Axis DV426, DV426-4G Instruction Manual

Download

INSTRUCTION MANUAL

DV426/DV426-4G

4 Channel DVR Black Box Recorder

with WiFi, GPS & SATA SSD 2YEAR WARRANTY

SPECIFICATIONS

- Record Type Quad

- 4G: DV426-4G Only

- GPS: Yes

- WiFi: Yes

- Vehicle Tracking: Yes

- Max Resolution: 1920 x 1080 (100FPS)

- Real Time Recording: Yes - Auto or Scheduled

- G-Sensor: Yes

- Motion Detection: Yes

- AV Output: VGA, CVBS (RCA Adaptor Included)

- Monitor View: Normal/Mirror Image Selectable

- Video Compression: H.264 for High Quality Video

- Reverse Camera Compatible: Yes

- Camera Connection: 4 x 4-Pin

- Lockable Storage: Yes - 1 x 2.5” SATA SSD (Not Inc), 1 x 128GB SD Card (Not Inc)

- Operating Voltage: 9 to 36V

- Alarm Inputs: 6 CH

- Alarm Outputs: 2 CH

- Ignition Signal: Yes

- Speed Signal: Yes

- Timer Recording: Yes

- Adjustable Frame Rate & Bit Rate: Yes

- User Password Protection: Yes

- Operating Temperature: -20°C to 70°C

- Power Consumption: 15W (Working)

- Dimensions: 183 x 38 x 148mm

- Includes: Keys, Antenna Kit, Remote Control, Power Cable, Alarm Cable, USB Cable

1. Specifications

Operating system

Linux

Operating interface

Graphical menu operation interface(OSD)

Video permission

Administrator & user setting

Video input

4 x 1080P analog high definition

CVBS output

1CH 6pin aviation

VGA output

1CH VGA output, 1080P

HDMI output

NULL

Video display

1 、2、3、 4

Video standard

Compression

H.264 main profile

Audio input

4 channels

Audio output

1 channel

Record format

Synchronized video & audio recor din g

Audio compression

ADPCM

Image resolution

Max 4 x 1080P(1920*1080)

Video bit rate

64kbps~4Mbps/channel

Storage

56~2700MB/(channel*hour)

Audio bit rate

32kbps

Storage

2.5 inch SATA SSD x 1, max 2TB; SD card x Alarm input

6 channels

Alarm output

2 channels, 1 buzzer

Motion detection

High/low/off sensitivity adjustable

1 channel

RS232

1 channel for RFID

RS485

1 channel for Panic Button

CAN

2 channels

RJ45

1 channel

USB mini-B

1 channel

USB2.0

2 channels

4CH HD DVR

System

Video

Audio

Digital

processing &

storage

PAL: 25FPS, NTSC: 30FPS

1, max 128GB

connector output PAL/NSTC

Alarm

Interface for

communication

1channel for copying file(SSD、SD) and firmware upgrade 1 channel for copying SSD file(on ly for c onnecting to computer USB)

USB3.0 NULL

WIFI hotspot/AP

optional

/Gyroscope

Windows client

Web portal

Available

Input

Clock

Built-in clock, Calendar

Wireless

GPS

G-Sensor

Software

Power

Electrical spec

2G/3G/4G optional WIFI optional

Internal or external GPS/GLO N AS S module, coordinate/speed can be encoded in video stream and upload ed to ser ver by wireless communication

Available six axis sensor

Available

iOS client Available

10~32V Current Draw 12V@3.5A Max Power

Consumption Standby Power

Consumption Operating temp. &

humidity

Super Capacitor Available

60W

100mW

-20～70 degree/ <100%

SENSOR-I

Reversal

Brake

2. Precautions

1、Motion detection functi on is set to OFF by default. Al arm fil es wi ll be create d when there’s motion detected when set ON.G-sensor recording is recommended to set ON during dri vi ng for em erg ency recor ding use. G-sensor level is optional.

2、If the DVR can not boot up, try to remove all storage disks from the DVR, and then restart the DVR to check whether it can boot normally or not.

3、Make sure the yellow ACC wire is connected to the ignition wire and the red V+ wire to the positive pole of the battery. In this case, the DVR can continue to record for sometime after the vehicle engine is off. If the ACC wire (the yellow one) and the V+ wire (the red one) are connected directly to the positive pole of the battery, the DVR will still work even if the vehicle is not started. If the ACC wire and the V+ wire (the r ed on e) ar e c on nected directly to the ignition wire of the vehicle, the recording files will be easily damaged when the vehicle engine is off.

4、All the disks must be formatted on the DVR before use.

5、The login user name can not be changed. Password is editable.

6、All types of video files including event recording files will be overwritten by default. If not to overwrite the event files, set [Event Rec. Lock] to OFF. in the menu of [Event Rec.] under [Record].

7、

The corresponding types of SENSOR-IN1~6 on the trigger line are as

follows:

ALARM INPUT 1~4

input

3. Main Features

Appearance

 Smaller than the previous models.

Controlled by touch screen

 All settings and operations could be done through the monitor if connected with

the suggested touch screen.

Video and Audio

 4 channels * 1080p, 4 video inputs w it h audio  1 CVBS output(1 * 6 PIN OUT) with audi o  Support IPC camera

Recording

 4-CH Video & Audio Recorder (with i mag e r es olution up to 1920 X 1080), and

with G-sensor data and GPS data

 Multiple recording modes: pow er on r ecor ding, normal recording, schedule

recording, event recording (i.e., G-sensor recording, speed recording, motion detection recording, Alarm r ecor di ng 1~6, Panic button recording). Cyclic recording and 15 seconds pre-recording are supported.

 Recording files are stored in the SSD or SD card. Cyclic recording is optional.  Real-time recording of license plate numbers, dr iv ing speed,G-sensor/Gyroscope

6D accelerated speed, longitude and latitude, and GPS tracks.

Preview and Playback

 Support single channel, or 4 channels audio and video play simultaneously.  Support searching recording files by r ecor ding date, recording type.  Able to drag the progress bar when p lay ing back.  Indicate recording status, alar m stat us .

Storage Types

 Support SSD, SD cards (SDHC, SDX C)  If both SSD and SD card are used for stora ge, SSD will be preferred. SD card

can be stored only when SSD is not insta lled. 

 SD card can be removed convenient ly when not in recording or playing status.

Backup

 Support USB disk or USB hard disk to backup copy of recording files.

Network

 Support LAN, WI-FI, 2G/3G / 4G, automatic network switching;  LAN / Wi-Fi / Cellular connection (de fa ult priority: LAN > Wi-Fi > Cellular); auto

switch to LAN / Wi-Fi connection when available to save Cellular traffic.

 LAN, WI-FI and 2G/3G/4G have the priority of connections which wi ll switch

automatically to save 2G/3G / 4G dat a;

 Wi-Fi supports S TATION and AP mode, in which Wi-Fi AP mode supports

mobile direct connection devices, w hich is convenient for preview and configuration on mobile;

 Support remote real-time v ideo st r eam, image stream pre-view function  Support alarm recording, alar m information, log information, GPS trajector y

automatic upload function, which is convenient for vehicle abnormal conditio ns analysis and vehicle traject or y tracking;

 Support remote configurat ion, re mot e upgr ade w hich ac hiev e rea l re mote con t rol

function;

 Support PC Windows Client, mob ile IOS and Android APP. Users can remotely

monitor vehicles on computer or mo bi le phone

Alarm

 6 channels alarm inputs, one c hannel buzzer output and 2 channels alarm

outputs

 Over-speed alarm and accelerated-speed alar m  Motion detection alarm  G-sensor alarm  Panic button alarm

Charger

 5V, 1.5A output from the USB interface to mobile devices, such as mob ile phone.

Security

 User password protection. The D VR can only be accessed with correct

password.

 Support account management.

4. Wiring Diagram

BLANK

5. Connection - Front Panel

① LED Indicators ⑤ IR Receiver

② Electronic lock ③ Front Cover Buckle ⑦ SSD Slot ④ USB3.0 Interface ⑧ SIM Card Slot

⑥ SD Card Slot

5.1 LED

NULL

5.2 Electronic Lock

 Close the front cover and turn the groove by the key to the icon “off”, so as to

prevent hard disk drive fro m movin g out. Or t urn to the ic on “on” t o open t he fr ont cover.

 Electronic Lock Function: DVR will stop recording and buz zer will beep when the

front cover is open.

5.3 Remote Receiver

The IR Receiver is for the DV R to receive command from the remote control. Remote control instructions:

5.5 SSD card slot

 Hard disk Type: SSD (Max. capacity: 2T )  Size: 2.5 inches(70*100*7mm).

5.4 SD card slot

 SD card type: The maximum capacity of each card is 128G.  Insert、remove SD card

Step 1: Use the key to unlock and open front plate Step 2: Insert SD card to SD card slot

Wi-Fi Connector

Step 3: Close the front plate and use the key to lock

5.6 USB Slot

USB 2.0/3.0, Max. Capacity 2T

6. Back Plate

① Cellular Connector, TX/RX ② Cellular Diversity Connector, Rx ④ GPS Connector

③

6.1 Power

 power input

9 PIN Avation female connect to 9 PIN Avation male on the DVR

 Connection Connect ignition wire to yellow ACC wire of DVR, battery Positive to V+(Red wire), Negative to GND(black wire)

6.2 Camera(AVIN 1~4 )

 See below 4 cameras diagram.

 How to connect cameras

Connect 4 cameras on below cable which connects to back plate of DVR

Audio

Connect No.1 camera to AVIN1 4PIN Aviation male

Connect No.2 camera to AVIN2 4PIN Aviation male

Connect No.3 camera to AVIN3 4PIN Aviation male

Connect No.4 camera to AVIN4 4PIN Aviation male

6.3 LCD monitor

EDID (Extended Display Identi fi cat i on Data) is automatically acquired when power is turned on.Output resolution of the LCD monitor can be selected. Settings are as follows:

AUTO system format will be recognized as above

System Format

CVBS HD

AUTO NTSC/PAL 1080P/720P

 10” HD monitor introduction (Recommended)

Description

HD 10.1"Color monitor

HD 7"Color monitor

Audio output (loudspeaker)

VGA input

CVBS input

Max. Brightness

500 cd/m²

450 cd/m²

Minimum Operating

Mirror Function

159.5mm (H) ×

Consumption

less than 8W

less than 5W

 The parameter list of 7/10 inches HD monitor

Features used for HD DVR us ed for HD DVR

Resolution 1024 x 600 (RGB) 1024 x 600 (RGB)

Maximum Number of Cameras 1 1

Audio input 1 1

HDMI input / /

Trigger No No

Contrast

Temperature

Maximum Operating

Temperature

Viewing Angle Monitor U: 70/ D: 50, R/L: 70/70 U: 75/ D:75, R/L: 75/75

Monitor Diameter (mm)

Split Screen No No

6.4 Buzzer

If the DVR is not connected to the monitor, check the DVR's recording status through

the buzzer.

Buzzer will alarm if the DVR is not recording under Normal Mode which is set by default. To stop the buzzer from alar m ing, check whether the DVR is recording under the Normal Mode or not.

Buzzer warning functions are as f ol low s

Buzzer beep alarm will last for a while for all types of alarm event recording.

If the Buzzer beeps intermittent ly, it means that the DVR is unable to record.

Different beeping modes st and for different working status as below:

a. If the electronic lock is open: one long beep and one short beep

b. Diskless: one long beep and two short beeps

600：1 800：1

-20ºC, RH 90% -20ºC, RH 90%

+70ºC, RH 90% +70ºC, RH 90%

267mm (W) ×

30mm (T).

Volts 10-32V 10-32V

203mm (W) × 112mm (H)

× 28mm (T).

c. Disk file system exception : one long beep and three short beeps

d. If disks are normal but the alarm video files are full : two short beeps and one shor t beep

e. No camera input: two short beeps , and two short beeps after a second

f. If disks are normal but DVR is not in rec ording: two short beeps and three short beeps

6.5 Alarm Interface

 Alarm interface cable

See the picture below

10 PIN female head on the DVR connect t o 10 PIN male head

 Pin Definition:

10 PIN 1 2 3 4 5 6 7 8 9 10

Colour

red

pink

blue

gray

white

purple

green

yellow

black

Definition

Alarm

Alarm_in

out2

1. There are 6 alarm inputs including alarm inputs 1 ~ 4, reversal input, brake input,

out1

which can trigger the alarm recording. . Cursor will be displayed when the alarm input channel is working. The first 4 on es can be self-defined by user.

GND GND

2. Alarm output 1 and Alarm output 2 are 12V output by default, which can be us ed as a trigger and need to be set up to co mbine w ith alarm input . You can also setup BUZZER for the output.

3. If Alarm input 1 is active and combined with Alarm output 1, the Alarm output 1

will output a high-level voltage to trigger other device.

6 Panic button (Optional)

 Overview The LEDs are used to show the device’s working status. But when the device is inst al led in the vehicle, it is not easy to check the LED on the front panel. Each of the LED indicate s t he corresponding status. Furthermore, the panic button on the panel makes it easier to tr igg er al arm for emergency by bookmarking a ma nual event.

 Pin Definition

8 PIN female head connect to 8 PIN male head（RS232&RS485） on the DVR

 LED

LED Color ON OFF

VLoss Amber

Rec

GPS Amber GPS cannot latch Normal Operation

Mem Red

Comm Amber

Power

Error Red Error with device Normal Operation

Event Red

 Button PANIC button, printed as “Bookmark”

Soft

green

Pale Blue

Any of the cameras have no

signal alarm

Recording Normal driving Not recording

Storage Alarm or no

Storage device

Device is not connected to

server

Device has power Device does not have power

Event-based Recording

(remains lit during Event)

Normal Operation

Normal operation or device is not connected to server if this

feature is disabled

Normal Operation

a. When pressed, a manual event w il l be tr iggered. b. When pressed, the Event LED wil l be temporarily illuminated. If the PANIC button alarm recording cannot be triggered, check if the alarm

recording button is open as shown be low :

If the alarm recording was triggered, there will be an alarm sign on the screen, as

shown below:

6.7 Built-in GPS antenna

Built-in GPS antenna soc ket and GPS antenna, as shown in the picture.

7. The Menu

7.1 Menu Introduction

Touch [MENU] on the remote or touch the bottom area, the LOGIN page will be displayed on the LCD screen. The Short cut Menu wil l be displayed a fter login. If y ou press [MENU] on the remote or Touch the bottom area again, the Main Menu will be displayed.

① System Time Display

② License plate number Disp lay

③ Recording Sign

The Recording Sign will turn red when rec ording

④ Playback Sign

The Playback Sign will turn red during playback.

⑤ Electronic Lock Sign

 Lock indicator turns red when electronic lock is locked and front c over is closed.  Electronic lock is different from menu lock.

⑥ GPS Sign The GPS Sign will be flashing when connecting. It will be always ON if successfully connected.

⑦ Cell Sign ⑧ Wi-Fi Sign ⑨ Video Loss Sign ⑩ Menu

Press [Area 10] to display MENU Si gn ⑪ Channel Name Sign

7.2 Menu Lock

 DVR supports two kinds of permissions: admin permissions and guest

Initial Passwo rd

123

321

permissions

 User permissions list

User Name admin guest

Password Modification

yes no

Enter the menu of

Enter all menus

Permissions

Playback，Display mode

switching and Volume

 User name cannot be changed, but user password is changeable. (See the

following instructions for chang in g pas sword)

 Username admin and password are needed to change the status of Menu lock.

The following picture shows how to change the Menu Lock status from ON to OFF.

 When the status of Menu Lock is On, username admin and password are

needed to enter menus like Record, Playback, Log, System and Disk. With username guest and password, only the Playback menu can be entered.

7.3 Keyboard Operation Instructions

：Switch letter case

：Exit the keyboard interface

：Delete the input letters

：Switch to the numeric interface

：Switch to the English alphabet inter face

：Switch to the special character interface

Character Switching Instructions

Letter Case Switching Instructions

7.4 Manually Record

Touch this icon to start or stop recording. Video files can be found in the Normal list of Player menu.

7.5 Playback

Video Playback button: Touch this icon to enter the calendar menu. Green marked date means it has recording files saved on that day.Select the date to enter the video file list, then select the file and touch Play icon to play video. You can select single or multiple videos at a time. Multiple videos can

be played in sequence and can be shifted to the next or the previous one

G-sensor recording

Event recording setup time

Event list

Speed recording

Event recording setup time

Event list

Panic button recording

Event recording setup time

Event list

Specific operation sees below.

: Search by month

: Search by year

Normal: Normal recording list, including Normal Recording, Power on Recording, Schedule Recording

Event: Alarm recording list , including alar m rec ordi ng 1~6, M otio n det ectio n rec ording, G-sensor recording, Speed r ecor ding, Panic button recording

Type Recording Time Co nt r ol Mode View Position

Normal recording Manual control Normal list Power on recording Manual control Normal list Schedule recording Pre-setup time Normal list

Alarm recording 1~6 Event recording setup time Event list

Motion detection recording Event recording setup time Event list

Capture: Screenshot list Play: Play the selected video file s Export: Export selected video files to USB

All: Select all video files in this page Exit: Exit

: Volume adjusting button

: Switch

: Play the previous/next video

: Pause/Resume playing

: Hide the play menu. And press [Area 1] to display.

: Exit playing

7.6 Log

System memo checking, memo output

7.7 Display mode switching

Mode switch button: Touch this ic on t o ent er t he M ode switch interface.

：One-division mode of Camer a

Left (CH1)

：One-division mode of Camera

Right (CH2)

：One-division mode of Camera

Front (CH3)

：One-div ision mode of Camera

Back (CH4)

Three-division mode of Camera

Left, Front and Back (CH1, CH3, CH4)

Three-division mode of Camera

Front, Back and Right (CH3, CH4, CH2)

Three-division mode of Camera

Front, Left and Right (CH3, CH1, CH2)

Three-division mode of Camera

Left, Right and Back (CH1, CH2, CH4)

：Two-division mode of Camera

Front and Back (CH3, CH4)

：Two-division mode of Camera

Left and Right (CH1, CH2)

：Four-division mo de of Camera

Left, Right, Front and Back (CH1, CH2, CH3, CH4)

：Four-division mode of Camera

Left, Front, Back and Right (CH1, CH3, CH4, CH2)

7.8 System

：Set the current selected mode as default.

：Exit.

System settings button: Touch System to enter the setup menu. A prompt dialog will display "Unable to record in set-up mode! Continue?” Touch OK to enter.

7.9 Disk

Disk management button: Touch the disk management icon, then y ou can view

the status of SSD, SD card and USB.

① Disk type

② ALL：The total capacity of disk，free：The remaining capacity of disk

If ALL shows 0.00MB, it means that DVR does not have access to this type of disk

③ Green area shows the capacity of all the recording files in the Normal list Red area shows the capacity of all the recording files in the Event list Blue area shows the capacity of all the pictures in the Capture list Yellow area shows the capacity of all the other files except those above

④ Touch to format the disk.  A di alog bo x displ aying “D isk dat a will be deleted! Continue?”will pop up. Press

OK to start formatting the disk

 The following picture is an example of formatting USB2

 If the disk cannot be formatted, please check if:

a. There is a disk in the slot

b. All recordings are set off

c. The FTP button is set off ⑤ It shows that the disk needs to be formatted before use. All new disks must be formatted before use.

⑥If SSD Out is ON, the recording files in the disks can be exported to computer via USB cable. Please note that only recor dings files can be exported in this way.

7.10 Volume

Volume : value 0~10, Default value is 5.

8. Record Setup

8.1 Power On Rec

is set to ON. Default is ON.

The DVR will start recording after power on when 'Power On Rec’

8.2 Cyclic Rec

setting the Cyclic Rec ON. Otherwise, it will stop recording when disk is full. Overwriting will cover all recording files including Event recording files by default.

New video files will overwrite the prev ious ones w he n disk is fu ll if

8.3 Event Rec

Event Rec.：Event recording type includes motion detection triggered alarm, G-sensor triggered alarm, alarm 1 ~ 6 triggered alarm ,Panic button trigger ed alarm and over speed

alarm. If the Event Rec is ON and corresponding alarm parameters are set, event recording will be activated when the events above are triggered. If the Event Rec is OFF, event recording will not be activat ed even if event is triggered.

Event Rec. Lock：

full, new video files will overwrite the previous ones(all recording files except Event Recording files) . When the Eve nt Re c. Lock is Of f, Cyclic Rec. is On and all disks are full, new video files

will overwrite the previous ones（all recording files include Event Recording files）.

If both the Event Rec. Lock and t he Cycl ic Rec. is O n an d all disks are

8.4 Video Quality

Resolution

the television

The main stream is used for video storage. The sub stream is used for video backup and network transmission.

① Resolution There are 5 levels of resolution in main stream menu for option,1080P, 720P, D1 (PAL), D1 (NTSC),AUTO. And 3 kinds of optional res olution in Sub st ream men u, CIF (PAL), CIF (NTSC),AUTO. The higher the resolution & the better the video quality is, the larger the video file will be. Therefore, the file size should be taken into account during configuration. In the Resolution options, AUTO is d ef in ed as follows:

Main stream Sub stream

DVR automatically gets

AUTO

mode of the camera, and records in

this mode at the corresponding

channel

② B it ra te There are 8 levels of bit rates in Main stream and Sub stream menu for selection, 4Mbps, 2Mbps, 1Mbps, 512Kbps, 256Kbps, 128Kbps, 64Kbps, AUTO. The higher the bit rate and the clearer the image is, the larger the video file will be. Therefore, all factors should be considered comprehensively.

In the Bit rate options, AUTO is def ine d as f ollows

DVR automatically gets t he PAL/NTSC

television mode of the camera, and

records in CIF(PAL)/CIF(NTSC) mode

the corresponding channel

the bit

Bit rate

Main stream Sub stream

If 1080P camera is connected,

AUTO

③ Fram e ra te There are 5 levels of frame rates in Main stream and Sub stream menu for option : 28fps, 25fps, 20fps, 15fps, 10fps, 5fps. The higher the frame rates and the smoother the picture is, the larger the video file will be.

rate will be 4Mbps . If 720P

camera, 2Mbps. And if D1 camera,

1Mbps.

SSD/SD capac ity Video Quality File length

8 * 1080P / 4Mpbs ≈150h

8 * 720P / 2Mpbs ≈300h

512G

8 * D1 / 1Mpbs ≈600h

1 * 1080P / 4Mpbs ≈1200h

1 * 720P / 2Mpbs ≈2400h

1 * D1 / 1Mpbs ≈4800h

8 * 1080P / 4Mpbs ≈38h

8 * 720P / 2Mpbs ≈75h

8 * D1 / 1Mpbs ≈150h

1 * 1080P / 4Mpbs ≈304h

1 * 720P / 2Mpbs ≈608h

1 * D1 / 1Mpbs ≈1216h

Whatever cameras are connected, the

bit rate will always be 64Kbps.

8.5 Record Channel

After set on recording (including all types) and selecting the recording channels, the corresponding channels will be recorded. If turning off a video channel, the corresponding channel will not be recorded even if the recording function is on.

Note: The config is for normal recording, but not for event recording. Event recording will record all channels by defau lt and it can’t be changed.

8.6 Event duration

When Event Rec is on, the file length of Event rec or din gs can be set to 5s, 10s, 15s.

8.7 File Length

The video file length can be set to 5mins, 10mins, 15mins.

8.8 Motion Sensitivity

Motion detection recording and sensitivity level setting: When there is an object moving and its movement amplitude exceeds the preset motion detection sensitivity level, Motion detection re cording will be triggered. For this kind of event recording, the pre-record time will be set as 15s and the post-event time is configured by Event Duration above.

Total video file length = pre-recording file length (default time 15s) + file length (configured by Event Duration).

If motion detection is off, event recording will not be triggered. Motion detection sensitivity can be set to two levels, low / high. Motion detection recording is on when low / high is selected. Motion det ection recording is off when OFF is selected.

8.9 G-sensor Sensitivity

G-sensor triggered recording and sensitivity level setting: When the acceleration or gyroscope of the G-sensor reaches the preset sensitivity value, G-sensor recording will be triggered. For this kind of event record or alarm record, the

pre-record time will be set as 15s and the post-event time is congured by Event

Duration above.

Total video le length = pre-recording le length (xed 15s) + le length

(congured by Event Duration).

If G-sensor triggered recording is o󰀨, event recording will not be triggered.

G-sensor sensitivity can be set to two levels, low / high. G-sensor triggered

recording is on when low / high is selected. G-sensor triggered recording is o󰀨

when OFF is selected.

①Acce.: to monitor rapid acceleration. The value will always be positive.

②Dece.: to monitor rapid deceleration.The value will always be positive.

③Turn_Acce: the acceleration of sharp turn. The value will be positive when turning

left, and negative when turning r ight. ④Turn_Gyr: the angular velocity of sharp turn. The value will be positive when turning left, and negative when turning right. ⑤Impact: the acceleration of impact event. The value will always be positive.

Filter: Acceleration sensor coef f ici ent on t he Z -axis. The value of Impact is calculated as below:

＋

abs(X)

(abs(X), abs(Y) and abs(Z) are the datas of the acceleration sensor on X-axis, Y-axis and Z-axis)

After the setting of threshold and duration is finished, the installation settings and the correction of the sensor will be need ed. By default, * If the vehicle accelerates continuously to the +X-axis while driving, and the value of Acce exceeds the threshold for 100ms, t he Acceleration Alarm will be triggered. * If the vehicle decelerates continuously to the +X-axis (or brakes) while driving, and the value of Dece exceeds threshold for 100ms, the Deceleration Alarm will be

abs(Y)＋abs(Z)*Fliter

triggered.

Forward

* If the vehicle turns quickly to the +Y-axis while driving, and the value of Turn_Acce exceeds threshold for 100ms, the T ur n_Acce Alarm will be triggered. * If the vehicle turns quickly to the -Y-axis while driving, and the value of Turn_Acce exceeds threshold for 100ms, the T ur n_Acce Alarm will be triggered. * If the vehicle turns quickly to the +Y-axis while driving, and the value of Turn_Gyr exceeds threshold for 100ms, the Turn_Gyr will be triggered.

The installation of the DVR: The coodinate system of DVR is shown as below:

Z-axis (vertical upward direction)

(the side with LED)

X-axis

The X-axis is the front of t he DVR(t he si de wit h LE D) . The Y -ax is is the le ft sid e of t he DVR(the side without lock). And t he Z-axis is the vertical upward direction.

The coodinate system of the vehic le is s hown as below:

(the side without lock )

Y-axis

Left

DVR has various installation postur es and inclinations. For example, if the X-axis of the DVR(the front side) is consistent with the driving direction of the vehicle, this is front inst al lat i on. If the X-axis of the DVR is opposite to the driving direction of the vehicle, this is reverse installation. And there are other situations, just like lateral fixati on. Therefore, the installation way is needed to be set before using. Besides, there is a situation that the DVR may be slightly tilted, so it is needed to correct the sensor at the same time.

Installation settings and Correction: Go to “Record - G-sensor sensitivity Setup - Correction Setup” page. See the picture below.

Forward: select the axis that cooincidents with the forward direction of the vehicle when driving. Left: select the axis that cooincidents with the left direction of the vehicle when driving.

For example, if Forward is set to be +X, and Left is set to be +Y, it means that the forward direction of the DVR is the direction of +X-axis while the vehicle is driving. If Forward is set to be -Z, and Left is set t o be + Y, it means that the forward direction of the DVR is the direction of -Z-axis and the direction of +Y-axis is on the left of the vehicle while the vehicle is driving , which means tha t the DVR is fixed v erticall y in the vehicle and the bottom of the DVR is fa ci ng the front of the vehicle.

After setting, press OK to exit. The vehicle will be still for more than 1 second, and then the correction is finished.

Warning: Before using, you must make sure that you have finished the installation settings and correction. During correction, the vehicle must be on a flat road, and keeping still. And the correction time must be no less than 1 second. If the DVR is uninstalled and re-installed, or its location changes evidently, the installation location must be reset.

8.10 File Type

File format setting.

9. Display

9.1 Camera display setting

Camera: Parameter setting for each corresponding camera channel: including brightness, contrast, saturat ion and hue.All values for default setting are 50. To change the value, drag t he bar to left or right to decrease or increase.

9.2 Camera name setting

Camera name: Set a camera name, then the camera name will be displayed at the bottom of the camera display.

Touch the camera name on the menu, then a keyboard menu will pop up to input a new camera name. Each camera name contains 8 characters in max. And camera name must NOT be blank.

9.3 System Language setting

Menu Language for option: English, Russian.

9.4 Audio Out

Audio out: Select the audio output channel in split mode.

9.5 OSD display setting

OSD configuration: Select w het her t o display time, channel name, license plate in video or not (if On, all the informati on above will be written in video and can be displayed in playback)

9.6 Menu on

Menu on: Set duration of menu display

Menu on: Menu on duration can be set to 30s, 60s , 120s an d Always. When it is set to 30s, 60s, 120s, it means that the menu will be hidden if there is no operation in 30s, 60s or 120s after it is open. When it is set to Always, the menu will always be there. Please be noted that if enter the menu, the recording will stop. In order not to affect the recording, it is not suggested to set the duration to Alw ays.

Menu lock: On means permission is required t o ent er t he menu; Off means permission is not require d t o ent er the menu; Username admin and password ar e r equired if to change the status of the menu lock.

9.7 Speed

Speed setting: The data source of overspeed comes from GPS. Speed units are optional:, Km/h or Mile/h. Overspeed is the threshold of overspeed, which can be set by user. Speed refers to the current speed of the vehicle. If the value of Speed exceeds the value of Overspeed, the over speed alarm recording will be triggered. The alarm switch is used for setting the overspeed alarm recording ON/OF F. I f it is ON, the overspeed alarm recording will be triggered when the vehicle is overspeed. If OFF, the overspee d al arm recording will not be triggered.

9.8 GPS

GPS: When the GPS antenna is properly installed, latitude, longitude and speed will be recorded into video files. The menu pr ovides G PS infor mati on of latitude / longitude, detectabl e sat ellites, accessible satellite etc.

Mode:GPS status. It will be shown as bel ow :

 Connected

 Disconnect  Locating

9.9 Mirror

ON: Turn on Mirror function OFF: Turn off Mirror functi on

10. Network

10.1 LAN port and server setting

 DHCP: Dynamic Host Configuration Protocol. To set it on stands for dynamic IPand

off, for static IP. Static IP must be manually input with IP addr ess, mas k and g atew ay. MAC address can be automatically assigned or revised.

 Enable LAN step 1: Connect the LAN cable to t he DV R. step 2: Go to “Network - Cellular” page.

step 3: If DHCP is set to ON, a dynamic IP will be automatically matched. If DHCP is set to Off, input the IP, mask, gateway and MAC manually. step 4: Touch OK to exit.

step 5: Go to “Network - Server” page and touch the LAN icon.

Step 6: Input LAN Server IP and Port. Touch OK to sav e the setting.

10.2 Wi-Fi network setup and server setup

Wi-Fi： Wi-Fi on/off DHCP: Dynamic Host Configuration Protocol. To set it on stands for dynamic IPand off, for static IP. Static IP must be manually input with IP address, mask and gateway. MAC address can be automatically assigned or revised.

SSID： Wi-Fi hot spot list Ap Internet: If it is ON, the hot spot of this D VR can be found on mobile phones.

 Enable Wi-Fi Step 1: Wi-Fi hot spot available

Step 2: Connect the Wi-Fi antenna at connector ⑥ of device rear panel Step 3: Go to Wi-Fi setup int er f ace, set Wi-Fi to ON and open the dynamic IP button.

Step 4: Touch SSID s ub-menu and the Wi-Fi hot spot shows up. Select the hot spot to connect and input password.

Step 5: Touch OK and quit t he Wi-Fi setup interface.

Step 6: Input Wi-Fi Server IP and Port in “Networ k-Server Setup” page.

Step 7: Wi-Fi network status shows “CONNECT SUCCESS” and server status

shows “Online”.

10.3 2G/3G/4G control and its network setup

Cellular: Cellular is on, meaning t hat 2G/3G/4G is on. Network Standard: WCDMA by default. APN &Access Number: Normally, the user doesn’t need to input user name and password for APN and Access number. The default setting is available. If it can’t communicate with the network under the default setting, please consult your local network carrier.

Username &Password: Reversed. OK: Save the settings and quit. Cancel: Cancel the settings and quit.

 Enable 2G/3G/4G step 1: DVR can search 2G/3G/4G signal locally.

Step 2: Connect the 2G/3G/4G antenna at connect or ⑤of DVR rear panel. step 3: Open the DVR front housing a nd in ser t the 2G/3G/4G SIM card.

step 4: Go to Cellular setup interface and set Cellular to ON.

step 5: Input the APN and Acce ss Numb er correc t ly. Access Nu mber ca n be s k ipped.

Step 6: Touch “OK” to exit.

step 7: Input 2G/3G/4G Server IP and Port in “Network-Server Setup” page.

step 8: Cellular network status shows “Success” and server status shows “Online”.

10.4 Network Status

Network Status: Users can check information such as LAN IP address、 MAC address、Wi-Fi network stat us、Wi-Fi IP address、Wi-Fi signal strength、 2G/3G/4G network status、2G/3G/4G signal strength, and Server status.

Additionally, users can verify w het her net work connection is successful or not.

LAN IP: Refers to the static IP set on Network-LAN page or the dynamic IP which is obtained automatically.

MAC: Refers to the static physical address set on Network-LAN page or dynamic physical address which is obtained automatically.

Wi-Fi: Wi-Fi on/off status obtained from Network-Wi-Fi page

Wi-Fi RSSI: Wi-Fi signal strength icon

Wi-Fi IP: Static IP obtained from Net w ork-LAN pages or dynamic IP.

Wi-Fi status: Wi-Fi status will be shown as below: CONNECT SUCCESS GETIP ERROR

Cellular : The on/o ff stat us of cellular acquired from Network-c ellular page Module: Display the Cellular module brand Wireless RSSI: 2G/3G/4G signal strength icon Wireless Type: Display the types of 2G/3G/4G module, the parameters and the corresponding types are show n as f ollows 2G: Receive 2G signal 3G: Receive 3G signal 4G: Receive 4G signal Wireless Status: Value and corres ponding meanings 1: Module initialization 2: Module exception 3: No SIMcard 4: Cpin locked 5: Signal abnormal 6: Networking failure SUCCESS: Networking success

... Server Status: Online / Offline

10.5 Server

The function of server setting is described as above (10.1,10.2,10.3).

10.6 FTP

Username/Port/Password: Correc t Username / Port / Password of th e FTP server must be

filled in. FTP: ON/OFF

Normal File: Two states, OFF and ON

 OFF: Upload alarm files only  ON: Upload all files (including Normal Files)

Cellular: Two states, OFF and ON

 OFF: Files are not allowed to be uploaded when Cellular is connected to the Internet  ON: Files are allowed t o be uplo ade d wh en Ce llul ar is c onnec te d to th e Internet. To save

network flow data, please select OFF.

Uploading: Display the progress bar of the uploaded file Filename: Display the file name of the file being uploaded Status: Display the working status of the FTP function

Successfully uploaded files can be found on the client as below:

11. System

11.1 Log in setup

Set user name and password for booting up. The initial password is 123.

11.2 License plate number setup

Input license plate number

11.3 System time setup

Format Setup:

Go to “System - Date&Time - Format_Setup” page. ①Time Zone: time zone sett ing.

②Date Format: set the format of date. ③24 Hour: if it is ON, time format will be displayed in 24-hour system. If OFF, in 12-hour

system.

Time Snyc Setup:

Go to “System - Date&Time - Time Sync_Setup” page. ①GPS: set GPS to ON/OFF

②NTP: set NTP to ON/OFF ③NTP Server: show the URL of the NTP Server

DST Setup:

Go to “System - Date&Time - DST_Setup” page. ①Enable: Set DCT setting to ON/OFF

②Offset: Adjust the offset after enabling DST ③Mode: Select the mode of DST(setup DST according to week or date) ④Start: Set start time of DST ⑤End: Set end time of DST

11.4 Scheduled Recording

Enable: Set scheduled recordin g O N/ O FF. Start: Set start time of scheduled recording. End: Set end time of scheduled recording. Week-day: Set scheduled recording by w eekday s. Select the w eekday s t o set pr eset. Scheduled Recording: * Support up to four appointed tasks. The recording duration is counted in minutes. * Recording time can overlap. * The start time of scheduled recording must be set ahead of the end time.

11.5 Exception

Buzzer: Set the buzzer to ON/OFF. Duration: Set the duration time of the buzzer.

11.6 ACC settings

Current vol.: Voltage of the work ing DVR

Shutdown vol.: Shutdown voltage function will work after DVR starts working for 1mins. DVR will shut down automaoi.iktically if current v oltage is lower than shut down voltage, and it will reboot only when the volt age is above the value.

ACC Duration: DVR will continue recording for a few seconds after ACC is disconnected. ACC delay time can be set to be 5s, 60s, 30min or 60min.

11.7 Alarm information setting

Alarm1~Alarm4: Customized alarm recording

Reverse: Reversing alarm recording. Parking line cursor will display when reverse alarm is triggered.

Brake: Brake alarm recording. Brake sign will display w hen brake alarm is triggered.

Left: Turning-left al arm recording. Turn-left cursor will display when turn left alarm is triggered.

Right: Turning-right alarm recording. Turn-right cursor will display when turn right alarm is triggered.

Priority: Set prioriti es for Alarm1~Alarm4, Reverse, Brake, Left, and Right.

When different types of alarm are triggered at the same time, alarms with the highest priority will work first.

Trigger Level: There are 3 options of Trigger Level. The options “Low” and ” High” are used for turning on alarm function. “Low” is generally used for debugging while “High” will be selected to turn on alarm function for on-road use. “Off” means turning off alarm trigger function.

Duration: Duration of alarm video recor ding

Alarm Out-Buzzer: Set the Buzzer ON, then it would beep for 5 seconds when

alarming.

Alarm Out-Output1: Set it ON, then 12V level output would come from the alarm wire of Output 1

Alarm Out-Output2: Set it ON, then 12V level output would come from the alarm wire of Output 2

Display: A full screen of one channel will display when this channel is triggered.

Curser: See the picture below.

①Camera name of the alarm-triggered channel.

②Press this button to turn on/off curser .

③Line selecting: There are five lines to be selected, Line U(up), Line D(down), Line

L(left), Line R(right) and ALL. The button is green if selected. You can use remote control to operate.

④There are four directions to adjust the shape of the cursor, Up,Down, Left and Right.

If Line U(the green one) or Line D(the red one) is selected, the selected line can be moved totally with these direction but t ons. If Line L or Line R is selected, the top po int of the select ed line can b e moved to le ft or right with Direction Up and Direction Down, and the bottom point of the selected line can be moved to left or right with Direct ion Left and Direction Right.

⑤Lines of curser. The selected on e w il l b e t hickened for three times. The two lines in the middle will not be processed. ⑥Touch OK to save the settings and exit. Cancel to exit without saving any settings.

Priority: See the picture below.

: Press it, then the priority value of the selected alarm will be added by 1. The bigger the value is, the lower t he pr iorit y will be.

: Press it, then the priority value of the selected alarm will be reduced by 1. The smaller the value is, the higher t he pr i or it y will be.

 Alarms with higher priority will be triggered first.  1 is the highest priority, and 8 is the lowest.

 If two alarms A and B are triggered at the same time, and A’s priority is higher

than B’s, then A will record first. After A finishes the recording, if B is still being triggered, B will then record. However, if B is no longer being triggered now, it will not record.

 If alarm B is triggered and at the process of recording, however, alarm A, whose

priority is higher than B, is triggered then, B will not stop recording.

11.8 Update

 For single device

Step 1: Copy the folder to USB disk or SD card root directory and insert the USB disk or SD card into DVR.

Step 2: Power off the DVR and reboot it, then it will upgrade automatically. Or in the menu Menu -> System -> Update, touch OK to confirm to upgrade. Both methods can start the upgrade process.

Step 3: When “Update success!” is shown on the DVR monitor, the DVR will reboot automatically.

Step 4: After rebooting, please check if the version is the same as the one you copy into “upgrade” folder. Please go to M enu -> System -> Info to check it.

 For batch upgrade As the upgrade package will be deleted after the upgrade process is done on device, so if you need to upgrade more t han one device, please carry out as follows:

Step 1: Rename the package “dvxxx_upgrade_201xxxxxxxxx” to “dvxxx_upgrade_never_rename”( " xxx" in the "dvxxx_upgrade_never_rena me" is the corresponding product model number)

Step 2: Copy the package to the root directory of USB disk or SD card , and insert it to DVR.

Step 3: Power off the DVR and reboot it, then it will upgrade automatically. Or in the menu Menu -> System -> Update, touch OK to confirm to upgrade. Both methods can start the upgrade process.

Step 4: After When “Update success!” shows, unplug the USB disk or SD card with upgrade package, then DVR will reboot automatically.

Note: If using “dvxxx_upgrade_never_rename” package to upgrade, we must unplug the USB disk or SD card when “ update success!” is shown on the screen, or else the DVR will go into infinite loop of upgrade and will not boot up. SOLUTION: Unplug the USB disk or SD card with upgrade package, and then DVR will stop the upgrade process and boot up successfully.

 Remote upgrade Step 1：DVR connects to server.

Step 2：Open the Windows client and log in.

Step 3：Find the license number of the target DVR device in the device list of the client, right click and select “Update” to open the Batch Upgrades interface. If you

need to upgrade more than one device, you can click the Add button to select other devices. The selected ones will be disp layed on the dev ice list to upgrade. I f you want to remove devices from the list, please select them and click the Del button.

Step 4 :Select the device to upgrade, and then click the Browser button to select the upgrade package “dvxxx_upgrade_201xxxxxxxxx”. Note: For remote upgrade the package can’t be named as “dvxxx_upgrade_never_rename”.("xxx" in the "dvxxx_upgrade_never_rename" is the corresponding product model number)

Step 5: Click the Start button to upload the upgrade package. When uploading is finished, the device will start to upgrade automatically. If it is failed to upload, the reason of failure will be displayed in t he R emark column in the list.

11.9 Configuration

Configuration Import: Import t he configuration in formation fr om USB memory flash devices.

Configuration Export: Export Log t o USB memory flash devices.

Factory Default: Press RESET to restore factory settings.

11.10 System Info

System Info：Software version number.

12. FAQ

1) The system can’t start up?

Check power connection. Please follow the steps below to check the power connection:

1. Check the input power: if the power wire is connected correctly, if the ground wire is connected to the battery, and if the fuse on the power wire is in good condition.

2. Check if the voltage of the ACC signal wire is higher than 6 V.

3. Check if he input voltage of the dev ice is hig her than the shutdow n voltage s et on the screen of HD DVR.

2) The HD DVR restarts uninterruptedly?

Please follow the steps below to check it :

1. Check if the supply voltage of DVR is insufficient. If it is lower than the start-up

voltage of the device, the device would restart repeatedly.

2. Restart HD DVR to see if it can work proper ly this time.

3) Unable to recognize disks？

1. Check if the disk itself is in good condition and make sure that it is installed and

of fine contact.

2. The disk has been formatted by DVR.

3. Restart DVR to see if it can work properly t his t ime.

4) Unable to recognize cameras？

1. Make sure the camera is intact and the co nnection is correct.

2. Refit all wires (e.g,DB44 wire & extended wires) between cameras and t he

device .

3. Restart DVR to see if it can work properly this time.

5) GPS anomaly？

Check if the GPS antenna is properly installed.

13. APPENDIX

APPENDIXⅠ：Abbreviation & Description

Rec. Record SD Secure Digital Memory Card

G-sensor Accelerometer sensor USB Universal Serial Bus

GPS Global Positioning System DB44

Wi-Fi WIreless-FIdelity DB26

Cam Camera ALM Alarm

AVI Audio Video Interleaved VLOSS Video Loss

OSD On-Screen Display COMM Communication

APN Access Point Name ERR Error

DHCP

SSID Service Set Identifier MMSHOW

IP Internet Protocol FTP File Transfer Protocol

MAC Media Address Control DVR Digital Video Recorder

Dynamic Host Configuration

MEM Memory

Protocol

44PIN connector, A/V Input,

Output.IO/ALARM Output

26PIN connector, Alarm

Input/RS232/RS485

Media Player

RSSI

SSD Solid State Drive SYS System

LED Light Emitting Diode

Received Signal Strength

IR Infrared Radiation

Indication

APPENDIXⅡ：Accessories

NULL

Test Read

Test Write

MTFDDAK960

Typical

(MB/s)

Typical

(MB/s)

Capacity Interface

(MB/s)

Standard

Test Read/Write, Update software,

SDHC

Standard

Test Read/Write, Update software,

SDHC

Standard

Test Read/Write,

software,

APPENDIXⅢ：Compatibility Storage List

 SATA 3.0 SSD

Brand Name

Model Name

SIZE

(inch)

Flash

Capacity Interface

Type

Speed (MB/s)

Toshiba HDTS812 2.5 TLC 120G SATA3 98.0 119.7

Micron

TCC

2.5 TLC 960G SATA3 67.4 73.8

Samsung MZ-750120 2.5 TLC 120G SATA3 94.6 100.9 Samsung MZ-75E500 2.5 TLC 500G SATA3 72.5 124.2

Samsung

MZ-7KE1T0B

2.5 MLC 1T SATA3 64.9 77.4

SanDisk SDSSDA-120G 2.5 SLC 120G SATA3 99.6 70.5

Toshiba

THNSNJ256G

CSU

THNSNJ512G

CSU

2.5 MLC 256G SATA3 -- --

2.5 MLC 512G SATA3 -- --

Toshiba Q300PRO 2.5 MLC 1T SATA3 -- --

 SD Card

Test Brand Name

Model Name

Card Type

Read

Speed

Write

Speed

(GB)

Hot

Plug

Read

Speed

Test

Write

Speed

Speed (MB/s)

Remarks

Lexar

SanDisk

Lexar 128G

633X

SDXXG-032G-Z

N4IN

SDSDUNC-128

G-ZN6IN

SDXC UHS-I

95 45 128

95 90 32

80 75

128

OK 7.1 9.4

OK 9.2 12.6

OK 7.4 11.5

HotPlug

Update

HotPlug

TOSHIBA

Standard

Test Read/Write, Update software,

Standard

Test Read/Write, Update software,

Standard

Test Read/Write, Update software,

Transcend 64GB

Standard

Test Read/Write, Update software,

Transcend 32GB

Standard

Test Read/Write, Update software,

Transcend 64GB

Standard

Test Read/Write, Update software,

Standard

Test Read/Write, Update software,

THN-N302R032

0C4

SDHC

90 40 32

6.5 10.1 HotPlug

TOSHIBA

Transcend

THN-N302R064

0C4

THN-N302R012

80C4

UHS-I U3

UHS-I 600X SD

Transcend

128GB UHS-I U3

SDHC

SDXC UHS-I

SDHC

90 40 64

90 40 128

95 60 64

90 40 32

90 40 64

95 60 128

OK 7.2 9.3

OK 7.3 10.6

OK 6.9 7.5

OK 6.0 6.3

OK 7.1 9.0

7.8 6.2 HotPlug

HotPlug

DV426/DV426-4G

Axis DV426, DV426-4G Instruction Manual

Specifications and Main Features

Frequently Asked Questions

User Manual