Axis 5470e User Manual
AXIS 5470e User’s Guide 1
AXIS 5470e
User’s Guide
2
AXIS 5470e User’s Guide
Safety notices
Take some time to read through the safety notices before installing the AXIS 5470e. Please observe all safety markings and
instructions when using this product.
Warning! - must be observed to avoid bodily injuries.
Caution! - must be observed to avoid loss of data or damage to your equipment.
Important: - must be observed to avoid operational impairment.
Do not proceed any of the above notices, until you have fully understood the implications.
Electromagnetic Compatibility (EMC) USA - This equipment generates and radiates radio frequency energy and if not
installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been
tested and found to comply with the limits for a Class A computing device pursuant to Subpart B of Part 15 of FCC rules,
which are designed to provide reasonable protection against such interference when operated in a commercial environment.
Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will
be required to take whatever measures may be required to correct the interference. Shielded cables should be used with this
model to ensure compliance with the Class A limits.
Europe - This digital equipment fulfils the requirements for radiated emission according to limit B of EN55022/1998 and the
requirements for immunity according to EN55024/1998 residential, commercial, and light industry (Compliance is not valid
for unshielded network and printer cables).
Liability - Every care has been taken in the preparation of this manual; if you detect any inaccuracies or omissions, please
inform your local Axis office. Axis Communications AB cannot be held responsible for any technical or typographical errors
and reserves the right to make changes to the product and manuals without prior notice. Axis Communications AB makes no
warranty of any kind with regard to the material contained within this document, including, but not limited to, the implied
warranties of merchantability and fitness for a particular purpose. Axis Communications AB shall not be liable nor
responsible for incidental or consequential damages in connection with the furnishing, performance or use of this material.
Axis’ Trademarks - ThinWizard.
Other Trademark Acknowledgments - Adobe Acrobat Reader, Apple, Ethernet, EtherTalk, IBM, LAN Manager, LAN Server,
Macintosh, Microsoft, Novell NetWare, OS/2, OS/400, AS/400, TokenTalk, UNIX, Windows, are registered trademarks of the
respective holders.
Support Services - Should you require technical assistance, please contact your Axis dealer. If your questions cannot be
answered immediately, your Axis dealer will forward your queries through the appropriate channels to ensure you a rapid
response.
If you are connected to Internet, you can find on-line manuals, technical support, software updates, application software,
corporate information, etc., on any of the locations listed below.
WWW:
http://www.axis.com
USERS GUIDE AXIS 5470e EN Revision 1.3
Part No: 19746 Date: November 2002
Copyright © Axis Communications AB, 2002
AXIS 5470e User’s Guide 3
Table of Contents
Safety notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
The AXIS 5470e Network Print Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Hardware Inventory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installation Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Connecting the Printer to the Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Setup and Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Assigning an IP address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Manual IP address assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Setting the IP address using AXIS IP JumpStarter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Setting the IP address using arp/ping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
AS/400 SNA Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
The AS/400 Host System Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Configuring the AXIS 5470e . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Verifying the Communication Link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
AS/400 TN5250E Printing (SCS over IP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
The AS/400 Host System Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Configuring the AXIS 5470e . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Verifying the Communication Link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
AS/400 or Mainframe IPDS over PPR/PPD Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Configuring the AS/400 Host System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Configuring the Mainframe Host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Configuring the AXIS 5470e . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Verifying the Communication Link (AS/400) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Mainframe SNA Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Configuring the Mainframe Host System for SNA Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Configuring the AXIS 5470e for SNA Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Verifying the Communication Link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Mainframe TN3270E Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Configuring the Mainframe host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Configuring the AXIS 5470e . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Setting up the TN3270E server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Verifying the Communication Link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Setup for Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Installing Printers in Windows 2000/XP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Installing Printers in Windows 95/98/NT/Me . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Setup for NetWare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Setup using NDPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Setup using Queue-based printing over IP/IPX in PSERVER Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Setup for Queue-based printing over IPX/SPX (Remote Printer Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Setup for Macintosh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Mac OS X . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
AppleTalk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Setup for UNIX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
IPP Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Management and configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Configuration overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Using a Web Browser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Using AXIS ThinWizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
AS/400 and Mainframe Parameter Checklist 50
4
AXIS 5470e User’s Guide
Product Overview
The AXIS 5470e is a LAN attached multiprotocol print server that prints IBM and ASCII
data streams to any ASCII printer. Supporting IBM Mainframes, AS/400, NetWare, UNIX,
LAN Server Manager, Windows, OS/2 and Apple EtherTalk, this product is ideal for IBM
Mainframe and AS/400 sites that are migrating from pure IBM networks to LAN
environments.
A more comprehensive description of the AXIS 5470e is presented in the AXIS 5470e
User’s Manual which is available from the Axis Web site at http://www.axis.com
The AXIS 5470e Network Print Server
LPT1 Printer Connector
Ethernet Connector
10baseT/100baseTX
Power Supply
Connector
Power Indicator
Test Button
Network Indicator
AXIS 5470e User’s Guide 5
Hardware Inventory
Unpack and check all the items using the following check list. Contact your dealer if
anything is missing or damaged. All packing materials are recyclable.
AXIS 5470e Copier IPDS SNA TCP/IP
Part no 0096-021-01 0096-007-01 0096-013-01 0096-001-01
SNA support
X X X
IPDS support
SCS support
3270DS support
TN3270E
TN5250E
Digital Copier Support
Power Supply Type (PS-B)
Optional accessories Description Part Number
Cables
Ribbons
Kits
Centronics to Mini-Centronics Cable 16453
Printer Cable Extension 13522
Self-adhesive velcro ribbons 13282 and 13283
Flash Loading Kit 0041-4
X X
X X X X
X X X X
X X X X
X X X X
X
Europe 13267
UK 13268
Australia 13269
USA 13270
Japan 13936
Media Title Revision
CD
Printed Materials
AXIS Network Product CD 1.0 or later
AXIS 5470e User’s Guide 1.3 or later
6
AXIS 5470e User’s Guide
Product Model Summary
The AXIS 5470e is available in four versions, distinguished by the supported protocols,
data streams and Digital Copier support. The table below displays the specific functionality
for each version.
Note:
All models may not be available in all countries in which Axis operates. Please contact your local
dealer / sales representative for more information.
AXIS Network Product CD
The AXIS Network Product CD provides an easy-to-use electronic catalog, that includes
AXIS Utilities Software, Product Software, White Papers, User Documentations, etc. It is
compatible for use within all of the supported Axis computing environments.
You can view the contents of the AXIS Network Product CD via the HTML interface.
However, all documents presented on the CD are in PDF format.
Note:
If Adobe Acrobat Reader 3.0 is not installed on to your system, you can download Acrobat Reader
from the AXIS Network Product CD or Adobe’s web site at http://www.adobe.com
AXIS 5470e User’s Guide 7
Installation Overview
To get your print server up and running on your network, follow the instructions below:
• Connect the AXIS 5470e to your network and to your printer as described in
Connecting the Printer to the Network on page 8.
• Proceed to Setup and Configuration on page 9 to determine which setup procedures
that are relevant to your network environment.
• Proceed to Management and configuration on page 47 for information on supported
management and configuration tools.
8
AXIS 5470e User’s Guide
Connecting the Printer to the Network
Follow the instructions below to connect your printer to the network:
1. Switch off the printer and disconnect the AXIS 5470e external power supply.
2. Locate the serial number, found on the underside label of the AXIS 5470e, and write it
down. You will need this number during the network configuration.
Note:
Each AXIS 5470e is pre-configured with a unique node address that is identical to its serial number.
3. Connect the AXIS 5470e to your printer, either directly to the parallel printer port, or
using the optional printer cable extension with the optional velcro ribbons.
4. Connect your AXIS 5470e to the network using an appropriate network cable. If you are
connecting the AXIS 5470e to a Fast Ethernet network, the twisted pair cable must be of
category 5 or better.
5. Switch on the printer and connect the external power supply to the AXIS 5470e. The
power indicator lights up. If the network indicator starts to flash, the AXIS 5470e is
correctly connected to the network.
6. Press and release the test button on the AXIS 5470e to print a test page. If the
AXIS 5470e is correctly connected to the printer, a test page will be printed.
Proceed to Setup and Configuration on page 9 to determine which setup procedures that
are relevant to your network environment.
AXIS 5470e User’s Guide 9
Setup and Configuration
Refer to the table below to determine which setup procedures that are relevant to your
network environment and proceed to the appropriate section.
Environment Data
Streams
AS/400 SCS / IPDS SNA 1. Assigning an IP address, on page 10
SCS TN5250E (TCP/IP) 1. Assigning an IP address, on page 10
IPDS PPR/PPD (TCP/IP) 1. Assigning an IP address, on page 10
IBM
Mainframe
SCS / IPDS SNA 1. Assigning an IP address, on page 10
SCS / IPDS TN3270E (TCP/IP) 1. Assigning an IP address, on page 10
IPDS PPR/PPD (TCP/IP) 1. Assigning an IP address, on page 10
Network
Configuration
Actions
2. AS/400 SNA Printing, on page 14
2. AS/400 TN5250E Printing (SCS over IP), on page 18
2. AS/400 or Mainframe IPDS over PPR/PPD Printing, on
page 21
2. Mainframe SNA Printing, on page 26
2. Mainframe TN3270E Printing, on page 30
2. AS/400 or Mainframe IPDS over PPR/PPD Printing, on
page 21
NetWare TCP/IP and IPX/SPX 1. Assigning an IP address, on page 10
2. Setup for NetWare on page 36
Windows 95/98/NT/Me
2000/XP
Macintosh TCP/IP 1. Assigning an IP address, on page 10
UNIX TCP/IP 1. Assigning an IP address, on page 10
TCP/IP,
NetBIOS/NetBEUI
1. Assigning an IP address, on page 10
2. Setup for Windows, on page 35
2. Setup for Macintosh, on page 40
2. Setup for UNIX, on page 43
10
AXIS 5470e User’s Guide
Assigning an IP address
To establish communication with the TCP/IP network, an IP address must be assigned to
your AXIS 5470e. Choose an appropriate method from the table below:
Method: Server Required: Comment:
DHCP DHCP server Dynamic assignment of IP addresses
RARP RARP server Static assignment of IP addresses
BOOTP BOOTP server Static assignment of IP addresses
Auto-IP Windows environment Automatic assignment of IP addresses
All methods are enabled by default
If you are working in a Windows network with automatic IP address assignment, your
print server will obtain an IP address automatically when you connect it to the network.
Follow the instructions on this page to verify the IP address:
1. Open a web browser (e.g. Internet Explorer or Netscape Communicator).
2. In the Web browser’s Location/Address field, enter the print server’s IP address, found on
the test page (see Connecting the Printer to the Network on page 8) and press Enter.
3. If the Network Print Server web page appears in your Web browser, the IP address was
set automatically when you connected the AXIS 5470e to your network.
4. If the Network Print Server web page does not appear, you need to set the print server’s
IP address manually using one of the methods described in Manual IP address assignment
on page 11.
Notes:
• Use a Web browser with JavaScript support and Java enabled.
• The AXIS 5470e supports WINS (Windows Internet Name Service), which is recommended when set-
ting the IP address using DHCP in Windows environments.
• If you are working in a WINS/ DDNS network, you can access the print server’s web pages using its
default host name: In the Web browser’s Location/Address field, enter the default print server name
AXISxxxxxx (xxxxxx are the last six digits of the serial number, found on the print server’s underside
label). Example: If the serial number is 00 40 8c 18 16 36, type AXIS181636 and press Enter.
• DHCP, RARP and BOOTP can be used to set the IP address in UNIX, see the AXIS 5470e User’s Manual
for details.
• See the AXIS 5470e User’s Manual for installation instructions in a NetBIOS/NetBEUI environment.
The User’s Manual is available from the AXIS Network Product CD and from the Axis web site at
www.axis.com
• If you are working in a network that does not use dynamic IP address assignment, refer to Manual IP
address assignment on page 11 to assign an IP address to the print server manually.
AXIS 5470e User’s Guide 11
Manual IP address assignment
To establish communication with the TCP/IP network, an IP Address must be assigned to
your AXIS 5470e. Choose the appropriate method according to your network:
• AXIS IP JumpStarter™ is an easy-to-use Windows application that allows you to
assign an IP address to your AXIS 5900 and find Axis servers already installed in your
network. Refer to Setting the IP address using AXIS IP JumpStarter on page 12
instructions.
• arp/ping - use this method to set the IP address for each new device individually. This
method cannot be used over routers. Refer to Setting the IP address using arp/ping on
page 13 for instructions.
Note:
If you are using host names, you can map a unique host name to the IP address. Refer to your system
manuals for instructions on how this is performed on your system.
for
12
AXIS 5470e User’s Guide
Setting the IP address using AXIS IP JumpStarter
Use AXIS IP JumpStarter to set the IP address. Install AXIS IP JumpStarter which is
available from the AXIS Network Product CD or from the Axis web site at www.axis.com.
1. Select the required server from the serial number list in the IP JumpStarter dialog
window:
Server menu
2. From the Server menu, select Set IP Address.
3. Click the radio button that corresponds to your choice of IP setting method.
4. Click OK to save your settings.
5. Enter the server root password (by default set to pass), and click OK.
6. The AXIS 5470e will appear in the list with the assigned IP address.
7. To access the print server’s web pages, highlight the AXIS 5470e in the list and select
Server Home Page from the Server menu.
Note:
If your print server does not appear in the serial number list, refer to the AXIS IP JumpStarter online
help files or the AXIS 5470e User’s Manual which is available from the Axis web site at www.axis.com
AXIS 5470e User’s Guide 13
Setting the IP address using arp/ping
Refer to the appropriate section below to assign an IP address to your AXIS 5470e using
arp/ping:
Windows
Open a Command Prompt and enter the following syntax:
Syntax Example
1.
arp -s <Internet address> <Ethernet address>
2.
ping <Internet address>
3.
arp -d <Internet address>
The host will return reply from 192.168.3.191, or a similar message. This indicates
that the address has been set and that communication is established. You are now ready to
print using FTP or Reverse Telnet.
arp -s 192.168.3.191 00-40-8c-18-16-36
ping 192.168.3.191
arp -d 192.168.3.191
UNIX, Mac OS X
Open a Terminal and enter the following syntax:
Syntax Example
1.
arp -s <host name> <Ethernet address> temp
2.
ping <host name>
The host will return psname is alive, or a similar message. This indicates that the
address has been set and that communication is established. You are now ready to print
using FTP or Reverse Telnet.
Notes:
• The AXIS 5470e supports WINS (Windows Internet Name Service), which is recommended when setting the IP address using DHCP in Windows environments.
• The Ethernet Address is the same as the serial number, found on the print server’s underside label.
Enter the Ethernet Address in the same format as in the example above.
• Setting the IP address with arp and ping is only possible in the first ten minutes after re-booting
the print server.
• When you execute the ping command for the first time, you may experience a significantly longer
response time than usual.
arp -s psname 00:40:8c:18:16:36 temp
ping psname
• The arp command varies between different UNIX systems.
• You need root privileges on your UNIX system in order to execute the arp command and run axin-
stall (refer to the AXIS 5470e User’s Manual for more information).
• Some BSD type systems expect the host name and serial number in reverse order. Furthermore IBM
AIX systems will require the additional argument ether.
Example: arp -s ether <host name> <Ethernet Address> temp
14
AXIS 5470e User’s Guide
AS/400 SNA Printing
To establish communication with the TCP/IP network, you must assign an IP address to
your AXIS 5470e Print Server. Refer to Assigning an IP address on page 10.
Follow these instructions to configure your AS/400 and AXIS 5470e for SNA printing:
Step Action Described in
1.
2.
3.
Important!
SNA is not available for all AXIS 5470e models. Please refer to Product Model Summary on page 6.
If you are using OS/400 Version 3 Release 1 or higher, the AS/400 host in 5494 CU Mode will be configured
automatically. The information provided in this section describes this automated configuration procedure.
Configuring the AS/400 host system The AS/400 Host System Checklist on page 14
Configuring the AXIS 5470e Configuring the AXIS 5470e on page 16
Completing the installation Verifying the Communication Link on page 17
The AS/400 Host System Checklist
Note:
For future reference, enter the values below in the The AS/400 and Mainframe Parameter Checklist on
page 50.
1. Type DSPNETA on the AS/400 command line. For future reference, note the values of
the Local network ID and Default local location parameters. Press F3.
2. Type WRKLIND *ELAN to get a list of all line descriptions on the system. Type 5 in
front of the line description and press Enter.
3. Press F11 to display keywords.
4. For your future reference, note the values of the following parameters:
Local adapter address(ADPTADR) -andMaximum Controllers (MAXCTL)
Press Enter to view the active switched controllers display and verify that the number of
controllers does not exceed MAXCTL.
5. Press Enter repeatedly to display the SSAP list. Make sure there is at least one SSAP entry
dedicated for SNA. For your future reference, note the SSAP value for this entry.
6. Press Enter repeatedly to display the Autocreate controller (AUTOCRTCTL)
parameter. Ensure that the AUTOCRTCTL parameter is set to *YES. Press F3 to return to
the command line.
7. Type DSPSYSVAL QCHRID and press Enter. Note the code page for future reference.
Press F3.
AXIS 5470e User’s Guide 15
8. Type DSPSYSVAL QAUTOCFG and press Enter. Check that the parameter is set to
ON(1). Press F3.
9. Type DSPSYSVAL QAUTORMT and press Enter. Check that the parameter is set to
ON(1). Press F3.
10. Type DSPMODD QRMTWSC on the command line to check that the mode description
exists on the system. Press F3. Refer to the AXIS 5470e User’s Manual for information
regarding the QRMTWSC mode.
11. Type DSPUSRPRF QUSER. Make sure that the QUSER Status is *ENABLED and has
its Maximum Storage Allowed parameter set to *NOMAX. Press F3.
12. Use the command WRKCFGSTS *CTL xxxx*, where xxxx are the first 4 characters of
the AXIS 5470e LU Name, to delete any previously created Controller and Device
descriptions specific to your AXIS 5470e. Delete the Device Descriptions (indented text)
first and then the Controllers. (You will find the print server’s LU Name in the Parameter
List, under SNA menu. Press the print server’s test button twice to print the Parameter
List.)
If you experience problems with the installation procedure, please refer to the AXIS 5470e
User’s Manual which is available from the Axis Web site at http://www.axis.com
16
AXIS 5470e User’s Guide
Configuring the AXIS 5470e
Important!
To perform the instructions presented in this section, you must first assign an IP address to your AXIS 5470e using
one of the methods presented in Assigning an IP address on page 10.
After you have completed the procedures in The AS/400 Host System Checklist on page 14,
follow the instructions below to configure the AXIS 5470e for SNA printing in the AS/400
environment using a Web browser:
1. Start a Web browser, e.g. Internet Explorer or Netscape Communicator and enter the IP
address or the host name of the AXIS 5470e in the location field. Press Enter.
The internal Web pages of the AXIS 5470e will appear:
Note:
To protect the admin pages and the Configuration Wizard from unauthorized use, enter a password
(default Pass) in the Root Password field under admin | General Settings.
2. Click the Configuration Wizard for IBM sessions button.
3. Click the Add Session button. This will start the Configuration Wizard which is a
step-by-step guide through the required IBM configuration settings.
Loading...