Page 1
SBC84600 Series Quick Installation Guide
drivers, and utilities for the SBC84600 Series CPU Card.
Please refer to the Product Information CD for the complete version of the User’s Manual,
I.
Checklist
SBC84600 Board x 1
Quick Installation Guide x 1
Product Information CD-ROM x 1
2-pin jumper cap, Pitch=2.54mm x 5
2-pin jumper cap, Pitch=2.0mm x 10
3mm screw nuts x 2
PS/2 Keyboard/Mouse adapter x 1
2.5” & 3.5” HDD cable x 1
Power Cable 8 Pin x 1
COM+Printer extension cables
with bracket, Pitch=2.0mm x 1
COM extension cables with
bracket, Pitch=2.0mm x 1
FPC cable for extra display
features x 2
Audio Cable x 1 (for
SBC84600VEA Series
Products only)
If there are damaged or missing parts, contact your supplier
and/or dealer immediately. Do not attempt to apply power to
the board if there is damage to any of its components.
Note: The Windows XP Pro/home SP2 edition is not
supported by VIA non-Nehemiah core version processors
which are adopted by SBC84600VEA/VE-400 and
SBC84600VEA/VE-800. For more information please
reference
http://support.microsoft.com/kb/893356
Jumper Settings
II.
Before turning on the power to the S BC84600 Series,
please make sure that all jumpers are on their default
settings as listed on the table below.
Jumper Default Setting Jumper Setting
JP1
JP2
JP3
JP4
JP5
JP6
JP7
JP8
JP9
©Copyright 2005 AXIOMTEK Co., Ltd.
Version A7 September 2005
Printed in Taiwan
94284600060E
Watchdog Trigger Mode: Disabled Open
Flat Panel Power Selection: VDDM at 5V Short 1-2
Clear CMOS Setting: Norma Short 1-2
COM2 Port Setting: RS-232 Short 1-2
COM2 Port Setting: RS-232 Short 3-5, 4-6
COM2 Port Setting: RS-232 Short 3-5, 4-6
Power Supply Selection: AT power supply Short 1-2
COM1 Signal/+5V Selection
Default: COM Signal
COM2 Signal/+5V Selection
Default: COM Signal
Short 2-3
Short 2-3
1
Page 2
SBC84600 Series Quick Installation Guide
JP10
JP11
JP12
III.
Connectors Label
44 Pin IDE Connector CN1 TV Connector CN14
44-pin LCD Connector CN2 FDD Connector CN15
Flat Panel Bezel Connector CN3 USB connector USB1, USB2
20-pin LCD Connector CN4 VGA CRT Connector VGA1
CPU FAN +5V Connector CN5 Ethernet Connector LAN1
Printer Port Connector CN7 PC/104 Connector J1, J2
Digital I/O Port Connector CN8 COM Connector COM1
COM4 Signal/+5V Selection
Default: COM Signal
COM3 Signal/+5V Selection
Default: COM Signal
Compact Flash Voltage Selection
Default: 3.3V
SBC84600 Connectors
Connectors Label
Short 2-3
Short 2-3
Short 1-2
The complete version of the User’s Manual, along with the drivers/utilities software
programs are in the Product Information CD of the SBC84600 Series CPU Card.
ATX Power On/Off Button CN9 COM Connector COM2
Power Input Connectors CN10 COM Connector COM3
IrDA Connector CN11 COM Connector COM4
AC97 Link Interface CN12 Compact Flash Connector CF1
Keyboard and Mouse
Connector
Temperature sensor
IV. AX93102
Connectors Label
CD AUDIO INPUT CN2 AUDIO PHONE JACK CON1
CN13 VIDEO Connector VIDEO1
JP17
Connector
Connectors Label
For SBC84600VEA series products only.
©Copyright 2005 AXIOMTEK Co., Ltd.
2
Version A7 September 2005
Printed in Taiwan
94284600060E
Page 3
SBC84600 Series Quick Installation Guide
Additional Information
V.
The complete version of the User’s Manual, along with the drivers/utilities software
programs are in the Product Information CD of the SBC84600 Series CPU Card.
VI.
User’s Manual and other documents are in
Acrobat PDF format. The Product Information
CD contains the Adobe Acrobat 3.0 Reader
installation software for user’s convenience.
Board Layout
©Copyright 2005 AXIOMTEK Co., Ltd.
Version A7 September 2005
Printed in Taiwan
94284600060E
3
Page 4
SBC84600 Series Quick Installation Guide
VII Installation Procedures
Please follow the steps below to install the SBC84600 onto a
chassis:
1. Remove the pillar (a) from the SBC84600 as shown in
Figure 1.
The complete version of the User’s Manual, along with the drivers/utilities software
programs are in the Product Information CD of the SBC84600 Series CPU Card.
(a)
Figure 1.
2. Screw the pillar (a) removed from the SBC84600 and
another three pillars (c), which have same height with
the pillar (a), to the chassis as shown in the Figure 2.
3. Use the bolt (b) on the SBC84600 module to screw
the module with the pillar (a) on the chassis.
©Copyright 2005 AXIOMTEK Co., Ltd.
4
Version A7 September 2005
Printed in Taiwan
94284600060E
Page 5
SBC84600 Series Quick Installation Guide
4. Screw three proper bolts (d) to the other three pillars
The complete version of the User’s Manual, along with the drivers/utilities software
programs are in the Product Information CD of the SBC84600 Series CPU Card.
(c) to secure the board with the chassis.
(d)
(b)
(a)
(c)
Figure 2.
©Copyright 2005 AXIOMTEK Co., Ltd.
Version A7 September 2005
Printed in Taiwan
94284600060E
5
Page 6
SBC84600 Series Quick Installation Guide
(e)
(f)
5. If the Audio kit, AX93102, is used, plug the 10-pin
female box-header of the AX93102 onto the 10-pin
male box-header of the SBC84600 as shown on
Figure 3.
6. Make sure the spacer support (e) fit into the hole (f)
on the SBC84600.
AX93102
10-pin female
box-header
10-pin male
box-header
The complete version of the User’s Manual, along with the drivers/utilities software
programs are in the Product Information CD of the SBC84600 Series CPU Card.
6
©Copyright 2005 AXIOMTEK Co., Ltd.
Version A7 September 2005
Printed in Taiwan
94284600060E
Loading...