AT254TS
Table Saw & Additional Tables
AT&M: 06/09/2018
BOOK REF : 007287
Code 104501
Original Instructions
Cert No: HW110LGE-30
Axminster Tools & Machinery Ltd
Axminster Devon
EX13 5PH UK
axminster.co.uk
Type Table saw
Model AT254TS
conforms to the machinery example for which the
EC Type-Examination Certificate No BM50416470
has been issued by Harvey Industries Co., Ltd.
at: 01 Building, No.68 Suyuan Road, Jiangning Economic & Technological Development Zone,
Nanjing 211100 China
and complies with the relevant essential health and safety requirements.
2006/42/EC
06/42/EC - Annex I/05.2006
EN 60204-1:2006+A1+AC
EN 1870-19:2013
declares that the machinery described:-
This machine complies with the following directives:
EU Declaration of Conformity
Signed
Andrew Parkhouse
Operations Director
Da te: 29/08/2018
3. Machine Description
3.1 Technical parameters
Item HW110LGE-30 HW110LGE-50
Product Dimensions
weight
260Kg （approx.）
length/width/height(mm) 1582x1100x1016 2090x1100x1016
foot print(length/width) 508x508
Electrical: switch
magnetic with thermal overload protection
Motor
type TEFC capacitor start induction
horsepower/voltage/phase/amps 3HP-230V-1PH 12.8A
speed/cycle 2850 RPM/50HZ
power transfer Triple V-belt Drive
blade information
maximum blade diameter 250mm
riving knife/spreader thickness 2.5mm
required blade body thickness 1.8-2.4mm
required blade kerf thickness 2.6-3.2mm
maximum width of Dado 15mm
blade tilt left 0-45°
arbor size 30mm
arbor speed 4150 RPM(50Hz)
arbor bearings sealed and permanently lubricated
cutting capacities
maximum depth of cut at 90° 70mm
maximum depth of cut at 45° 50mm
maximum rip to right of blade-standard 750mm 1250mm
maximum rip to left of blade 305mm
Table informations
floor to table height 860mm
main table--length/width/thickness 512x685x48mm
distance front of table to center of blade 440mm
distance front of table to blade of maximum cut 310mm
miter gauge information
miter gauge slot type T-slot
miter gauge slot type-- width/height
19.05 ×9.525mm
other information paint power coated
dust port size 100mm
3.5 Noise
3.5.1 Reference standards
The measurements of noise emission were
conducted according to the EN ISO 11202 for the
determination of sound pressure level at the
operation positions. When the measured sound
pressure levels at the operation positions exceed
85dB(A), the measurements of sound power levels
were conducted according to EN ISO 3746.
3.5.2 Operating conditions
The operating conditions for noise measurement
comply with Annex A of ISO 7960:1995.
3.5.3 Testing results
NO LOAD LOAD
LWA 101.3 104.1
LPA
Position A 84.7 88.5
Position B 86.1 89.1
Position C 77.0 79.8
Associated uncertainty
K = 4 dB
Note: Background noise of measurement
surrounding is 65.0dB (A).
The figures quoted are emission levels and are not
necessarily safe working levels. Whilst there is a
correlation between the emission and exposure
levels, this cannot be used reliably to determine
whether or not further precautions are required.
Factors that influence the actual level of exposure of
the workforce include the characteristics of the work
room, the other sources of noise etc. i.e. the number
of machines and other adjacent processes. Also the
permissible exposure level can vary from country to
country. This information, however, will enable the
user of the machine to make a better evaluation of
the hazard and risk.”
4. Safety Regulations
4.1 General Safety Instructions
1. KNOW YOUR MACHINE.
Read and understand the owners manual and labels
affixed to the machine. Learn its application and
limitations as well as its specific potential hazards;
2.GROUND THE MACHINE.
In the event of the electrical short, grounding
reduces the risk of electrical short;
3. KEEP GUARDS IN PLACE.
Keep in good working order, properly adjusted and
aligned;
4. REMOVE ADJUSTING KEYS AND
WRENCHES.
Form habit of checking to see that keys and
adjusting wrenches are removed from machine
before turning it on;
5. KEEP WORK AREA CLEAN.
Cluttered areas and benches invite accidents. Make
sure the floor is clean and not slippery due to wax
and sawdust build-up;
6. AVOID DANGEROUS ENVIRONMENT.
Don’t use machines in damp or wet locations or
expose them to rain. Keep work area well lit and
provide adequate surrounding work space;
7. KEEPCHILDREN AWAY.
All visitors should be kept a safe distance from work
area;
8. MAKE WORKSHOP CHILD-PROOF.
With padlocks, master switches or by removing
starter keys;
9. USE PROPER SPEED.
A machine will do a better and safer job when
operated at the proper speed;
10. USE RIGHT MACHINE.
Don’t force the machine or the attachment to do a
job for which it was not designed;
11. WEAR PROPER APPAREL.
Do not wear loose clothing, gloves, neckties or
jewelry (rings, watch) because they could get caught
in moving parts. Non-slip footwear is recommended.
Wear protective hair covering to contain long hair.
Roll up long sleeves above the elbows;
12. DON’T OVER REACH.
Keep proper footing and balance at all times;
13. MAINTAIN MACHINE WITH CARE.
Keep tools sharp and clean for best and safest
performance. Follow instructions for lubricating and
changing accessories;
14. DISCONNECT MACHINES.
Before servicing, when changing accessories or
attachments;
15. AVOID ACCIDENTAL STARTING.
Make sure the switch is in the ‘’OFF’ ’position before
plugging in;
16. USE RECOMMENDED ACCESSORIES.
Consult the manual for recommended accessories.
Follow the instructions that accompany the
accessories. The use of improper accessories may
cause hazards;
17. NEVER STAND ON MACHINE.
Serious injury could occur if the machine tips
over .Do not store materials such that it is necessary
to stand on the machine to reach them;
18. CHECK DAMAGED PARTS.
Before further use of the machine, a guard or other
parts that are damaged should be carefully checked
to ensure that they will operate properly and perform
their intended function. Check for alignment of
moving parts, breakage of parts, mounting, and any
other conditions that may affect its operation. A
guard or other parts that are damaged should be
properly repaired or replaced;
19. NEVER LEAVE MACHINE RUNNING
UNATTENDED.
Turn power ‘’OFF’’. Don’t leave any machine
running until it comes to a complete stop;
20. LIGHTING SHALL BE PROVIDED.
A dequate general or localised lighting shall be
provided;
4.2 Specific Safety Instructions for
Sliding Table Saw
1. ALWAYS USE A GUARD.
Always use a guard, splitter and anti-kickback
fingers on all “thru-sawing” operations. Thru-sawing
operations are those when the blade cuts
completely through the work piece as in ripping or
crosscutting.;
2. ALWAYS HOLD THE WORK.
Always hold the work firmly against the miter gauge
or fence;
3. ALWAYS USE A PUSHSTICK OR PUSH
BLOCKS.
Push blocks or push sticks shall be used when
cutting small workpieces and in circumstances
where it is necessary to push the workpiece against
the fence;
4.NEVER.
Never perform any operations “free-hand” which
means using your hands to support or guide the
work piece. Always use either the fence or the miter
gauge to position and guide the work piece;
5.NEVER.
Never stand or have any part of your body in line
with the path of the saw blade;
6.NEVER REACH BEHIND.
Never reach behind or over the cutting tool with
either hand for any reason;
7. MOVE THE RIP FENCE.
Move the rip fence out of the way when crosscutting;
8. DIRECTION OF FEED.
Feed work into the blade against the direction of
rotation;
9. NEVER.
Never use the fence as a cut-off gauge when you
are cross-cutting;
10. NEVER.
Never attempt to free a stalled saw blade without
first turning the saw OFF;
11. PROVIDE ADEQUATE SUPPORT.
Fig.11: checking fence parallelism
Note:
It's permissible for the back of the fence
to pivot outward not more than 1⁄64" from being
parallel to the blade. This creates a slightly
larger opening between the fence and the blade,
at the rear of the blade, to reduce the risk of
workpiece binding or burning as it is fed
through the cut. Many woodworkers
intentionally set up their fence in this manner.
Keep this in mind before adjusting your fence.
D, Install the fence scale(see Fig.12)
Fig.12 Aligning rail tape with scale pointer.
Slide the fence up against the saw blade, and lock it
in place;
place the front rail tape scale on the fence tube,
make sure it is parallel with the tube, and the“0” end
is directly under the red line on the pointer window
as shown; lightly mark the “0” location on the tube
with a pencil, then remove the fence; peel the tape
and carefully align the “0” mark on the scale with the
pencil mark you made;
If you make a mistake, loosen the screws on the
point window, slide the fence against the blade,
adjust the pointer window , so the red line on the
window is over the “0” mark on the tape, then
secure the screws;
5.4.6 Install the switch
install the magnetic switch onto the bottom left hand
side of the front rail using two M6-1x 12 hex bolts,
6mm lock washers, and 6mmflat washers, as shown
in Fig.13
Fig.13: switch install
5.4.7 Install the blade
A. Remove blade guard assembly & table insert.
B. raise the arbor all the way up and set the blade
angle at 0º.
C. remove the arbor nut and arbor flange from the
arbor, slide on the included 10" saw blade, making
sure the teeth face the front of the saw, then install
the arbor flange and arbor nut onto the blade.
D. put on a pair of heavy leather gloves and use the
included arbor wrenches to tighten the arbor nut
(turn clockwise to tighten), as shown in Fig.14
Fig.14: Install the blade
5.4.8 install the blade guard and riving
knife
A. reinstall the insert, slide the knurled knob out (see
Fig.15) and rotate it forward so it engages the upper
bracket.
Fig.15:Knurled knob used
B. slide the blade guard spreader all the way down
into the block, then rotate the knurled knob so it
disengages the bracket and the locking pin engages
the hole in the center of the spreader.
C. give the spreader an upward tug to verify that it is
locked the blade guard, when properly installed,
look like Fig, 16
Fig.16: Blade guard installed.
D. place a straightedge against the blade and the
spreader. When properly aligned, the
spreader/riving knife will be in the "alignment zone,"
shown in Fig.17 , and will be parallel with the blade.
Fig.17: alignment zone
After changing a saw blade, always check that the
Riving knife or Blade Guard is correctly set!
1. riving knives shall be manufactured from steel
with an ultimate tensile strength of 580 N mm-2 or of
a comparable material, have flat sides (within 0,1
mm per 100 mm) and shall have a thickness less
than the width of cut (kerf) and at least 0,2mm
greater than the saw blade plate. As Fig.18
Fig.18
electric power to this machine, in order to protect
people against electrical shock due to indirect shock
Wiring:
Finish electrical connection according to the
electrical drawings.
The wirings on the spot should refer to the
requirements of Clause 13 (Wring practices) of EN
60204-1:2006.
Checking:
After finishing wiring on the spot, check the following
items at least:
Check the wirings of machine.
Check the direction of motors and change wiring if
necessary.
Check the components for defects, such as
loosening or damage.
Check the functions of safety devices
ELECTRICAL CONNECTIONS
6.3 Aligning Table T-slot Parallel With
Blade
1,The table T-slot must be aligned parallel with the
blade. Using a combination square (A) as Fig.24,
measure the distance from the back edge of the
blade to the table T-slot. Pivot blade forward 180º
and remeasure the distance using the exact same
point on the blade. The difference between both
measurements must be less than 0.2mm.
2. If an adjustment is necessary, loosen the screws
(B) as Fig.25 which fix to the table, make the
needed adjustment until both measurements are
equal or less than 0.2mm. and retighten the screws
.
Fig.24
Fig.25:Adjust Trunnions to Align Blade and Miter
Slot
6.4 Adjusting 45 and 90 Degree
Positive Stops
The blade tilting mechanism of your saw is equipped
with a positive stop at 45 and 90 degrees. To check
and adjust these positive stops, proceed as follows:
1. Raise the saw blade to its maximum height.
2. Set the blade at 90 degrees to the table by turning
the blade tilting hand wheel counterclockwise as far
as it will go.
3. Place a square on the table and check to see if
the blade is at a perfect 90 degree angle to the
table.
4. If the blade is not at 90 degrees loosen lock nut (A)
As Fig.26 and turn stop ring (B) in or out. The stop
ring (B) should stop against the front trunnion
bracket when the blade is at 90 degrees to the table.
Recheck and adjust further if necessary. Retighten
lock nut (A).
Fig.26: Adjust 90 degrees
5. If the 45 degree postive stop is not set properly,
turn the same hand wheel clockwise as far as it will
go and follow the same procedure using lock nut (C)
As Fig.27 and stop ring (D). The stop bolt (D) should
stop against the front trunnion bracket when the
blade is at 45 degrees to the table. Recheck and
adjust further if necessary. Retighten lock nut (C).
8. Maintenance
This table saw requires very little maintenance other
than minor lubrication and cleaning. The following
sections detail what will need to be done in order to
assure continued operation of your saw.
LUBRICATION
The table saw has sealed lubricated bearings in the
motor housing and the arbor assembly, they will not
require any additional lubrication. Use a wire brush
to clean off the worm gears and trunnions and apply
a white lithium grease to keep them lubricated
CLEANING
Cleaning the Model is relatively easy. Vacuum
excess wood chips and sawdust, and wipe off the
remaining dust with a dry cloth. If any resin has built
up, use a resin dissolving cleaner to remove it.
After cleaning, treat all unpainted cast iron and steel
with a non-staining lubricant.
Occasionally it will become necessary to clean the
internal parts with more than a vacuum. To do this,
remove the table top and clean the internal parts
with resin/pitch dissolver or mineral spirits and a stiff
wire brush or steel wool.
Make sure the internal workings are dry before
using the saw again, so that wood dust will not
accumulate. If any essential lubrication is removed
during cleaning, re-lubricate those areas.
CHANGING BELTS
WARNING: MAKE SURE THE POWER CORD IS
DISCONNECTED FROM THE POWER SOURCE!
1. Lower the blade completely, then open the motor
access cover.
2. Loosen the hex nuts that secure the motor (see
Fig.33 ) and raise the motor fully to remove tension
on the V-belts. Roll the V-belts off of the arbor and
motor pulleys.
3. While continuing to raise the motor, install a new
matching set of V-belts onto the pulleys, lower the
motor to tension the V-belts, then tighten the hex
nuts.
4. Close the motor access cover.
Fig.33
9. Trouble Shouting Guide
PROBLEM SOLUTION
SAW WILL NOT START
1. Saw not plugged in. 1. Plug in saw.
2. Fuse blown or circuit breaker tripped. 2. Replace fuse or reset circuit breaker.
3. Cord damaged. 3. Have cord replaced by a certified electrician.
OVERLOAD KICKS OUT FREQUENTLY
1. Extension cord too light or too long. 1. Replace with adequate size cord
2. Feeding stock too fast. 2. Feed stock more slowly.
3. Blade in poor condition (dull, warped, gummed). 3. Clean or replace blade.
4. Blade binding due to misaligned rip fence.
4. Check and adjust the rip fence. See rip fence
instructions.
5. Blade binding due to warped wood. 5. Select another piece of wood.
6. Low house current. 6. Contact your electrical company.
DOES NOT MAKE ACCURATE 45 AND 90 RIP
CUTS
1. Positive stop(s) not adjusted properly. 1. Check blade with square and adjust positive stop.
2. Tilt angle pointer not set properly. 2. Check blade with square and adjust pointer to zero.
MATERIAL PINCHES BLADE WHEN RIPPING
1. Rip fence not aligned with blade. 1. Check and adjust rip fence.
2. Warped wood. 2. Select another piece of wood.
MATERIAL BINDS ON SPLITTER
1. Splitter not aligned correctly with blade kerf. 1. Check and align splitter with blade kerf.
SAW MAKES UNSATISFACTORY CUTS
1. Dull blade. 1. Replace blade.
2. Blade mounted backwards. 2.Turn blade around.
3. Gum or pitch on blade. 3. Remove blade and clean with terpentine and steel wool.
4. Incorrect blade for work being done. 4. Change the blade.
5. Gum or pitch on table causing erratic feed. 5. Clean the table with turpentine and steel wool.
BLADE DOES NOT COME UP TO SPEED
1. Extension cord too light or too long. 1. Replace with adequate size extension cord.
2. Low house current. 2. Contact your electric company.
3. Motor not wired for correct voltage. 3. Refer to motor and /or nameplate.
MACHINE VIBRATES EXCESSIVELY
1. Table not mounted securely to cabinet stand. 1. Tighten all mounting hardware.
2. Stand is on uneven floor. 2. Reposition on flat level surface.
3. Damaged saw blade. 3. Replace blade.
4. Bad V-belt(s). 4. Replace V-belt(s).
5. V-belts not tensioned properly. 5. Adjust V-belt tension.
6. Bent pulley. 6. Replace pulley.
7. Improper motor mounting. 7. Check and adjust motor mounting.
8. Loose hardware. 8. Tighten all nuts, bolts and set screws.
BLADE DOES NOT RAISE OR TILT FREELY
1. Sawdust or dirt in raising or tilting mechanisms. 1. Brush or blow out loose dust or dirt.
10. Parts List
Table Saw Body Breakdown
Trunnion Assembly Breakdown
Trunnion Assembly Parts List
REF#
DERIPTION QTY
REF#
DERIPTION QTY
201 handwheel lock 2
272 hex bolt M10x45 1
202 handwheel 2
273 lock washer 10 1
203 set screw M5x12 2
274 flat washer 10 2
204 point 1 1
275 arbor nut 1
205 set screw M5x6 1
276 arbor flange 1
206 point 2 1
277 set screw M5x12 2
207 cap screw M6*12 1
278 arbor 1
208 lock washer 6 1
279 key 5x30 1
209 flat washer 6 1
280 bearing 6005-2Z 2
210 nut 6 4
281 collar blade arbor 1
211 point bracket 1
282 Belt pulley 1
212 pan HD screw M5*25 2
283 collar blade arbor 1
213 plate 1
284 tighten collar 1
214 pan HD screw M8*30 6
285 cap screw M5*16 3
215 lock washer 8 9
286 flat washer 5 5
216 lock pin 4
287 flat washer 5 3
217 KEY 2
288 lock nut M16*1.5 1
218 angle worm shaft 1
289 high shaft 1
219 set collar 2
290 bull gear 1
220 set screw M6x8 4
291 orientation bar 1
221 wave lock washer 2
292 roll pin 5 x 30 2
222 copper backing 4
293 cap screw M5*25 2
223 worm 2
294 gear 1
224 set screw M6x12 2
295 gear sleeve 1
225 FRONT TRUNNION 1
296 big washer 1
226 cap screw M10*30 2
297 pan HD screw M10*45 1
227 flat washer 10 2
298 lock nut 10*1.5 1
228 lock washer 10 2
299 sleeve 1
229 nut M10 2
2001 knurled knob 1
230 cap screw M6*25 3
2002 spring 1
231 washer 1
2003 pin 1
232 cap screw M8*30 1
2004 bracket 1
233 plate gear 1
2005 set screw M6x12 4
234 back bracket 1
2006 lock washer 6 3
235 left bracket 1
2007 limit coller 3
236 right bracket 1
2008 splitter tighten clip 1
237 square HD bolt 2
2009 cap screw M6*30 3
238 flat washer 8 6
2101 belt 3
239 nut M8 8
2102 motor pulley 1
240 adjust screw 2
2103 set screw M5x12 2
241 set screw M8x8 1
2104 key 1
242 Compression spring 1
2105 motor 1
243 ball 1
2106 pin 1
244 lock nut M18 1
2107 roll pin 4 X 28 1
245 high shaft 1
2108 hex bolt M12x110 1
246 hex bolt M8x30 1
2109 flat washer 12 2
247 flange casting sleeve 2
2110 lock washer 12 1
248 hex bolt M8x35 1
2111 nut M12 1
249 handwheel handle 2
2112 motor bracket 1
250 trunnion 1
2113 set screw M8x12 2
270 key 6x45 1
2114 set screw M8x30 1
271 geared bearing housing
1
2115 nut M8 1
Blade Guard Breakdown
Blade Guard Parts List
REF# DERIPTION QTY REF#
DERIPTION QTY
371 splitter 1
375 phlp HD screw M6-1×25 1
372 left guard 1
376
lock washer 6 1
373 right guard 1
377
lock washer 10 1
374 cap screw M10x30 1
378 riving knife 1
Fence Breakdown
Fence Parts List
REF#
DERIPTION QTY REF#
DERIPTION QTY
501 cover 1 514 hex bolt M10-1.5x45 1
504 glide pad 2 515 lock nut M10-1.5 1
505
fence scale window
1 516 cam foot 1
521 1 517 magnet 1
506 set screw M12-1.75x15 4 518 cam 1
507 phlp hd screw M5-0.8x10 2 519 fence lock knob 1
508 lock washer 5 2 520 set screw M12-1.75x30 1
509 indicator 1 523 knob 3
510 special locking nut M12 5 524 teflon washer 3
511 set screw 2 525 guide bolt 3
512 hex bolt M6-1x40 1 526 fence face 1
513 lock nut M6-1 1 527 fence body 1
30″Rail & Extension Table Breakdown
30″Rail & Extension Table Parts List
REF#
DERIPTION QTY REF#
DERIPTION QTY
601 guide tube insert 2 608 hex bolt 5/16-18x1-1/2 2
602 guide tube 1 609 lock washer 8 12
603 scale 1 610 flat washer 8 22
604 front rail 1 611 rear rail 1
605 cap screw M6-1x16 3 612 hex bolt M8-1.25x40 10
606 lock washer 6 3 613 nut M8-1.25 10
607 flat washer 6 3 635 extension table 1
50″Rail & Extension Table Breakdown
50″Rail & Extension Table Parts List
REF#
DERIPTION QTY REF#
DERIPTION QTY
601 tube cover 2 622
foot
2
605 cap screw M6*16 5 624 phlp HD screw M8-1.25×40 6
606 lock washer 6 5 628
rear rail
1
607 flat washer 6 5 629
tube
1
608 hex bolt 5/16-18x1-1/2 2 630
scale
1
609 lock washer 8 18 631
front rail
1
610 flat washer 8 34 634 extension table 1
612 hex bolt M8x40 12 639
leg
2
613 nut 8 16
Switch Breakdown
Switch Parts List
REF#
DERIPTION QTY REF#
DERIPTION QTY
701A switch 1 711 lock washer 5 2
701D cable 1 712 flat washer 5 2
701E cable 1 713 chain 1
704 Switch bracket 1 714
Perforated pin
1
706 hex bolt M6x12 2 715
1
707 lock washer 6 3 716 strain relief 1
708 flat washer 6 3 717 rivet nut M5x12 4
709 Phillips screw M6x12 1 718 flat washer 5 4
710 phlp HD screw M5-.8×16 2 719 cap screw M5*20 4
1. Foreword
This instruction manual only for the table saw equipped with ST1400 & RT100.
The content includes: Product configuration and model, space requirements, the installation
of switch box and the use of the guide rail.
2. Product configuration list
Model
Options
Type
HW110WS
HW110WSE
HW110S-S
HW110SE-S
HW110WS-S
HW110WSE-S
Table
saw
110S
/
/ ● / / /
110SE
/ / / ● /
/
HW110LG
●
/ / / ● /
HW110LGE
/ ● / / /
●
Sliding table--
ST1400
● ● ● ● ●
●
Router table--RT100
●
●
Can't
install
Can't
install
/
/
Rail
WS-30
● ● ● ● ●
●
WS-50
Optional
Optional
Optional
Optional
Optional
Optional
NOTE：
Each table saw & attachments are equipped with independent instruction。
3. Space Requirements
Before your setup, you must insure the interspace between the machine and wall at least
800mm.
3.1 Model :HW110S-S , HW110WS-S
Fig.1
3.2 Model:HW110WS
Fig.2
4. Change the installation position of switch
When install the sliding table, you must
change the installation position of the
switch, you can install the magnetic
switch onto the bottom of the sliding
table with three sets hex bolts, as
shown in Fig.3
M6-1x 12 hex bolts……..3
6mm lock washers...……3
6mm flat washers……….3
Fig.3
5. About Rail
Due to the installation of the sliding table, we provide the short guide, the explosion diagram
and parts list of short guide, please see attachment file.
NOTE:
If the fence rails on your saw prevent is as Fig.4, you need to cut off the left ends of
the rails, as Fig.4 point;
(or re-mount the rails farther to the right, which may also require you to drill new
holes in your table and cut small notches into your rails for access to t-slots in your
saw’s table as Fig.5)
Next, you may need to re-mount the power switch to a new location, as Fig.3;
、
Fig.4 Fig.5
Attachment file：
WS-30″Short Rail Breakdown
WS-30″Short Rail Parts List
REF#
DERIPTION
QTY
REF#
DERIPTION
QTY
601
tube cover
2 608
hex bolt 5/16-18x1-1/2
2
602W
S
tube（30")
1 609
lock washer 8
8
603
scale（30")
1 610
flat washer 8
14
604W
S
front rail（30")
1
611W
S
rear rail（30")
1
605
cap screw M6*16
3 612
hex bolt M8x40
6
606
lock washer 6
3 613
nut 8
6
607
flat washer 6
3
WS-50″Short Rail Breakdown
WS-50″Short Rail Parts List
REF#
DERIPTION
QTY
REF#
DERIPTION
QTY
601
tube cover
2 610
flat washer 8
14
630
scale（50")
1 612
hex bolt M8x40
6
605
cap screw M6*16
3 613
nut 8
6
606
lock washer 6
3 628WS
rear rail（50")
1
607
flat washer 6
3 629WS
tube（50")
1
608
hex bolt 5/16-18x1-1/2
2 631WS
front rail（50")
1
609
lock washer 8
8
Axminster Tools & Machinery Ltd
Axminster Devon EX13 5PH
axminster.co.uk
The packaging is suitable for recycling.
Please dispose of it in a responsible manner.
Do not dispose of electric tools together with household waste material.
By law they must be collected and recycled separately.
EU Countries Only
The Axminster guarantee is available on
Craft, Trade, Engineer, Air Tools & CNC Technology Series machines
Buy with confidence from Axminster!
So sure are we of the quality, we cover all parts and labour free of charge for three years!
For more information visit axminster.co.uk/3years
Loading...