge (14) and shaker paddle
handle (15).
Step 16 Locate steel ducting (12), insert the ducting seal
(18) into the square recess of the ducting (12), see fig 28.
Fig 28
Place the square end of the ducting (12) over the outlet of
the motor assembly (1), secure in place using eight button
head Hex bolts (f), see figs 29-30.
Fig 29-30
12
12
f
Step 17 Locate the six button head Hex bolts (e), offer
up the cut out slot in the air filter cartridge (14) with the
rectangular outlet of the ducting (12). Line up the
pre-drilled holes and secure both units together using
six button head Hex bolts (e), see figs 31-32.
Fig 31-32
e
14
1
18
Step 18 Locate shaker paddle hande (15), loosen the grub
screw to the side of the machined aperture using the
supplied Hex key (l), slide the handle (15) onto the shaker
paddle drive shaft, on top of the air filter (14) and nip up
the grub screw to lock the handle in place, see figs 33-34.
Fig 33-34
Machined aperture
Grub screw
l
Step 19 Locate the remaining dust bag (20) and dust bag
securing clip (19). Open up the bag and rap it around the
base of the air filter (14), see 35. Remove the securing clip
(19) from its packaging, rap it around the filter (14) and
dust bag (20) and secure the dust bag in place, see figs
35-36-37.
Fig 35-36-37
20
14
19
15
Assembly Instructions
13
Step 20 Locate the manometer and hose (16), remove the
fixings from the lower leg square tube (2), offer up the two
pre-drilled holes in the manometer (16) with the holes in
the leg (2), replace the fixing and tighten. (see fig 38)
NOTE: MAKE SURE THE MANOMETER (16) IS
MOUNTED TO THE LEFT SIDE OF THE LEG!
Fig 38
Step 21 Place a small Jubilee (j) over one end of the
hose and insert it over the small outlet manifold on the
extraction funnel (11) and nip up tight, see fig 39.
Fig 39
WARNING! DONT OVERTIGHTEN THE JUBILEE
CLIP TO PREVENT THE HOSE FROM SPLITTING!
j
Hose
2
16
Step 22 Connect the other end of the hose to the inlet
manifold to the rear of the manometer (16), see fig 40.
Fig 40
j
Step 23 Locate the inlet moulding (13) and the 12unc
screw (i). Insert the moulding over the outlet manifold
on the extraction funnel (11), line up the pre-drilled
holes and secure using the 12unc screw and Phillips
screw driver, see fig 41.
Fig 41
13
11
i
Step 24 Finally go round and make sure all fixings are
tight and secure.
CONNECT THE POWER SUPPLY TO THE MAINS
AND SWITCH ON!
DISCONNECT THE POWER SUPPLY FROM THE
MAINS!
Wait until it’s up to full speed and check for signs of
vibration, if all is well.. switch off and wait until the
extractor has come to a compleate stop!
If the extractor fails to start up or any other strang
noises apart from vibraction sounds, contact the
“Technical Sales” for support.
Phone: 03332 406406
Email: technical@axminster.co.uk
Testing the extractor
WARNING!! MAKE SURE CHILDREN ARE KEPT
AWAY FROM THE CYCLONE EXTRACTOR WHILE
IN OPERATION
NOTE: ALWAYS TURN ON/OFF THE EXTRACTOR
BY THE NVR CONTROL SWITCH NOT THE MAINS
SWITCH!
Overview Description
14
1 Motor Assembly
2 Upper Leg Square Tube
3 Lower Leg Square Tube
4 Cross Support Bracket
7 Extraction Drum
8 Flexible Hose
9 Bin
10 Bin Cover
11 Extraction Funnel
12 Steel Ducting
13 Inlet Moulding
14 Air Filter Cartridge
15 Shaker Paddle Handle
16 Manometer
17 Bin Handle
19 Dust Bag Securing Clip
20 Dust Bag
21 Bin Castor Wheel
22 Castor Wheel
23 Bin Lever Clamp
1
12
16
15
14
19
20
8
22
21
23
9
17
10
3
11
4
13
2
7
NVR switch assembly
Overview Description
15
NVR switch assembly with (O) indicating (OFF) and (I)
indicating (ON). For emergencies “SLAP” the shroud
down to “STOP” the machine.
Bin lever clamp (23), pull up the handle to release bin.
23
Off
On
Inlet moulding (13), with lid Shaker handle lever (15), move this handle from side to
side to remove dust build up from inside the air filter (14).
13
15
Air filter (14), shaker paddle assembly Bin (9) “FULL” indicator, empty the bin’s contents
when it reaches the “FULL” mark.
Shaker paddle drive shaft
inner filter
14
Operating and Adjustments
16
ALWAYS TURN ON/OFF THE EXTRACTOR BY THE
NVR CONTROL SWITCH NOT THE MAINS SWITCH
Switching ON/OFF
Levelling the Extractor
Manometer
The manometer is used to monitor the air flow in the
ducting system. When you first use your extractor it is
recommended you mark on the ‘manometer’ the pressure
the extractor it running at. To do this, follow the
instructions below.
Note: the reading can vary depending on the size of
the ducting system.
1. Connect your cyclone extractor to the ducting system.
Fig 43
2. Start up the extractor by pressing the ‘green’ button on
the NVR switch assembly and check the reading on the
manometer.
3. Using a marker or sticky label mark the reading on the
manometer, (see figure 43). This is to confirm that every
time you switch on you know what the reading will be.
If you find the reading has increased there could be a
blockage in the ducting system or extractor unit, check
the following:
• Check the rear lter for signs of buildup of sawdust
and clean with a vacuum cleaner
• Check the hoses for blockages
• Check the bin bag and empty if full
If the reading has decreased, check the following:
•Check the hoses are secure, ‘NOT LOOSE’ which will
lead to air leakages
• Check hoses for splits and cracks
• Check “Blastgates” that are not in use are shut
WARNING!! BEFORE CARRYING OUT ANY
MAINTENANCE DISCONNECT THE CYCLONE
EXTRACTOR FROM THE MAINS SUPPLY!
For all of our accessories please see our catalogue or
contact us on:
Phone: 03332 406406
Extraction Accessories
If you find the extractor castors (22), is not in contact with
the floor you can adjust them by loosening the locking
nut beneath the castors pivot assembly then rotate each
castor in turn, in or out until correct then retighten the
locking nut to secure the castors (22) in position, see fig
42.
Fig 42
indicating mark
Maintenance
17
Daily
• Empty the collection bag before it overows, wear a
dust mask whilst removing and emptying the bag.
Weekly
• Check the inlet and outlet ducts and remove any
accumulated sawdust.
•Check the inlet hoses for splits and cracks, repair as
necessary.
• Check the dust collection bag for wear and tear,
especially around the neck at the Jubilee clip. If wear
WARNING! BEFORE CARRYING OUT ANY
MAINTENANCE DISCONNECT THE CYCLONE
EXTRACTOR FROM THE MAINS SUPPLY
WARNING! KEEP CHILDREN AWAY FROM WORK
AREA
After a period of time dust, sawdust and shavings can
build-up causing blockages and reduced suction
performance. Follow the maintenance instructions below
to keep your extractor working at peak performance.
Basic Maintenance
WARNING! ALWAYS WEAR A DUST MASK
WARNING! ALWAYS WEAR EYE PROTECTION
Fig 43
or fraying is occurring, replace the bag.
• Check the motor for dust, sawdust, shavings etc,
build up. If this has occurred, clean with a vacuum
cleaner.
• Move the shaker paddle handle (15) back and forth
to remove any built up dust and debris from inside the
filter.
Monthly
• Remove the dust bag securing clip (19) and remove
dust bag (20), using a vacuum cleaner, clean inside the
filter.
Weekly LEV System Maintenance Log
18
Week
Date
Checked by
Check all ducting
for physical damage
Check inlets, clear any
obstructions if found
Check operation of all
blastgate controls
Check filter(s) for damage
and condition
Check filter shakers
(if fitted) and clean filters
Check waste collector(s)
for damage and condition
Empty waste collectors
if necessary
Comments
1
2
3
4
5
6
7
8
9
10
11
12
REMOVE AND
CLEAN FILTERS
13
14
15
16
17
18
19
20
21
22
23
24
REMOVE AND
CLEAN FILTERS
25
26
27
28
29
30
31
32
33
34
Weekly LEV System Maintenance Log
19
Week
Date
Checked by
Check all ducting
for physical damage
Check inlets, clear any
obstructions if found
Check operation of all
blastgate controls
Check filter(s) for damage
and condition
Check filter shakers
(if fitted) and clean filters
Check waste collector(s)
for damage and condition
Empty waste collectors
if necessary
Comments
35
36
REMOVE AND
CLEAN FILTERS
37
38
39
40
41
42
43
44
45
46
47
48
49
REMOVE AND
CLEAN FILTERS
50
51
52
Nearly 14 months it is now a legal requirement to have
your system tested and certified
53
54
55
56
57
58
59
60
LEV Testing
20
Why should I bother with LEV?
The law says you must control the risks from these
substances (the Control of Substances Hazardous to
Health (COSHH) Regulations). Installing LEV may help
you to do this.
For more information about other ways of eliminating or
reducing airborne contamination at work look, at HSE’s
COSHH website, hse.gov.uk/coshh.
A guide to local exhaust ventilation (LEV)
Ref Code: HSG258
The book above provides guidance on the supply of local
exhaust ventilation (LEV) equipment. It describes the
principles and good practice of deciding on, designing,
commissioning and testing cost-effective LEV.
The guidance is written for the suppliers of LEV goods
and
services, but will also be helpful for employers and
managers in medium-sized businesses, and trade union
and employee safety representatives. All of these groups
need to work together to provide, maintain and use
effective LEV and to reduce exposure from inhalation of
hazardous substances.
The book contains information about the roles and
legal responsibilities of suppliers and of their clients as
employers; competence; principles of good design
practice for effective LEV hoods and their classification;
ducts, air movers, air cleaners; and system documentation
with checking and maintenance schedules, and the
marking of defective equipment.
It also includes guidance on the specification of LEV; the
supplier’s quotation; commissioning; zone marking; the
user manual and logbook; testing and hood labels.
Health and Safety Executive
Parts Drawing/List
21
Parts Drawing/List
22
NO. Description Specification Q’TY
1 Hose Clamp 1-1/2” 2
2 Flange Nut 1/4” 8
3 Nut 1/4” 2
4 Spring Washer 1/4” 1
5 Lock Nut M4 12
6 Steel Clamp Dia. 370 1
7 Power Cord W/ Plug 1
8 Nut 5/16” 4
9 Square Pad 1
10 PC Board 1
11 Leg Connecting Bracket 3
12 Drum Lid 1
13 Round Clamp Dia. 347 1
14 Round Collector 1
15 Outlet Connector 1
16 Motor 1
17 Packing 1
18 Lower Leg 3
19 Upper Leg 2
20 Main Housing 1
21 Brace I (Middle) 1
22 Brace J (Short) 1
23 Brace L (Long) 1
24 Gage Fixing Ring 1
25 Gage Fixing Plate 1
26 Dust Drum 1
27 Brace Connecting Bracket 6
28 N Type Handle 1
29 Reducing Collector 1
30 Canister 1 Microm (Dia. 370* 300) 1
31 Spindle 1
32 Inlet 6” x 4” x 2 1
33 Bearing Fixing Plate 1
34 Fixing Plate 2
35 Lower Fixing Plate 1
36 Flapper New 3
37 Bearing 1
38 Aluminium Impeller 12-3/4” 1
Parts Drawing/List
23
39 Lock Nut M10 1
40 PE Bag Big(101) 1
41 PE Bag Small 1
42 Phil. HD Screw 1/4” x 5/8” 2
43 Phil. HD Screw M5 x 10mm 3
44 Phil. HD Screw M6 x 10mm 1
45 Flange Screw 1/4” x 1/2” 6
46 Button HD Screw 1/4” x 1/2” 2
47 Phil. HD Screw M6 x 12 6
48 Hex Bolt 1/4” x 1” 4
49 Hex Bolt 1/4” x 2-1/2” 3
50 Set Screw M6* 16 1
51 Button HD Screw 5/16”* 1/2” 56
52 Cap Screw M6 x 30 (LH) 1
53 Key 1
54 Washer 1/4” x 13 3
55 Washer 1/4” x 18 11
56 Rivent 4-2 8
57 Hose Clamp 3/4” 2
58 Drum Clamp Hook 3
59 Negative Gauge 1
60 Hose 1-1/2”* 1.8M 1
61 Clear Hose 1/2” 1
62 Impeller Washer 1
63 Motor packing 4
64 Phil. HD Flange Screw 3/16” x 3/8” 1
65 Cap Screw 3/16” x 3/8” 12
66 Phil. HD Screw M4 x 8 20
67 Phil. HD Screw M5 x 15 4
68 Handle 1
69 Castor 3” x 3/8” 3
70 Ball Castor 2” *5/16” 4
71 Upper Leg with two additioanal holes 1
72 Nut 3/8” 3
73 Nut M5 4
74 Switch 1
75 HD Screw 5/16” x 3/4” 6
76 Flange Nut 1/4” 3
77 Flange Nut 12
78 Drum Clamp 3
Wiring Diagram
24
Notes
25
Axminster Tools & Machinery Ltd
Weycroft Avenue, Axminster, Devon EX13 5PH
axminster.co.uk
Please dispose of packaging for the product in a responsible manner. It is suitable for recycling. Help to
protect the environment, take the packaging to the local recycling centre and place into the appropriate
recycling bin.
Do not dispose of electric tools together with household waste material. In observance of European
Directive 2002/96/EC on waste electrical and electronic equipment and itsimplementation in accordance
with national law, electric tools that have reached the end of their life must be collected separately and
returned to an environmentally compatible recycling facility.
Only for EU countries
Free Three Year Guarantee on Axminster Hobby, Trade and Industrial Series woodworking and
engineering machines, Axminster Air compressors and Air Tools, and bench top grinders - no
registration necessary just proof of purchase.
We will repair or replace at our discretion and will collect only from a UK mainland address,
irrespective of the original delivery address.
The Guarantee assumes that you have bought the correct machine for the required operation, in
accordance with our guidelines; have operated and maintained it in accordance with the instruction
manual; and that all cutting machines will be used with a blade which is sharp and serviceable at all
times. It does not cover consumable items purchased with the original product, including original
blades or abrasives.
The Axminster guarantee is available on
Hobby, Trade, Industrial, Engineer, Air Tools & Axcnc Technology Series machines
It’s probably the most comprehensive FREE guarantee ever- buy with confidence from Axminster!
So sure are we of the quality, we cover all parts and labour free of charge for three years!
• Look for the icon and put your trust in Axminster
• No registration necessary - just keep your proof of purchase
• Optional Service Plan for Industrial Series machinery
AXMINSTER
SERIES
Hobby
Great value & easy-to-use,
perfect for use at home
Quality, precision machines
for the workshop or education
Precision CNC machines for
industry and education
AXMINSTER
SERIES
Trade
Solid, reliable machines
designed for daily use
Small machines for the home
engineer
Top performers with class leading features and
build quality for use in busy workshops
Compressors and tools for home or
workshop use; durable and great value
Normal wear and tear; misuse, abuse and neglec t are excluded and the machine should not have been
modified in any way. Please do not attempt to service the produc t without first contacting us; we are
happy to guide you but failure to do so may invalidate the guarantee.
The Guarantee is transferable from owner to owner in the first three years but you must have original
proof of purchase. Should we need to replace a machine in the first three years the guarantee will still
continue to be effective from the original purchase date.
Full Terms and Conditions can be found at axminster.co.uk/terms
This guarantee does not affect your statutory rights.
For more information visit axminster.co.uk/3years
Loading...