AXIS SPIN AX-2200 User Manual
Spin
Model: AX-2200
AXIS SHAVERS INSTRUCTION MANUAL
PLEASE READ DIRECTIONS COMPLETELY BEFORE USE.
AXIS/Bodyline Products International, Inc.
198 N. Brandon Drive
Glendale Heights, Illinois 60139 USA
Congratulations!
You are now the proud owner
of an Axis battery-powered
Shaver AX-2200.
Before using your shaver, please
read the instructions in this
manual carefully for its proper use
and care. Please keep the manual
handy for ready reference.
Made in China
play hard, be smooth.
Axis Spin |4| English
Axis Spin |5| English
IMPORTANT
SAFETY INSTRUCTIONS
When using an electrical appliance, basic precautions should always be followed, including the
following:
Read all instructions before using your shaver.
WARNING
> Always provide close adult supervision when using
your shaver near children or the disabled.
> Follow all instructions in this manual carefully. Do
not use attachments with your shaver that have
not been specifically recommended by us.
> Do not use a unit that is not operating normally,
has been immersed in water or other liquid.
> Never operate your shaver outdoors. Avoid use in
the vicinity of aerosol products or where oxygen
is being administered. Also, keep the cord away
from heated surfaces.
> Do not insert foreign objects into any of the open-
ings in the unit.
Axis Spin |6| English
Axis Spin |7| English
> Avoid exposing the unit to direct sunlight or ambi-
head guard
floating
heads assembly
on/off switch
battery
compartment
ent temperatures above 140°F (60°C).
PARTS OF YOUR SHAVER
> To avoid injury to the face, do not use the unit if the
cutters or head assembly have been damaged.
> For home use only.
SAVE THESE INSTRUCTIONS
Axis Spin |8| English
Axis Spin |9| English
Your shaver is designed and manufactured to exacting standards in order to provide you with years of
close, comfortable shaves.
Feeling for your shaver
It normally takes about three weeks for your skin
to adjust to a new electric shaver. As you use your
shaver, you will develop a shaving style that is most
comfortable and effective for you. This “breaking
in” period may be somewhat longer for those with
sensitive skin or those who vary their shaving techniques. To repeat, for a closer and more comfortable
shave, you must allow yourself those 3 weeks for
your beard and skin to adjust to the electric shaver.
Upon unpacking your shaver, you may notice a
white/gray powder on the inner cutters and surface
of the heads. This is a factory-applied lubricant that
will help ease the breaking in period and disappear
with normal use.
Axis Spin |10| English
Axis Spin |11| English
SHAVING TIPS
1. Keep the unit clean and dry at all times.
2. Wash and dry your face thoroughly prior to
shaving and wait at least 15 minutes after getting up
before shaving.
3. Turn your shaver on and then let the 2 floating
heads follow the contours of your face to give you a
smooth, close, comfortable shave.
4. Stretch your skin with your free hand while using
straight or circular strokes. This will make the hairs
stand out from your face and allow the inner cutters
to reach them more easily. Shave against the grain
for optimum results.
5. To ease the cutting and avoid floating head wear,
do not apply the shaver to your skin with high pressure. Apply soft, gentle strokes while shaving.
6. The normal replacement period for the 2 floating
heads and 2 inner cutters is about one year; In order
to maintain maximum shaving performance and
comfort, replace the heads and cutters once a year.
To order replacement parts, please refer to the
“Ordering Replacement Parts” section of this manual.
Axis Spin |12| English
Axis Spin |13| English
To Insert the Batteries
fig.1
fig.2
fig.2
fig.3
1. Slide the On/Off Switch down to the “Off” position.
2. Remove the battery compartment cover by pulling it straight down from the shaver body.
3. Insert 2 “AA” alkaline batteries. Be sure to orient the
batteries properly to the (+)
and (-) indicators.
CAUTiOn: When your
device requires new batteries,
please insert only 2 new AA
alkaline batteries. You must not combine one old or
used battery with one new battery as serious leakage will occur and thus damage the unit.
USING YOUR SHAVER
To maximize shaving comfort and closeness,
periodically remove the head assembly to determine
if your shaver needs
cleaning, particularly if
you have a heavy beard
and use the shaver daily.
If you routinely check the
Axis Spin |14| English
Axis Spin |15| English
amount of shaven hairs under the head and clean
the entire head assembly when necessary, your
shaver will always run at peak performance.
1. Remove the protective plastic head guard.
2. Ensure that the floating heads and inner cutter
assembly are not damaged. Replace damaged parts
before using. To obtain replacement parts, refer to
the “Ordering Replacement Parts” section of this
manual.
3. To turn shaver on, slikd the On/Off switch up to
the “on” position.
4. Gently stretch the skin of your face with your free
hand while moving the shaver slowly and smoothly
against the grain of your beard. Hold the shaver at
a 90° angle to your face while maintaining contact
with the floating heads.
5. To shave the chin area, gently pull the skin upward and slide the shaver in an easy upward motion.
To avoid damaging the floating heads, press lightly,
not too hard.
6. Turn shaver off and replace protective head
guard.
Axis Spin |16| English
Axis Spin |17| English
CLEANING YOUR SHAVER
fig.4
Before cleaning, switch off the product by sliding the
switch downwards.
Wet cleaning
1. Slide the switch to off position
2. Remove the floating heads assembly by
holding the body in one hand and
pulling out the cutter assembly by
the other.
3. Switch on the product and wash
the blades in cold or warm water.
4. After washing, switch off the product, wipe dry
with a soft cloth and leave it in an airy place until fully
dried.
5. Attach the floating heads assembly properly to the
body to ensure smooth operation.
Using the cleaning brush
1. Slide the switch to off position.
Remove the floating heads assembly by holding
the body in one hand and pulling out the cutter
Axis Spin |18| English
Axis Spin |19| English
assembly by the other.
fig.5
fig.6
fig.7
3. Remove inner cutter assembly by
pushing down and turning counter
clockwise the srew knob in the center,
then pull upwards away from the outer
cutter assembly.
4. Clean hairs off with brush supplied.
To maximize shaving comfort and
closeness, periodically remove the
head assembly to determine if your
shaver needs cleaning, particularly if
you have a heavy beard and use the shaver dairy.
If you routinely check the amount of shaver hairs
under the head and clean the entire head assembly
when necessary, your shaver will always run at peak
performance. After cleaning, replace the inner cutter
assembly back into place.
imPORTAnT! Make sure that the center knob
is locked into place by pushing down and turning
clockwise.
5. After cleaning, always replace the plastic head
guard to protect the floating heads.
Axis Spin |20| English
Axis Spin |21| English
nOTE: To avoid damage, be sure to thoroughly
wipe pre-shave lotion or shaver oil from the shaver’s
body.
REPLACING THE BATTERIES
If you use your shaver daily, the alkaline batteries will
provide approximately 3 hours of shaving operation
time. If the operating power seems low, replace the
batteries. Please refer to the “To Insert the Batteries”
section of this manual.
STORING THE SHAVER
If the shaver is to remain unused for a long period
of time, remove the batteries and store the unit in a
cool, dry place.
imPORTAnT! For optimum shaving performance and results, we recommends that you
replace your shaver’s floating heads and inner
cutters once a year.
Axis Spin |22| English
Axis Spin |23| English
To remove floating heads and
1 2
5
screw
knob
pin
3
4
locating
hole
inner cutter assembly
To replace floating heads and inner
cutters, please refer to the “Ordering
Replacement Parts” section).
Skin irritation or a deterioration
of shaving performance typically
indicates that your cutting heads
need to be replaced. Replacement
intervals will vary with individual use
and different beard types.
1. Grasp the floating head assembly and gently lift it
off from the shaver. (figure 8)
2. Detach the inner cutter assembly (figure 9)
by pushing down and turning counter clockwise
the screw knob in the center (figure 9), then pull
upwards away from the outer cutter assembly.
3. Then, remove outer cutter assembly. (figure 10)
To replace floating heads and
inner cutter assembly
1. First, insert the new outer cutter assembly into
Axis Spin |24| English
Axis Spin |25| English
the frame, then insert the new inner cutter assembly
back into the housing and lock in place by pushing
down and turning clockwise the screw knob located
in the center. Please make sure that the locating
hole (figure 10) is lined up with the pin as seen in
figure 9.
2. Please make sure that the floating head and inner
cutter assembly is secure before attaching floating
head and inner cutter assembly to shaver.
3. Always keep protective head guard attached
when shaver is not in use. This will assure that the
floating heads will not be damaged.
Ordering replacement parts
Please contact Axis/BPI at 1-877-263-9500
to order replacement parts for your Axis shaver.
Please refer to the following part number.frame,
outer foil frame and inner blade.
Part Number: AS-1
Description: Replacement Rotary Heads and
Rotary Blades Assembly for AX-2200
> The above parts are available at the retailer from
whom your shaver was purchased.
Axis Spin |26| English
Axis Spin |27| English
If your shaver requires service
Call Axis at 1-877-263-9500. To assist us in
serving you, please have the model number and
date of purchase for your shaver available.
AXIS / Bodyline Products International, Inc.
1-YEAR LIMITED WARRANTY
AXIS / Bodyline Products International, Inc. (BPI)
warrants that your product, except as noted below, is
on the date of purchase free from defect in material
and workmanship for a period of one year. In the
event of a defect in material or workmanship, AXIS /
BPI will repair or replace this product with new parts,
free of charge as follows:
1. The warranty is extended only to the original
purchaser. A purchase receipt or other proof of date
of the original purchase is required for service and
parts replacement under this warranty.
2. Do not return the product to the retailer from
whom this product was purchased.
3. Contact AXIS / BPI toll-free at 1-877-263-9500
to obtain authorization during the warranty period to
return the defective product by mail, postage prepaid.
Axis Spin |28| English
Axis Spin |29| English
LIMITATIONS AND EXCLUSIONS
There are no express warranties except as listed
above.
This warranty only covers failures due to defects
in materials or workmanship that occur during
normal use. It does not cover foils, blades, cutters,
or attachments or damage that occurs in shipment,
or failures that are caused by products not supplied
by AXIS / Bodyline Products International, Inc., or
failures that result from accident, misuse, abuse, and
neglect from mishandling, misapplication, improper
maintenance, improper cleaning, alteration, modifica-
tion, line power surge, or commercial use of the
product, such as hotel, office or rental use of the
product, or service by anyone other than AXIS /
Bodyline Products International, Inc., or damage that
is attributable to acts of God.
AXIS / BODYLINE PRODUCTS INTERNATIONAL,
INC. SHALL NOT BE LIABLE FOR INCIDENTAL OR
CONSEQUENTAL DAMAGES RESULTING FROM
THE USE OF THIS PRODUCT OR ARISING OUT OF
ANY BREACH OF THIS WARRANTY.
ALL EXPRESS AND IMPLIED WARRANTIES,
INCLUDING THE WARRANTIES OF MERCHANDISE
Loading...