Axminster Tool Centre,
Unit 10 Weycroft Avenue, Axminster, Devon EX13 5PH
www.axminster.co.uk
AT1628VS Variable
Speed Wood Lathe
Code: 502703
Index of Contents
2
Index of Contents 02
Declaration of Conformity 02
What’s Included 03
Optional Accessories 03
General Instructions for 230V Machines 04
Specific Safety Instructions for Woodturning Lathes 05
Specifications 06
Assembly Instructions 6-10
Lathe Assembly 6-7
Lathe Stand Assembly 7-8
Lathe Extension Assembly 1 and 2 8-9
Illustration and Description 10-11
Operating Instructions 12-14
Rotating the Headstock 12
Removing the Faceplate 12
Indexing Facility 13
Removing the Drive Centre 13
Changing the Belt Speed 13-14
Maintenance 14
Parts Breakdown/List 15-16-17-18-19-20-21
Wiring Diagram 22
Notes 23
Declaration of Conformity
Copied from CE Certificate
The undersigned, authorised by Calvin Chon
Manufactured by Kingcraft Machinery Company
Limited/NO.26, Gong Yeh 12 Rd., Da-Li City, Taichung
County, Taiwan., manufacturer, declares that the
machine described hereafter:
WOOD TURNING LATHE
manufactured byKingcraft Machinery Company
Limited., is in compliance with the standards
determined in the following Council Directive.
• EN ISO 12100-1: 2003 + A1: 2009
• EN ISO 12100-2: 2003 + A1: 2009
• EN ISO 1412-1: 2007
• EN 60204-1: 2006 + A1: 2009
• EN 61000-6-2: 2005
• EN 61000-6-4: 2007
Warning
The symbols below advise that you follow
the correct safety procedures when using
this machine.
Fully read manual
and safety instructions
before use
Eye protection
should be worn
Ear protection
should be worn
Two Man
Assembly
Dust mask
should be worn
Please read the Instruction Manual prior to using
your new machine; as well as the operating
procedures for your new machine, there are
numerous hints and tips to help you to use the
machine safely and to maintain its efficiency and
prolong its life. Keep this Instruction Manual readily
accessible for any others who may also be required to
use the machine.
Model Number: 1417-1430-1443-1643-1417INV-1430INV-
1443INV-1643INV-1628INV-4224B-1642VS
3
Quantity Item Part Model Number
1628INV
1 No Variable Speed Wood Lathe A
1 No Spanner B
1 No Push Rod C
1 No Spindle Lock Pin D
1 No Motor Plate Handle E
1 No Instruction Manual
Quantity Item Part Code Number
1 No Lathe Extension H 502704
4 No 3/8” x 1 3/4” Hex Bolts & 8 No 3/8” Washers
1 No Tool Rest Extension I
2 No Lathe Stand F 502705
8 No 3/8" x 11/2" Bolts & 16 No 3/8" Washers
4 No Feet G
What’s Included
B
C
D
E
F
G
I
H
Optional Accessories
General Instructions for 230V Machines
4
Good Working Practices/Safety
The following suggestions will enable you to observe
good working practices, keep yourself and fellow
workers safe and maintain your tools and equipment
in good working order.
WARNING!! KEEP TOOLS AND
EQUIPMENT OUT OF THE REACH
OF YOUNG CHILDREN
Keep the work area as uncluttered as is
practical, this includes personnel as well as
material. Under no circumstances should
CHILDREN be allowed in work areas.
Primary Precautions
These machines are supplied with a moulded 13
Amp. Plug and 3 core power cable. Before using the
machine inspect the cable and the plug to make
sure that neither are damaged. If any damage is
visible, have the tool inspected/repaired by a suitably
qualified person. If it is necessary to replace the plug,
it is preferable to use an ‘unbreakable’ type that will
resist damage. Only use a 13 Amp plug, and make
sure the cable clamp is tightened securely. Fuse as
required. If extension leads are to be used, carry out
the same safety checks on them, and ensure that they
are correctly rated to safely supply the current that is
required for your machine.
Work Place/Environment
Make sure when the machine is placed that it sits
firmly on the bench or stand, that it does not rock,
that it is sufficiently clear of adjacent obstacles so
that you have unimpeded access to all parts of the
machine. The machine is designed for indoor use, do
not use when or where it is liable to get wet. Keep
the machine clean; it will enable you to more easily
see any damage that may have occurred. Clean the
overall machine with a damp soapy cloth if needs
be, do not use any solvents or cleaners, as these may
cause damage to any plastic parts or to the electrical
components. Clean the machine components with
a lightly oiled cloth. If the machine is liable to be
standing idle for any length of time a light coat of
machine or spray oil will minimise rusting.
It is good practice to leave the machine unplugged
until work is about to commence, also make sure
to unplug the machine when it is not in use, or
unattended. Always disconnect by pulling on the
plug body and not the cable. Once you are ready to
commence work, remove all tools used in the
setting operations and place safely out of the way.
Re-connect the machine.
Carry out a final “tightness” check e.g. chuck or face
plate, workpiece, tool rest, etc., check that the
correct speed has been selected.
Make sure you are comfortable before you start
work, balanced, not reaching etc. If the work you are
carrying out is liable to generate flying grit, dust or
chips, wear the appropriate safety clothing, goggles,
gloves, masks etc. If the work operation appears
to be excessively noisy, wear ear-defenders. If you
wear your hair in a long style, wearing a cap, safety
helmet, hairnet, even a sweatband, will minimise
the possibility of your hair being caught up in the
rotating parts of the tool, likewise, consideration
should be given to the removal of rings and
wristwatches, if these are liable to be a ‘snag’ hazard.
Consideration should also be given to non-slip
footwear, etc.
DO NOT work with cutting tools of any description if
you are tired, your attention is wandering or you
are being subjected to distraction. A deep cut, a
lost fingertip or worse; is not worth it! Above all,
OBSERVE…. make sure you know what is happening
around you, and USE YOUR COMMON SENSE.
5
Code 502703
Model AT1628VS
Rating Trade
Power 230V 50Hz 1.5kW
Speed Low 0-1,600rpm High 300-3,750rpm
Spindle Taper MT2
Spindle Thread M33x3.5mm (Ref T38)
Taper Tailstock MT2
Distance Between Centres 700mm
Max Diameter Over Bed 203mm
Overall L x W x H 1115 x 450 x 460mm
Weight 96kg
Specification
Specific Safety Instructions for Woodturning Lathes
1. Do not use ‘split’ work pieces.
2. Always start at the lowest speed when starting a
new task.
3. Check that the tool rest is at or slightly below the
centre line of the workpiece.
4. Check the workpiece is securely mounted in the
lathe before switching on the power.
5. Rotate the workpiece by hand, to check that it
is centralised, clear of the tool rest, not ‘split’ or has
loose knots.
6. Where lathes have the facility to be reversed; check
the machine is rotating in the correct direction.
7. If your lathe has the facility to run in reverse, you
must ensure that the mounting accessories (chucks,
faceplates etc.,) can be ‘locked’ onto the lathe
mandrel, and in the case of chucks have some form
of security device to prevent them ‘unwinding’ during
reverse operation.
8. Make sure your tools are stored/racked away from
the turning area of the lathe. Do not reach over a
rotating workpiece at any time.
9. Do not ‘dig in’ or try to take too large a cut.
10. Do not leave the lathe running unattended; or
leave the machine until everything is stopped.
11. Some turning tools may have specific sharpening
angles that have been determined by the
manufacturers; when re-sharpening, adhere to these
angles to maximise the finish of your work.
Assembly Instructions
6
Please take some time to read the section entitled
“Illustration and Description” to identify the
various parts of your machine so that you are familiar
with the terminology we will use to enable you
to set up and operate your table lathe safely and
correctly.
The lathe and its accessories will arrive coated with
corrosion preventative grease. This will need to
be cleaned from the lathe, its components and
accessories prior to it being set up.
Use degreaser to remove the barrier grease. Be
warned, it will stain if you splash it on clothing etc.,
wear overalls, rubber gloves are also a good idea,
as is eye protection. After cleaning, lightly coat the
machine with a thin layer of light wax. If you used
paraffin/kerosene make sure you apply this thin film
sooner rather than later.
WARNING: The wood lathe is a heavy machine, it is advisable to
use a lifting device such as a hoist, scissor lift or seek help when
assembling the lathe.
The majority of the machine comes fully assembled, the remaining items to be assembled is described below.
Lathe Assembly (Code: 502703)
Unpack your new 1628 Variable Speed Lathe and recycle the packaging responsibly.
The cardboard packaging is biodegradable.
Locate the motor plate handle (E) and screw it into
the pre-drilled hole in the motor tension bracket, see
figure 1
Figure 01
We recommend you remove the
headstock, tool rest and tailstock from the
lathe bed before lifting the lathe assembly
off the pallet as the lathe is very heavy.
1. Loosen the headstock stop bracket (a), to the
left side of the lathe bed and with help slide the
headstock off the lathe bed and place safely aside,
see figures 2-3.
2. Remove the tailstock stop bolt (b) from the right
hand side of the lathe bed and remove both the
tailstock and tool rest assembly and place safely
aside. (See figures 4-5-6)
Figure 02
Figure 03
Remove the headstock from the lathe bed
E
Headstock stop bracket
a
Assembly Instructions
7
Lathe Stand Assembly (Code: 502705)
Figure 04
b
Figure 05
Figure 06
3. Lift the lathe bed from the pallet onto a work
bench, see figs 7 then refit the headstock, tool rest
and tailstock as described in steps 1 and 2, see
figure 8
Figure 07
Figure 08
1). Locate the two lathe stands (F) and the four feet
(G).Screw the threaded feet into the pre-drilled holes
to the base of the stands. (See figure 9)
Figure 09
F
G
Continues Over...
A
Assembly Instructions
8
2. After removing the above lift the lathe bed using a
scissor lift, lifting host or seeking help.
3. Place the stands (F) to each end of the lathe bed
and line up the holes in the stands with threaded
holes in the lathe bed, secure using the 3/8" bolts and
washer (c),see figures 10-11-12-13.
4. Replace the headstock, tool rest and tailstock. (See
figure 14)
Remove the headstock, tool rest assembly
and tailstock from the lathe bed as before
to make it easier to assemble the stands
Figure 10
Figure 11
Figure 12
Figure 13
Use a lifting device as a scissor lift for example to
raise the lathe bed to mount the lathe stands
Figure 14
c
c
Lathe Extension Assembly (Code: 502704)
Assembly 1
The lathe extension (H) bolts onto either end of the
lathe bed which increases the length of the lathe for
turning larger projects. The lathe extension can also
be mounted to the stands for turning large diameter
projects.
1. Locate the lathe extension (H) and 3/8" Hex bolts
and washers (d). Remove the tailstock stop pin from
the end of the lathe, see figure 15 and place safely
aside.
2. Line up the centre hole in the lathe extension (H)
with the lathe bed centre pin, see figure 16, push on
the lathe extension so it’s flush against the lathe bed,
line up the holes and secure using the 3/8” Hex bolts
and washers (d). (See figure 17)
G
Adjust the feet (G) until the lathe is level
F
Assembly Instructions
9
Assembly 2
Figure 17
Holding the lathe extension, secure in place using the
3/8” Hex bolts and washers (d)
Figure 15
Remove the tailstock stop “PIN” and place safely aside
Figure 16
Slot the centre pin into the centre hole in the lathe
extension (H)
d
H
1. Line up the holes in the lathe extension (H) with
the threaded holes in lathe stand (F) and secure
using the 3/8” Hex bolts and washers (d), see figure
18.
Figure 18
Using the 3/8” Hex bolts and washers (d),
secure the lathe extension in position
H
2. Release the headstock lock and slide the headstock
down to the end of the lathe bed and lock in position.
Slide the tool rest assembly onto the lathe extension
(H), undo the tool rest locking handle and remove
tool rest. Locate the tool rest extension (I), slot the
tool rest extension into the machined recess and
tighten the clamping handle.
3. Loosen the clamping handles on the tool rest
extension (I) and slot the tool rest into the extension,
tighten the tool rest locking handle. (See figure 19)
Figure 19
d
I
H
Tool rest
Tool rest lock
Tool rest assembly
Illustration and Description
10
Tailstock
Access panel
Tailstock wheel
Motor plate handle
Tailstock barrel lock
Tailstock lockTailstock lock stop
Headstock
Motor locking handle
Faceplate
Spindle speed LED
Live centre
Lathe bed
Tool rest lock
Control box
Headstock pivot lock
Headstock locking handle
Tool rest
Banjo lock
Banjo
Illustration and Description
11
The control box has a magnetic base enabling it to be
positioned anywhere on the lathe
ON (Green) and OFF (Red) buttons
ON
OFF
Forward and Reverse switch The Speed Control Knob, enables you to increase
or decrease the speed of the spindle
Headstock Pivot Lock, pull this knob to rotate the
headstock to the desired position
Indexing ring facility and locking pin is used for fluted
columns, clock faces and accurate hole positioning
Index lock
pin
Indexing ring
Operating Instructions
12
Rotating the Headstock
The Headstock can be swivelled in any position
by lifting up the Headstock locking handle (a) and
pulling the Headstock pivot lock (b) out, swivel the
Headstock to the desired position is reached, lock in
place by pushing down the headstock locking
handle (a). (See figure 18)
The Headstock incorporates two index positions
45˚and 90˚, swivel the headstock until it locks in
place to allow bowls to be turned in front of the
lathe. (See figures 19-20)
Figure 18
Lift up the Headstock locking handle (a), pull the
Headstock pivot lock (b) out and swivel the
Headstock to the desired position
Figure 19
The Headstock locked in the 45˚ index position
Figure 20
The Headstock locked in the 90˚ index position
Removing the faceplate
Locate the spindle lock pin (D) and the spanner (B),
inset the locking pin (D) into the pre-drilled hole
in the headstock and using a Hex key loosen the
grub screw on the spindle, see figure 21. Using the
spanner (B) remove the faceplate, see figure 22.
Figure 21
Figure 22
a
b
D
B
Hex key
Faceplate
Operating Instructions
13
Indexing facility
Removing the Drive Centre
The Indexing ring is situated to the left side of the
headstock which incorporates 36 positions at (10˚)
segments. To the side of index ring is the index
locking pin to lock the spindle in position. The
indexing facility is useful for fluted columns, clock
faces and accurate hole positioning. (See figure 23)
Figure 23
Index ring
Index lock pin
10˚ Segments
Index marker
Figure 24
Line up the measurement you require on the index
ring with the index marker on the headstock and
screw in the index locking pin to lock the spindle in
position. (See figure 24)
NOTE: Make sure the measurement is in line with
the index marker otherwise the locking pin may
not in gauge properly.
To remove the drive centre from the spindle, locate
the push rod (C), insert it through the index ring
assembly and push the drive centre out, see figure 25.
Figure 25
Drive centre
C
Changing the belt speed
Note: The lowest speed pulley combination
is furthest from the faceplate, the smallest
motor pulley diameter to largest spindle
pulley diameter.
DISCONNECT THE LATHE FROM
THE MAINS SUPPLY BEFORE
CHANGING THE BELT
DISCONNECT THE LATHE FROM
THE MAINS SUPPLY
Open up the pulley access panel on top of the
headstock by removing the Hex screw. Slacken the
belt by loosening the motor locking handle (a),
move the motor until the belt is slack enough to be
reposition. (See figure 26)
Figure 26
Loosen the motor locking handle (a) enough
to allow the pulley to be repositioned
a
Continues Over...
Repeat the procedure for the live centre in the
tailstock.
Operating Instructions
14
Reposition the belt, making sure the groves in the
belt slot into the groves in the pulleys. Pull/push
the motor assembly until the belt is under tension,
retighten the motor locking handle (a). (See figure
27)
Close the pulley access panel and replace the Hex
screw.
Figure 27
Maintenance
The woodturning lathe has little maintenance, but
it is advised to do the following checks to keep the
lathe in good working order.
After every use
• Clean wood shavings away from the lathe bed and
tool rest
• Smear a light coat of wax (Protec Tool Wax Polish,
Code. 211835) over the lathe bed to allow the Banjo
and Tailstock to run smoothly over the lathe bed and
to prevent corrosion.
Monthly check
• Check the tension of the belt and adjust, see
previous page for changing the belt speed.
• Check any build up of wood shaving on the motor
and spindle pulley’s and clean if necessarily.
• Using a airline, blow out the motor’s air vents.
NOTE: Always use a dust mask and eye protection
NOTE: If the lathe not going to be used for a period of time, smear a light coat of
wax over the lathe bed and place a dust sheet over the lathe.
Wax Points
Parts Breakdown/List
15
Headstock Assembly A
Parts Breakdown/List
16
Headstock Assembly A
Parts Breakdown/List
17
Headstock Assembly A
Parts Breakdown/List
18
Body Assembly B
Parts Breakdown/List
19
Body Assembly B
Parts Breakdown/List
20
Stand Assembly C (Optional)
Parts Breakdown/List
21
Wiring Diagram
22
Notes
23
Please dispose of packaging for the product in a responsible manner. It is suitable for recycling.
Help to protect the environment, take the packaging to the local recycling centre and place into
the appropriate recycling bin.
Do not dispose of electric tools together with household waste material. In observance of
European Directive 2002/96/EC on waste electrical and electronic equipment and its
implementation in accordance with national law, electric tools that have reached the end of their
life must be collected separately and returned to an environmentally compatible recycling facility.
Only for EU countries
Loading...