700098
CSC500C
Woodturning
Chuck Set
Axminster Reference No: CSC500C
User Manual
www.axminster.co.uk
01
Index of Contents...
www.axminster.co.uk
Page No.
Safety Protection Symbols
SAFETY!!
!
The symbols shown on the cover of this
manual advise that you wear the correct
safety protection when using this machine.
E
y
e
P
r
o
t
e
c
t
i
o
n
S
a
f
e
t
y
H
e
l
m
e
t
P
r
o
t
e
c
t
i
v
e
G
l
o
v
e
s
S
a
f
e
t
y
F
o
o
t
w
e
a
r
R
e
s
p
i
r
a
t
o
r
S
a
f
e
t
y
V
i
s
o
r
R
e
a
d
M
a
n
u
a
l
T
w
o
M
a
n
A
s
s
e
m
b
l
y
E
a
r
D
e
f
e
n
d
e
r
s
D
u
s
t
M
a
s
k
Warranty...
Thank you for purchasing one of Axminster’s growing family of woodworking products. The
CSC500C Chuck Set is engineered and manufactured to the highest quality standards. You
will find this product an essential accessory to your workshop.
This product is warranted against defects in material and workmanship for a period of one
years for all components. This warranty applies to the original purchaser of the product and
is limited to the repair and/or replacement of the product, or its parts at the discretion of
Axminster Power Tool Centre. Excluded are parts which have been misused, abused, altered,
or consumed by normal operation of the chuck. Also excluded are direct or consequential
damages to persons, or properties, or materials is as proof of purchase and must be
referenced to authorize any warranty repair. Call your Axminster dealer for proper
authorization.
Index of Contents......................................................................................................................................... 1
Warranty........................................................................................................................................................1
Safety Instructions for Chuck Systems....................................................................................................... 2
What’s in the Box.....................................…………...................................................................................2-3
Chuck System Description..........................................................................................................4
Jaw Capacity Chart..................................................................................................................... 5
Installing Jaws to Chuck............................................................................................................. 5
Mounting the Adapter.................................................................................................................. 5
Mounting the Chuck to Your Lathe............................................................................................. 6
Operating the chuck....................................................................................................................6
Chuck Gripping Depth.................................................................................................................6
Lathe Speeds...............................................................................................................................6
02
Safety Instructions for Chuck Systems...
FREEPHONE 0800 371822
The following suggestions will enable you to observe good working
practices, keep yourself and fellow workers safe and maintain your
tools and equipment in good working order.
Good Working Practices/Safety
WARNING!!
!
KEEP TOOLS AND EQUIPMENT OUT
OF THE REACH OF YOUNG CHILDREN
1. Do not wear gloves or loose clothing when turning.
2. Do not wrap any strip sandpaper or clothing around your hands or fingers when
sanding or turning.
3. Use proper eye protection when turning.
4. Check your wood for splits, weakness or cracking prior to mounting on the
chuck.
5. Confirm that the wood is tightly gripped before turning your chuck under power.
6. Rotate the chuck manually prior to starting your lathe to confirm proper
clearance.
7. Always check and re-lighten after any problem or catch.
8. Use appropriate speeds as referenced in instructions.
9. Always turn with sharp lathe chisels.
10. Capture fine particles from the air with a dust collector.
11. Keep clean and lubricate with at light oil as needed.
What’s in the Box...
Model Number: CSC500C
A CSC500C Chuck set (pre threaded for 1" x 8tpi)
B 1. Set (4 piece) of #2 round jaws (shipped pre-mounted to chuck)
C 1. Hex wrench
D 2. Tightening levers
E 1. Set (4 piece) step jaws
F 1. Set (4 piece) extended pin jaws
G 1. Screw chuck
H 1. 3/4" x 16tpi adapter
Instruction Manual
A
D
E
F
H
G
B
C
03
What’s in the Box...
www.axminster.co.uk
04
Chuck System Description...
FREEPHONE 0800 371822
A. Main body: designed to hold all jaws as an assembly.
B. Carrier: to which the top jaws are each attached with one or two hex screws. (#4 jaw has
toungue which must mate with groove)
C.Jaws: attached to the carrier, used for gripping the wood piece to be turned.
D. Socket hex screws: attach jaws to chuck (2 per jaw/1 per pin jaw).
E. Lever tightening holes: insert and turn tightening levers to secure grip.
A
B
C
D
E
(Shown with two round jaws installed)
05
Jaw Capacity Chart...
www.axminster.co.uk
Installing Jaws to Chuck...
Mounting the Adapter...
Select the appropriate jaw for your project. Place the selected jaw on top of the carrier,
matching the number stamped on the main body to the number on each individual jaw. Using
the provided hex wrench, firmly tighten the jaw down onto the surface of the carrier with the
hex screws. Repeat this step for the remaining three jaws.
1. Wipe the inside of the threads and the outside of the adapter to insure both surfaces are
clean.
2. Use the furnished 3/4"xl6tpi adapter if necessary.
3. Hold the chuck in your hand, screw and tighten the adapter into the bottom threaded
portion of the chuck.
Adapter
Chuck
06
Mounting the Chuck to Your Lathe...
FREEPHONE 0800 371822
Screw the completed assembly onto your lathe. The chuck should go on effortlessly with no
binding. Screw the chuck all the way until the adapter face contacts the shoulder of the
lathe spindle. Lock the spindle, slightly unscrew the chuck and give it a firm spin. This will
snap the chuck firmly in place.
Your chuck has two movable discs. Each disc has 4 holes to accommodate the tightening
levers. Insert a tightening lever into one of the holes on each level. Rotate the tightening
levers away or toward each other to close or open the chuck. Clockwise tightens,
counter-clockwise loosens the jaws.
When turning a bowl, for safety reasons, allow a minimum amount of wood for the chuck to
grab while turning.
1. Cavity base (inside grip) - for a 2" diameter base, minimum hole depth is 3/16".
2. Spigot base (outside grip) - for a 2" diameter base minimum grip is 3/16".
Turning: 500-I500rpm
Sanding & Polishing: 1500-2500rpm
Make sure your wood is properly aligned and balanced
when mounted or re-mounted.
Use slower speeds for larger work.
Operating the Chuck...
Chuck Gripping Depth...
Lathe Speeds...
700098
www.axminster.co.uk
Axminster Devon EX13 5PH UK
FREEPHONE 0800 371822
Axminster Reference No: CSC500C
CSC500C Woodturning Chuck Set
Loading...