Page 1
SHB101 Series
Intel® Core™2 Quad/Core™2 Duo
Celeron® Processor PICMG 1.3 Full-
Size
Single Board Computer
User’s Manual
Page 2
ii
Disclaimers
This manual has been carefully checked and believed to contain
accurate information. AXIOMTEK Co., Ltd. assumes no responsibility
for any infringements of patents or any third party’s rights, and any
liability arising from such use.
AXIOMTEK does not warrant or assume any legal liability or
responsibility for the accuracy, completeness or usefulness of any
information in this document. AXIOMTEK does not make any
commitment to update the information in this manual.
AXIOMTEK reserves the right to change or revise this document
and/or product at any time without notice.
No part of this document may be reproduced, stored in a retrieval
system, or transmitted, in any form or by any means, electronic,
mechanical, photocopying, recording, or otherwise, without the prior
written permission of AXIOMTEK Co., Ltd.
CAUTION
If you replace wrong batteries, it causes the danger of explosion. It is
recommended by the manufacturer that you follow the manufacturer’s
instructions to only replace the same or equivalent type of battery,
and dispose of used ones.
Copyright 2010 AXIOMTEK Co., Ltd.
All Rights Reserved
January 2010, Version A2
Printed in Taiwan
Page 3
iii
ESD Precautions
Computer boards have integrated circuits sensitive to static electricity.
To prevent chipsets from electrostatic discharge damage, please take
care of the following jobs with precautions:
Do not remove boards or integrated circuits from their anti-static
packaging until you are ready to install them.
Before holding the board or integrated circuit, touch an unpainted
portion of the system unit chassis for a few seconds. It
discharges static electricity from your body.
Wear a wrist-grounding strap, available from most electronic
component stores, when handling boards and components.
Trademarks Acknowledgments
AXIOMTEK is a trademark of AXIOMTEK Co., Ltd.
Windows® is a trademark of Microsoft Corporation.
Phoenix & AWARD are trademarks of Phoenix Technology Ltd.
IBM, PC/AT, PS/2, VGA are trademarks of International Business
Machines Corporation.
Intel® Core
TM
2 Quad/ Core
TM
2 Duo/Celeron® are trademarks of
Intel Corporation.
Winbond is a trademark of Winbond Electronics Corp.
Other brand names and trademarks are the properties and registered
brands of their respective owners.
Page 4
iv
Table of Contents
Disclaimers ............................................................................................................... ii
ESD Precautions .....................................................................................................iii
CHAPTER 1 INTRODUCTION......................................................................................... 1
1.1 Specifications.............................................................................................. 2
1.2 Utilities Supported....................................................................................... 3
1.3 I/O Bracket.................................................................................................. 4
CHAPTER 2 JUMPERS AND CONNECTORS ............................................................... 5
2.1 Board Dimensions....................................................................................... 5
2.2 Board Layout............................................................................................... 6
2.3 Jumper Settings.......................................................................................... 7
2.3.1 COM2 Mode Select Jumpers for RS-232/422/485 (JP1, JP2, JP3).... 7
2.3.2 CMOS Clear Jumper (JP6) ................................................................. 8
2.3.3 ATX Auto Power On/Off (JP7) ............................................................ 8
2.4 Connectors.................................................................................................. 9
2.4.1 ATX 4 Pin 12V In Connector (CN2)...................................................10
2.4.2 Front Panel Connector (CN3) ............................................................10
2.4.3 LAN1, LAN2 Link/Active LED Connectors (CN4, CN7)..................... 11
2.4.4 LAN1, LAN2 Speed LED Connectors (CN5, CN6)............................ 11
2.4.5 COM Port RS-232 Pin Assignment (COM1, COM2).........................12
2.4.6 COM2 RS-422/485 Pin Assignment.................................................. 12
2.4.7 CPU Fan Connector (FAN1).............................................................. 13
2.4.8 System Fan Connectors (FAN2, FAN3) ............................................13
2.4.9 Floppy Disk Port Connector (FDD1)..................................................13
2.4.10 Intel® HD Audio Digital Header (HDA1) .............................................14
2.4.11 PS/2 Keyboard, Mouse Connector (KB1, MS1).................................15
2.4.12 Ethernet RJ-45 Connectors (LAN1/LAN2) ........................................ 15
2.4.13 Parallel Port Connector (PRN1).........................................................16
2.4.14 SATA Connectors (SATA1~6) .......................................................... 17
2.4.15 USB Connectors (USB1/USB2) ........................................................ 17
2.4.16 USB Port Connector (USB3/USB4)...................................................18
2.4.17 DB15 CRT Connector (VGA1) .......................................................... 18
CHAPTER 3 HARDWARE INSTALLATION .................................................................19
3.1 Installing the Processor............................................................................. 19
3.2 Installing the Memory................................................................................ 24
CHAPTER 4 HARDWARE DESCRIPTION ................................................................... 25
4.1 Microprocessors........................................................................................ 25
4.2 BIOS .........................................................................................................25
4.3 System Memory ........................................................................................25
4.4 I/O Port Address Map ...............................................................................26
4.5 Interrupt Controller (IRQ) Map .................................................................. 27
CHAPTER 5 PHOENIX-AWARD BIOS UTILITY .......................................................... 29
5.1 Entering Setup .......................................................................................... 29
5.2 Control Keys..............................................................................................30
Page 5
v
5.3 Getting Help..............................................................................................30
5.4 The Main Menu.........................................................................................31
5.5 Standard CMOS Setup Menu ................................................................... 32
5.6 Advanced BIOS Features ......................................................................... 35
5.7 Advanced Chipset Features...................................................................... 40
5.8 Integrated Peripherals ............................................................................... 42
5.9 Power Management Setup ........................................................................46
5.10 PnP/PCI Configuration Setup ................................................................... 50
5.11 PC Health Status ...................................................................................... 52
5.12 Frequency/Voltage Control........................................................................53
5.13 Load Fail-Safe Defaults............................................................................. 54
5.14 Load Optimized Defaults........................................................................... 55
5.15 Set Supervisor/User Password ................................................................. 56
5.16 Save & Exit Setup ..................................................................................... 57
5.17 Exit Without Saving...................................................................................58
CHPATER 6 INSTALLATION OF DRIVERS.................................................................60
6.1 Installing Chipset Driver ............................................................................60
6.2 Installing VGA Driver................................................................................. 63
6.3 Installing LAN Driver................................................................................. 66
APPENDIX A WATCHDOG TIMER...............................................................................70
APPENDIX B PCI IRQ ROUTING.................................................................................. 72
APPENDIX C CONFIGURING SATA FOR RAID FUNCTION ...................................... 74
APPENDIX D PICMG v1.3 INTERFACE DEFINITION..................................................86
Page 6
vi
MEMO
Page 7
SHB101 LGA775 Full-Size SBC User’s Manual
Introduction
1
CHAPTER 1
INTRODUCTION
The SHB101 PICMG 1.3 full-size Single Board Computer supports
LGA775 socket for Intel® Core™ 2 Quad / Core™ 2 Duo/Celeron®
processors with 45/65nm technology and FSB 800/1066/1333 MHz.
The board integrates Intel® Q35 and ICH9R chipset that delivers
outstanding system performance through high-bandwidth interfaces,
multiple I/O functions for interactive applications and various
embedded computing solutions. There are four 240-pin DDR2 DIMM
sockets for dual channel DDR2 667/800, maximum memory capacity
up to 8GB. The board also features dual Gigabit Ethernet, six serial
ATA ports at maximum transfer rate up to 3Gbs, and SATA RAID
0/1/5/10 by ICH9R. Ten USB 2.0 high speed compliant ports and
built-in Intel® HD Audio Digital Header (optional) can achieve the
best stability and reliability for industrial applications.
Page 8
SHB101 LGA775 Full-Size SBC User’s Manual
Introduction
2
1.1 Specifications
CPU
Intel
®
Core™ 2 Quad / Core™ 2 Duo/Celeron®
processors
System Chipset
Intel
®
Q35 and ICH9R
CPU Socket
LGA775 Socket
Front-Side Bus
800/1066/1333 MHz
BIOS
Phoenix-Award BIOS via SPI interface with socket
System Memory
Four 240-pin DDR2 DIMM sockets
Maximum up to 8GB DDR2 memory
Support DDR2 667/800 memory
L2 Cache: integrated in CPU
Onboard Multi-I/O
Parallel Port: one 26-pin 2.54 pitch box-header,
SPP/EPP/ECP supported
Serial Port: one for RS-232 (COM1) and one port for
RS-232/422/485 (COM2)
Floppy controller: supports two drives (1.44MB for each)
USB Interface
Ten USB ports compliant with USB Spec. Rev. 2.0 (Six
ports on SHB101, four ports to SHB connector-C golden
fingers)
VGA Controller
Chipset -- Intel
®
integrated Graphics Gen3.5 on Intel® Q35
supports 3D, 2D, video capabilities
Memory Size -- Intel
®
DVMT 128/256MB supported;
Page 9
SHB101 LGA775 Full-Size SBC User’s Manual
Introduction
3
preallocated memory for frame buffer option as 8MB
Resolution -- Analog output -- the analog port utilizes an
integrated 350MHz 24-bit RAMDAC that can directly drive a
standard progressive scan analog monitor up to a resolution
of 2048x1536 pixels with 32-bit color at 75 Hz
Analog Output Interface -- CRT from DAC output via 15-pin
D-Sub connector on the edge; CRT always ON supported
Ethernet
The LAN1/LAN2 is 82573L Ethernet controller support
10/100/1000 Mb/s
Dual PCI-Express x1 LAN
Serial ATA
Support Serial ATA/Serial ATA II
Six Serial ATA-II ports, 3GB/s performance and SATA RAID
0/1/5/10 by ICH9R
Audio
16-pin 2.54 pin-header (Intel
®
HD Audio Digital Header)
(optional)
Hardware Monitoring
Monitoring temperatures, voltages, and cooling fan status
Watchdog Timer
Reset Supported (1-255 level)
Dimensions
338mm x 126mm
NOTE All specifications and images are subject to change without
notice.
1.2 Utilities Supported
Intel
®
Q35 Utility and Drivers
VGA Drivers
Ethernet Utility and Drivers
RAID Utility
Page 10
SHB101 LGA775 Full-Size SBC User’s Manual
Introduction
4
1.3 I/O Bracket
Page 11
SHB101 LGA775 Full-Size SBC User’s Manual
Jumpers and Connectors
5
CHAPTER 2
JUMPERS AND CONNECTORS
2.1 Board Dimensions
Page 12
SHB101 LGA775 Full-Size SBC User’s Manual
Jumpers and Connectors
6
2.2 Board Layout
Page 13
SHB101 LGA775 Full-Size SBC User’s Manual
Jumpers and Connectors
7
2.3 Jumper Settings
Proper jumer settings configure the SHB101 to meet your application
purpose.
2.3.1 COM2 Mode Select Jumpers for RS-232/422/485
(JP1, JP2, JP3)
These jumpers select the COM2 port’s communication mode to
operate RS-232 or RS-422/485.
Description Function
Jumper Setting
RS-232
(Default)
JP1
JP2
JP3
RS-422
JP1
JP2
JP3
COM2
RS-485
JP1
JP2
JP3
Page 14
SHB101 LGA775 Full-Size SBC User’s Manual
Jumpers and Connectors
8
2.3.2 CMOS Clear Jumper (JP6)
You may need to use this jumper is to clear the CMOS memory if
incorrect BIOS settings.
Description Function
Jumper Setting
Normal
(Default)
JP6
CMOS
Clear
Clear
CMOS
JP6
2.3.3 ATX Auto Power On/Off (JP7)
When Jumper JP7 is set OPEN for AC power input, the system will be
automatically power ON without pressing soft power button; when JP7
is SHORT for AC power input, it is necessary to manually press soft
power button to make the system power ON.
Note This function is similar to the feature of Power On after
Power Failed, which is controlled by hardware circuitry
instead of BIOS.
Description Function
Jumper Setting
Disable
(Default)
JP7
ATX Auto
Power
On/Off
Enable
JP7
Page 15
SHB101 LGA775 Full-Size SBC User’s Manual
Jumpers and Connectors
9
2.4 Connectors
Connectors connect this board with other parts of the system. Loose or
improper connection might cause problems. Make sure all connectors
are properly and firmly connected.
Here is a summary table shows you all connectors on the board.
Connector Label Connector Label
ATX 4 Pin 12V In CN2 Floppy Connector FDD1
Front Panel Connector CN3 Parallel Port PRN1
LAN2 Link / Active LED CN4 Serial ATA Connectors SATA1~6
LAN2 Speed LED CN5 USB Connector USB1~4
LAN1 Speed LED CN6 DB15 CRT Connector VGA1
LAN1 Link / Active LED CN7 DDRII DIMM Sockets DDR1~4
Serial Port1 Connector COM1 PS/2 Mouse Connector
MS1
Serial Port2 Connector COM2
PS/2 Keyboard
Connector
KB1
CPU FAN Connector FAN1
Intel HD Audio Digital
Header
HDA1
System FAN Connector FAN2 LAN1 Connector LAN1
System FAN Connector FAN3 LAN2 Connector LAN2
Page 16
SHB101 LGA775 Full-Size SBC User’s Manual
Jumpers and Connectors
10
2.4.1 ATX 4 Pin 12V In Connector (CN2)
You can connect it to the ATX12V power supply for CPU Core Voltage.
Pin
Signal
1 GND
2 GND
3 +12V
4 +12V
CN2
2.4.2 Front Panel Connector (CN3)
Power LED
This 3-pin connector denoted as Pin 1 and Pin 5 connects the
system power LED indicator to such a switch on the case. Pin 1 is
assigned as +, and Pin 5 as -. The Power LED lights up when the
system is powered ON. Pin 3 is defined as GND.
External Speaker and Internal Buzzer Connector
Pin 2, 4, 6 and 8 can be connected to the case-mounted speaker
unit or internal buzzer. While connecting the CPU card to an
internal buzzer, please short pins 2-4; while connecting to an
external speaker, you need to set pins 2-4 to Open and connect the
speaker cable to pin 8 (+) and pin 2 (-).
ATX Power On/Off Button
This 2-pin connector denoted as Pin 9 and 10 connects the front
panel’s ATX power button to the CPU card, which allows users to
Page 17
SHB101 LGA775 Full-Size SBC User’s Manual
Jumpers and Connectors
11
control ATX power supply to be power on/off.
System Reset Switch
Pin 11 and 12 can be connected to the case-mounted reset switch
that reboots your computer instead of turning OFF the power switch.
It is a better way to reboot your system for a longer life of the
system’s power supply.
HDD Activity LED
This connection is linked to hard drive activity LED on the control
panel. LED flashes when HDD is being accessed. Pin 13 and 14
connect the hard disk drive to the front panel HDD LED, Pin 13
assigned as -, and Pin 14 as +.
2.4.3 LAN1, LAN2 Link/Active LED Connectors (CN4,
CN7)
Pin Signal
1 LED (+)
2 LED (-)
CN4, CN7
2.4.4 LAN1, LAN2 Speed LED Connectors (CN5, CN6)
Pin Signal
1 100, Low Active
2 + 3.3V
3 1000, Low Active
CN5, CN6
Page 18
SHB101 LGA775 Full-Size SBC User’s Manual
Jumpers and Connectors
12
2.4.5 COM Port RS-232 Pin Assignment (COM1, COM2)
The serial interface for the board consists of COM1 port (COM1)
support for RS-232, and COM2 (COM2) for RS-232/RS422/RS485.
Pin
Signal Pin
Signal
1
Data Carrier Detect
(DCD)
2
Data Set Ready (DSR)
3
Receive Data (RXD) 4 Request to Send (RTS)
5
Transmit Data (TXD) 6 Clear to Send (CTS)
7
Data Terminal Ready
(DTR)
8
Ring Indicator (RI)
9 Ground (GND) 10 Ground (GND)
COM1, COM2
2
4
6
1
3
5
7
8
9
10
2.4.6 COM2 RS-422/485 Pin Assignment
COM2 Serial Port 10-pin (Box-header) Connector Pin Assignment list
Signal Name
Pin #
RS-422 RS-485
1 TX- DATA2 No connector No connector
3 TX+ DATA+
4 No connector No connector
5 RX+ No connector
6 No connector No connector
7 RX- No connector
8 No connector No connector
9 GND GND
10 GND GND
Page 19
SHB101 LGA775 Full-Size SBC User’s Manual
Jumpers and Connectors
13
2.4.7 CPU Fan Connector (FAN1)
A CPU fan is always needed for cooling CPU heat. The CPU fan
connector FAN1 provides power to the CPU fan.
Pin
Signal
1 Ground
2 +12V
3 Rotation Detection
4
Speed Control
FAN1
2.4.8 System Fan Connectors (FAN2, FAN3)
You can connect the system cooling fan cable to FAN2/FAN3 for
system cooling fan power.
Pin Signal
1 GND
2 +12V
3 Rotation Detection
FAN2, FAN3
2.4.9 Floppy Disk Port Connector (FDD1)
The board provides a 34-pin header type connector, FDD1, supporting
up to two floppy drives. The floppy drives may be any one of the
following types: 5.25" 360KB/1.2MB and 3.5" 720KB/1.44MB/2.88MB.
Pin
Signal Pin
Signal Pin
Signal
1 GND 2 Drive Density Select 3 GND
4 No connector 5 GND 6 No connector
7 GND 8 Index# 9 GND
10 Motor enable A# 11 GND 12 No connector
13 GND 14 Drive select A# 15 GND
16 No connector 17 GND 18 Direction#
19 GND 20 STEP# 21 GND
22 Write data# 23 GND 24 Write gate#
25 GND 26 Track 0 # 27 GND
Page 20
SHB101 LGA775 Full-Size SBC User’s Manual
Jumpers and Connectors
14
Pin
Signal Pin
Signal Pin
Signal
28 Write protect# 29 No connector 30 Read data#
31 GND 32 Head selection# 33 No connector
34 Disk change#
FDD1
2.4.10 Intel® HD Audio Digital Header (HDA1)
Pin
Signal Pin
Signal
1 BCLK 2 GND
3 RST# 4 VCC3
5 SYNC 6 GND
7 SDOUT 8 VCC3
9 SDI0 10 +12V
11 No connector
13 No connector 14 3VDUAL
15 No connector 16 GND
HDA1
Page 21
SHB101 LGA775 Full-Size SBC User’s Manual
Jumpers and Connectors
15
2.4.11 PS/2 Keyboard, Mouse Connector (KB1, MS1)
The board provides the Keyboard (KB1)/ Mouse (MS1) interface with a
5-pin connector.
Pin
Signal
1
Clock
2
DATA
3
No connector
4
GND
5
VCC
KB1/MS1
2.4.12 Ethernet RJ-45 Connectors (LAN1/LAN2)
The RJ-45 connectors LAN1 and LAN2 are for Ethernet. To connect
the board to 100-Base-T or 1000-Base-T hub, just plug one end of the
cable into LAN1 and connect the other end (phone jack) to a 100Base-T hub or 1000-Base-T hub.
Pin
Signal
1
Tx+ (Data transmission positive)
2
Tx- (Data transmission negative)
3
Rx+(Data reception positive)
4
RJ-1(For 1000 base T-Only)
5
RJ-1(For 1000 base T-Only)
6
Rx- (Data reception negative)
7
RJ-1(For 1000 base T-Only)
8
RJ-1(For 1000 base T-Only)
A
Active LED
B
Speed LED
LAN1/LAN2
12345678
A B
Page 22
SHB101 LGA775 Full-Size SBC User’s Manual
Jumpers and Connectors
16
2.4.13 Parallel Port Connector (PRN1)
Print Port Connector [Default]
This board has a multi-mode parallel port to support:
1. Standard Mode:
IBM PC/XT, PC/AT and PS/2 are compatible with bi-directional
parallel port.
2. Enhanced Mode:
Enhance parallel port (EPP) is compatible with EPP 1.7 and EPP
1.9 (IEEE 1284 compliant).
3. High Speed Mode:
Microsoft and Hewlett Packard extended capabilities port (ECP) is
IEEE 1284 compliant.
Pin
Signal Pin
Signal
1 Strobe# 2 Auto Form Feed#
3 Data 0 4 Error#
5 Data 1 6 Initialize#
7 Data 2 8 Printer Select In#
9 Data 3 10 GND
11 Data 4 12 GND
13 Data 5 14 GND
15 Data 6 16 GND
17 Data 7 18 GND
19 Acknowledge# 20 GND
21 Busy 22 GND
23 Paper Empty# 24 GND
25 Printer Select 26 GND
PRN1
2
4
6
1
3
5
7 8
9
11
13
15
10
12
14
16
17
19
21
23
25
18
20
22
24
26
Page 23
SHB101 LGA775 Full-Size SBC User’s Manual
Jumpers and Connectors
17
2.4.14 SATA Connectors (SATA1~6)
These SATA connectors are for high-speed SATA interface ports and
they can be connected to hard disk devices.
Pin
Signal
1 GND
2 SATA_TX+
3 SATA_TX-
4 GND
5 SATA_RX-
6 SATA_RX+
7 GND
SATA1~6
2.4.15 USB Connectors (USB1/USB2)
The 10-pin standard Universal Serial Bus (USB) connectors, USB1/2,
on this board are for installing versatile USB interface peripherals.
Pin Signal Pin
Signal
1 USB 2 USB
3 USB2- 4 USB3-
5 USB2+ 6 USB3+
7 GND 8 GND
9 GND 10 GND
USB1
Pin Signal Pin
Signal
1 USB 2 USB
3 USB4- 4 USB5-
5 USB4+ 6 USB5+
7 GND 8 GND
10 GND
USB2
Page 24
SHB101 LGA775 Full-Size SBC User’s Manual
Jumpers and Connectors
18
2.4.16 USB Port Connector (USB3/USB4)
The 4-pin standard Universal Serial Bus (USB) port connector on the
board is for the installation of peripherals supporting the USB interface.
Pin
Signal
1 USB POWER
2 USB -
3 USB +
4 GND
USB3/4
2.4.17 DB15 CRT Connector (VGA1)
VGA1 is a DB15 connector commonly used for the CRT Monitor.
Pin
Signal Pin
Signal Pin
Signal
1 Red 2 Green 3 Blue
4 NC 5 GND 6 DETECT
7 GND 8 GND 9 VCC
10 GND 11 NC 12 DDC DATA
13
Horizontal Sync 14 Vertical Sync 15 DDC CLK
VGA1
Page 25
SHB101 LGA775 Full-Size SBC User’s Manual
Hardware Installation
19
CHAPTER 3
HAREDWARE INSTALLATION
Before installing the processor, please access Intel® website for more
detailed information http://www.intel.com .
3.1 Installing the Processor
The LGA775 processor socket comes with a cover to protect the processor.
Please install the processor into the CPU socket step by step as below:
Hold the hook (A) of the lever and push it down.
Pull the lever (B) asisde to unlock the cover.
Page 26
SHB101 LGA775 Full-Size SBC User’s Manual
Hardware Installation
20
Remove the plastic cap (E) from the cover.
Open the cover (C), you
can see the contact.
Be careful not to touch the
contact (D).
Page 27
SHB101 LGA775 Full-Size SBC User’s Manual
Hardware Installation
21
Place the CPU down into the socket. Be careful not to touch the
contact.
Hold the edges of the CPU, and orientate it as the marked direction (G)
down into the socket to match the (H) and (F) locations.
Page 28
SHB101 LGA775 Full-Size SBC User’s Manual
Hardware Installation
22
Slightly push down the cover and hook the lever (I~J). The CPU is
completely locked.
Orientate the CPU cooling fan to fixing holes on the board.
Page 29
SHB101 LGA775 Full-Size SBC User’s Manual
Hardware Installation
23
Screw the CPU cooling fan onto the board.
Make sure the CPU fan is plugged to the CPU fan connector.
Page 30
SHB101 LGA775 Full-Size SBC User’s Manual
Hardware Installation
24
3.2 Installing the Memory
The board supports four 240-pin DDR2 DIMM memory sockets with
maximum memory capacity up to 8GB.
Please follow steps below to install the memory modules:
1 Push down latches on each side of the DIMM socket.
2 Align the memory module with the socket that notches of
memory module must match the socket keys for a correct
intallation.
3 Install the memory module into the socket and push it firmly
down until it is fully seated. The socket latches are levered
upwards and clipped on to the edges of the DIMM.
4 Install any remaining DIMM modules.
Page 31
SHB101 LGA775 Full-Size SBC User’s Manual
Hardware Description
25
CHAPTER 4
HARDWARE DESCRIPTION
4.1 Microprocessors
The SHB101 Series supports Intel® Core™ 2 Quad / Core™ 2
Duo/Celeron® processors, which make your system operated under
Windows® XP and Linux environments. The system performance
depends on the microprocessor. Make sure all correct settings are
arranged for your installed microprocessor to prevent the CPU from
damages.
4.2 BIOS
The SHB101 Series uses Phoenix-Award Plug and Play BIOS with a
single 8Mbit SPI Flash.
4.3 System Memory
The SHB101 Series supports four 240-pin DDR2 DIMM sockets for a
maximum memory of 8GB DDR2 SDRAMs. The memory module can
come in sizes of 64MB, 128MB, 256MB, 512MB, 1GB and 2GB.
Page 32
SHB101 LGA775 Full-Size SBC User’s Manual
Hardware Description
26
4.4 I/O Port Address Map
The Intel® Core™ 2 Quad / Core™ 2 Duo/Celeron® CPUs can
communicate via I/O ports. There are total 1KB port addresses
available for assignment to other devices via I/O expansion cards.
Address Devices
000-01F DMA controller #1
020-02D
024-025
028-029
02C-02D
Interrupt controller #1
02E-02F Forwarded to LPC(LPC Super I/O )
030-031
034-035
038-039
03C-03D
Interrupt controller #2
040-043
050-053
Timer/Counter (8254)
060 Forwarded to LPC (Microcontroller)
061 NMI
062-066 Forwarded to LPC (Microcontroller)
070-077 Real time clock, NMI
080-091 DMA page register
092 Processor I/F(Reset Generator)
093-09F DMA page register
0A0-0BF Interrupt controller #2
0C0-0DF DMA controller #2
0F0 Processor I/F
0F8-0FF Math processor
170-177 Forward to SATA (SATA Controller)
1F0-1F7 Forward to SATA (SATA Controller)
376 Forward to SATA(SATA Controller)
378-37F Parallel Port (LPT)
380-38F SDLC #2
3A0-3AF SDLC #1
3B0-3BF MDA video card
(to be continued)
Page 33
SHB101 LGA775 Full-Size SBC User’s Manual
Hardware Description
27
Address Devices
3C0-3CF EGA card
3D0-3DF CGA card
3F6 Forward to SATA(SATA Controller)
3F8-3FF Serial port #1 (COM1)
2F8-2FF Serial port #2 (COM2)
4.5 Interrupt Controller (IRQ) Map
The SHB101 Series is a 100% PC compatible control board. It
consists of 16 interrupt request lines, and four out of them can be
programmable. The mapping list of the 16 interrupt request lines is
shown as the following table.
IRQ Parity check error
IRQ0 System Timer Output
IRQ1 Keyboard
IRQ2 Interrupt rerouting from IRQ8 through IRQ15
IRQ3 Serial port #2
IRQ4 Serial port #1
IRQ5 PCI Device Share
IRQ6 Floppy Disk Controller
IRQ7 Parallel port
IRQ8 Real time clock
IRQ9 ACPI Controller
IRQ10 PCI Device Share
IRQ11 PCI Device Share
IRQ12 PS/2 Mouse
IRQ13 Math coprocessor
IRQ14 SATA Primary (Legacy Mode)
IRQ15 SATA Secondary (Legacy Mode)
Page 34
SHB101 LGA775 Full-Size SBC User’s Manual
Hardware Description
28
MEMO
Page 35
SHB101 LGA775 Full-Size SBC User’s Manual
Phoenix-Award BIOS Utility
29
CHAPTER 5
PHOENIX-AWARD BIOS UTILITY
The Phoenix-Award BIOS provides users with a built-in Setup program
to modify basic system configuration. All configured parameters are
stored in a battery-backed-up RAM (CMOS RAM) to save the Setup
information whenever the power is turned off.
5.1 Entering Setup
There are two ways to enter the Setup program. You may either turn
ON the computer and press <Del> immediately, or press the <Del>
and/or <Ctrl>, <Alt>, and <Esc> keys simultaneously when the
following message appears at the bottom of the screen during POST
(Power on Self Test).
TO ENTER SETUP PRESS DEL KEY
If the message disappears before you respond and you still want to
enter Setup, please restart the system to try it again. Turning the
system power OFF and ON, pressing the “RESET” button on the
system case or simultaneously pressing <Ctrl>, <Alt>, and <Del> keys
can restart the system. If you do not press keys at the right time and
the system doesn’t boot, an error message will pop out to prompt you
the following information:
PRESS <F1> TO CONTINUE, <CTRL-ALT-ESC> OR <DEL> TO ENTER SETUP
Page 36
SHB101 LGA775 Full-Size SBC User’s Manual
Phoenix-Award BIOS Utility
30
5.2 Control Keys
Up arrow
Move cursor to the previous item
Down arrow
Move cursor to the next item
Left arrow
Move cursor to the item on the left hand
Right arrow
Move to the item in the right hand
Esc key
Main Menu -- Quit and delete changes into CMOS
Status Page Setup Menu and Option Page Setup
Menu -- Exit current page and return to Main Menu
PgUp/“+” key
Increase the numeric value or make changes
PgDn/““ key
Decrease the numeric value or make changes
F1 key
General help, only for Status Page Setup Menu and
Option Page Setup Menu
(Shift) F2 key
Change color from total 16 colors. F2 to select color
forward, (Shift) F2 to select color backward
F3 key
Reserved
F4 key
Reserved
F5 key
Restore the previous CMOS value from CMOS, only
for Option Page Setup Menu
F6 key
Load the default CMOS value from BIOS default
table, only for Option Page Setup Menu
F7 key
Load the Setup default, only for Option Page Setup
Menu
F8 key
Reserved
F9 key
Reserved
F10 key
Save all the CMOS changes, only for Main Menu
5.3 Getting Help
Main Menu
The online description of the highlighted setup function is
displayed at the bottom of the screen.
Status Page Setup Menu/Option Page Setup Menu
Press <F1> to pop out a small Help window that provides the
description of using appropriate keys and possible selections for
highlighted items. Press <F1> or <Esc> to exit the Help Window.
Page 37
SHB101 LGA775 Full-Size SBC User’s Manual
Phoenix-Award BIOS Utility
31
5.4 The Main Menu
Once you enter the Phoenix-Award BIOS CMOS Setup Utility, the
Main Menu appears on the screen. In the Main Menu, there are several
Setup functions and a couple of Exit options for your selection. Use
arrow keys to select the Setup Page you intend to configure then press
<Enter> to accept or enter its sub-menu.
NOTE If your computer can not boot after making and saving
system changes with Setup, the Award BIOS will reset
your system to the CMOS default settings via its built-in
override feature.
It is strongly recommended that you should avoid changing the
chipset’s defaults. Both Award and your system manufacturer have
carefully set up these defaults that provide the best performance and
reliability.
Page 38
SHB101 LGA775 Full-Size SBC User’s Manual
Phoenix-Award BIOS Utility
32
5.5 Standard CMOS Setup Menu
The Standard CMOS Setup Menu displays basic information about
your system. Use arrow keys to highlight each item, and use <PgUp>
or <PgDn> key to select the value you want in each item.
Date
The date format is <day>, <date> <month> <year>. Press <F3> to
show the calendar.
day
It is determined by the BIOS and read only, from
Sunday to Saturday.
date
It can be keyed with the numerical/ function key, from 1
to 31.
month
It is from January to December.
year
It shows the current year of BIOS.
Time
This item shows current time of your system with the format
<hour> <minute> <second>. The time is calculated based on the
Page 39
SHB101 LGA775 Full-Size SBC User’s Manual
Phoenix-Award BIOS Utility
33
24-hour military-time clock. For example, 1 p.m. is 13:00:00.
IDE Channel 0/1/2/3 Master/IDE Channel 0/1 Slave
These items identify the types of each IDE channel installed in the
computer. There are 45 predefined types (Type 1 to Type 45) and
2 user’s definable types (Type User) for Enhanced IDE BIOS.
Press <PgUp>/<+> or <PgDn>/<> to select a numbered hard disk
type, or directly type the number and press <Enter>. Please be
noted your drive’s specifications must match the drive table. The
hard disk will not work properly if you enter improper information. If
your hard disk drive type does not match or is not listed, you can
use Type User to manually define your own drive type.
If selecting Type User, you will be asked to enter related
information in the following items. Directly key in the information
and press <Enter>. This information should be provided in the
documentation from your hard disk vendor or the system
manufacturer.
If the HDD interface controller supports ESDI, select “Type 1”.
If the HDD interface controller supports SCSI, select “None”.
If the HDD interface controller supports CD-ROM, select “None”.
CYLS.
number of cylinders
LANDZONE
landing zone
HEADS
number of heads
SECTORS
number of sectors
PRECOMP
write precom
MODE
HDD access mode
If there is no hard disk drive installed, select NONE and press
<Enter>.
Dive A /Drive B
The item identifies the types of floppy disk installed in the computer,
as drive A or drive B.
None No floppy drive installed
360K, 3.5 in 3.5 inch PC-type standard drive; 360Kb Mini ITXcity
1.2M, 3.5 in
3.5 inch AT-type high-density drive; 1.2MB Mini
ITXcity
720K, 3.5 in
3.5 inch double-sided drive; 720Kb Mini ITXcity
1.44M, 3.5 in
3.5 inch double-sided drive; 1.44MB Mini ITXcity
2.88M, 3.5 in
3.5 inch double-sided drive; 2.88MB Mini ITXcity
Video
Select the display adapter type for your system.
Page 40
SHB101 LGA775 Full-Size SBC User’s Manual
Phoenix-Award BIOS Utility
34
Halt On
This item determines whether the system will halt or not, if an error
is detected while powering up.
No errors
The system booting will halt on any errors detected.
(default)
All errors
Whenever BIOS detects a non-fatal error, the
system will stop and you will be prompted.
All, But
Keyboard
The system booting will not stop for a keyboard
error; it will stop for other errors.
All, But
Diskette
The system booting will not stop for a disk error; it
will stop for other errors.
All, But
Disk/Key
The system booting will not stop for a keyboard or
disk error; it will stop for other errors.
Press <Esc> to return to the Main Menu page.
Page 41
SHB101 LGA775 Full-Size SBC User’s Manual
Phoenix-Award BIOS Utility
35
5.6 Advanced BIOS Features
This section allows you to configure and improve your system, to set
up some system features according to your preference.
Page 42
SHB101 LGA775 Full-Size SBC User’s Manual
Phoenix-Award BIOS Utility
36
CPU Feature
Scroll to this item and press <Enter> to view the CPU Feature sub
menu.
Limit CPUID MaxVal
The CPUID instruction if some newer CPUs will return a
value greater than 3. The default is “Disabled“, because this
problem does not exist in the Windows series operating
systems. If you are using an operating system other than
Windows, this problem may occur. To avoid this problem,
you can enable this field to limit the return value to 3 or
lesser than 3.
Press <Esc> to return to the Advanced BIOS Features page.
Page 43
SHB101 LGA775 Full-Size SBC User’s Manual
Phoenix-Award BIOS Utility
37
Hard Disk Boot Priority
Scroll to this item and press <Enter> to view the sub menu to
decide the disk boot priority.
Press <Esc> to return to the Advanced BIOS Features page.
Page 44
SHB101 LGA775 Full-Size SBC User’s Manual
Phoenix-Award BIOS Utility
38
CD-ROM Boot Priority
Scroll to this item and press <Enter> to view the sub menu to
decide the CD-ROM boot priority.
Press <Esc> to return to the Advanced BIOS Features page.
Quick Power On Self Test
This option speeds up Power on Self Test (POST) after you turn
on the system power. If set as Enabled, BIOS will shorten or skip
some check items during POST. The default setting is “Enabled”.
Enabled
Enable Quick POST
Disabled
Normal POST
First/Second/Third Boot Device
These items let you select the 1st, 2nd, and 3rd devices that the
system will search for during its boot-up sequence. The wide range
of selection includes Floppy, LS120, ZIP100, HDD0~3, SCSI, and
CDROM.
Boot Other Device
This item allows users to enable or disable the boot device not
listed in the First/Second/Third boot devices option above. The
default setting is “Enabled”.
Page 45
SHB101 LGA775 Full-Size SBC User’s Manual
Phoenix-Award BIOS Utility
39
Boot Up NumLock Status
Set the the Num Lock status when the system is powered on. The
default value is “On”.
Security Option
This item allows you to limit access to the system and Setup, or
just to Setup. The default value is “Setup”.
System
If a wrong password is entered at the prompt, the system
will not boot, the access to Setup will be denied, either.
Setup
If a wrong password is entered at the prompt, the system
will boot, but the access to Setup will be denied.
NOTE To disable the security, select PASSWORD
SETTING at Main Menu and then you will be asked
to enter a password. Do not type anything, just
press <Enter> and it will disable the security. Once
the security is disabled, the system will boot and
you can enter Setup freely.
APIC Mode
Use this item to enable or disable APIC (Advanced Programmable
Interrupt Controller) mode that provides symmetric multiprocessing (SMP) for systems.
MPS Version Control For OS
This item specifies the version of the Multiprocessor Specification
(MPS). Version 1.4 has extended configuration tables to improve
support for multiple PCI bus configurations and provide future
expandability.
OS Select for DRAM >64MB
This item allows you to access the memory over 64MB in OS/2.
Press <Esc> to return to the Main Menu page.
Page 46
SHB101 LGA775 Full-Size SBC User’s Manual
Phoenix-Award BIOS Utility
40
5.7 Advanced Chipset Features
This section contains completely optimized chipset’s features on the
board that you are strongly recommended to leave all items on this
page at their default values unless you are very familiar with the
technical specifications of your system hardware.
PCI Express Root Port Func.
Scroll to this item and press <Enter> to view the sub menu to
decide the PCI Express Port.
Page 47
SHB101 LGA775 Full-Size SBC User’s Manual
Phoenix-Award BIOS Utility
41
Press <Esc> to return to the Advanced Chipset Features page.
VT-d
Use this item to enable or disable the VT-d to support the
remapping of I/O DMA transfers and device-generated interrupts.
** VGA Setting **
PEG/Onchip VGA Control
This setting allows you to select whether to use the onchip
graphics processor or the PCI Express card. When set to [Auto],
the BIOS will check if a PCI Express graphics card is installed or
not. If a PCI Express graphics card is detected, the board will boot
up using that card. Otherwise, it is defaulted to the onchip graphics
processor.
On-Chip Frame Buffer Size
Use this item to set the VGA frame buffer size.
DVMT Mode
DVMT (Dynamic Video Memory Technology) helps you select the
video mode.
DVMT/Fixed Memory Size
DVMT (Dynamic Video Memory Technology) allows you to select a
maximum size of dynamic amount usage of the video memory.
The system would configure the video memory dependent on your
application.
Press <Esc> to return to the Main Menu page.
Page 48
SHB101 LGA775 Full-Size SBC User’s Manual
Phoenix-Award BIOS Utility
42
5.8 Integrated Peripherals
This section allows you to configure your SuperIO Device, IDE
Function and Onboard Device.
OnChip IDE Device
Scroll to this item and press <Enter> to view the sub menu OnChip
IDE Device.
Page 49
SHB101 LGA775 Full-Size SBC User’s Manual
Phoenix-Award BIOS Utility
43
IDE HDD Block Mode
Block mode is also called block transfer, multiple
commands, or multiple sector read/write. If your IDE hard
drive supports block mode (most new drives do), select
Enabled for automatic detection of the optimal number of
block read/writes per sector the drive can support.
IDE DMA transfer access
Automatic data transfer between system memory and IDE
device with minimum CPU intervention. This improves data
throughput and frees CPU to perform other tasks.
IDE Primary/Secondary Master/Slave PIO
The four IDE PIO (Programmed Input/Output) fields let you
set a PIO mode (0-4) for each of the four IDE devices that
the onboard IDE interface supports. Modes 0 to 4 provide
successively increased performance. In Auto mode, the
system automatically determines the best mode for each
device.
IDE Primary/Secondary Master/Slave UDMA
Select the mode of operation for the IDE drive. Ultra DMA33/66/100/133 implementation is possible only if your IDE
hard drive supports it and the operating environment
includes a DMA driver. If your hard drive and system
software both support Ultra DMA-33/66/100/133, select Auto
to enable UDMA mode by BIOS.
SATA Mode
There are these options for you to set up SATA mode: IDE,
RAID or AHCI.
LEGACY Mode Support
Legacy mode support allows devices to function in an
operating environment that is not USB-aware.
Press <Esc> to return to the Integrated Peripherals page.
Page 50
SHB101 LGA775 Full-Size SBC User’s Manual
Phoenix-Award BIOS Utility
44
Super IO Device
Scroll to this item and press <Enter> to view the sub menu Super
IO Device.
Onboard FDC Controller
Select Enabled, if your system has a floppy disk controller
(FDC) installed on the system board and you want to use it.
If you install and-in FDC or the system has no floppy drive,
select Disabled in this field. Options: Enabled and Disabled.
Onboard Serial Port 1 / 2
Select an address and corresponding interrupt for the serial
port. Options: 3F8/IRQ4, 2E8/IRQ3, 3E8/IRQ4, 2F8/IRQ3,
Disabled, Auto.
Onboard Paralellel Port
This item allows you to determine the I/O address for
onboard parallel port. Options: 378H/IRQ7, 278H/IRQ5,
3BC/IRQ7 and Disabled.
Parallel Port Mode
Select an operating mode for the onboard parallel (printer)
port. Select Normal unless your hardware and software
require another mode in this field. Options: EPP1.9, ECP,
SPP, ECPEPP1.7, EPP1.7.
EPP Mode Select
Select EPP port type 1.7 or 1.9.
ECP Mode Use DMA
Page 51
SHB101 LGA775 Full-Size SBC User’s Manual
Phoenix-Award BIOS Utility
45
Select a DMA channel for the parallel port while using the
ECP mode.
PWRON After PWR-Fail
This item enables your computer to automatically restart or
return to its operating status.
Press <Esc> to return to the Integrated Peripherals page.
USB Device Setting
Scroll to this item and press <Enter> to view the sub menu USB
Device Setting.
Press <Esc> to return to the Integrated Peripherals page.
Onboard Lan Boot ROM
Use this item to enable or disable the Boot ROM function of the
onboard LAN chip when the system boots up.
Press <Esc> twice to return to the Main Menu page.
Page 52
SHB101 LGA775 Full-Size SBC User’s Manual
Phoenix-Award BIOS Utility
46
5.9 Power Management Setup
The Power Management Setup allows you to save energy of your
system effectively. It will shut down the hard disk and turn OFF video
display after a period of inactivity.
ACPI Function
This item allows you to enable/disable the Advanced Configuration
and Power Management (ACPI). The function is always “Enabled”.
ACPI Suspend Type
This item specifies the power saving modes for ACPI function. If
your operating system supports ACPI, such as Windows 98SE,
Windows ME and Windows 2000, you can choose to enter the
Standby mode in S1 (POS) or S3 (STR) fashion through the setting
of this field. Options are:
[S1 (POS)] The S1 sleep mode is a low power state. In this
state, no system context is lost (CPU or chipset) and
hardware maintains all system contexts.
[S3 (STR)] The S3 sleep mode is a lower power state where
the information of system configuration and open
applications/files is saved to main memory that remains
Page 53
SHB101 LGA775 Full-Size SBC User’s Manual
Phoenix-Award BIOS Utility
47
powered while most other hardware components turn off to
save energy. The information stored in memory will be used
to restore the system when a “wake up” event occurs.
Run VGABIOS if S3 Resume
When this item is set Auto, the system will run VGA BIOS if it is
reaumed from the S3 state.
Power Management
This option allows you to select the type (or degree) of power
saving for Doze, Standby, and Suspend modes. The table below
describes each power management mode:
Max Saving
It is maximum power savings, only available for SL
CPUs. The inactivity period is 1 minute in each
mode.
User Define
It sets each mode. Select time-out periods in the PM
Timers section.
Min Saving
It is minimum power savings. The inactivity period is
1 hour in each mode (except the hard drive).
Disabled Default value
Video Off Method
This setting determines the manner in which the monitor is blanked.
V/H
SYNC+Blank
It turns OFF vertical and horizontal synchronization
ports and writes blanks to the video buffer.
DPMS
Select this option if your monitor supports the Display
Power Management Signaling (DPMS) standard of the
Video Electronics Standards Association (VESA). Use
the supplied software
for your video subsystem to select
video power management values.
Blank Screen
The System only writes blanks to the video buffer.
Video Off In Suspend
This item defines if the video is powered down when the system is
put into suspend mode.
Suspend Type
If this item is set to the default Stop Grant, the CPU will go into Idle
Mode during power saving mode.
Suspend Mode
Page 54
SHB101 LGA775 Full-Size SBC User’s Manual
Phoenix-Award BIOS Utility
48
After the selected period of system inactivity (1 minute to 1 hour),
all devices except the CPU shut off. The default value is
“Disabled”.
Disabled System will never enter SUSPEND mode
1/2/4/6/8/10/
20/30/40
Min/1 Hr
Defines the continuous idle time before the system
entering SUSPEND mode.
If any item defined in (J) is enabled & active,
SUSPEND timer will be reloaded
HDD Power Down
If HDD activity is not detected for the length of time specified in
this field, the hard disk drive will be powered down while all other
devices remain active.
Soft-Off by PWR-BTTN
This option only works with systems using an ATX power supply. It
also allows users to define which type of soft power OFF sequence
the system will follow. The default value is “Instant-Off”.
Instant-Off
This option follows the conventional manner of system
performance when turning the power to OFF. InstantOff is a software power OFF sequence requiring the
power supply button is switched to OFF.
Delay 4 Sec.
Upon the system’s turning OFF through the power
switch, this option will delay the complete system
power OFF sequence approximately 4 seconds.
Within
this delay period, the system will temporarily enter into
the Suspend Mode enabling you to restart the system
at once.
Power On by Ring
This option allows the system to resume or wake up upon
detecting any ring signals coming from an installed modem. The
default value is “Enabled”.
** Reload Global Timer Events **
Global Timer (power management) events can prevent the system
from entering a power saving mode or can awaken the system from
such a mode.
HPET Support
Use this item to enable or disable HPET (High Precision Event
Timer), which is designed to have very fine-grained resolution, fast
Page 55
SHB101 LGA775 Full-Size SBC User’s Manual
Phoenix-Award BIOS Utility
49
access times, and support for aperiodic behavior.
Page 56
SHB101 LGA775 Full-Size SBC User’s Manual
Phoenix-Award BIOS Utility
50
HPET Mode
Use this item to configure the HPET (High Precision Event Timer)
mode.
Press <Esc> to return to the Main Menu page.
5.10 PnP/PCI Configuration Setup
This section describes the configuration of PCI (Personal Computer
Interconnect) bus system, which allows I/O devices to operate at
speeds close to the CPU speed while communicating with other
important components. This section covers very technical items that
only experienced users could change default settings.
PNP OS Installed
Select Yes if the system operating environment is Plug-and-Play
aware (e.g., Windows 95). The default value is “No”.
Init Display First
This item allows you to decide whether PCI Slot or AGP to be the
first primary display card.
Page 57
SHB101 LGA775 Full-Size SBC User’s Manual
Phoenix-Award BIOS Utility
51
Reset Configuration Data
Normally, you leave this item Disabled. Select Enabled to reset
Extended System Configuration Data (ESCD) when you exit Setup
or if installing a new add-on cause the system reconfiguration a
serious conflict that the operating system can not boot. Options:
Enabled, Disabled.
Resources Controlled By
The Award Plug and Play BIOS can automatically configure all
boot and Plug and Play-compatible devices. If you select Auto, all
interrupt request (IRQ), DMA assignment, and Used DMA fields
disappear, as the BIOS automatically assigns them. The default
value is “Manual”.
IRQ Resources
When resources are controlled manually, assign each system
interrupt to one of the following types in accordance with the type
of devices using the interrupt:
1. Legacy ISA Devices compliant with the original PC AT bus
specification, requiring a specific interrupt (such as IRQ4 for serial
port 1).
2. PCI/ISA PnP Devices compliant with the Plug and Play standard,
whether designed for PCI or ISA bus architecture.
The default value is “PCI/ISA PnP”.
DMA Resources
When resources are controlled manually, assign each system
DMA channel as one of the following types, depending on the type
of device using the interrupt:
Legcy ISA Devices compliant with the original PC AT bus
specification, requiring a specific DMA channel.
PCI/ISA PnP Devices compliant with the Plug and Play standard,
whether designed for PCI or ISA bus architecture.
The default value is “PCI/ISA PnP”.
PCI/VGA Palette Snoop
Some non-standard VGA display cards may not show colors
properly. This item allows you to set whether MPEG ISA/VESA
VGA Cards can work with PCI/VGA or not. When enabled, a
PCI/VGA can work with a MPEG ISA/VESA VGA card; when
disabled, a PCI/VGA cannot work with a MPEG ISA/VESA Card.
Page 58
SHB101 LGA775 Full-Size SBC User’s Manual
Phoenix-Award BIOS Utility
52
** PCI Express relative items **
Maximum Payload Size
When using DDR SDRAM and Buffer size selection, another
consideration in designing a payload memory is the size of the
buffer for data storage. Maximum Payload Size defines the
maximum TLP (Transaction Layer Packet) data payload size for
the device.
Press <Esc> to return to the Main Menu page.
5.11 PC Health Status
This section supports hardware monitering that lets you monitor those
parameters for critical voltages, temperatures and fan speed of the
board.
Current CPU Temperature
The current system CPU temperature will be automatically
detected by the system.
Current SYSTEM Temperature
Show you the current system1 temperature.
Page 59
SHB101 LGA775 Full-Size SBC User’s Manual
Phoenix-Award BIOS Utility
53
CPU FAN Speed
These optional and read-only items show current speeds in RPM
(Revolution Per Minute) for the CPU fan and chassis fan as
monitored by the hardware monitoring IC.
SYSTEM FAN1 Speed
Show you the current system fan1 temperature.
SYSTEM FAN2 Speed
Show you the current system fan1 temperature.
Vcore +3.3V/+5V/+12V/5VSB
Show you the voltage of +3.3V/+5V/+12V.
Press <Esc> to return to the Main Menu page.
5.12 Frequency/Voltage Control
CPU Clock Ratio Unlock
Use this item to unlock CPU multiplier.
CPU Clock Ratio
Use this item to select the CPU’s frequency.
Auto Detect PCI Clk
The enabled item can automatically disable the clock source for a
PCI slot without a module, to reduce EMI (ElectroMagnetic
Page 60
SHB101 LGA775 Full-Size SBC User’s Manual
Phoenix-Award BIOS Utility
54
Interference).
Spread Spectrum
If spread spectrum is enabled, EMI (ElectroMagnetic Interference)
generated by the system can be significantly reduced.
Press <Esc> to return to the Main Menu page.
5.13 Load Fail-Safe Defaults
When you press <Enter> on this item, a confirmation dialog box pops
out to show you such a message:
Please press “Y” to load default values that will be factory settings for
accomplishing the optimal performance of system operations.
Page 61
SHB101 LGA775 Full-Size SBC User’s Manual
Phoenix-Award BIOS Utility
55
5.14 Load Optimized Defaults
This option allows you to load your system configuration with default
values. These default settings are optimized to enable high
performance features.
To load CMOS SRAM with SETUP default values, please enter “Y”. If
not, please enter “N”.
Page 62
SHB101 LGA775 Full-Size SBC User’s Manual
Phoenix-Award BIOS Utility
56
5.15 Set Supervisor/User Password
You can set a supervisor or user password, or both of them. The
differences between them are:
1. Supervisor password: You can enter and change the options on
the setup menu.
2. User password: You can just enter, but have no right to change
the options on the setup menu.
When you select this function, the following message will appear at the
center of the screen to assist you in creating a password.
ENTER PASSWORD
Type a maximum eight-character password, and press <Enter>. This
typed password will clear previously entered password from the CMOS
memory. You will be asked to confirm this password. Type this
password again and press <Enter>. You may also press <Esc> to abort
this selection and not enter a password.
To disable the password, just press <Enter> when you are prompted to
enter a password. A message will confirm the password is getting
disabled. Once the password is disabled, the system will boot and you
can enter Setup freely.
PASSWORD DISABLED
When a password is enabled, you have to type it every time you enter
the Setup. It prevents any unauthorized persons from changing your
system configuration.
Additionally, when a password is enabled, you can also require the
BIOS to request a password every time the system reboots. This would
prevent unauthorized use of your computer.
You decide when the password is required for the BIOS Features
Setup Menu and its Security option. If the Security option is set to
“System”, the password is required during booting up and entry into the
Setup; if it is set as “Setup”, a prompt will only appear before entering
the Setup.
Page 63
SHB101 LGA775 Full-Size SBC User’s Manual
Phoenix-Award BIOS Utility
57
5.16 Save & Exit Setup
This section allows you to determine whether or not to accept your
modifications. Type “Y” to quit the setup utility and save all changes
into the CMOS memory. Type “N” to bring you back to the Setup utility.
Page 64
SHB101 LGA775 Full-Size SBC User’s Manual
Phoenix-Award BIOS Utility
58
5.17 Exit Without Saving
Select this option to exit the Setup utility without saving changes you
have made in this session. Type “Y”, and it will quit the Setup utility
without saving your modifications. Type “N” to return to the Setup
utility.
Page 65
SHB101 LGA775 Full-Size SBC User’s Manual
Phoenix-Award BIOS Utility
59
MEMO
Page 66
SHB101 LGA775 Full-Size SBC User’s Manual
Instalation of Drivers
60
CHPATER 6
INSTALLATION OF DRIVERS
The device driv ers are located on the Product Information CD-ROM
that comes with the SHB101 Series package. The auto-run function
of drivers will guide you to install the utilities and device drivers under
a Windows system. You can follow the onscreen instructions to install
these devices:
Chipset
VGA
LAN
6.1 Installing Chipset Driver
1. Run the SETUP.EXE program from the driver directory in
your driver CD. Click “Next” to next step.
Page 67
SHB101 LGA775 Full-Size SBC User’s Manual
Installation of Drivers
61
2. An Intel® License Agreement appears to show you the
important information. Click “Yes” to next step.
3. Please wait while running the following setup operations.
(3-1)
Page 68
SHB101 LGA775 Full-Size SBC User’s Manual
Instalation of Drivers
62
(3-2)
4. Click “Finish” to complete the setup process.
Page 69
SHB101 LGA775 Full-Size SBC User’s Manual
Installation of Drivers
63
5. You will be asked to reboot your computer when the
installation is completed. Please click “Yes, I want to restart
my computer now” if you don’t need to install any other
drivers. Otherwise, please click “No, I will restart my
computer later”, and go on next step.
6.2 Installing VGA Driver
1. Run the SETUP.EXE program from the driver directory in
your driver CD. Click “Next” to next step.
Page 70
SHB101 LGA775 Full-Size SBC User’s Manual
Instalation of Drivers
64
2. An Intel® License Agreement appears to show you the
important information. Click “Yes” to next step.
3. The message of Readme File Information appears to show
you the system requirements and installation information.
Please click “Next”.
Page 71
SHB101 LGA775 Full-Size SBC User’s Manual
Installation of Drivers
65
4. Please wait while running the following setup operations.
When this message appears, please click “Next”.
5. Click “Finish” to complete the setup process.
Page 72
SHB101 LGA775 Full-Size SBC User’s Manual
Instalation of Drivers
66
6. You will be asked to reboot your computer when the
installation is completed. Please click “Yes, I want to restart
my computer now” if you don’t need to install any other
drivers. Otherwise, please click “No, I will restart my
computer later”, and click “Finish” to complete the
installation.
6.3 Installing LAN Driver
1. Run the InstallShield Wizard for Network Connections from
the driver directory in your driver CD. Click “Next” to next
step.
Page 73
SHB101 LGA775 Full-Size SBC User’s Manual
Installation of Drivers
67
2. Click “Install” to start the installation.
3. Please wait while running the following installation operation.
Page 74
SHB101 LGA775 Full-Size SBC User’s Manual
Instalation of Drivers
68
4. Click “Finish” to complete the installation.
Note The Driver item [Wake on Directed Packet] default
is Enabled under Windows Vista.
Page 75
SHB101 LGA775 Full-Size SBC User’s Manual
Installation of Drivers
69
MEMO
Page 76
SHB101 LGA775 Full-Size SBC User’s Manual
Watchdog Timer
70
APPENDIX A
WATCHDOG TIMER
Watchdog Timer Setting
After the system stops working for a while, it can be auto-reset by the
Watchdog Timer. The integrated Watchdog Timer can be set up in the
system reset mode by program.
Using the Watchdog Function
Start
Un-Lock WDT
:O 2E 87 ; Un-lock super I/O
O 2E 87 ; Un-lock super I/O
Set WDT Funtion
O 2E 2D
O 2F 20
Select Logic device
O 2E 07
O 2F 08
Activate WDT
:O 2E 30
O 2F 01
Set Second or Minute
O 2E F5
O 2F N N=00 or 08(See below table)
Set base timer
:O 2E F6
O 2F M=00,01,02,…FF(Hex) ,Value=0 to 255
WDT counting
re-set timer :O 2E F6
O 2F M ; M=00,01,02,…FF(See below table)
Page 77
SHB101 LGA775 Full-Size SBC User’s Manual
Watchdog Timer
71
IF No re-set timer :WDT time-out, generate RESET
IF to disable WDT :O 2E 30
O 2F 00 ; Can be disable at any time
N=00
M= 00h: Time-out Disable
01h: Time-out occurs after 1 second
02h: Time-out occurs after 2 second
03h: Time-out occurs after 3 second
……………………….......................................
FFh: Time-out occurs after 255 second
N=08
M= 00h: Time-out Disable
01h: Time-out occurs after 1 minute
02h: Time-out occurs after 2 minutes
03h: Time-out occurs after 3 minutes
……………………….......................................
FFh: Time-out occurs after 255 minutes
Page 78
SHB101 LGA775 Full-Size SBC User’s Manual
PCI IRQ Routing
72
APPENDIX B
PCI IRQ ROUTING
PICMG PCI IRQ Routing
Device ID Slot Int
PCI Slot 0 31 0 BCDA
PCI Slot 1 30 1 CDAB
PCI Slot 2 29 2 DABC
PCI Slot 3 28 3 ABCD
Page 79
SHB101 LGA775 Full-Size SBC User’s Manual
PCI IRQ Routing
73
MEMO
Page 80
SHB101 LGA775 Full-Size SBC User’s Manual
Configuring SATA for RAID Function
74
APPENDIX C
CONFIGURING SATA FOR RAID
FUNCTION
Configuring SATA Hard Drive(s) for RAID
Function (Controller: Intel® ICH9R/DO DH only)
Please follow up the steps below to configure SATA hard drive(s):
(1) Install SATA hard drive(s) in your system.
(2) Enter the BIOS Setup to configure SATA controller mode and boot
sequence.
(3) Configure RAID by the RAID BIOS.
(4) Create a floppy disk for the SATA controller driver.
(5) Install the SATA controller driver during the OS installation.
Before you begin the SATA configuration, please prepare:
(a) Two SATA hard drives (to ensure optimal performance, it is
recommended that you use two hard drives with identical model
and capacity). If you do not want to create RAID with the SATA
controller, you may prepare only one hard drive.
(b) An empty formatted floppy disk
(c) Windows XP setup disk
(1) Installing SATA hard drive(s) in your system
Connect one end of the SATA signal cable to the rear of the SATA
hard drive, and the other end to available SATA port(s) on the
board. Then, connect the power connector of power supply to the
hard drive.
(2) Configuring SATA controller mode and boot sequence by the
BIOS Setup
You have to make sure whether the SATA controller is configured
correctly by system BIOS Setup and set up BIOS boot sequence
for the SATA hard drive(s).
Page 81
SHB101 LGA775 Full-Size SBC User’s Manual
Configuring SATA for RAID Function
75
(2)-1 Turn on your system and press the Del button to enter BIOS
Setup during running POST (Power-On Self Test).
Figure 1
Page 82
SHB101 LGA775 Full-Size SBC User’s Manual
Configuring SATA for RAID Function
76
(2)-2 Set CDROM for First Boot Device under the Advanced
BIOS Features menu to boot CD-ROM after system restarts
(Figure 2).
Figure 2
(2)-3 Save and exit the BIOS Setup.
(3) Configuring RAID by the RAID BIOS
Enter the RAID BIOS setup utility to configure a RAID array. Skip this
step and proceed to Section 4 if you do not want to create a RAID.
Page 83
SHB101 LGA775 Full-Size SBC User’s Manual
Configuring SATA for RAID Function
77
(3)-1 After the POST memory testing and before the operating
system booting, a message "Press <Ctrl-I> to enter
Configuration Utility" (as Figure 3) shows up, accordingly,
press <CTRL+ I> to enter the RAID BIOS setup utility.
Figure 3
(3)-2 After you press <CTRL+ I>, the Create RAID Volume screen
will appear (as Figure 4). If you want to create a RAID array,
select the Create RAID Volume option in the Main Menu and
press ENTER.
Figure 4
Page 84
SHB101 LGA775 Full-Size SBC User’s Manual
Configuring SATA for RAID Function
78
(3)-3 After entering the CREAT VOLUME MENU screen, you can
type the disk array name with 1~16 letters (letters cannot be
special characters) in the item “Name”. When finished, press
ENTER to select a RAID level (as Figure 5). There are three
RAID levels, RAID0, RAID1 and RAID5&RAID10. Select a
RAID level and press ENTER.
Figure 5
(3)-4 Set the stripe block size (as Figure 6). The KB is the standard
unit of stripe block size. The stripe block size can be 4KB to
128KB. After the setting, press ENTER for the array capacity.
Figure 6
Page 85
SHB101 LGA775 Full-Size SBC User’s Manual
Configuring SATA for RAID Function
79
(3)-5 After setting all the items on the menu, select Create
Volume and press ENTER (as Figure 7) to start creating the
RAID array.
Figure 7
(3)-6 When prompting the confirmation, press “Y“ to create this
volume, or “N“ to cancel the creation.
Figure 8
Page 86
SHB101 LGA775 Full-Size SBC User’s Manual
Configuring SATA for RAID Function
80
After the creation is completed, you can see detailed information about
the RAID Array in the DISK/VOLUME INFORMATION section,
including RAID mode, disk block size, disk name, and disk capacity,
etc.
Figure 9
Page 87
SHB101 LGA775 Full-Size SBC User’s Manual
Configuring SATA for RAID Function
81
Delete RAID Volume
If you want to delete a RAID volume, select the Delete RAID Volume
option in Main Menu. Press ENTER and follow on-screen instructions.
Figure 10
Please press [ESC] to exit theICH9R RAID BIOS utility.
Now, you can proceed to install a SATA driver controller and the
operating system.
(4) Making a SATA Driver Disk
To install the operating system onto a serial ATA hard disk
successfully, you need to install the SATA controller driver during the
OS installation. Without the driver, the hard disk may not be
recognized during the Windows setup process. First of all, please
format a blank floppy disk. Secondly, follow up these steps below to
produce a SATA driver disk.
Page 88
SHB101 LGA775 Full-Size SBC User’s Manual
Configuring SATA for RAID Function
82
(4)-1 Users can insert the Driver CD and the formatted blank floppy
disk in another system. And then, please execute the
f6flpy32.exe file in the folder of the Driver CD.
Note Please execute the f6flpy64. exe file, if installing 64-
bit Windows Operating System.
(4)-2 When this screen pops out, please click the “CONFIRM”
button.
Page 89
SHB101 LGA775 Full-Size SBC User’s Manual
Configuring SATA for RAID Function
83
(4)-3 When the RAID Driver is written to the floppy disk, the SATA
driver disk is completed.
Note Please execute the f6flpy 64.exe file, if installing 64-bit
Windows Operating System.
(5) Installing the SATA controller driver during the OS installation
Now, the SATA driver disk is ready, and BIOS settings configured, you
can proceed to install Windows 2000/XP onto your SATA hard drive
using the SATA driver. Here is an example for Windows XP installation.
Page 90
SHB101 LGA775 Full-Size SBC User’s Manual
Configuring SATA for RAID Function
84
(5)-1 Restart your system to boot the Windows 2000/XP Setup disk,
and press F6 butoon button as soon as you see the message
"Press F6 if you need to install a 3rd party SCSI or RAID
driver" (as Figure 11). After pressing the F6 button, there will
be a few moments for some files being loaded before next
screen appears.
Figure 11
(5)-2 When you see the screen below, insert the floppy disk
containing the SATA driver and press “S” (as Figure 12).
Figure 12
Page 91
SHB101 LGA775 Full-Size SBC User’s Manual
Configuring SATA for RAID Function
85
(5)-3 If the Setup correctly recognizes the driver of the floppy disk,
a controller menu (as Figure 13) will appear below. Use the
ARROW keys to select Intel(R) 82801IR/ IHO SATA RAID
Controller and press ENTER. Then it will begin to load the
SATA driver from the floppy disk.
Figure 13
Note If a message on the screen saying that one or some file(s)
cannot be found, please check the floppy disk or copy the
correct SATA driver again from the driver CD.
Page 92
SHB101 LGA775 Full-Size SBC User’s Manual
PICMG v1.3 Interface Definition
86
APPENDIX D
PICMG v1.3 INTERFACE DEFINITION
x16 PCIe Connector A x16 PCIe Connector C
Side B Side A
Side B Side A
1 N.C N.C 1 USB0P GND
2 GND GND 2 USB0N GND
3 N.C N.C 3 GND USB1P
4 N.C N.C 4 GND USB1N
5 N.C WAKE# 5 USB2P GND
6 PWRBT# PME# 6 USB2N GND
7 PWRGD PSON# 7 GND USB3P
8 SHB_RST# PERST# 8 GND USB3N
9 CFG0 CFG1 9 USBOC0# GND
10 CFG2 CFG3 10 GND USBOC1#
11 RSVD GND 11 USBOC2# GND
Mechanical Key
12 GND N.C 12 GND USBOC3#
13 b_PETp0 GND 13 N.C GND
14 b_PETn0 GND 14 N.C GND
15 GND b_PERp0 15 GND N.C
16 GND b_PERn0 16 GND N.C
17 b_PETp1 GND 17 N.C GND
18 b_PETn1 GND 18 N.C GND
19 GND b_PERp1 19 GND N.C
20 GND b_PERn1 20 GND N.C
21 b_PETp2 GND 21 N.C GND
22 b_PETn2 GND 22 N.C GND
23 GND b_PERp2 23 GND N.C
24 GND b_PERn2 24 GND N.C
25 b_PETp3 GND 25 N.C GND
26 b_PETn3 GND 26 N.C GND
27 GND b_PERp3 27 GND N.C
28 GND b_PERn3 28 GND N.C
29 REFCLK0+ GND 29 N.C GND
30 REFCLK0- GND 30 N.C GND
Mechanical Key
Page 93
SHB101 LGA775 Full-Size SBC User’s Manual
PICMG v1.3 Interface Definition
87
31 GND REFCLK1+ 31 N.C N.C
32 RSVD REFCLK1- 32 N.C N.C
33 REFCLK2+ GND 33 N.C N.C
34 REFCLK2- GND 34 N.C GND
35 GND REFCLK3+ 35 N.C GND
36 RSVD REFCLK3- 36 GND N.C
37 REFCLK4+ GND 37 GND N.C
38 REFCLK4- GND 38 N.C GND
39 GND N.C 39 N.C GND
40 RSVD N.C 40 GND N.C
41 N.C GND 41 GND N.C
42 N.C GND 42 +3.3V +3.3V
43 GND N.C 43 +3.3V +3.3V
44 GND N.C 44 +3.3V +3.3V
45 a_PETp0 GND 45 +3.3V +3.3V
46 a_PETn0 GND 46 +3.3V +3.3V
47 GND a_PERp0 47 +3.3V +3.3V
48 GND a_PERn0 48 +3.3V +3.3V
49 a_PETp1 GND 49 +3.3V +3.3V
50 a_PETn1 GND 50 +3.3V +3.3V
51 GND a_PERp1 51 GND GND
52 GND a_PERn1 52 GND GND
53 a_PETp2 GND 53 GND GND
54 a_PETn2 GND 54 GND GND
55 GND a_PERp2 55 GND GND
56 GND a_PERn2 56 GND GND
57 a_PETp3 GND 57 GND GND
58 a_PETn3 GND 58 GND GND
59 GND a_PERp3 59 +5V +5V
60 GND a_PERn3 60 +5V +5V
61 a_PETp4 GND 61 +5V +5V
62 a_PETn4 GND 62 +5V +5V
63 GND a_PERp4 63 GND GND
64 GND a_PERn4 64 GND GND
65 a_PETp5 GND 65 GND GND
66 a_PETn5 GND 66 GND GND
67 GND a_PERp5 67 GND GND
68 GND a_PERn5 68 GND GND
Mechanical Key
Page 94
SHB101 LGA775 Full-Size SBC User’s Manual
PICMG v1.3 Interface Definition
88
69 a_PETp6 GND 69 GND GND
70 a_PETn6 GND 70 GND GND
71 GND a_PERp6 71 GND GND
72 GND a_PERn6 72 GND GND
73 a_PETp7 GND 73 +12V +12V
74 a_PETn7 GND 74 +12V +12V
75 GND a_PERp7 75 +12V +12V
76 GND a_PERn7 76 +12V +12V
77 N.C GND 77 +12V +12V
78 +3.3V +3.3V 78 +12V +12V
79 +3.3V +3.3V 79 +12V +12V
80 +3.3V +3.3V 80 +12V +12V
81 +3.3V +3.3V 81 +12V +12V
82 RSVD RSVD 82 +12V +12V
X8 PCIe Connector B X8 PCIe Connector D
Side B Side A
Side B Side A
1 +5Vaux +5Vaux 1 INTB# INTA#
2 GND N.C 2 INTD# INTC#
3 a_PETp8 GND 3 GND N.C
4 a_PETn8 GND 4 REQ3# GNT3#
5 GND a_PERp8 5 REQ2# GNT2#
6 GND a_PERn8 6 PCI_RST# GNT1#
7 a_PETp9 GND 7 REQ1# GNT0#
8 a_PETn9 GND 8 REQ0# SERR#
9 GND a_PERp9 9 N.C +3.3V
10 GND a_PERn9 10 GND N.C
11 N.C GND 11 N.C GND
Mechanical Key
12 GND N.C 12 CLKC CLKD
13 a_PETp10 GND 13 GND +3.3V
14 a_PETn10 GND 14 CLKA CLKB
15 GND a_PERp10 15 +3.3V GND
16 GND a_PERn10 16 AD31 GND
17 a_PETp11 GND 17 AD29 +3.3V
18 a_PETn11 GND 18 N.C AD30
19 GND a_PERp11 19 AD27 AD28
20 GND a_PERn11 20 AD25 GND
21 a_PETp12 GND 21 GND AD26
Mechanical Key
Page 95
SHB101 LGA775 Full-Size SBC User’s Manual
PICMG v1.3 Interface Definition
89
22 a_PETn12 GND 22 C/BE3# AD24
23 GND a_PERp12 23 AD23 +3.3V
24 GND a_PERn12 24 GND AD22
25 a_PETp13 GND 25 AD21 AD20
26 a_PETn13 GND 26 AD19 N.C
27 GND a_PERp13 27 +5V AD18
28 GND a_PERn13 28 AD17 AD16
29 a_PETp14 GND 29 C/BE2# GND
30 a_PETn14 GND 30 PCI_PRST# FRAME#
31 GND a_PERp14 31 IRDY# TRDY#
32 GND a_PERn14 32 DEVSEL# +5V
33 a_PETp15 GND 33 LOCK# STOP#
34 a_PETn15 GND 34 PERR# GND
35 GND a_PERp15 35 GND C/BE1#
36 GND a_PERn15 36 PAR AD14
37 N.C GND 37 N.C GND
38 N.C N.C 38 GND AD12
39 GND GND 39 AD15 AD10
40 GND GND 40 AD13 GND
41 GND GND 41 GND AD09
42 GND GND 42 AD11 C/BE0#
43 GND GND 43 AD08 GND
44 +12V +12V 44 GND AD06
45 +12V +12V 45 AD07 AD05
46 +12V +12V 46 AD04 GND
47 +12V +12V 47 GND AD02
48 +12V +12V 48 AD03 AD01
49 +12V +12V 49 AD00 GND
Note Please contact your vendor to get the backplane
design guide if it’s required. The backplane design
guide is NDA required.
Loading...